The previous patch "c5ccf2ad3d33 (Input: synaptics-rmi4 - switch to
reduced reporting mode)" enabled reduced reporting mode unintentionally
on some devices, if the firmware was configured with default Delta X/Y
threshold values. The result unintentionally degrade the performance of
some touchpads.
This patch checks to see that the driver is modifying the delta X/Y
thresholds before modifying the reporting mode.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Fixes: c5ccf2ad3d ("Input: synaptics-rmi4 - switch to reduced reporting mode")
Link: https://lore.kernel.org/r/20200312005549.29922-1-aduggan@synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the distance thresholds are set the controller must be in reduced
reporting mode for them to have any effect on the interrupt generation.
This has a potentially large impact on the number of events the host
needs to process.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20200120111628.18376-1-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The F54 Report Data is apparently read through a fifo and for
the smbus protocol that means that between reading a block of 32
bytes the rmiaddr shouldn't be incremented. However, changing
that causes other non-fifo reads to fail and so that change was
reverted.
This patch changes just the F54 function and it now reads 32 bytes
at a time from the fifo, using the F54_FIFO_OFFSET to update the
start address that is used when reading from the fifo.
This has only been tested with smbus, not with i2c or spi. But I
suspect that the same is needed there since I think similar
problems will occur there when reading more than 256 bytes.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Link: https://lore.kernel.org/r/20200115124819.3191024-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit a284e11c37.
This causes problems (drifting cursor) with at least the F11 function that
reads more than 32 bytes.
The real issue is in the F54 driver, and so this should be fixed there, and
not in rmi_smbus.c.
So first revert this bad commit, then fix the real problem in F54 in another
patch.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Fixes: a284e11c37 ("Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200115124819.3191024-2-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This increment of rmi_smbus in rmi_smb_read/write_block() causes
garbage to be read/written.
The first read of SMB_MAX_COUNT bytes is fine, but after that
it is nonsense. Trial-and-error showed that by dropping the
increment of rmiaddr everything is fine and the F54 function
properly works.
I tried a hack with rmi_smb_write_block() as well (writing to the
same F54 touchpad data area, then reading it back), and that
suggests that there too the rmiaddr increment has to be dropped.
It makes sense that if it has to be dropped for read, then it has
to be dropped for write as well.
It looks like the initial work with F54 was done using i2c, not smbus,
and it seems nobody ever tested F54 with smbus. The other functions
all read/write less than SMB_MAX_COUNT as far as I can tell, so this
issue was never noticed with non-F54 functions.
With this change I can read out the touchpad data correctly on my
Lenovo X1 Carbon 6th Gen laptop.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/8dd22e21-4933-8e9c-a696-d281872c8de7@xs4all.nl
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
F34 is a bit special as it reinitializes the device and related driver
structs during the firmware update. This clears the fn_irq_mask which
will then prevent F34 from receiving further interrupts, leading to
timeouts during the firmware update. Make sure to reinitialize the
IRQ enables at the appropriate times.
The issue is in F34 code, but the commit in the fixes tag exposed the
issue, as before this commit things would work by accident.
Fixes: 363c53875a (Input: synaptics-rmi4 - avoid processing unknown IRQs)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191129133514.23224-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The v4l2-compliance utility reported several V4L2 API compliance
issues:
- the sequence counter wasn't filled in
- the sequence counter wasn't reset to 0 at the start of streaming
- the returned field value wasn't set to V4L2_FIELD_NONE
- the timestamp wasn't set
- the payload size was undefined if an error was returned
- min_buffers_needed doesn't need to be initialized
Fix these issues.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de
Link: https://lore.kernel.org/r/20191119105118.54285-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver forgets to destroy workqueue in remove() similarly to what is
done when probe() fails. Add a call to destroy_workqueue() to fix it.
Since unregistration will wait for the work to finish, we do not need to
cancel/flush the work instance in remove().
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191114023405.31477-1-hslester96@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver for F54 just polls the status and doesn't even have a IRQ
handler registered. Make sure to disable all F54 IRQs, so we don't crash
the kernel on a nonexistent handler.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191105114402.6009-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The body of the for loop is only ever run once as the second standard_report
element is never changed from its initial zero init, so the loop condition is
never satisfies after the first run. Equally the start member of the first
element is never changed from 0, so the index offset is always a constant 0.
