It does not make much sense to keep the current virtual wiphy implementation
any longer - it adds significant complexity, has very few users and is still
very experimental. At some point in time, it will be replaced by a proper
implementation in mac80211.
By making the code easier to read and maintain, removing virtual wiphy support
helps with fixing the remaining driver issues and adding further improvements.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of spreading ath_wake_mac80211_queue() calls over multiple places
in the tx path that process the tx queue for completion, call it only
where the pending frames counter gets decremented, eliminating some
redundant checks.
To prevent queue draining from waking the queues prematurely (e.g. during
a hardware reset), reset the queue stop state when draining all queues,
as the caller in main.c will run ieee80211_wake_queues(hw) anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.
This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.
ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.
Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.
Cc: stable@kernel.org
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TCP is going to record metrics for the connection,
so pre-COW the route metrics at route cache entry
creation time.
This avoids several atomic operations that have to
occur if we COW the metrics after the entry reaches
global visibility.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use net_device_stats instance from the struct net_device.
Signed-off-by: Denis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing __rcu annotations and helpers.
minor : Fix some rcu_dereference() calls in macvtap
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c6d14c8456 (net: Introduce for_each_netdev_rcu() iterator)
added a race in dev_seq_next().
The rcu_dereference() call should be done _before_ testing the end of
list, or we might return a wrong net_device if a concurrent thread
changes net_device list under us.
Note : discovered thanks to a sparse warning :
net/core/dev.c:3919:9: error: incompatible types in comparison expression
(different address spaces)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please note that the IPSEC dst entry metrics keep using
the generic metrics COW'ing mechanism using kmalloc/kfree.
This gives the IPSEC routes an opportunity to use metrics
which are unique to their encapsulated paths.
Signed-off-by: David S. Miller <davem@davemloft.net>
They are bogus. The basic idea is that I wanted to make sure
that prefixed routes never bind to peers.
The test I used was whether RTF_CACHE was set.
But first of all, the RTF_CACHE flag is set at different spots
depending upon which ip6_rt_copy() caller you're talking about.
I've validated all of the code paths, and even in the future
where we bind peers more aggressively (for route metric COW'ing)
we never bind to prefix'd routes, only fully specified ones.
This even applies when addrconf or icmp6 routes are allocated.
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_expand_head() triggers a kmemcheck warning when copy of
skb_shared_info is done in pskb_expand_head()
This is because destructor_arg field is not necessarily initialized at
this point. Add kmemcheck_annotate_variable() call in __alloc_skb() to
instruct kmemcheck this is a normal situation.
Resolves bugzilla.kernel.org 27212
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=27212
Reported-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm testing an API that uses IFLA_AF_SPEC attribute.
In the rtnetlink core , the set_link_af() member
of the rtnl_af_ops struct receives the nested attribute
(as I expected), but the validate_link_af() member
receives the parent attribute.
IMO, this patch fixes this.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux network stack expects all GSO SKBs to have ip_summed ==
CHECKSUM_PARTIAL (which implies that the frame contains a partial
checksum) and the Xen network ring protocol similarly expects an SKB
which has GSO set to also have NETRX_csum_blank (which also implies a
partial checksum).
However there have been cases of buggy guests which mark a frame as
GSO but do not set csum_blank. If we detect that we a receiving such a
frame (which manifests as ip_summed != PARTIAL && skb_is_gso) then
force the SKB to partial and recalculate the checksum, since we cannot
rely on the peer having done so if they have not set csum_blank.
Add an ethtool stat to track occurances of this event.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: David Miller <davem@davemloft.net>
Cc: xen-devel@lists.xensource.com
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
net/econet/af_econet.c: In function ‘econet_sendmsg’:
net/econet/af_econet.c:494: warning: label ‘error’ defined but not used
net/econet/af_econet.c:268: warning: unused variable ‘sk’
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Phil Blundell <philb@gnu.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the RTAX_LOCKED metric to INETPEER_METRICS_NEW (basically,
all ones) on fresh inetpeer entries.
This way code can determine if default metrics have been loaded
in from a routing table entry already.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update maintainer's email address, webpage and align with renaming of
files.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.
Cc: stable@kernel.org
Tested-by: Sujith <m.sujith@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.
