Don't use Amstrad Delta custom I/O functions any longer, use GPIO API
instead.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Don't use Amstrad Delta custom I/O functions for controlling the device,
use GPIO API instead.
While being at it, add missing gpio_free(AMS_DELTA_GPIO_PIN_NAND_RB).
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Cc: David Woodhouse <dwmw2@infradead.org>
Reviewed-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that the Amstrad Delta on-board latches have been converted to GPIO
devices, use the generic driver to control on-board LEDs which hang off
those latches.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Once ready, ams-delta specific device drivers currently calling custom
ams_delta_latch[12]_write() functions can be updated to call generic
gpio_set_value() instead, which will make them less platform dependent.
Even more, some custom ams-delta only drivers can perhaps be dropped
from the tree after converting selected ams-delta platform devices to
follow generic GPIO based device models.
The latch_gpios[] table is initially filled with all latch1 and latch2
GPIO pins in order to register and initialize them from the board file
until those are handled by respective existing device drivers (leds,
nand, lcd, serio, asoc, serial). That table will get almost empty after
the transision process is completed, holding only pins not used by any
drivers / connected to unused devices, in order to initialize them from
the board file for power saving purposes.
The new ams_delta_latch_write() function is a unified replacement for
those removed ams_delta_latch[12]_write(), and serves as a temporary
wrapper over gpio_set_value(), providing the old API for those not yet
updated device drivers, and will be removed after all custom drivers are
converted or replaced.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We need to detect the SoC revision early, but the SoC
feature detection can be done later on. In order to allow
further clean-up later on, this patch separates the SoC
revision check from the SoC feature check.
This patch doesn't change functionality or behavior of the code
execution; it barely cleans up the code and splits into SoC
specific implementation for Rev ID and feature detection.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:
http://www.spinics.net/lists/linux-omap/msg49561.html
Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).
This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).
Tested on 11MPCore, OMAP4 and Tegra.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
devicetree will become the mandatory boot method for OMAP2+.
In order to avoid cluttering the OMAP code with #ifdef CONFIG_OF,
select USE_OF by default for every OMAP2+ systems.
Enable PROC_DEVICETREE as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An hwmod with a 'HWMOD_INIT_NO_IDLE' flag set, is left in
enabled state by the hwmod framework post the initial setup.
Once a real user of the device (a driver) tries to enable it
at a later point, the hwmod framework throws a WARN() about
the device being already in enabled state.
Fix this by introducing a new internal flag '_HWMOD_SKIP_ENABLE' to
identify such devices/hwmods. When the device/hwmod is requested to be
enabled (the first time) by its driver/user, nothing except the
mux-enable is needed. The mux data is board specific and is
unavailable during initial enable() of the device, done by the
framework as part of setup().
A good example of a such a device is an UART used as debug console.
The UART module needs to be kept enabled through the boot, until the
UART driver takes control of it, for debug prints to appear on
the console.
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: use a flag rather than a state; updated commit message;
edited some documentation]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By default all registered pads will trigger mpu_irqs[0]. Now there is
an API for selecting used mpu_irq on pad basis, which can be used to
trigger different irq handlers for different pads in the same hwmod.
Each pad that requires its interrupt to be re-routed this way must
have a separate call to omap_hwmod_pad_route_irq(hwmod, pad, irq).
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
[paul@pwsan.com: moved fn to omap_hwmod.c; separated fn from mux scan_wakeups
changes; added kerneldoc]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP mux now parses active wakeup events from pad registers and calls
corresponding hwmod ISRs once a wakeup is detected. This is
accomplished by registering an interrupt handler for PRCM IO event,
which is raised every time the HW detects wakeups.
[paul@pwsan.com: This patch is a merge of Govindraj R's "ARM: OMAP2+:
hwmod: Add API to check IO PAD wakeup status" patch, Tero Kristo's
"ARM: OMAP2+: mux: add support for PAD wakeup interrupts" patch, and
part of Tero's "ARM: OMAP: mux: add support for selecting mpu_irq for
each wakeup pad" patch.]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: reduced indentation level; renamed omap_hwmod function;
improved function documentation; modified to iterate only through dynamic
pads; modified to skip pads where idle mode doesn't enable wakeups; split
patches]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The ehci and ohci drivers does not use the APIs of the usbhs
core driver; the runtime pm APIs are used for clock
enable/disable. Since usbhs is parent platform device of the
ehci and ohci devices, the runtime apis indirectly uses the
usb hs core device as input parameter to for clock functions.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add hwmod support to enable access to UART4 of the AM35xx series of
chips. The UART4 device referenced from the TRM will show up as ttyO3.
This was tested on an AM3505.
Signed-off-by: Kyle Manna <kyle.manna@fuel7.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Omap_uart_can_sleep function blocks system wide low power state until
uart is active remove this func and add qos requests to prevent
MPU from transitioning.
Keep qos request to default value which will allow MPU to transition
and while uart baud rate is available calculate the latency value
from the baudrate and use the same to hold constraint while uart clocks
are enabled, and if uart is auto-idled the constraint is updated with
default constraint value allowing MPU to transition.
