It's a common operation for device drivers to retrive the data
member from of_device_id struct in their probe function.
Most driver end up doing:
const struct of_device_id *match;
match = of_match_device(driver_of_match, &pdev->dev);
driver->data = match->data;
With the of_device_get_match_data helper function all this can
done in one go.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
[robh: add missing inline to dummmy declaration]
Signed-off-by: Rob Herring <robh@kernel.org>
Commit 5590f3196b ("drivers/core/of: Add symlink to device-tree from
devices with an OF node") adds the symlink `of_node` for each device
pointing to it's device tree node while creating/initialising it.
However the devicetree sysfs is created and setup in of_init which is
executed at core_initcall level. For all the devices created before
of_init, the following error is thrown:
"Error -2(-ENOENT) creating of_node link"
Like many other components in driver model, initialize the sysfs support
for OF/devicetree from driver_init so that it's ready before any devices
are created.
Fixes: 5590f3196b ("drivers/core/of: Add symlink to device-tree from
devices with an OF node")
Suggested-by: Rob Herring <robh+dt@kernel.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Robert Schwebel <r.schwebel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
41f8bba7f5 ("of/pci: Add pci_register_io_range() and
pci_pio_to_address()") added support for systems with several I/O ranges
described by OF bindings. It modified pci_address_to_pio() look up the
io_range for a given CPU physical address, but the conversion was wrong.
Fix the conversion of address to I/O port.
[bhelgaas: changelog]
Fixes: 41f8bba7f5 ("of/pci: Add pci_register_io_range() and pci_pio_to_address()")
Signed-off-by: Zhichang Yuan <yuanzhichang@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
CC: stable@vger.kernel.org # v3.18+
Some Ethernet PHY devices/switches may not properly release the MDIO bus
during turn-around time, and fail to drive it low, which can be seen by
some controllers as a read failure, while the data clocked in is still
correct.
Add a boolean property "broken-turn-around" which is parsed by the
generic MDIO bus probing code and will set the corresponding bit in the
MDIO bus phy_ignore_ta_mask bitmask for MDIO bus drivers to utilize that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This defines a new compatible option for MFD devices "simple-mfd" that will
make the OF core spawn child devices for all subnodes of that MFD device.
It is optional but handy for things like syscon and possibly other
simpler MFD devices.
Since there was no file to put the documentation in, I took this opportunity
to make a small writeup on MFD devices and add the compatible definition
there.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Devicetree <devicetree@vger.kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- DT endianness specification bindings
- Big endian 8250 serial support
- DT overlay unittest updates
- Various DT doc updates
- Compile fixes for OF_IRQ=n
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVOG5kAAoJEMhvYp4jgsXihDgH/3pmPSjuRG1bhGssmnchHjWh
SU2eS2MZnlD60UqRt7jd3smCX2qL83tfwpFhOvCT9Mz775E7ggmYq9fS8pCYAbaD
x98mUrE2GzdUzlrL6RS8Z0ExjyGwbMoW3+cZtyPkmC6CsW0fwqEPmEyk7m+Hk8C3
w3pWG06o+G8UjiFmwbr8Pki2ykxvucr22NCzH4SS6bAD4QOrQO3v48QkUg7XFlVc
NHNzQbswL85uOJ7uuAbxg+s8TXkwcxUeMJEKldLrjuyppO3N1MjnOgCptnhVNOOb
zK+IsS378jMiNjAg2ui/BLH60N5yadkgk4+L4iPPy+y/yR61NCVXxRe11IQJxb0=
=rtv6
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
devicetree changes queued up for v4.1. Here are the highlights:
- Lots of unittest cleanup from Frank Rowand
- Bugfixes and updates to the of_graph code
- Tighten up of_get_mac_address() code
- Documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVMYiQAAoJEMWQL496c2LNyrcP/2acOKeyHk7zBVWxaYe6nO52
iwpDb+UDEdW+1Cx5e+OpF1gqoY7lJ2Q+Uvm65+z00a46Fnl0cWuSYFIV7e0wjE5/
3EAB4cQgiCzToDnbtCu4U6XlpNlQz/q85tV9X/EpYApHNb+BKN6RMzyIDm48lzJY
L6SG4fxFJVpeDxweZFGaWE9/Ildr4vOS+4GZpE0Az3iX2WDrQPioKjuOw8TeUHRO
xwvfv1TpyQFa2qHZLI4AmZSN8VJBw82OuAyZHAGsE4bekfafeqVFt0ZtYYoiAbIM
rw+dUCnWARc7gm8z2PaYnZGs8O++Flb03clDeFrdrvfZIewXWEkZ1TxrKIb9bLyP
A8tlSnbnCdXYSzyaFYH2TgUtc7gQosssfImuJjUq1qQkeEitLP6VzEsekN1h6sx7
axFiBdiCXPvn8ti+AlK9tYfSM0ZhAzvfpuLM0hpTAk3De3NfbJQiyp6eyXAInLne
cs9RGPXNPuKX0tISZ29vA8tmOSrDInfeEEW/Lqu4l+HedcLssWjReY0xVsZS3pbi
xGiD5/Ztdha9keTIQdW+7R0SE1YsZTpwZbQt0HeHcE+pzFPF/3TLIIIYhYRVSPsm
D+g5W+bVxht8NC380UEC8vpAyP1CYSnq/aVrDfJiXZVOS7b/dyZDk6Y6LSBOm9Em
9qLaPASncxVinaNcGlyj
=u6Zy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Here are the devicetree changes queued up for v4.1. Nothing really
exciting here. Rob has another few commits for big-endian attached
UARTs, but those will be sent in a separate merge request since they
haven't been as thoroughly tested as this batch.
Here are the highlights:
- lots of unittest cleanup from Frank Rowand
- bugfixes and updates to the of_graph code
- tighten up of_get_mac_address() code
- documentation updates"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/unittest: Fix of_platform_depopulate test case
of/unittest: early return from test skips tests
of/unittest: breadcrumbs to reduce pain of future maintainers
of/unittest: reduce checkpatch noise - line after declarations
of/unittest: typo in error string
of/unittest: add const where needed
of_net: factor out repetitive code from of_get_mac_address()
drivers/of: Add empty ranges quirk for PA-Semi
of: Allow selection of OF_DYNAMIC and OF_OVERLAY if OF_UNITTEST
of: Empty node & property flag accessors when !OF
of: Explicitly include linux/types.h in of_graph.h
dt-bindings: brcm: rationalize Broadcom documentation naming
of/unittest: replace 'selftest' with 'unittest'
Documentation: rename of_selftest.txt to of_unittest.txt
Documentation: update the of_selftest.txt
dt: OF_UNITTEST make dependency broken
MAINTAINERS: Pantelis Antoniou device tree overlay maintainer
of: Add of_graph_get_port_by_id function
of: Add for_each_endpoint_of_node helper macro
of: Decrement refcount of previous endpoint in of_graph_get_next_endpoint
Add two new facts to of_get_next_child() documentation:
* of_get_next_child() returns NULL when there is not next child
* of_get_next_child() decrements the refcount of prev
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Rob Herring <robh@kernel.org>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
Pull i2c updates from Wolfram Sang:
"Most notable:
- introducing the i2c_quirk infrastructure. Now, flaws of I2C
controllers can be described and the core will check if the flaws
collide with the messages to be sent
- wait_for_completion return type cleanup series
- new drivers for Digicolor, Netlogic XLP, Ingenic JZ4780
- updates to the I2C slave framework which include API changes. Its
only user was updated, too. Documentation was finally added
- changed dynamic bus numbering for the DT case. This could change
bus numbers for users. However, it fixes a collision where dynamic
and static busses request the same id.
- driver bugfixes, cleanups"
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller
of: Add vendor prefix 'netlogic'
i2c: davinci: use ICPFUNC to toggle I2C as gpio for bus recovery
i2c: davinci: use bus recovery infrastructure
i2c: change input parameter to i2c_adapter for prepare/unprepare_recovery
i2c: i2c-mux-gpio: remove error messages for probe deferrals
i2c: jz4780: Add i2c bus controller driver for Ingenic JZ4780
i2c: dln2: set the device tree node of the adapter
i2c: davinci: fixup wait_for_completion_timeout handling
i2c: mpc: Fix ISR return value
i2c: slave-eeprom: add more info when to increase the pointer
i2c: slave: add documentation for i2c-slave-eeprom
Documentation: i2c: describe the new slave mode
i2c: slave: rework the slave API
i2c: add support for the Digicolor I2C controller
i2c: busses with dynamic ids should start after fixed ids for DT
of: base: add function to get highest id of an alias stem
i2c: designware: Suppress error message if platform_get_irq() < 0
i2c: mpc: assign the correct prescaler from SVR
i2c: img-scb: fixup of wait_for_completion_timeout return handling
...