I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2
Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath5k version of ieee80211_generic_frame_duration() returns
an __le16 for standard modes but a cpu-endian int for turbo/half/
quarter rates. Make it always return cpu-endian values.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Review spotted a problem with the error handling in ath5k_hw_dma_stop:
a successful return from ath5k_hw_stop_tx_dma will be treated as
an error, so we always bail out of the loop after processing a single
active queue. As a result, we may not actually stop some queues during
reset.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the source code from Realtek was prepared for kernel inclusion,
some routines were refactored to reduce the level of indentation. This
patch repairs errors introduced in that process.
Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit 'ath9k: Add more information to debugfs xmit file.' added more
debug counters to ath9k and also added some lines of code to ath9k_hw.
Since ath9k_hw is also used by ath9k_htc, its code must not depend on ath9k
data structures. In this case it was not fatal, but it's still wrong, so
the code needs to be moved back to ath9k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"mac80211 will properly assign sequence numbers to QoS-data
frames but cannot do so correctly for non-QoS-data and
management frames because beacons need them from that counter
as well and mac80211 cannot guarantee proper sequencing."
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch syncs up the header files with
the project's main firmware carl9170fw.git.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Routing metrics are now copy-on-write.
Initially a route entry points it's metrics at a read-only location.
If a routing table entry exists, it will point there. Else it will
point at the all zero metric place-holder called 'dst_default_metrics'.
The writeability state of the metrics is stored in the low bits of the
metrics pointer, we have two bits left to spare if we want to store
more states.
For the initial implementation, COW is implemented simply via kmalloc.
However future enhancements will change this to place the writable
metrics somewhere else, in order to increase sharing. Very likely
this "somewhere else" will be the inetpeer cache.
Note also that this means that metrics updates may transiently fail
if we cannot COW the metrics successfully.
But even by itself, this patch should decrease memory usage and
increase cache locality especially for routing workloads. In those
cases the read-only metric copies stay in place and never get written
to.
TCP workloads where metrics get updated, and those rare cases where
PMTU triggers occur, will take a very slight performance hit. But
that hit will be alleviated when the long-term writable metrics
move to a more sharable location.
Since the metrics storage went from a u32 array of RTAX_MAX entries to
what is essentially a pointer, some retooling of the dst_entry layout
was necessary.
Most importantly, we need to preserve the alignment of the reference
count so that it doesn't share cache lines with the read-mostly state,
as per Eric Dumazet's alignment assertion checks.
The only non-trivial bit here is the move of the 'flags' member into
the writeable cacheline. This is OK since we are always accessing the
flags around the same moment when we made a modification to the
reference count.
Signed-off-by: David S. Miller <davem@davemloft.net>
On PPC for example, AER is not supported and we see unnecessary AER
error message without this patch:
bnx2 0003:01:00.1: pci_cleanup_aer_uncorrect_error_status failed 0xfffffffb
Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip's page tables did not set up properly on big endian machines,
causing EEH errors on PPC machines.
Reported-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like ipv4, we have to propagate the ipv6 route peer into
the ipsec top-level route during instantiation.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unused macros and cleanup buffer_type enumeration
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For events that include only the local struct as
their parameter, we can use DECLARE_EVENT_CLASS
and save quite some binary size across segments
as well lines of code.
text data bss dec hex filename
375745 19296 916 395957 60ab5 mac80211.ko.before
367473 17888 916 386277 5e4e5 mac80211.ko.after
-8272 -1408 0 -9680 -25d0 delta
Some more tracepoints with identical arguments
could be combined like this but for now this is
the one that benefits most.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mqprio_dump() should make sure all fields of struct tc_mqprio_qopt are
initialized.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pivots the tg3 driver to the new VLAN infrastructure.
All references to vlgrp have been removed. The driver still attempts to
disable VLAN tag stripping if CONFIG_VLAN_8021Q or
CONFIG_VLAN_8021Q_MODULE is not defined.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xt_connlimit normally records the "original" tuples in a hashlist
(such as "1.2.3.4 -> 5.6.7.8"), and looks in this list for iph->daddr
when counting.
When the user however uses DNAT in PREROUTING, looking for
iph->daddr -- which is now 192.168.9.10 -- will not match. Thus in
daddr mode, we need to record the reverse direction tuple
("192.168.9.10 -> 1.2.3.4") instead. In the reverse tuple, the dst
addr is on the src side, which is convenient, as count_them still uses
&conn->tuple.src.u3.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates copyrights and updates the tg3 version to 3.117.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a preprocessor naming bug for one of the EEE registers.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem where EEE will fail to work in certain
environments.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EEE interferes with the hardware's ability to loop a packet back to the
host. This patch disables the feature for the duration of the test.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