Qos requests are blocking notifier calls so put these requests to
work queue, also the driver uses irq_safe version of runtime API's
and callbacks can be called in interrupt disabled context.
So to avoid warn on slow path warning while using qos update
API's from runtime callbacks use the qos_work_queue.
During bootup the runtime_resume call backs might not be called and runtime
callback gets called only after uart is idled by setting the autosuspend
timeout. So qos_request from runtime resume callback might not activated during
boot if uart baudrate is calculated during bootup for console uart, so schedule
the qos_work queue once we calc_latency while configuring the uart port.
Flush and complete any pending qos jobs in work queue while suspending.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
When using DMA there are two timeouts defined. The first timeout,
rx_timeout, is really a polling rate in which software polls the
DMA status to see if the DMA has finished. This is necessary for
the RX side because we do not know how much data we will receive.
The secound timeout, RX_TIMEOUT, is a timeout after which the
DMA will be stopped if no more data is received. To make this
clearer, rename rx_timeout as rx_poll_rate and rename the
function serial_omap_rx_timeout() to serial_omap_rxdma_poll().
The OMAP-Serial driver defines an RX_TIMEOUT of 3 seconds that is
used to indicate when the DMA for UART can be stopped if no more
data is received. The value is a global definition that is applied
to all instances of the UART.
Each UART may be used for a different purpose and so the timeout
required may differ. Make this value configurable for each UART so
that this value can be optimised for power savings.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
The following UART parameters are defined within the UART driver:
1). Whether the UART uses DMA (dma_enabled), by default set to 0
2). The size of dma buffer (set to 4096 bytes)
3). The time after which the dma should stop if no more data is received.
4). The auto suspend delay that will be passed for pm_runtime_autosuspend
where uart will be disabled after timeout
Different UARTs may be used for different purpose such as the console,
for interfacing bluetooth chip, for interfacing to a modem chip, etc.
Therefore, it is necessary to be able to customize the above settings
for a given board on a per UART basis.
This change allows these parameters to be configured from the board file
and allows the parameters to be configured for each UART independently.
If a board does not define its own custom parameters for the UARTs, then
use the default parameters in the structure "omap_serial_default_info".
The default parameters are defined to be the same as the current settings
in the UART driver to avoid breaking the UART for any cuurnelty supported
boards. By default, make all boards use the default UART parameters.
Signed-off-by: Deepak K <deepak.k@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
From the runtime callbacks enable hwmod wakeups for uart which will
internally enable io-pad wakeups for uarts if they have rx-pad pins
set as wakeup capabale.
Use the io-ring wakeup mechanism after uart clock gating and leave
the PM_WKST set for uart to default reset values cleanup the
code in serial.c which was handling PM_WKST reg.
Irq_chaing(PRM_DRIVER) is used to wakeup uart after uart clocks are gated
using pad wakeup mechanism.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move the errata handling mechanism from serial.c to omap-serial file
and utilise the same func in driver file.
Errata i202, i291 are moved to be handled with omap-serial
Moving the errata macro from serial.c file to driver header file
as from on errata will be handled in driver file itself.
Corrected errata id from chapter reference 2.15 to errata id i291.
Removed errata and dma_enabled fields from omap_uart_state struct
as they are no more needed with errata handling done within omap-serial.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Avoid unconditional context restore every time we gate uart
clocks. Check whether context loss happened based on which
we can context restore uart regs from uart_port structure.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove the uart reset function which is configuring the
TX empty irq which can now be handled within omap-serial driver.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add missing uart regs to uart_port structure which can be used in
context restore. Store dll, dlh, mdr1, scr, efr, lcr, mcr reg values
into uart_port structure while configuring individual port in termios
function.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
The mapbase (start_address), membase(io_remap cookie) part of
pdata struct omap_uart_port_info are removed as this should be
derived within driver.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently we use a shared irq handler to identify uart activity and then
trigger a timer. By default the timeout value is zero and can be set or
modified from sysfs. If there was no uart activity for the period set
through sysfs, the timer will expire and call timer handler this will
set a flag can_sleep using which decision to gate uart clocks can be taken.
Since the clock gating mechanism is outside the uart driver, we currently
use this mechanism. In preparation to runtime implementation for omap-serial
driver we can cleanup this mechanism and use runtime API's to gate uart clocks.
Removes the following:
* timer related info from local uart_state struct
* the code used to set timeout value from sysfs.
* irqflags used to set shared irq handler.
* un-used function omap_uart_check_wakeup.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de> (for drivers/tty changes)
Signed-off-by: Kevin Hilman <khilman@ti.com>
In preparation to UART runtime conversion remove uart specific calls
from pm24xx/34xx files and their definition from serial.c
These func calls will no more be used with upcoming uart runtime design.
1.) omap_uart_prepare_suspend :- can be taken care with driver suspend hooks.
2.) omap_uart_enable_irqs :- Used to enable/disable uart irq's in suspend
path from PM code, this is removed as same is handled by
uart_suspend_port/uart_resume_port in omap-serial driver which will
do an port_shutdown on suspend freeing irq and port_startup on resume
enabling back irq.
3.) Remove prepare_idle/resume_idle calls used to gate uart clocks.