During the course of the overlay selftests some of them remain
applied. While this does not pose a real problem, make sure you track
them and destroy them at the end of the test.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The allocation size of device node path is off by one which drops the
'\0' terminator.
Signed-off-by: Ricky Liang <jcliang@chromium.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Provide a libfdt-based equivalent for of_device_is_big_endian(), suitable
for use in the early_init_* functions.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
SoC peripherals can come in several different flavors:
- little-endian: registers always need to be accessed in LE mode (so the
kernel should perform a swap if the CPU is running BE)
- big-endian: registers always need to be accessed in BE mode (so the
kernel should perform a swap if the CPU is running LE)
- native-endian: the bus will automatically swap accesses, so the kernel
should never swap
Introduce a function that checks an OF device node to see whether it
contains a "big-endian" or "native-endian" property. For the former case,
always return true. For the latter case, return true iff the kernel was
built for BE (implying that the BE MMIO accessors do not perform a swap).
Otherwise return false, assuming LE registers.
LE registers are assumed by default because most existing drivers (libahci,
serial8250, usb) always use readl/writel in the absence of instructions
to the contrary, so that will be our fallback.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Commit 51975db0b7 ("of/flattree: merge early_init_dt_scan_memory()
common code") consolidated some code from PowerPC (typically
big-endian), and ended-up adding a pr_debug() printing reg properties in
big-endian (DT native) format, not CPU endian.
This debug print suffers from two problems:
- we only print 4 "reg" values, while there could be more on typical
systems having multiple memory ranges
- we print these 4 "reg" values in FDT endianess, that is big-endian,
and these values could be confusing for little-endian configurations
Since we are already printing the base address and size of the memory
regions parsed by early_init_dt_scan_memory() later in a way that is
both endian correct, and takes into account arbitrary number of memory
banks, just remove that part of the debug print.
Suggested-by: Frank Rowand <frowand.list@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
If CONFIG_IRQ_DOMAIN=n:
drivers/of/irq.c: In function ‘of_irq_get’:
drivers/of/irq.c:406: error: implicit declaration of function ‘irq_find_host’
drivers/of/irq.c:406: warning: assignment makes pointer from integer without a cast
make[2]: *** [drivers/of/irq.o] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/cmd.c
net/core/fib_rules.c
net/ipv4/fib_frontend.c
The fib_rules.c and fib_frontend.c conflicts were locking adjustments
in 'net' overlapping addition and removal of code in 'net-next'.
The mlx4 conflict was a bug fix in 'net' happening in the same
place a constant was being replaced with a more suitable macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit, "of/unittest: early return from test skips tests"
exposed broken tests for the of_platform_unpopulate() function. The
problem was the populate and depopulate calls were not symmetrical like
they were intended to be, and unpopulate depends on the parent device to
have it's of_node pointer pointing to the parent device node. Fix these
bugs so that the test case works correctly.
In the process, the test_bus used as a container for the test devices
has been changed from a statically allocated struct device (which is
bad) to a properly allocated device with a .release() method (which is
good). This stops the test code from being a bad example of abusing the
device model.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Frank Rowand <frank.rowand@sonymobile.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Fix bugs pointed out by checkpatch: Mis-coding of two if statements
caused early return from function.
Number of tests completed increased from 102 to 107.
Number of tests failed increased from 0 to 2.
Signed-off-by: Frank Rowand <frank.rowand@sonymobile.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Fix warnings pointed out by checkpatch.
Checkpatch warns: externs should be avoided in .c files
Reducing pain for future maintainers - adding a comment so that anyone trying
to find where the extern data is created will be able to find it.
(grep will not find that location)
Signed-off-by: Frank Rowand <frank.rowand@sonymobile.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Fix warnings pointed out by checkpatch.
No bug fixes, but reduce the number of checkpatch warnings so that future
problems will stand out better.
Signed-off-by: Frank Rowand <frank.rowand@sonymobile.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Fix bug pointed out by checkpatch.
Splitting string incorrectly removed a space between two words.
Signed-off-by: Frank Rowand <frank.rowand@sonymobile.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Fix warnings pointed out by checkpatch.
No bugs fixed, but the test code should be a good example of how to use
the devicetree API.
Signed-off-by: Frank Rowand <frank.rowand@sonymobile.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
of_get_mac_address() basically does the same thing thrice, every time with a
different property name, so it makes sense to factor out the repetitive code
into separate function. While at it, we can start using ETH_ALEN instead of the
bare number and drop unnecessary parens around the property length check.
The resulting ARM object file is 100 bytes less in size than before the patch.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The "sdc" node is missing the ranges property, it needs to be treated
as having an empty one otherwise translation fails for its children.
Fixes 746c9e9f92, "of/base: Fix PowerPC address parsing hack"
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Stable <stable@vger.kernel.org> # v3.18+
Currently OF_DYNAMIC and OF_OVERLAY are not visible to the user, and are
selected automatically only when needed.
Allow them to be enabled manually to improve device tree unit test
coverage.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The "sdc" node is missing the ranges property, it needs to be treated
as having an empty one otherwise translation fails for its children.
Fixes 746c9e9f92, "of/base: Fix PowerPC address parsing hack"
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Stable <stable@vger.kernel.org> # v3.18+
This patch just replace the string 'selftest' with 'unittest'
in OF unittest and data and binding file.
I have tested it successfully on ARM.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
If CONFIG_OF_UNITTEST=y then a kernel image make will always cause .version to
be incremented, even if there are not source changes. This is caused by
a lack of dependency tracking and checking for
drivers/of/unittest-data/testcases.dtb.o.
Signed-off-by: Frank Rowand <frank.rowand@sonymobile.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This series converts of_graph_get_next_endpoint to decrement the refcount of
the passed prev parameter. This allows to add a for_each_endpoint_of_node
helper macro to loop over all endpoints in a device tree node.
The of_graph_get_port_by_id function is added to retrieve a port by its known
port id (contained in the reg property) from the device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jtB3
-----END PGP SIGNATURE-----
Merge tag 'of-graph-for-4.0' of git://git.pengutronix.de/git/pza/linux into for-next
Pull of-graph helpers from Philipp Zabel:
of: Add of-graph helpers to loop over endpoints and find ports by id
This series converts of_graph_get_next_endpoint to decrement the refcount of
the passed prev parameter. This allows to add a for_each_endpoint_of_node
helper macro to loop over all endpoints in a device tree node.
The of_graph_get_port_by_id function is added to retrieve a port by its known
port id (contained in the reg property) from the device tree.
Conflicts:
net/netfilter/nf_tables_core.c
The nf_tables_core.c conflict was resolved using a conflict resolution
from Stephen Rothwell as a guide.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
* pci/iommu:
of: Calculate device DMA masks based on DT dma-range size
arm: dma-mapping: limit IOMMU mapping size
PCI: Update DMA configuration from DT
of/pci: Add of_pci_dma_configure() to update DMA configuration
PCI: Add helper functions pci_get[put]_host_bridge_device()
of: Fix size when dma-range is not used
of: Move of_dma_configure() to device.c to help re-use
of: iommu: Add ptr to OF node arg to of_iommu_configure()
* pci/resource:
PCI: Fail pci_ioremap_bar() on unassigned resources
PCI: Show driver, BAR#, and resource on pci_ioremap_bar() failure
PCI: Mark invalid BARs as unassigned
PNP: Don't check for overlaps with unassigned PCI BARs
This reverts commit 2fa645cb27.
The assumption that at least 1 preferred console will be registered
when the stdout-path property is set is invalid, which can result
in _no_ consoles.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Commit 106937e8cc ("of: fix handling of '/' in options for
of_find_node_by_path()") caused a regression in OF handling of
stdout-path. While it fixes some cases which have '/' after the ':', it
breaks cases where there is more than one '/' *before* the ':'.
For example, it breaks this boot string
stdout-path = "/rdb/serial@f040ab00:115200";
So rather than doing sequentialized checks (first for '/', then for ':';
or vice versa), to get the correct behavior we need to check for the
first occurrence of either one of them.
It so happens that the handy strcspn() helper can do just that.
Fixes: 106937e8cc ("of: fix handling of '/' in options for of_find_node_by_path()")
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: stable@vger.kernel.org # 3.19
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
There were regressions seen with commit 106937e8cc ("of: fix handling
of '/' in options for of_find_node_by_path()"), where we couldn't handle
extra '/' before the ':'. Let's test for this now.