Remove this needless obfuscation of the code and write it in a straight
forward manner.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191104114454.10500-3-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently, rmi_f11_attention() and rmi_f12_attention() functions update
the attn_data data pointer and size based on the size of the expected
size of the attention data. However, if the actual valid data in the
attn buffer is less then the expected value then the updated data
pointer will point to memory beyond the end of the attn buffer. Using
the calculated valid_bytes instead will prevent this from happening.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191025002527.3189-3-aduggan@synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes an issue seen on HID touchpads which report finger
positions using RMI4 Function 12. The issue manifests itself as
spurious button presses as described in:
https://www.spinics.net/lists/linux-input/msg58618.html
Commit 24d28e4f12 ("Input: synaptics-rmi4 - convert irq distribution
to irq_domain") switched the RMI4 driver to using an irq_domain to handle
RMI4 function interrupts. Functions with more then one interrupt now have
each interrupt mapped to their own IRQ and IRQ handler. The result of
this change is that the F12 IRQ handler was now getting called twice. Once
for the absolute data interrupt and once for the relative data interrupt.
For HID devices, calling rmi_f12_attention() a second time causes the
attn_data data pointer and size to be set incorrectly. When the touchpad
button is pressed, F30 will generate an interrupt and attempt to read the
F30 data from the invalid attn_data data pointer and report incorrect
button events.
This patch disables the F12 relative interrupt which prevents
rmi_f12_attention() from being called twice.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reported-by: Simon Wood <simon@mungewell.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191025002527.3189-2-aduggan@synaptics.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The video buffer used by the queue is a vb2_v4l2_buffer, not a plain
vb2_buffer. Using the wrong type causes the allocation of the buffer
storage to be too small, causing a out of bounds write when
__init_vb2_v4l2_buffer initializes the buffer.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 3a762dbd53 ("[media] Input: synaptics-rmi4 - add support for F54 diagnostics")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191104114454.10500-1-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
rmi_process_interrupt_requests() calls handle_nested_irq() for
each interrupt status bit it finds. If the irq domain mapping for
this bit had not yet been set up, then it ends up calling
handle_nested_irq(0), which causes a NULL pointer dereference.
There's already code that masks the irq_status bits coming out of the
hardware with current_irq_mask, presumably to avoid this situation.
However current_irq_mask seems to more reflect the actual mask set
in the hardware rather than the IRQs software has set up and registered
for. For example, in rmi_driver_reset_handler(), the current_irq_mask
is initialized based on what is read from the hardware. If the reset
value of this mask enables IRQs that Linux has not set up yet, then
we end up in this situation.
There appears to be a third unused bitmask that used to serve this
purpose, fn_irq_bits. Use that bitmask instead of current_irq_mask
to avoid calling handle_nested_irq() on IRQs that have not yet been
set up.
Signed-off-by: Evan Green <evgreen@chromium.org>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Link: https://lore.kernel.org/r/20191008223657.163366-1-evgreen@chromium.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The function rmi_2d_sensor_set_input_params is declared static and marked
EXPORT_SYMBOL_GPL, which is at best an odd combination. Because the
function is not used outside of the drivers/input/rmi4/rmi_2d_sensor.c
file it is defined in, this commit removes the EXPORT_SYMBOL_GPL() marking.
Signed-off-by: Denis Efremov <efremov@linux.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl0idTweHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGZesIAJDKicw2Voyx8K8m
3pXSK+71RuO/d3Y9M51mdfTMKRP4PHR9/4wVZ9wHPwC4dV6wxgsmIYCF69a1Wety
LD1MpDCP1DK5wVfPNKVX2xmj7ua6iutPtSsJHzdzM2TlscgsrFKjmUccqJ5JLwL5
c34nqwXWnzzRyI5Ga9cQSlwzAXq0vDHXyML3AnCosSsLX0lKFrHlK1zttdOPNkfj
dXRN62g3q+9kVQozzhDXb8atZZ7IkBk8Q0lujpNXW83Ci1VjaVNv3SB8GZTXIlLj
U15VdyuwfJDfpBgFBN6/unzVaAB6FFrEKy0jT1aeTyKarMKDKgOnJjn10aKjDNno
/bXsKKc=
=TVqV
-----END PGP SIGNATURE-----
Merge tag 'v5.2' into next
Sync up with mainline to resolve conflicts in iforce driver.