UART clocks can be gated within driver using runtime funcs
and be woken up using irq_chaining from omap_prm driver.
4.) Remove console_locking from idle path as clock gating is done withing
driver itself with runtime API. Remove is_suspending check used to acquire
console_lock.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Adding ti81xx_musb_phy_power() which will be used by musb driver through
its function pointer in board_data.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds minimal support and build configuration for TI8148 EVM. Also
adds support for low level debugging on UART1 console on the EVM.
Note that existing TI8168 EVM file (board-ti8168evm.c) is updated with machine
info for TI8148 EVM.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds cpu type, macros for identification of TI814X device.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_TI814X for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates existing macros, functions used for TI816X, to enable
addition of other SoCs belonging to TI81XX family (e.g., TI814X).
The approach taken is to use TI81XX/ti81xx for code/data going to be common
across all TI81XX devices.
cpu_is_ti81xx() is introduced to handle code common across TI81XX devices.
In addition, ti8168_evm_map_io() is now replaced with ti81xx_map_io() and moved
in mach-omap2/common.c as same will be used for TI814X and is not board
specific.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
allow for the omap4430 es2.3 revision to be recognized in the
omap4_check_revision() function.
most aspects of all omap4430 es2.x versions are identical, however
a number of small variations such as default pullup or pulldown
resistor configurations vary between revisions.
detailed information on silicon errata for omap4430 revisions can
be found at http://focus.ti.com/pdfs/wtbu/swpz009D.pdf
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common machine specific source files for
support for AM33XX/AM335x with cpu type, macros for identification of
AM33XX/AM335X device.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated for map_io and common.h changes, dropped CK_AM33XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch updates the common platform files with AM335X device
support (AM33XX family).
The approach taken in this patch is,
AM33XX device will be considered as OMAP3 variant, and a separate
SoC class created for AM33XX family of devices with a subclass type
for AM335X device, which is newly added device in the family.
This means, cpu_is_omap34xx(), cpu_is_am33xx() and cpu_is_am335x()
checks will return success on AM335X device.
A kernel config option CONFIG_SOC_OMAPAM33XX is added under OMAP3
to include support for AM33XX build.
Also, cpu_mask and RATE_IN_XXX flags have crossed 8 bit hence
struct clksel_rate.flags, struct prcm_config.flags and cpu_mask
are changed to u16 from u8.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Hemant Pedanekar <hemantp@ti.com>
[tony@atomide.com: left out CK_AM33XX for now]
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the DMA destination position has been asked before the
first actual data transfer has been done, the CDAC
register still contains 0 (it is initialized to 0 at
omsp_dma_start).
If CDAC == 0, return the programmed start address.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the DMA source position has been asked before the
first actual data transfer has been done, the CSAC
register does not contain valid information.
We can identify this situation by checking the CDAC
register:
CDAC != 0 indicates that the DMA transfer on the channel has
been started already.
When CDAC == 0 we can not trust the CSAC value since it has
not been updated, and can contain random number.
Return the start address in case the DMA has not jet started.
Note: The CDAC register has been initialized to 0 at dma_start
time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to comments in omap1_select_table_rate(), reprogramming dpll1
is tricky, and should always be done from SRAM.
While being at it, move OMAP730 special case handling inside
omap_sram_reprogram_clock().
Created on top of version 2 of the series "ARM: OMAP1: Fix dpll1
reprogramming related issues", which it depends on.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For still better multi-OMAP1 support, expand omap1_rate_table with flags
for different SoC types and match them while selecting clock rates. The
idea is stolen from current omap24xx clock rate selection algorithm.
Since clkdev platform flag definitions are reused here, those had to be
expanded with one extra entry for OMAP1710 subtype, as this is the only
SoC for which we allow selection of the highest, 216 MHz rate.
Once done, remove no longer needed clock rate configure time options.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now that we're always reprogramming the core clock we must make
sure SRAM works. It seems that neither omap1621 or omap1623
has 256K of SRAM. Set the SRAM size to safe value of 16K.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pm_caps field to omap2_hsmmc_info and omap_mmc_slot_data
structs, so we will be able to indicate mmc pm capabilities
in the board file.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 SOC, intecronnects has many write buffers in the async bridges
and they need to be drained before CPU enters into standby state.
Patch 'OMAP4: PM: Add CPUX OFF mode support' added CPU PM support
but OMAP errata i688 (Async Bridge Corruption) needs to be taken
care to avoid issues like system freeze, CPU deadlocks, random
crashes with register accesses, synchronisation loss on initiators
operating on both interconnect port simultaneously.
As per the errata, if a data is stalled inside asynchronous bridge
because of back pressure, it may be accepted multiple times, creating
pointer misalignment that will corrupt next transfers on that data
path until next reset of the system (No recovery procedure once
the issue is hit, the path remains consistently broken).
Async bridge can be found on path between MPU to EMIF and
MPU to L3 interconnect. This situation can happen only when the
idle is initiated by a Master Request Disconnection (which is
trigged by software when executing WFI on CPU).