Confirmed that this test fails without the previous patch and passes
when patched. All other tests pass.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The error code paths that require cleanup use a goto to jump to the
cleanup code and return an error code. However, the error code variable
res, which is initialized to -EINVAL when declared, is then overwritten
with the return value of of_parse_phandle_with_args(), and reused as the
return code from of_irq_parse_one(). This leads to an undetermined error
being returned instead of the expected -EINVAL value. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Cc: stable@vger.kernel.org # 3.13+
Signed-off-by: Rob Herring <robh@kernel.org>
I2C supports adding adapters using either a dynamic or fixed id. The
latter is provided by aliases in the DT case. To prevent id collisions
of those two types, install this function which gives us the highest
fixed id, so we can then let the dynamically created ones come after
this highest number.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Calculate the dma_mask and coherent_dma_mask based on the dma-range values
set in DT for the device.
Limit the mask to lower of the default mask and mask calculated.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Will Deacon <will.deacon@arm.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Export of_mdio_parse_addr() which allows parsing a given Ethernet PHY
node MDIO address, verify it is within the allowed range, and return
its value. This is going to be useful for the DSA code which needs to
deal with multiple layers of MDIO buses.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add testcase variants with '/' in the options string to test for
scan beyond end path name terminated by ':'.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Ensure proper handling of paths with appended options (after ':'),
where those options may contain a '/'.
Fixes: 7914a7c565 ("of: support passing console options with stdout-path")
Reported-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Cc: <stable@vger.kernel.org> # 3.19
Signed-off-by: Rob Herring <robh@kernel.org>
This patch fix the wrong expected value of of_property_match_string
in of_selftest_property_string.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Remove the duplicate of_changeset_init. In of_selftest_changeset
testcase, the "struct of_changeset chgset" is initialized twice,
but only once is enough. so, drop the first initializtion code.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The unittest fails to link if I2C or I2C_MUX is a loadable module:
drivers/built-in.o: In function `selftest_i2c_mux_remove':
unittest.c:(.text+0xb0ce4): undefined reference to `i2c_del_mux_adapter'
This changes the newly added IS_ENABLED() checks to use IS_BUILTIN()
instead, which evaluates to false if the other driver is a module.
Reported-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d5e75500ca ("of: unitest: Add I2C overlay unit tests.")
Signed-off-by: Rob Herring <robh@kernel.org>
Commit 3e7f7626fd ("of/overlay: Do not generate duplicate nodes") removed
the only use of the 'grandchild' variable, which leads to the following build
warning:
drivers/of/overlay.c: In function 'of_overlay_apply_single_device_node':
drivers/of/overlay.c:89:31: warning: unused variable 'grandchild' [-Wunused-variable]
struct device_node *tchild, *grandchild;
^
Remove this unused variable.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Support for devicetree serial consoles via 'stdout-path' causes
bootconsoles to be disabled when the vt dummy console loads, since
there is no preferred console (the preferred console is not added
until the device is probed).
Ensure there is at least a preferred console, even if never matched.
Requires: "console: Fix console name size mismatch"
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add of_pci_dma_configure() to allow updating the DMA configuration of the
PCI device using the configuration from DT of the parent of the root bridge
device. Use the newly added APIs pci_get/put_host_bridge_device() for
implementing this.
[bhelgaas: fold in fix for host bridges with no parent OF device]
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> (AMD Seattle)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
Fix the dma-range size when the DT attribute is missing, i.e., set size to
dev->coherent_dma_mask + 1 instead of dev->coherent_dma_mask. Also add
code to check invalid values of size configured in DT and log error.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> (AMD Seattle)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
Move of_dma_configure() to device.c so it can be re-used for PCI devices to
obtain DMA configuration from DT. Also add a second argument so that for
PCI, the DT node of root bus host bridge can be used to obtain the DMA
configuration for the slave PCI device.
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> (AMD Seattle)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
of_iommu_configure() is called from of_dma_configure() to setup iommu ops
using DT property. This API is currently used for platform devices for
which DMA configuration (including IOMMU ops) may come from the device's
parent. To extend this functionality for PCI devices, this API needs to
take a parent node ptr as an argument instead of assuming device's parent.
This is needed since for PCI, the DMA configuration may be defined in the
DT node of the root bus bridge's parent device. Currently only dma-range
is used for PCI and IOMMU is not supported. Return error if the device is
PCI.
Add "parent" parameter (a struct device_node *) to of_iommu_configure().
Tested-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com> (AMD Seattle)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
CC: Joerg Roedel <joro@8bytes.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
CC: Arnd Bergmann <arnd@arndb.de>
The overlay code uses IDRs but does not explicitly include the header
providing the interface, instead relying on an implicit inclusion. Make
the dependency explicit to avoid potential future build issues if the
implicit inclusion goes away.
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The whole menu already depends on OF, so there is no need to additionaly specify it.
Suggested-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Rob Herring <robh@kernel.org>
This patch adds a function to get a port device tree node by port id,
or reg property value.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Decrementing the reference count of the previous endpoint node allows to
use the of_graph_get_next_endpoint function in a for_each_... style macro.
All current users of this function that pass a non-NULL prev parameter
(that is, soc_camera and imx-drm) are changed to not decrement the passed
prev argument's refcount themselves.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
- DT unittests for I2C probing and overlays from Pantelis Antoniou
- Remove DT unittest dependency on OF_DYNAMIC from Gaurav Minocha
- Add Tegra compatible strings missing for newer parts from Paul
Walmsley
- Various vendor prefix additions
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU3CJVAAoJEMhvYp4jgsXieMgIAKlpr8gcMq/ORRRbVJ9jrL64
A0gPZZEBBVJ0BX7b6mvz15/6Zt70naoE23tMgaCQpR620ox9xFshmwhzHct9npiQ
KRode+9QhFRvA3Pc5LXhfD+bnyJ3Z4pWPrbY6sDDL9txqolpUhU4fz8Y3InwN5YB
GSD6NG3UKDmrTOvkR1j2WrCIkSeXYAEKtnuQlN/+eZXM6kzZYDcdskHv6o18mf4b
Ys6mwkfJdN3UZVQE8ZxUSi3wdC9U7mErNOZuc2rgL9Qb+q0RHtgE2GTI2Zxw0Sj1
BlCO1Fs0sYhOunZIazLJht7cenGbBMf+ed2DB4VLNiEmPhavqdv9wjNt9jOjh5k=
=Aviy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree changes from Rob Herring:
- DT unittests for I2C probing and overlays from Pantelis Antoniou
- Remove DT unittest dependency on OF_DYNAMIC from Gaurav Minocha
- Add Tegra compatible strings missing for newer parts from Paul
Walmsley
- Various vendor prefix additions
* tag 'devicetree-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: Add vendor prefix for OmniVision Technologies
of: Use ovti for Omnivision
of: Add vendor prefix for Truly Semiconductors Limited
of: Add vendor prefix for Himax Technologies Inc.
of/fdt: fix sparse warning
of: unitest: Add I2C overlay unit tests.
Documentation: DT: document compatible string existence requirement
Documentation: DT bindings: add nvidia, tegra132-denver compatible string
Documentation: DT bindings: add more Tegra chip compatible strings
of: EXPORT_SYMBOL_GPL of_property_read_u64_array
of: Fix brace position for struct of_device_id definition
of/unittest: Remove obsolete code
dt-bindings: use isil prefix for Intersil in vendor-prefixes.txt
Add AD Holdings Plc. to vendor-prefixes.
dt-bindings: Add Silicon Mitus vendor prefix
Removes OF_UNITTEST dependency on OF_DYNAMIC config symbol
pinctrl: fix up device tree bindings
DT: Vendors: Add Everspin
doc: add bindings document for altera fpga manager
drivers: of: Export of_reserved_mem_device_{init,release}
Commit d2be00c0fb ("of/pci: Free resources on failure in
of_pci_get_host_bridge_resources()") fixed the error path so it frees
everything on the "resources" list. That list includes the bus_range, so
we should not free it again.
Remove the superfluous free of bus_range.
[bhelgaas: changelog]
Fixes: d2be00c0fb ("of/pci: Free resources on failure in of_pci_get_host_bridge_resources()")
Reported-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Rafael J. Wysocki <rjw@rjwysocki.net>
- Rework of the core ACPI resources parsing code to fix issues
in it and make using resource offsets more convenient and
consolidation of some resource-handing code in a couple of places
that have grown analagous data structures and code to cover the
the same gap in the core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus,
Jarkko Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states
to make the code more straightforward and less bloated overall
(Rafael J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki,
Yaowei Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in
the right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist,
Pavel Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=zZER
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"We have a few new features this time, including a new SFI-based
cpufreq driver, a new devfreq driver for Tegra Activity Monitor, a new
devfreq class for providing its governors with raw utilization data
and a new ACPI driver for AMD SoCs.