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/input/rmi4/rmi_f12.c: In function rmi_f12_read_sensor_tuning:
drivers/input/rmi4/rmi_f12.c:76:6: warning: variable sensor_flags set but not used [-Wunused-but-set-variable]
It's not used since introduction in
commit b43d2c1e93 ("Input: synaptics-rmi4 - add support for F12")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlzPgx4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGf8IH/jkes7tKj7pWfsNW
uMjbm5T+Jh26sntRj+3OWOxcHRlejTH2MammnA9GIspBfF5LXkkmk40eeYhnTiVN
SzZqSFNLO0tRIHsd7hbxhTyOzHcWmymoEqY1jb8IPMyM5BB8TiS+1C0AVlOW1P/f
TO1gRcrddu1j80uCInRzNX5eAlvfrU4nK6GxjFdmy6b/bgYQiPfNA+jZbCWxc+48
ivBn9ifFCKlDzki81Dmi5R98c4R9UU3Z5LsqHjC4RIV64hpHdEwnOIkXQ+XY5mW9
7EOT1v6hJGch1ulH27ypgSZ7fhSCSYQJIY/LNWeJtdVclvlVepb2Vrx/8NUN60qC
E0MEn1Y=
=mCkr
-----END PGP SIGNATURE-----
Merge tag 'v5.1' into next
Sync up with mainline to bring in the latest APIs.
Currently any changed config register values don't take effect, as the
function to write them back is called with the wrong register offset.
Fixes: ff8f83708b (Input: synaptics-rmi4 - add support for 2D
sensors and F11)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do not enumerate all formats, some of which the device may not even
support. Instead, only report the one fixed format of the currently
selected input that will survive try_fmt/s_fmt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver doesn't set an initial video format until s_input is called:
$ v4l2-ctl -d /dev/v4l-touch0 --get-input
Video input : 0 (Normalized 16-Bit Image: ok)
$ v4l2-ctl -d /dev/v4l-touch0 --get-fmt-video
Width/Height : 0/0
Pixel Format : ''
[...]
$ v4l2-ctl -d /dev/v4l-touch0 --set-input 0
Video input set to 0 (Normalized 16-Bit Image: Touch, ok)
$ v4l2-ctl -d /dev/v4l-touch0 --get-fmt-video
Width/Height : 71/40
Pixel Format : 'TD16'
[...]
To fix this, initialize the video format to input 0 during probe.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The RMI4 function structure has been released in rmi_register_function
if error occurs. However, it will be released again in the function
rmi_create_function, which may result in a double-free bug.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- the main change is a fix for my brain-dead patch to PS/2 button
reporting for some protocols that made it in 4.17
- there is a new driver for Spreadtum vibrator that I intended to send
during merge window but ended up not sending the 2nd pull request.
Given that this is a brand new driver we should not see regressions
here
- a fixup to Elantech PS/2 driver to avoid decoding errors on Thinkpad
P52
- addition of few more ACPI IDs for Silead and Elan drivers
- RMI4 is switched to using IRQ domain code instead of rolling its own
implementation
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - fix button reporting for basic protocols
Input: xpad - fix GPD Win 2 controller name
Input: elan_i2c_smbus - fix more potential stack buffer overflows
Input: elan_i2c - add ELAN0618 (Lenovo v330 15IKB) ACPI ID
Input: elantech - fix V4 report decoding for module with middle key
Input: elantech - enable middle button of touchpads on ThinkPad P52
Input: do not assign new tracking ID when changing tool type
Input: make input_report_slot_state() return boolean
Input: synaptics-rmi4 - fix axis-swap behavior
Input: synaptics-rmi4 - fix the error return code in rmi_probe_interrupts()
Input: synaptics-rmi4 - convert irq distribution to irq_domain
Input: silead - add MSSL0002 ACPI HID
Input: goldfish_events - fix checkpatch warnings
Input: add Spreadtrum vibrator driver
The documentation for the touchscreen-swapped-x-y property states that
swapping is done after inverting if both are used. RMI4 did it the other
way around, leading to inconsistent behavior with regard to other
touchscreens.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The error return code PTR_ERR(data->irqdomain) is always 0 since
data->irqdomain is equal to NULL in this error handling case.
Fixes: 24d28e4f12 ("Input: synaptics-rmi4 - convert irq distribution to irq_domain")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the RMI driver to use the standard mechanism for
distributing IRQs to the various functions.