The work-around for this errata needs all the initiators
connected through async bridge must ensure that data path
is properly drained before issuing WFI. This condition will be
met if one Strongly ordered access is performed to the
target right before executing the WFI. In MPU case, L3 T2ASYNC
FIFO and DDR T2ASYNC FIFO needs to be drained. IO barrier ensure
that there is no synchronisation loss on initiators operating
on both interconnect port simultaneously.
Thanks to Russell for a tip to conver assembly function to
C fuction there by reducing 40 odd lines of code from the patch.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Allocate the memory to save secure ram context which needs
to be done when MPU is hitting OFF mode.
The ROM code expects a physical address to this memory
and hence use memblock APIs to reserve this memory as part
of .reserve() callback. Maximum size as per secure RAM requirements
is allocated.
To keep omap1 build working, omap-secure.h file is created
under plat-omap directory.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds SAR RAM support on OMAP4430. SAR RAM used to save
and restore the HW context in low power modes.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Otherwise we get the following error:
In function 'omap_init_consistent_dma_size':
error: implicit declaration of function 'init_consistent_dma_size'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Eliminate the public omap_find_iommu_device() method, and don't
expect clients to provide the omap_iommu handle anymore.
Instead, OMAP's iommu driver now utilizes dev_archdata's private iommu
extension to be able to access the required iommu information.
This way OMAP IOMMU users are now able to use the generic IOMMU API without
having to call any omap-specific binding method.
Update omap3isp appropriately.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
Declare an omap iommu private struct, which binds an iommu user
to its iommu device. This struct should be placed at the iommu user's
dev_archdata so generic IOMMU API can be used without having to
utilize omap-specific plumbing anymore.
While at it, provide an accessor method to ease the retrieval of the
omap_iommu handle from a user device.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Hiroshi Doyu <hdoyu@nvidia.com>
The below patch fixes some typos in various parts of the kernel, as well as fixes some comments.
Please let me know if I missed anything, and I will try to get it changed and resent.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
arch/arm/mach-omap2/board-4430sdp.c
arch/arm/mach-omap2/board-omap4panda.c
arch/arm/mach-omap2/include/mach/omap4-common.h
arch/arm/plat-omap/include/plat/irqs.h
The changes to omap4-common.h were moved to arch/arm/mach-omap2/common.h
and the other trivial conflicts resolved. The now empty ifdef in irqs.h
was also eliminated.
A generic version should replace this later.
As io.c has become nearly empty, omap_init_consistent_dma_size() is moved
into common.c so that io.c can be removed entirely.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Kevin Hilman <khilman@ti.com>
As suggested by Russell King - ARM Linux <linux@arm.linux.org.uk>,
there's no need to keep local prototypes in non-local headers.
Add mach-omap1/common.h and mach-omap2/common.h and move the
local prototypes there from plat/common.h and mach/omap4-common.h.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that MULTI_IRQ_HANDLER is selected by all the in-tree
GIC users, make it mandatory and remove the unused macros.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Convert the omap2plus platforms to be using CONFIG_MULTI_IRQ_HANDLER.
Each machine is modified to provide either omap2_intc_handle_irq(),
omap3_intc_handle_irq() or gic_handle_irq().
This allows for a major cleanup, removing the MULTI_OMAP setup
from the interrupt path.
Tested on both Panda and IGEPv2 (single kernel image)
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Provide the OMAP2/3 IRQ code with low level handlers that can be used
by platforms using CONFIG_MULTI_IRQ_HANDLER. Though the handlers are
written in C, the compiled code looks very similar to its assembly
counterpart (at least with my gcc 4.4.1).
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Without this patch we get the following error:
arch/arm/mach-omap2/clkt_dpll.c: In function '_dpll_test_fint':
arch/arm/mach-omap2/clkt_dpll.c:98: error: 'struct dpll_data' has no member named 'flags'
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move OMAP cpufreq driver from arch/arm/mach-omap2 into
drivers/cpufreq, along with a few cleanups:
- generalize support for better handling of different SoCs in the OMAP
- use OPP layer instead of OMAP clock internals for frequency table init
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[khilman@ti.com: move to drivers]
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.
The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.
This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.
The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Include linux/export.h to fix below build warning:
CC arch/arm/plat-omap/omap_device.o
arch/arm/plat-omap/omap_device.c:1055: warning: data definition has no type or storage class
arch/arm/plat-omap/omap_device.c:1055: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
arch/arm/plat-omap/omap_device.c:1055: warning: parameter names (without types) in function declaration
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
There is no use for omap-alsa.h and board-palmz71.c doesn't need it either.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
get_context_loss_count functions return context loss count as u32, and
zero means an error. However, zero is also returned when context has
never been lost and could also be returned when the context loss count
has wrapped and goes to zero.
Change the functions to return an int, with negative value meaning an
error.
OMAP HSMMC code uses omap_pm_get_dev_context_loss_count(), but as the
hsmmc code handles the returned value as an int, with negative value
meaning an error, this patch actually fixes hsmmc code also.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated to fix a warning with recent dmtimer changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 4d17aeb1c5 ("OMAP: I2C: split
device registration and convert OMAP2+ to omap_device") makes
omap2_i2c_add_bus() return a pointer to an omap_device instead on
success instead of 0.
This breaks the omap_register_i2c_bus() ABI and results in the igep0020
board code detecting an I2C bus registration error when there is none.