Still, the majority of changes here are reworks of existing code to
make it more straightforward or to prepare it for implementing new
features on top of it. The primary example is the rework of ACPI
resources handling from Jiang Liu, Thomas Gleixner and Lv Zheng with
support for IOAPIC hotplug implemented on top of it, but there is
quite a number of changes of this kind in the cpufreq core, ACPICA,
ACPI EC driver, ACPI processor driver and the generic power domains
core code too.
The most active developer is Viresh Kumar with his cpufreq changes.
Specifics:
- Rework of the core ACPI resources parsing code to fix issues in it
and make using resource offsets more convenient and consolidation
of some resource-handing code in a couple of places that have grown
analagous data structures and code to cover the the same gap in the
core (Jiang Liu, Thomas Gleixner, Lv Zheng).
- ACPI-based IOAPIC hotplug support on top of the resources handling
rework (Jiang Liu, Yinghai Lu).
- ACPICA update to upstream release 20150204 including an interrupt
handling rework that allows drivers to install raw handlers for
ACPI GPEs which then become entirely responsible for the given GPE
and the ACPICA core code won't touch it (Lv Zheng, David E Box,
Octavian Purdila).
- ACPI EC driver rework to fix several concurrency issues and other
problems related to events handling on top of the ACPICA's new
support for raw GPE handlers (Lv Zheng).
- New ACPI driver for AMD SoCs analogous to the LPSS (Low-Power
Subsystem) driver for Intel chips (Ken Xue).
- Two minor fixes of the ACPI LPSS driver (Heikki Krogerus, Jarkko
Nikula).
- Two new blacklist entries for machines (Samsung 730U3E/740U3E and
510R) where the native backlight interface doesn't work correctly
while the ACPI one does (Hans de Goede).
- Rework of the ACPI processor driver's handling of idle states to
make the code more straightforward and less bloated overall (Rafael
J Wysocki).
- Assorted minor fixes related to ACPI and SFI (Andreas Ruprecht,
Andy Shevchenko, Hanjun Guo, Jan Beulich, Rafael J Wysocki, Yaowei
Bai).
- PCI core power management modification to avoid resuming (some)
runtime-suspended devices during system suspend if they are in the
right states already (Rafael J Wysocki).
- New SFI-based cpufreq driver for Intel platforms using SFI
(Srinidhi Kasagar).
- cpufreq core fixes, cleanups and simplifications (Viresh Kumar,
Doug Anderson, Wolfram Sang).
- SkyLake CPU support and other updates for the intel_pstate driver
(Kristen Carlson Accardi, Srinivas Pandruvada).
- cpufreq-dt driver cleanup (Markus Elfring).
- Init fix for the ARM big.LITTLE cpuidle driver (Sudeep Holla).
- Generic power domains core code fixes and cleanups (Ulf Hansson).
- Operating Performance Points (OPP) core code cleanups and kernel
documentation update (Nishanth Menon).
- New dabugfs interface to make the list of PM QoS constraints
available to user space (Nishanth Menon).
- New devfreq driver for Tegra Activity Monitor (Tomeu Vizoso).
- New devfreq class (devfreq_event) to provide raw utilization data
to devfreq governors (Chanwoo Choi).
- Assorted minor fixes and cleanups related to power management
(Andreas Ruprecht, Krzysztof Kozlowski, Rickard Strandqvist, Pavel
Machek, Todd E Brandt, Wonhong Kwon).
- turbostat updates (Len Brown) and cpupower Makefile improvement
(Sriram Raghunathan)"
* tag 'pm+acpi-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (151 commits)
tools/power turbostat: relax dependency on APERF_MSR
tools/power turbostat: relax dependency on invariant TSC
Merge branch 'pci/host-generic' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into acpi-resources
tools/power turbostat: decode MSR_*_PERF_LIMIT_REASONS
tools/power turbostat: relax dependency on root permission
ACPI / video: Add disable_native_backlight quirk for Samsung 510R
ACPI / PM: Remove unneeded nested #ifdef
USB / PM: Remove unneeded #ifdef and associated dead code
intel_pstate: provide option to only use intel_pstate with HWP
ACPI / EC: Add GPE reference counting debugging messages
ACPI / EC: Add query flushing support
ACPI / EC: Refine command storm prevention support
ACPI / EC: Add command flushing support.
ACPI / EC: Introduce STARTED/STOPPED flags to replace BLOCKED flag
ACPI: add AMD ACPI2Platform device support for x86 system
ACPI / table: remove duplicate NULL check for the handler of acpi_table_parse()
ACPI / EC: Update revision due to raw handler mode.
ACPI / EC: Reduce ec_poll() by referencing the last register access timestamp.
ACPI / EC: Fix several GPE handling issues by deploying ACPI_GPE_DISPATCH_RAW_HANDLER mode.
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
...
modified: drivers/of/of_pci.c
This fixes a build failure after merging the 'acpi-resources' branch
with the PCI tree caused by bad interactions between that branch and
the only commit in 'pci/host-generic'. Also that commit contains a
bug which can be fixed by removing one line of code, so do that too.
Link: http://marc.info/?l=linux-kernel&m=142344882101429&w=2
Link: http://marc.info/?l=linux-next&m=142346304003932&w=2
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
this patch fixes following sparse warning:
fdt.c:765:12: warning: symbol 'early_init_dt_scan_chosen_serial' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Introduce I2C device tree overlay tests.
Tests insertion and removal of i2c adapters, i2c devices, and muxes.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Make of_property_read_u64_array() available for modules as well. This was
missing from the patch which originally added the function.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Rob Herring <robh@kernel.org>
In the function of_pci_get_host_bridge_resources() if the parsing of ranges
fails, previously allocated resources inclusive of bus_range are not freed
and are not expected to be freed by the function caller on error return.
This patch fixes the issues by adding code that properly frees resources
and bus_range before exiting the function with an error return value.
Fixes: cbe4097f8a ("of/pci: Add support for parsing PCI host bridge resources from DT")
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Rob Herring <robh+dt@kernel.org>
Introduce selftests for overlays using sub-devices present
in children nodes.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Commit 3ce04b4a9, "Removes OF_UNITTEST dependency on OF_DYNAMIC config
symbol" removes a bunch of code, but missed a few minor bits. Clean it
up by removing the node removal cache and flag.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: Rob Herring <robh@kernel.org>
When using overlays with drivers calling of_populate the notifier
will try to create the device twice. Using the populated bit
before proceeding protects against this.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
During the course of the rewrites a bug sneaked in when dealing
with children nodes of overlays, which ends up duplicating
sub nodes.
Simply remove the duplicate traversal of child nodes to fix.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Now that we can create and attach to IOMMU domains via of_dma_configure,
make sure we give the architecture a chance to tear them down when a
platform or amba device is destroyed.
Acked-by: Rob Herring <robh@kernel.org>
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch intends to remove the unittests dependency on
the functions defined in dynamic.c. So, rather than calling
of_attach_node defined in dynamic.c, minimal functionality
required to attach a new node is re-defined in unittest.c.
Also, now after executing the tests the test data is not
removed from the device tree so there is no need to call
of_detach_node.
Tested with and without OF_DYNAMIC enabled on ppc, arm and
x86
Signed-off-by: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Export of_reserved_mem_device_{init,release} so that modules
can initialize and release their assigned per-device cma_area.
Signed-off-by: George G. Davis <george_davis@mentor.com>
[robh: s/EXPORT_SYMBOL/EXPORT_SYMBOL_GPL/]
Signed-off-by: Rob Herring <robh@kernel.org>
fix the dev_dbg to display the offset which is the calculated
dma_pfn_offset value and set later in the code.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The iomm-config branch contains work from Will Deacon, quoting his description:
This series adds automatic IOMMU and DMA-mapping configuration for
OF-based DMA masters described using the generic IOMMU devicetree
bindings. Although there is plenty of future work around splitting up
iommu_ops, adding default IOMMU domains and sorting out automatic IOMMU
group creation for the platform_bus, this is already useful enough for
people to port over their IOMMU drivers and start using the new probing
infrastructure (indeed, Marek has patches queued for the Exynos IOMMU).
The branch touches core ARM and IOMMU driver files, and the respective
maintainers (Russell King and Joerg Roedel) agreed to have the contents
merged through the arm-soc tree. The final version was ready just before
the merge window, so we ended up delaying it a bit longer than the rest,
but we don't expect to see regressions because this is just additional
infrastructure that will get used in drivers starting in 3.20 but is
unused so far.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=ELLq
-----END PGP SIGNATURE-----
Merge tag 'iommu-config-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC/iommu configuration update from Arnd Bergmann:
"The iomm-config branch contains work from Will Deacon, quoting his
description:
This series adds automatic IOMMU and DMA-mapping configuration for
OF-based DMA masters described using the generic IOMMU devicetree
bindings. Although there is plenty of future work around splitting up
iommu_ops, adding default IOMMU domains and sorting out automatic IOMMU
group creation for the platform_bus, this is already useful enough for
people to port over their IOMMU drivers and start using the new probing
infrastructure (indeed, Marek has patches queued for the Exynos IOMMU).