Tested on:
* S7300 (F11, F34, F54)
* S7817 (F12, F34, F54)
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Acked-by: Christopher Heiny <cheiny@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When extending the rmi_spi buffers, we must check that no out of memory
error occurs, otherwise we may access data above the currently allocated
memory.
Propagate the error code returned by 'rmi_spi_manage_pools()' instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since the sysfs attribute hangs off the RMI bus, which doesn't go away during
firmware flash, it needs to be explicitly removed, otherwise we would try and
register the same attribute twice.
This reverts commit 36a44af5c1.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To ease analyzing boot behavior from logs, let's log when we are about to
register the pass-through serio port.
Also, let's drop "Synaptics" prefix from the port name, as RMI4 is good
enough indicator already, and having the prefix means that the name does
not fit into serio->name field. While at it move from hard-coded seio->phys
to one mentioning the sensor ID (such as "rmi4-00.fn03/serio0").
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently we register the pass-through serio port when we probe the F03 RMI
function, and then, in sensor configure phase, we unmask interrupts.
Unfortunately this is too late, as other drivers are free probe devices
attached to the serio port as soon as it is probed. Because interrupts are
masked, the IO times out, which may result in not being able to detect
trackpoints on the pass-through port.
To fix the issue we implement open() and close() methods for the
pass-through serio port and unmask interrupts from there. We also move
creation of the pass-through port form probe to configure stage, as RMI
driver does not enable transport interrupt until all functions are probed
(we should change this, but this is a separate topic).
We also try to clear the pending data before unmasking interrupts, because
some devices like to spam the system with multiple 0xaa 0x00 announcements,
which may interfere with us trying to query ID of the device.
Fixes: c5e8848fc9 ("Input: synaptics-rmi4 - add support for F03")
Cc: stable@vger.kernel.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We want to free memory reserved for interrupt mask handling only after we
free functions, as function drivers might want to mask interrupts. This is
needed for the followup patch to the F03 that would implement unmasking and
masking interrupts from the serio pass-through port open() and close()
methods.
Cc: stable@vger.kernel.org
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MODULE_VERSION is useless for in-kernel drivers, so just remove all
usage of it in the rmi4 drivers. Now that this is gone, the
RMI_DRIVER_VERSION macro was also removed as it was pointless.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This duplicate include has been found with scripts/checkincludes.pl but
it has been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Patchwork-Id: 10092051
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZ/30WAAoJEHm+PkMAQRiG1YkIAIVgcZS9SPzjcH+/NpcNJ4wv
Bp8xyfj/X6Eswn63ebrV/qij65Esmha7wnSREcFqrfNecRwOAdvYCjj20jqKGws2
p03sOS4aVSpJSQcqJ9sdF3Xx/P7CcK4IAjr0ihQbqozXiZAgVzTlYJwB+ErBMWFU
6NFYXg/Xp7FJXJ0o14yHpZ4RqgbLV95CgFIG9hzwvCibsW6ZBvGtYBD99IjeojPg
rw+B+Osck7XjC6IHqF/u760nTOaP8vVlTrCRqvFityGS9ZFQZDzEKYqxYgk8cVFC
jzR3fuHiWiomhyP9dLUZn6UuYQTaThhY58LvsEwV0JVJH9mUwcA4u5nO0wDUCO4=
=hhQa
-----END PGP SIGNATURE-----
Merge tag 'v4.14-rc8' into next
Merge with mainline to bring in SPDX markings to avoid annoying merge
problems when some header files get deleted.
Some Synaptics devices, such as LEN0073, use SMBUS version 3.
Signed-off-by: Yiannis Marangos <yiannis.marangos@gmail.com>
Acked-by: Benjamin Tissoires <benjamion.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By convention the first 6 bits of F30 Ctrl 2 and 3 are used to signify
GPIOs which are connected to buttons. Additional GPIOs may be used as
input GPIOs to signal the touch controller of some event
(ie disable touchpad). These additional GPIOs may meet the criteria of
a button in rmi_f30_is_valid_button() but should not be considered
buttons. This patch limits the GPIOs which are mapped to buttons to just
the first 6.
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reported-by: Daniel Martin <consume.noise@gmail.com>
Tested-by: Daniel Martin <consume.noise@gmail.com>
Acked-By: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The array rmi_f54_report_type_names is local to the source and does
not need to be in global scope, so make it static. Also make the array
const char * const.
Cleans up sparse warning:
symbol 'rmi_f54_report_type_names' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