Fix the problem by using PTR_RET() instead of PTR_ERR() in
omap2_i2c_add_bus().
Reported-by: Alexander Kinzer <a.kinzer@plusoptix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: updated to return pdev instead of od]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include linux/module.h to fix below build error:
CC arch/arm/plat-omap/dmtimer.o
arch/arm/plat-omap/dmtimer.c:184: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:184: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:184: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:215: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:215: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:215: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:228: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:228: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:228: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:234: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:234: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:234: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:240: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:240: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:240: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:248: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:248: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:248: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:294: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:294: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:294: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:302: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:302: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:302: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:316: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:316: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:316: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:344: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:344: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:344: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:361: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:361: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:361: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:380: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:380: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:380: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:406: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:406: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:406: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:443: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:443: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:443: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:468: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:468: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:468: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:494: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:494: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:494: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:517: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:517: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:517: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:534: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:534: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:534: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:549: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:549: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:549: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:561: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:561: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:561: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:572: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:572: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:572: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:587: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:587: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:587: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:604: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:604: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:604: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:746: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-omap/dmtimer.c:746: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:746: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
arch/arm/plat-omap/dmtimer.c:746: warning: function declaration isn't a prototype
arch/arm/plat-omap/dmtimer.c:747: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-omap/dmtimer.c:747: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:747: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
arch/arm/plat-omap/dmtimer.c:747: warning: function declaration isn't a prototype
arch/arm/plat-omap/dmtimer.c:748: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-omap/dmtimer.c:748: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:748: warning: type defaults to 'int' in declaration of 'MODULE_ALIAS'
arch/arm/plat-omap/dmtimer.c:748: warning: function declaration isn't a prototype
arch/arm/plat-omap/dmtimer.c:749: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-omap/dmtimer.c:749: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:749: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
arch/arm/plat-omap/dmtimer.c:749: warning: function declaration isn't a prototype
make[1]: *** [arch/arm/plat-omap/dmtimer.o] Error 1
make: *** [arch/arm/plat-omap] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'next/cleanup2' of git://git.linaro.org/people/arnd/arm-soc: (31 commits)
ARM: OMAP: Warn if omap_ioremap is called before SoC detection
ARM: OMAP: Move set_globals initialization to happen in init_early
ARM: OMAP: Map SRAM later on with ioremap_exec()
ARM: OMAP: Remove calls to SRAM allocations for framebuffer
ARM: OMAP: Avoid cpu_is_omapxxxx usage until map_io is done
ARM: OMAP1: Use generic map_io, init_early and init_irq
arm/dts: OMAP3+: Add mpu, dsp and iva nodes
arm/dts: OMAP4: Add a main ocp entry bound to l3-noc driver
ARM: OMAP2+: l3-noc: Add support for device-tree
ARM: OMAP2+: board-generic: Add i2c static init
ARM: OMAP2+: board-generic: Add DT support to generic board
arm/dts: Add support for OMAP3 Beagle board
arm/dts: Add initial device tree support for OMAP3 SoC
arm/dts: Add support for OMAP4 SDP board
arm/dts: Add support for OMAP4 PandaBoard
arm/dts: Add initial device tree support for OMAP4 SoC
ARM: OMAP: omap_device: Add a method to build an omap_device from a DT node
ARM: OMAP: omap_device: Add omap_device_[alloc|delete] for DT integration
of: Add helpers to get one string in multiple strings property
ARM: OMAP2+: devices: Remove all omap_device_pm_latency structures
...
Fix up trivial header file conflicts in arch/arm/mach-omap2/board-generic.c
* 'next/pm' of git://git.linaro.org/people/arnd/arm-soc: (66 commits)
ARM: CSR: PM: use outer_resume to resume L2 cache
ARM: CSR: call l2x0_of_init to init L2 cache of SiRFprimaII
ARM: OMAP: voltage: voltage layer present, even when CONFIG_PM=n
ARM: CSR: PM: add sleep entry for SiRFprimaII
ARM: CSR: PM: save/restore irq status in suspend cycle
ARM: CSR: PM: save/restore timer status in suspend cycle
OMAP4: PM: TWL6030: add cmd register
OMAP4: PM: TWL6030: fix ON/RET/OFF voltages
OMAP4: PM: TWL6030: address 0V conversions
OMAP4: PM: TWL6030: fix uv to voltage for >0x39
OMAP4: PM: TWL6030: fix voltage conversion formula
omap: voltage: add a stub header file for external/regulator use
OMAP2+: VC: more registers are per-channel starting with OMAP5
OMAP3+: voltage: update nominal voltage in voltdm_scale() not VC post-scale
OMAP3+: voltage: rename omap_voltage_get_nom_volt -> voltdm_get_voltage
OMAP3+: voltdm: final removal of omap_vdd_info
OMAP3+: voltage: move/rename curr_volt from vdd_info into struct voltagedomain
OMAP3+: voltage: rename scale and reset functions using voltdm_ prefix
OMAP3+: VP: combine setting init voltage into common function
OMAP3+: VP: remove unused omap_vp_get_curr_volt()
...