The branch touches core ARM and IOMMU driver files, and the respective
maintainers (Russell King and Joerg Roedel) agreed to have the
contents merged through the arm-soc tree.
The final version was ready just before the merge window, so we ended
up delaying it a bit longer than the rest, but we don't expect to see
regressions because this is just additional infrastructure that will
get used in drivers starting in 3.20 but is unused so far"
* tag 'iommu-config-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
iommu: store DT-probed IOMMU data privately
arm: dma-mapping: plumb our iommu mapping ops into arch_setup_dma_ops
arm: call iommu_init before of_platform_populate
dma-mapping: detect and configure IOMMU in of_dma_configure
iommu: fix initialization without 'add_device' callback
iommu: provide helper function to configure an IOMMU for an of master
iommu: add new iommu_ops callback for adding an OF device
dma-mapping: replace set_arch_dma_coherent_ops with arch_setup_dma_ops
iommu: provide early initialisation hook for IOMMU drivers
Pull i2c updates from Wolfram Sang:
"For 3.19, the I2C subsystem has to offer special candy this time.
Right in time for Christmas :)
- I2C slave framework: finally, a generic mechanism for Linux being
an I2C slave (if the bus driver supports that). Docs are still
missing but will come later this cycle, the code is good enough to
go.
- I2C muxes represent their topology in sysfs much more detailed.
This will help users to navigate around much easier.
- irq population of i2c clients is now done at probe time, not device
creation time, to have better support for deferred probing.
- new drivers for Imagination SCB, Amlogic Meson
- DMA support added for Freescale IMX, Renesas SHMobile
- slightly bigger driver updates to OMAP, i801, AT91, and rk3x
(mostly quirk handling, timing updates, and using better kernel
interfaces)
- eeprom driver can now write with byte-access (very slow, but OK to
have)
- and the bunch of smaller fixes, cleanups, ID updates..."
* 'i2c/for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (56 commits)
i2c: sh_mobile: remove unneeded DMA mask
i2c: rcar: add slave support
i2c: slave-eeprom: add eeprom simulator driver
i2c: core changes for slave support
MAINTAINERS: add I2C dt bindings also to I2C realm
i2c: designware: Fix falling time bindings doc
i2c: davinci: switch to use platform_get_irq
Documentation: i2c: Use PM ops instead of legacy suspend/resume
i2c: sh_mobile: optimize irq entry
i2c: pxa: add support for SCCB devices
omap: i2c: don't check bus state IP rev3.3 and earlier
i2c: s3c2410: Handle i2c sys_cfg register in i2c driver
i2c: rk3x: add Kconfig dependency on COMMON_CLK
i2c: omap: add notes related to i2c multimaster mode
i2c: omap: don't reset controller if Arbitration Lost detected
i2c: omap: implement workaround for handling invalid BB-bit values
i2c: omap: cleanup register definitions
i2c: rk3x: handle dynamic clock rate changes correctly
i2c: at91: enable probe deferring on dma channel request
i2c: at91: remove legacy DMA support
...
Lots of activity in the devicetree code for v3.18. Most of it is related
to getting all of the overlay support code in place, but there are other
important things in there.
There are a few trivial merge conflicts. They shouldn't give you any
trouble.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device tree
- Removal of the of_allnodes list. This used to be used to iterate over
all the nodes in the device tree, but it is unnecessary because the
same thing can be done by iterating over the list of child pointers.
Getting rid of of_allnodes saves some memory and avoids the
possibility of of_allnodes being sorted differently from the child
lists.
- Support for retrieving original DTB blob via sysfs. Needed by kexec.
- More unittests
- Documentation and minor bug fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ak0A
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Lots of activity in the devicetree code for v3.18. Most of it is
related to getting all of the overlay support code in place, but there
are other important things in there.
Highlights:
- OF_RECONFIG notifiers for SPI, I2C and Platform devices. Those
subsystems can now respond to live changes to the device tree.
- CONFIG_OF_OVERLAY method for applying live changes to the device
tree
- Removal of the of_allnodes list. This used to be used to iterate
over all the nodes in the device tree, but it is unnecessary
because the same thing can be done by iterating over the list of
child pointers. Getting rid of of_allnodes saves some memory and
avoids the possibility of of_allnodes being sorted differently from
the child lists.
- Support for retrieving original DTB blob via sysfs. Needed by
kexec.
- More unittests
- Documentation and minor bug fixes"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux: (42 commits)
of: Delete unnecessary check before calling "of_node_put()"
of: Drop ->next pointer from struct device_node
spi: Check for spi_of_notifier when CONFIG_OF_DYNAMIC=y
of: support passing console options with stdout-path
of: add optional options parameter to of_find_node_by_path()
of: Add bindings for chosen node, stdout-path
of: Remove unneeded and incorrect MODULE_DEVICE_TABLE
ARM: dt: fix up PL011 device tree bindings
of: base, fix of_property_read_string_helper kernel-doc
of: remove select of non-existant OF_DEVICE config symbol
spi/of: Add OF notifier handler
spi/of: Create new device registration method and accessors
i2c/of: Add OF_RECONFIG notifier handler
i2c/of: Factor out Devicetree registration code
of/overlay: Add overlay unittests
of/overlay: Introduce DT overlay support
of/reconfig: Add OF_DYNAMIC notifier for platform_bus_type
of/reconfig: Always use the same structure for notifiers
of/reconfig: Add debug output for OF_RECONFIG notifiers
of/reconfig: Add empty stubs for the of_reconfig methods
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
Pull irq domain updates from Thomas Gleixner:
"The real interesting irq updates:
- Support for hierarchical irq domains:
For complex interrupt routing scenarios where more than one
interrupt related chip is involved we had no proper representation
in the generic interrupt infrastructure so far. That made people
implement rather ugly constructs in their nested irq chip
implementations. The main offenders are x86 and arm/gic.
To distangle that mess we have now hierarchical irqdomains which
seperate the various interrupt chips and connect them via the
hierarchical domains. That keeps the domain specific details
internal to the particular hierarchy level and removes the
criss/cross referencing of chip internals. The resulting hierarchy
for a complex x86 system will look like this:
vector mapped: 74
msi-0 mapped: 2
dmar-ir-1 mapped: 69
ioapic-1 mapped: 4
ioapic-0 mapped: 20
pci-msi-2 mapped: 45
dmar-ir-0 mapped: 3
ioapic-2 mapped: 1
pci-msi-1 mapped: 2
htirq mapped: 0
Neither ioapic nor pci-msi know about the dmar interrupt remapping
between themself and the vector domain. If interrupt remapping is
disabled ioapic and pci-msi become direct childs of the vector
domain.
In hindsight we should have done that years ago, but in hindsight
we always know better :)
- Support for generic MSI interrupt domain handling
We have more and more non PCI related MSI interrupts, so providing
a generic infrastructure for this is better than having all
affected architectures implementing their own private hacks.
- Support for PCI-MSI interrupt domain handling, based on the generic
MSI support.
This part carries the pci/msi branch from Bjorn Helgaas pci tree to
avoid a massive conflict. The PCI/MSI parts are acked by Bjorn.
I have two more branches on top of this. The full conversion of x86
to hierarchical domains and a partial conversion of arm/gic"
* 'irq-irqdomain-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
genirq: Move irq_chip_write_msi_msg() helper to core
PCI/MSI: Allow an msi_controller to be associated to an irq domain
PCI/MSI: Provide mechanism to alloc/free MSI/MSIX interrupt from irqdomain
PCI/MSI: Enhance core to support hierarchy irqdomain
PCI/MSI: Move cached entry functions to irq core
genirq: Provide default callbacks for msi_domain_ops
genirq: Introduce msi_domain_alloc/free_irqs()
asm-generic: Add msi.h
genirq: Add generic msi irq domain support
genirq: Introduce callback irq_chip.irq_write_msi_msg
genirq: Work around __irq_set_handler vs stacked domains ordering issues
irqdomain: Introduce helper function irq_domain_add_hierarchy()
irqdomain: Implement a method to automatically call parent domains alloc/free
genirq: Introduce helper irq_domain_set_info() to reduce duplicated code
genirq: Split out flow handler typedefs into seperate header file
genirq: Add IRQ_SET_MASK_OK_DONE to support stacked irqchip
genirq: Introduce irq_chip.irq_compose_msi_msg() to support stacked irqchip
genirq: Add more helper functions to support stacked irq_chip
genirq: Introduce helper functions to support stacked irq_chip
irqdomain: Do irq_find_mapping and set_type for hierarchy irqdomain in case OF
...