Fix up trivial conflict in arch/arm/mach-prima2/l2x0.c (code removal vs
edit)
* 'for-linus/i2c-3.2' of git://git.fluff.org/bjdooks/linux: (47 commits)
i2c-s3c2410: Add device tree support
i2c-s3c2410: Keep a copy of platform data and use it
i2c-nomadik: cosmetic coding style corrections
i2c-au1550: dev_pm_ops conversion
i2c-au1550: increase timeout waiting for master done
i2c-au1550: remove unused ack_timeout
i2c-au1550: remove usage of volatile keyword
i2c-tegra: __iomem annotation fix
i2c-eg20t: Add initialize processing in case i2c-error occurs
i2c-eg20t: Fix flag setting issue
i2c-eg20t: add stop sequence in case wait-event timeout occurs
i2c-eg20t: Separate error processing
i2c-eg20t: Fix 10bit access issue
i2c-eg20t: Modify returned value s32 to long
i2c-eg20t: Fix bus-idle waiting issue
i2c-designware: Fix PCI core warning on suspend/resume
i2c-designware: Add runtime power management support
i2c-designware: Add support for Designware core behind PCI devices.
i2c-designware: Push all register reads/writes into the core code.
i2c-designware: Support multiple cores using same ISR
...
These files will fail to compile if we dont clean them up in advance
and have them include the appropriate headers they need.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These files all make use of one of the EXPORT_SYMBOL variants
or the THIS_MODULE macro. So they will need <linux/export.h>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (33 commits)
iommu/core: Remove global iommu_ops and register_iommu
iommu/msm: Use bus_set_iommu instead of register_iommu
iommu/omap: Use bus_set_iommu instead of register_iommu
iommu/vt-d: Use bus_set_iommu instead of register_iommu
iommu/amd: Use bus_set_iommu instead of register_iommu
iommu/core: Use bus->iommu_ops in the iommu-api
iommu/core: Convert iommu_found to iommu_present
iommu/core: Add bus_type parameter to iommu_domain_alloc
Driver core: Add iommu_ops to bus_type
iommu/core: Define iommu_ops and register_iommu only with CONFIG_IOMMU_API
iommu/amd: Fix wrong shift direction
iommu/omap: always provide iommu debug code
iommu/core: let drivers know if an iommu fault handler isn't installed
iommu/core: export iommu_set_fault_handler()
iommu/omap: Fix build error with !IOMMU_SUPPORT
iommu/omap: Migrate to the generic fault report mechanism
iommu/core: Add fault reporting mechanism
iommu/core: Use PAGE_SIZE instead of hard-coded value
iommu/core: use the existing IS_ALIGNED macro
iommu/msm: ->unmap() should return order of unmapped page
...
Fixup trivial conflicts in drivers/iommu/Makefile: "move omap iommu to
dedicated iommu folder" vs "Rename the DMAR and INTR_REMAP config
options" just happened to touch lines next to each other.
Most of the OMAP1 implementation flags are set statically, with the
exception that omap7xx has its data bus wired up differently.
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This is how the driver can find the flags for its implementation
functionality in its platform_data
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Mark each OMAP I2C bus with the hwmod's knowledge of which I2C
IP version is in the chip we're running on.
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
All OMAP1 are using "IP revision 1" in terms of register
layout. We set this information in omap1_i2c_add_bus() so
we don't have to use cpu_is_xxx() any more in the omap i2c
driver.
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits)
mmc: fix compile error when CONFIG_BLOCK is not enabled
mmc: core: Cleanup eMMC4.5 conditionals
mmc: omap_hsmmc: if multiblock reads are broken, disable them
mmc: core: add workaround for controllers with broken multiblock reads
mmc: core: Prevent too long response times for suspend
mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
mmc: core: support HPI send command
mmc: core: Add cache control for eMMC4.5 device
mmc: core: Modify the timeout value for writing power class
mmc: core: new discard feature support at eMMC v4.5
mmc: core: mmc sanitize feature support for v4.5
mmc: dw_mmc: modify DATA register offset
mmc: sdhci-pci: add flag for devices that can support runtime PM
mmc: omap_hsmmc: ensure pbias configuration is always done
mmc: core: Add Power Off Notify Feature eMMC 4.5
mmc: sdhci-s3c: fix potential NULL dereference
mmc: replace printk with appropriate display macro
mmc: core: Add default timeout value for CMD6
mmc: sdhci-pci: add runtime pm support
...
When device data indicates that multiple block reads are not supported
on a given HSMMC controller instance, log a message to the console, and
pass the appropriate MMC capability flag to the MMC core.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We don't have cpu_is_omapxxxx SoC detection initialized until
SoC detection is initialized from init_early.
Note that with the common map_io we should no longer need
cpu_is_omapxxxx for ioremap.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we can't do generic map_io as we currently rely on
static mappings that work only because of arch_ioremap.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to remove omap hacks for map_io.
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This assumes fixed mappings which will not work once we move
to use ioremap_exec(). It seems that these are currently
not in use, or in use for some out of tree corner cases.
If SRAM support for framebuffer is wanted, it should be done
with ioremap in the driver.
Note that further removal of the code can now be done,
but that can be done seprately by the driver maintainers.
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we don't need to initialize SoC detection early
and can start using generic map_io.
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows removing omap hacks for map_io allowing generic
map_io.
Note that in the future we can't do cpu_is_omapxxxx detection
until in init_early. This means that board-innovator.c now
assumes 15xx only, and board-generic.c assumes 16xx only.
This is best fixed later on by passing the SoC type from
device tree.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Given that we want the default to not have any <mach/memory.h> and given
that there are now fewer cases where it is still provided than the cases
where it is not at this point, this makes sense to invert the logic and
just identify the exception cases.
The word "need" instead of "have" was chosen to construct the config
symbol so not to suggest that having a mach/memory.h file is actually
a feature that one should aim for.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
The way that we detect which OMAP3 chips support I/O wakeup and
software I/O chain clock control is broken.
Currently, I/O wakeup is marked as present for all OMAP3 SoCs other
than the AM3505/3517. The TI81xx family of SoCs are at present
considered to be OMAP3 SoCs, but don't support I/O wakeup. To resolve
this, convert the existing blacklist approach to an explicit,
whitelist support, in which only SoCs which are known to support I/O
wakeup are listed. (At present, this only includes OMAP34xx,
OMAP3503, OMAP3515, OMAP3525, OMAP3530, and OMAP36xx.)
Also, the current code incorrectly detects the presence of a
software-controllable I/O chain clock on several chips that don't
support it. This results in writes to reserved bitfields, unnecessary
delays, and console messages on kernels running on those chips:
http://www.spinics.net/lists/linux-omap/msg58735.html
Convert this test to a feature test with a chip-by-chip whitelist.
Thanks to Dave Hylands <dhylands@gmail.com> for reporting this problem
and doing some testing to help isolate the cause. Thanks to Steve
Sakoman <sakoman@gmail.com> for catching a bug in the first version of
this patch. Thanks to Russell King <linux@arm.linux.org.uk> for
comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add a notifier called during device_add phase. If an of_node is present,
retrieve the hwmod entry in order to populate properly the omap_device
structure.
For the moment the resource from the device-tree are overloaded.
DT does not support named resource yet, and thus, most driver will not
work without that information.
Add a documentation to capture the specifics OMAP bindings needed for
device-tree support.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Split the omap_device_build_ss into two smaller functions
that will allow to populate a platform_device already allocated by
device-tree.
The functionality of the omap_device_build_ss is still the same, but
the omap_device_alloc will be usable with devices already built by
device-tree.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove all these duplicated structures since a default one is now
available.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Most devices are using the same default omap_device_pm_latency structure
during device built. In order to avoid the duplication of the same
structure everywhere, add a default structure that will be used if
the device does not have an explicit one.
Next patches will clean the duplicated structures.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
An API which translates a standard hwmod name to corresponding
platform_device is useful for drivers when they need to look up the
device associated with a hwmod name to map back into the device
structure pointers. These ideally should be used by drivers in
mach directory. Using a generic hwmod name like "gpu" instead of
the actual device name which could change in the future, allows
us to:
a) Could in effect help replace apis such as omap2_get_mpuss_device,
omap2_get_iva_device, omap2_get_l3_device, omap4_get_dsp_device,
etc..
b) Scale to more devices rather than be restricted to named functions
c) Simplify driver's platform_data from passing additional fields
all doing the same thing with different function pointer names
just for accessing a different device name.
Signed-off-by: Nishanth Menon <nm@ti.com>
[b-cousson@ti.com: Adapt it to the new pdev pointer inside od,
remove the unneeded helpers, and fold the next patch here]
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Support for IDE drivers should not be automatic, since most platforms
cannot actually support any IDE low-level drivers. This partly
reverts 2064c946e "ARM: always select HAVE_IDE" to set this symbol
only when either a PC-style bus (PCI, ISA, PCMCIA) is enabled or
a platform is used that is known to have an existing driver in
drivers/ide.
New platforms should not need this option and just use CONFIG_ATA
with drivers/ata/.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The omap_dm_timer_remove function gets discarded when
CONFIG_HOTPLUG is not set, so we must not reference it
unconditionally.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add SoC specific map_io function to be used by the generic DT
board file. This is an intermediate step before having some
generic DT aware map_io function.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This generalizes the omap2_mcbsp1_mux_clkr_src and omap2_mcbsp1_mux_fsr_src
implementation between generic McBSP and OMAP2 specific McBSP code. These
functions are used to select source for CLKR and FSR signals on OMAP2+.
Start generalizing the code by implementing an optional mux_signal function
pointer in platform data that will implement the actual muxing and which is
called now from omap2_mcbsp1_mux_clkr_src and omap2_mcbsp1_mux_fsr_src.
These functions are to be removed later and cleanup the API so that
mux_signal gets its arguments directly from client code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This generalizes the omap2_mcbsp_set_clks_src implementation between generic
McBSP and OMAP2 specific McBSP code. Currently this function is used to
select either internal fclk or clks pin as a McBSP CLKS source on OMAP2+.
Implement generalization by having an optional set_clk_src function pointer
in platform data that is used to select parent for a given clock. Idea is to
pass higher level source clock name (later coming from client driver) that
platform specific code will map to platform specific clock name.