* device-properties:
leds: leds-gpio: Fix multiple instances registration without 'label' property
leds: leds-gpio: Fix legacy GPIO number case
ACPI / property: Drop size_prop from acpi_dev_get_property_reference()
leds: leds-gpio: Convert gpio_blink_set() to use GPIO descriptors
ACPI / GPIO: Document ACPI GPIO mappings API
net: rfkill: gpio: Add default GPIO driver mappings for ACPI
ACPI / GPIO: Driver GPIO mappings for ACPI GPIOs
input: gpio_keys_polled: Make use of device property API
leds: leds-gpio: Make use of device property API
gpio: Support for unified device properties interface
Driver core: Unified interface for firmware node properties
input: gpio_keys_polled: Add support for GPIO descriptors
leds: leds-gpio: Add support for GPIO descriptors
gpio: sch: Consolidate core and resume banks
gpio / ACPI: Add support for _DSD device properties
misc: at25: Make use of device property API
ACPI: Allow drivers to match using Device Tree compatible property
Driver core: Unified device properties interface for platform firmware
ACPI: Add support for device specific properties
The of_node_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The ->next pointer in struct device_node is a hanger-on from when it was
used to iterate over the whole tree by a particular device_type property
value. Those days are long over, but the fdt unflattening code still
uses it to put nodes in the unflattened tree into the same order as node
in the flat tree. By reworking the unflattening code to reverse the list
after unflattening all the children of a node, the pointer can be
dropped which gives a small amount of memory savings.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Frank Rowand <frank.rowand@sonymobile.com>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Support specifying console options (like with console=ttyXN,<options>)
by appending them to the stdout-path property after a separating ':'.
Example:
stdout-path = "uart0:115200";
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
[grant.likely: minor rework to shorten the diffstat]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Update of_find_node_by_path():
1) Rename function to of_find_node_opts_by_path(), adding an optional
pointer argument. Provide a static inline wrapper version of
of_find_node_by_path() which calls the new function with NULL as
the optional argument.
2) Ignore any part of the path beyond and including the ':' separator.
3) Set the new provided pointer argument to the beginning of the string
following the ':' separator.
4: Add tests.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch extends of_dma_configure so that it sets up the IOMMU for a
device, as well as the coherent/non-coherent DMA mapping ops.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
set_arch_dma_coherent_ops is called from of_dma_configure in order to
swizzle the architectural dma-mapping functions over to a cache-coherent
implementation. This is currently implemented only for ARM.
In anticipation of re-using this mechanism for IOMMU-backed dma-mapping
ops too, this patch replaces the function with a broader
arch_setup_dma_ops callback which will be extended in future.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The unittest code has a MODULE_DEVICE_TABLE that isn't needed by any of
the unittests, and isn't even correct. Remove it.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
It referenced of_property_read_string_util whereas the function name
is of_property_read_string_helper.
Introduced in a87fa1d81a (of: Fix
overflow bug in string property parsing functions). Found out when
reviewing the stable 3.12 queue.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The OF_OVERLAY option selects OF_DEVICE, but OF_DEVICE was removed in
commit ba166e900b, "of: remove CONFIG_OF_DEVICE". Remove the unnecessary
select.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
memblock_is_region_reserved() returns true in the case of a partial
overlap, meaning that the current code fails to reserve the
non-overlapping portion.
This call was introduced as part of d1552ce449 "of/fdt: move
memreserve and dtb memory reservations into core" which went into
v3.16.
I observed this causing a Midway system with a buggy fdt (the header
declares itself to be larger than it really is) failing to boot
because the over-inflated size of the fdt was causing it to seem to
run into the swapper_pg_dir region, meaning the DT wasn't reserved.
The symptoms were failing to find an disks or network and failing to
boot.
However given the ambiguity of whether things like the initrd are
covered by /memreserve/ and similar I think it is best to also
register the region rather than just ignoring it.
Since memblock_reserve() handles overlaps just fine lets just warn and
carry on.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: stable@vger.kernel.org # v3.16+
Add unittests for OF overlays.
It tests overlay device addition/removal and whether
the apply revert sequence is correct.
Changes since V1:
* Added local fixups entries.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Overlays are a method to dynamically modify part of the kernel's
device tree with dynamically loaded data. Add the core functionality to
parse, apply and remove an overlay changeset. The core functionality
takes care of managing the overlay data format and performing the add
and remove. Drivers are expected to use the overlay functionality to
support custom expansion busses commonly found on consumer development
boards like the BeagleBone or Raspberry Pi.
The overlay code uses CONFIG_OF_DYNAMIC changesets to perform the low
level work of modifying the devicetree.
Documentation about internal and APIs is provided in
Documentation/devicetree/overlay-notes.txt
v2:
- Switch from __of_node_alloc() to __of_node_dup()
- Documentation fixups
- Remove 2-pass processing of properties
- Remove separate ov_lock; just use the DT mutex.
v1:
- Drop delete capability using '-' prefix. The '-' prefixed names
are valid properties and nodes and there is no need for it just yet.
- Do not update special properties - name & phandle ones.
- Change order of node attachment, so that the special property update
works.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Add OF notifier handler needed for creating/destroying platform devices
according to dynamic runtime changes in the DT live tree.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The OF_RECONFIG notifier callback uses a different structure depending
on whether it is a node change or a property change. This is silly, and
not very safe. Rework the code to use the same data structure regardless
of the type of notifier.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: <linuxppc-dev@lists.ozlabs.org>
Add some additional debug output to cover OF_RECONFIG notifier activity.
At the same time, refactor the changeset debug output to use the same
strings as the notifier debug output.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Introduce of_reconfig_get_state_change() which allows an of notifier
to query about device state changes.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The original resolver format is way too cryptic, switch
to using a tree based format that gets rid of repetitions,
is more compact and readable.
At the same time, update the selftests to using the new local fixups
format.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[grant.likely: Squashed in testcase changes and merged similar functions]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Add a node argument to __of_node_alloc() and rename it to
__of_node_dup() so that it can also be used to duplicate a node with
its properties. This is important for the overlay code so that it can
create new nodes without using separate changeset items for every single
property.
At the same time rework the overlay code to use the new function and
drop the extra changeset items.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The overlay code needs to construct a new full_name from the parent name
and the node name, but the current method has to allocate and then free
an temporary string which is wasteful. Fix this problem by using vargs
to pass in a format and arguments into __of_node_alloc().
At the same time remove the allocflags argument to __of_node_alloc().
The only users all use GFP_KERNEL, so there is no need to provide it as
an option. If there is ever a need later it can be added back.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUcmzrAAoJEHm+PkMAQRiGUskH/il9ul71lyyvrA/bRbi0GfUa
2Ej1Q4Fa/SRzLMiWF8Wy/AlYBbl4/uD3a3XEueK4f9dNguTLZF/rwXTlKKzUeiGg
zFObbJg3zfa926PQcEV5mc+h71ZkWmbH5CjF6GfYIlj6kjVa5MXF3lSZz27DoAx3
DjoLKpj1fXQJu1HD7xvUn0r720RgYfic9iKdS69eEYex+Js92WySukogvMG5WAVD
xuwlJcJgm0YpgNr1t1ij4ekE5XR9jjiE4EXbOZYWcOOd+YXAwZpBrKOgxP0gma3w
OGwEvmAbzf/3IsGq3dPFYWQ2nfiLA/Qh7y20E19FLKpPBu5ZuTEgFU8VTxh+k+g=
=rRmA
-----END PGP SIGNATURE-----
Merge tag 'v3.18-rc6' into devicetree/next
v3.18-rc6 contains an important DT bug fix, c1a2086e2d, "of/selftest:
Fix off-by-one error in removal path" which affects testing of the
overlay patch series. Merge it into the devicetree/next staging branch
so that the overlay patches are applied on top of a known working tree.
Linux 3.18-rc6
Conflicts:
drivers/of/address.c
The /aliases node isn't always present in the device tree, but the
unittest code assumes that /aliases is there. Add a check when inserting
the testcase data to see if of_aliases needs to be updated, and undo the
settings when the nodes are removed.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: <stable@vger.kernel.org>
of_platform_populate() takes a subset of the device tree and turns it
into a set of platform_devices. At the same time it sets the
OF_POPULATED_BUS flag in each bus nodes so that of_platform_depopulate()
can undo the operation at a later time. However, it doesn't set the flag
on the root of the population tree which means that dynamic modifications
of the device tree at runtime will not create/destroy devices correctly.
Fix of_platform_populate() to set the OF_POPULATED_BUS flag on the node
it is called with.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Pawel Moll <pawel.moll@arm.com>
The removal path for selftest data has an off by one error that causes
the code to dereference beyond the end of the nodes[] array on the first
pass through. The old code only worked by chance on a lot of platforms,
but the bug was recently exposed on aarch64.
The fix is simple. Decrement the node count before dereferencing, not
after.
Reported-by: Kevin Hilman <khilman@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: <stable@vger.kernel.org> # v3.17+
Create a new /sys entry '/sys/firmware/fdt' to export the FDT blob
that was passed to the kernel by the bootloader. This allows userland
applications such as kexec to access the raw binary.
The fact that this node does not reside under /sys/firmware/device-tree
is deliberate: FDT is also used on arm64 UEFI/ACPI systems to
communicate just the UEFI and ACPI entry points, but the FDT is never
unflattened and used to configure the system.
A CRC32 checksum is calculated over the entire FDT blob, and verified
at late_initcall time. The sysfs entry is instantiated only if the
checksum is valid, i.e., if the FDT blob has not been modified in the
mean time. Otherwise, a warning is printed.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
We have a historical hack that treats missing ranges properties as the
equivalent of an empty one. This is needed for ancient PowerMac "bad"
device-trees, and shouldn't be enabled for any other PowerPC platform,
otherwise we get some nasty layout of devices in sysfs or even
duplication when a set of otherwise identically named devices is
created multiple times under a different parent node with no ranges
property.
This fix is needed for the PowerNV i2c busses to be exposed properly
and will fix a number of other embedded cases.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
__earlycon_of_table_sentinel.compatible is a char[128], not a pointer, so
it will never be NULL. Checking it against NULL causes the match loop to
run past the end of the array, and eventually match a bogus entry, under
the following conditions:
- Kernel command line specifies "earlycon" with no parameters
- DT has a stdout-path pointing to a UART node
- The UART driver doesn't use OF_EARLYCON_DECLARE (or maybe the console
driver is compiled out)
Fix this by checking to see if match->compatible is a non-empty string.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Rob Herring <robh@kernel.org>
This function can only return true or false; using a bool makes it more
obvious to the reader.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This function passes back a value from __of_device_is_compatible(), which
returns a score in the range 0..11, not a bool.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The core always tries to translate any "reg" property to construct the platform
device names. This results in a pile of "OF: no ranges; cannot translate" errors
in dmesg whenever we expose things like i2c devices that cannot directly translate
to the MMIO space.
Turn this into a pr_debug instead
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
"msi_chip" isn't very descriptive, so rename it to "msi_controller". That
tells a little more about what it does and is already used in device tree
bindings.
No functional change.
[bhelgaas: changelog, change *only* the struct name so it's reviewable]
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function will be used by the I2C core which can be compiled as a
module.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add a uniform interface by which device drivers can request device
properties from the platform firmware by providing a property name
and the corresponding data type. The purpose of it is to help to
write portable code that won't depend on any particular platform
firmware interface.
The following general helper functions are added:
device_property_present()
device_property_read_u8()
device_property_read_u16()
device_property_read_u32()
device_property_read_u64()
device_property_read_string()
device_property_read_u8_array()
device_property_read_u16_array()
device_property_read_u32_array()
device_property_read_u64_array()
device_property_read_string_array()
The first one allows the caller to check if the given property is
present. The next 5 of them allow single-valued properties of
various types to be retrieved in a uniform way. The remaining 5 are
for reading properties with multiple values (arrays of either numbers
or strings).
The interface covers both ACPI and Device Trees.
This change set includes material from Mika Westerberg and Aaron Lu.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently the devices created by drivers/of/platform.c get created at
the root of /sys/devices. This goes against the typical pattern for
sysfs where the top level /sys/devices structure contains categories of
devices, and the structure of devices is placed below that. To fix this,
make the code in drivers/of/platform.c follow the drivers/base/platform.c
behaviour, and use &platform_bus as the default parent for all new
platform_devices and amba_devices.
This change has been discussed for a long time, but nobody has actually
acted on it. Userspace code that expects to find devices under a fixed
/sys/devices/... path will be affected. It isn't /supposed/ to do that,
but if anyone complains then I'll add a default-off workaround option to
put them back into the root.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
The device_node pointer in struct of_phandle_args is called "np", not
"node".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Memory regions passed to early_init_dt_add_memory_arch() are rounded to
PAGE_SIZE by subtracting the size of the leading fractional page from
the 'size' argument. However, size being a u64 type, if its value is
sufficiently small, the subtraction wraps around and produces a bogus
value, potentially leading to crashes.
Fix this by ignoring the memory range in such cases.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
If the device tree pointer is NULL, early_init_dt_verify() fails, leaving
initial_boot_params unchanged. If the device tree pointer is non-NULL but
invalid, early_init_dt_verify() again fails but this time it also clears
initial_boot_params.
Leave initial_boot_params unchanged if the device tree pointer is invalid.
This doesn't fix a bug, but it makes the behavior more consistent and
easier to analyze.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch makes the name argument from of_io_request_and_map constant.
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This is unit testing code. It should use that name because it makes more
sense than 'selftest'. Rename the files to match and rename the config
variable.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The of_platform_populate() test cases don't remove the test devices
after they are added. Fix this by adding tests for
of_platform_depopulate().
At the same time rework the selftest() macro to return the test result
value. This makes it easy to use the macro inside an if() condition.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The device tree structure is composed of two lists; the 'allnodes' list
which is a singly linked list containing every node in the tree, and the
child->parent structure where each parent node has a singly linked list
of children. All of the data in the allnodes list can be easily
reproduced with the parent-child lists, so of_allnodes is actually
unnecessary. Remove it entirely which saves a bit of memory and
simplifies the data structure quite a lot.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Cc: Pantelis Antoniou <pantelis@pantelis.antoniou@konsulko.com>
The string property read helpers will run off the end of the buffer if
it is handed a malformed string property. Rework the parsers to make
sure that doesn't happen. At the same time add new test cases to make
sure the functions behave themselves.
The original implementations of of_property_read_string_index() and
of_property_count_strings() both open-coded the same block of parsing
code, each with it's own subtly different bugs. The fix here merges
functions into a single helper and makes the original functions static
inline wrappers around the helper.
One non-bugfix aspect of this patch is the addition of a new wrapper,
of_property_read_string_array(). The new wrapper is needed by the
device_properties feature that Rafael is working on and planning to
merge for v3.19. The implementation is identical both with and without
the new static inline wrapper, so it just got left in to reduce the
churn on the header file.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darren Hart <darren.hart@intel.com>
Cc: <stable@vger.kernel.org> # v3.3+: Drop selftest hunks that don't apply
Driver calling of_reserved_mem_device_init() might be interested if the
initialization has been successful or not, so add support for returning
error code.
This fixes a build warining caused by commit 7bfa5ab6fa ("drivers:
dma-coherent: add initialization from device tree"), which has been
merged without this change and without fixing function return value.
Fixes: 7bfa5ab6fa ("drivers: dma-coherent: add initialization from device tree")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Josh Cartwright <joshc@codeaurora.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This branch contains bug fixes and new features for the devicetree code.
Most of the changes are either new testcases for the selftest code or
documentation changes. The most notable change is the addition of a
phandle resolver for use when grafting in a second device tree blob into
the core tree. The resolver isn't currently used by anything other than
the selftest module, but it will be used to support device tree
overlays; probably in the v3.19 timeframe.
Also note that I've moved my normal tree from git.secretlab.ca to
git.kernel.org.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VYfI
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"This branch contains bug fixes and new features for the devicetree
code.
Most of the changes are either new testcases for the selftest code or
documentation changes. The most notable change is the addition of a
phandle resolver for use when grafting in a second device tree blob
into the core tree. The resolver isn't currently used by anything
other than the selftest module, but it will be used to support device
tree overlays; probably in the v3.19 timeframe.
Also note that I've moved my normal tree from git.secretlab.ca to
git.kernel.org"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/selftest: Move hash table off stack to fix large frame size
To remove non-ascii characters in of_selftest.txt
of/selftest: Use the resolver to fixup phandles
of: Introduce Device Tree resolve support.
of/selftest: Add a test for duplicate phandles
of: Don't try to search when phandle == 0
of/selftest: Test structure of device tree
of: Fix NULL dereference in selftest removal code
of: add vendor prefix for Chipidea
of: Add vendor prefix for Innolux Corporation
of: Add vendor prefix for Sitronix
devicetree: bindings: Document Gateworks vendor prefix
of: Add vendor prefix for Energy Micro
dt/documentation: add specification of dma bus information
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
- eBPF JIT compiler for arm64
- CPU suspend backend for PSCI (firmware interface) with standard idle
states defined in DT (generic idle driver to be merged via a different
tree)
- Support for CONFIG_DEBUG_SET_MODULE_RONX
- Support for unmapped cpu-release-addr (outside kernel linear mapping)
- set_arch_dma_coherent_ops() implemented and bus notifiers removed
- EFI_STUB improvements when base of DRAM is occupied
- Typos in KGDB macros
- Clean-up to (partially) allow kernel building with LLVM
- Other clean-ups (extern keyword, phys_addr_t usage)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=SAfQ
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 updates from Catalin Marinas:
- eBPF JIT compiler for arm64
- CPU suspend backend for PSCI (firmware interface) with standard idle
states defined in DT (generic idle driver to be merged via a
different tree)
- Support for CONFIG_DEBUG_SET_MODULE_RONX
- Support for unmapped cpu-release-addr (outside kernel linear mapping)
- set_arch_dma_coherent_ops() implemented and bus notifiers removed
- EFI_STUB improvements when base of DRAM is occupied
- Typos in KGDB macros
- Clean-up to (partially) allow kernel building with LLVM
- Other clean-ups (extern keyword, phys_addr_t usage)
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (51 commits)
arm64: Remove unneeded extern keyword
ARM64: make of_device_ids const
arm64: Use phys_addr_t type for physical address
aarch64: filter $x from kallsyms
arm64: Use DMA_ERROR_CODE to denote failed allocation
arm64: Fix typos in KGDB macros
arm64: insn: Add return statements after BUG_ON()
arm64: debug: don't re-enable debug exceptions on return from el1_dbg
Revert "arm64: dmi: Add SMBIOS/DMI support"
arm64: Implement set_arch_dma_coherent_ops() to replace bus notifiers
of: amba: use of_dma_configure for AMBA devices
arm64: dmi: Add SMBIOS/DMI support
arm64: Correct ftrace calls to aarch64_insn_gen_branch_imm()
arm64:mm: initialize max_mapnr using function set_max_mapnr
setup: Move unmask of async interrupts after possible earlycon setup
arm64: LLVMLinux: Fix inline arm64 assembly for use with clang
arm64: pageattr: Correctly adjust unaligned start addresses
net: bpf: arm64: fix module memory leak when JIT image build fails
arm64: add PSCI CPU_SUSPEND based cpu_suspend support
arm64: kernel: introduce cpu_init_idle CPU operation
...
Adjust fixed_phy_register() to return struct phy_device *, so that
it becomes easy to use fixed PHYs without device tree support:
phydev = fixed_phy_register(PHY_POLL, &fixed_phy_status, NULL);
fixed_phy_set_link_update(phydev, fixed_phy_link_update);
phy_connect_direct(netdev, phydev, handler_fn, phy_interface);
This change is a prerequisite for modifying bcmgenet driver to work
without a device tree on Broadcom's MIPS-based 7xxx platforms.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new testcase that checks phandle consistency was using a hash table
on the stack which made the frame size much large than it should be. Fix
the problem by moving the hash table into the file scope.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The selftest data ends up causing duplicate phandles in the live tree
for the time that the testcase data is inserted into the live tree. This
is obviously a bad situation because anything attempting to read the
tree while the selftests are running make resolve phandles to one of the
testcase data nodes. Fix the problem by using the of_resolve_phandles()
function to eliminate duplicates.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Introduce support for dynamic device tree resolution.
Using it, it is possible to prepare a device tree that's
been loaded on runtime to be modified and inserted at the kernel
live tree.
Export of of_resolve and bug fix of double free by
Guenter Roeck <groeck@juniper.net>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
[grant.likely: Don't need to select CONFIG_OF_DYNAMIC and CONFIG_OF_DEVICE]
[grant.likely: Don't need to depend on OF or !SPARC]
[grant.likely: Factor out duplicate code blocks into single function]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
All phandles in the tree should be unique. Add a testcase to make sure
that this is so.
Note: this testcase fails on the current kernel because the selftest
code itself ends up adding duplicate phandles. Before this testcase is
merged the selftest code needs to be modified to resolve phandles before
adding them.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
A value of '0' isn't a valid phandle, so searching for a node with that
phandle is pointless. It will result in nothing but false positives.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Add a testcase to verify that the device tree is properly constructed
and the lists are in a correct order. The new testcase gets run twice;
once after adding the testcase data, and once after removing it again.
It is run twice to make sure adding and removing the testcase data
doesn't corrupt the data structure.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The selftest code removes its testcase data from the live tree when
exiting, but if the testcases data tree contains an empty child of the
root, then it causes an oops due to a NULL dereference. The reason is
that the code tries to directly dereference the child pointer without
checking first if a child is actually there.
The solution is to pass the parent node into detach_node_and_children()
instead of trying to pass the child. This required removing the code
that attempts to remove all of the sibling nodes in
detach_node_and_children(), which was never sensible in the first place.
At the same time add a check to make sure the bounds of the nodes list
are not exceeded by the testdata tree. If they are then abort.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
Provide a function to parse the PCI DT ranges that can be used to create a
pci_host_bridge structure together with its associated bus.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
[make io_base parameter optional]
Signed-off-by: Robert Richter <rrichter@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Catalin Marinas <catalin.marinas@arm.com>
Add pci_get_new_domain_nr() to allocate a new domain number and
of_get_pci_domain_nr() to retrieve the PCI domain number of a given device
from DT. Host bridge drivers or architecture-specific code can choose to
implement their PCI domain number policy using these two functions.
Using of_get_pci_domain_nr() guarantees a stable PCI domain number on every
boot provided that all host bridge controllers are assigned a number in the
device tree using "linux,pci-domain" property. Mixing use of
pci_get_new_domain_nr() and of_get_pci_domain_nr() is not recommended as it
can lead to potentially conflicting domain numbers being assigned to root
buses behind different host bridges.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Catalin Marinas <catalin.marinas@arm.com>
The ranges property for a host bridge controller in DT describes the
mapping between the PCI bus address and the CPU physical address. The
resources framework however expects that the IO resources start at a pseudo
"port" address 0 (zero) and have a maximum size of IO_SPACE_LIMIT. The
conversion from PCI ranges to resources failed to take that into account,
returning a CPU physical address instead of a port number.
Also fix all the drivers that depend on the old behaviour by fetching the
CPU physical address based on the port number where it is being needed.
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Simon Horman <horms@verge.net.au>
CC: Catalin Marinas <catalin.marinas@arm.com>
We need to enhance of_pci_range_to_resources() enough that it won't make
sense for it to be inline anymore. Move it to drivers/of/address.c, under
#ifdef CONFIG_PCI.
of_address.h previously implemented of_pci_range_to_resources()
unconditionally, regardless of any config options. The implementation in
address.c is defined only when CONFIG_OF_ADDRESS=y and CONFIG_PCI=y,
so add a dummy version to avoid build errors when CONFIG_OF or
CONFIG_OF_ADDRESS is not defined.
[bhelgaas: drop extra detail from changelog, move def under CONFIG_PCI,
add dummy of_pci_range_to_resource() for build errors (from Arnd)]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Grant Likely <grant.likely@linaro.org>
CC: Rob Herring <robh+dt@kernel.org>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Catalin Marinas <catalin.marinas@arm.com>
Some architectures do not have a simple view of the PCI I/O space and
instead use a range of CPU addresses that map to bus addresses. For some
architectures these ranges will be expressed by OF bindings in a device
tree file.
This patch introduces a pci_register_io_range() helper function with a
generic implementation that can be used by such architectures to keep track
of the I/O ranges described by the PCI bindings. If the PCI_IOBASE macro
is not defined, that signals lack of support for PCI and we return an
error.
In order to retrieve the CPU address associated with an I/O port, a new
helper function pci_pio_to_address() is introduced. This will search in
the list of ranges registered with pci_register_io_range() and return the
CPU address that corresponds to the given port.
[arnd: add dummy !CONFIG_OF pci_pio_to_address() to fix build errors]
Signed-off-by: Liviu Dudau <Liviu.Dudau@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
CC: Grant Likely <grant.likely@linaro.org>
In cases where board has below memory DT node
memory{
device_type = "memory";
reg = <0x80000000 0x80000000>;
};
Check on the memory range in fdt.c will always fail because it is
comparing MAX_PHYS_ADDR with base + size, in fact it should compare
it with base + size - 1.
This issue was originally noticed on Qualcomm IFC6410 board.
Without this patch kernel shows up noticed unnecessary warnings
[ 0.000000] Machine model: Qualcomm APQ8064/IFC6410
[ 0.000000] Ignoring memory range 0xffffffff - 0x100000000
[ 0.000000] cma: Reserved 64 MiB at ab800000
as a result the size get reduced to 0x7fffffff which looks wrong.
This patch fixes the check involved in generating this warning and
as a result it also fixes the wrong size calculation.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[grant.likely: adjust new size calculation also]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