API cleanup between McBSP and client code comes later.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These address definitions are OMAP1 specific can be in single source file.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hardware.h is not needed here and let the definition for struct clk to come
via linux/clk.h.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Sidetone resource is already registered for a device so there is no need
for cpu_is_omap34xx() and McBSP port number tests in the driver. We can
cleanup and make the code generic by dropping remaining CONFIG_ARCH_OMAP3
conditional compilations and then using sidetone resource and st_data
variable for runtime tests.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Active sidetone requires that McBSP interface clock doesn't idle and there
is no mechanism in hwmod to turn autoidling on/off in runtime. McBSP2 and 3
in OMAP34xx share their interface clock with McBSP sidetone module and
that interface clock must be active when the sidetone is operating.
Sidetone has its own autoidle bit which should keep the interface clock
active but it is broken. Putting the McBSP core to no-idle mode when the
sidetone is active is no good either since it results to higher power
consumption when using the threshold based DMA transfers.
For making the McBSP code more generic, move this sidetone clock management
with fixme comments to mach-omap2/mcbsp.c and pass pointer to it via
platform data.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Wamsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rationale here is to remove one global variable and to make possible to have
variable size McBSP register maps inside SoC.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove CONFIG_ARCH_OMAP3 conditional compilation and cpu_is_omap34xx test
around buffer threshold based transfer and DMA operating mode control. Use
instead the buffer_size in platform data to determine when these sysfs
controls are exposed and when to access related McBSP registers. Rationale
for this is to make code generic and to allow to use it on OMAP4 that also
supports threshold based transfers.
Currently buffer_size variable is set only for OMAP3 SoCs but it is easy
to extend to OMAP4 and any later OMAP version.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
McBSP transmit and receive configuration control registers must be set up
for OMAP2430 and later. Replace is_omap tests in generic code with a new
feature flag has_ccr in platform data so that there is no need to change
code for any upcoming OMAP version.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently wakeup control code is compiled only when CONFIG_ARCH_OMAP3 is
set even it should be available for CONFIG_ARCH_OMAP4 only builds also.
Fix this by making wakeup control generic so that it is executed whenever
new feature flag has_wakeup in platform data is set. Currently flag is set
for McBSP config types 3 and 4.
Remove also old comments about idle mode settings and HW bug workarounds
that were not updated during hwmod conversion.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Register access can be made more generic by calculating register address
offsets runtime from common register definitions and by using reg_size and
reg_step variables that are passed via platform data. Common register
definitions are possible since McBSP registers are ordered similarly between
OMAP versions.
Remove also references to OMAP2+ specific config_type variable from generic
McBSP code since other variables and feature flags are better to carry needed
information from platform code.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Only OMAP1s are using omap_mcbsp_register_board_cfg after OMAP2+ hwmod
conversion so it can be moved to mach-omap1/mcbsp.c.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These variables got unused after McBSP was converted to use resource
structures.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is the first step to remove PLAT_PHYS_OFFSET usage from the debug
UART code.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Fix the address overlap with Emulation domain (EMU).
The previous mapping was entering into EMU mapping
and was not as per comments. Fix the mapping accordingly.
Signed-off-by: Girish S G <girishsg@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Clock is enabled only when timer is started and disabled when the the timer
is stopped. Therefore before accessing registers in functions clock is enabled
and then disabled back at the end of access. Context save is done dynamically
whenever the registers are modified. Context restore is called when context is
lost.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[tony@atomide.com: updated to use revision instead of tidr]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pass the reserved flag in pdata and use it. We can
now make sys_timer_reserved static to mach-omap2/timer.c.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pm_runtime feature to dmtimer whereby *_runtime_get_sync()
is called within omap_dm_timer_enable(), pm_runtime_put()
is called in omap_dm_timer_disable(). In addition to calling
pm_runtime_enable, we are calling pm_runtime_irq_safe so that
they can be called from interrupt context.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Register timer devices by going through hwmod database using
hwmod API. The driver probes each of the registered devices.
Functionality which are already performed by hwmod framework
are removed from timer code. New set of timers present on
OMAP4 are now supported.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
[tony@atomide.com: folded in spinlock changes, left out is_omap2]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add routines to converts dmtimers to platform devices. The device data
is obtained from hwmod database of respective platform and is registered
to device model after successful binding to driver.
In addition, capability attribute of each of the timers is added in
hwmod database.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OMAP1 dmtimers into a platform devices and then registers with
device model framework so that it can be bound to corresponding driver.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The registers are slightly different between v1 and v2 ip that
is available in omap4 and later for some timers.
Add support for v2 ip by mapping the interrupt related registers
separately and adding func_base for the functional registers.
Also disable dmtimer driver features on omap4 for now as
those need the hwmod conversion series to deal with enabling
the timers properly in omap_dm_timer_init.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Tested-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rather than embedding a struct platform_device inside a struct
omap_device, decouple them, leaving only a pointer to the
platform_device inside the omap_device.
Use the arch-specific data field of the platform_device (pdev_archdata)
to add an omap_device pointer after the platform_device has been created.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Public omap_device functions need to take platform_device pointers,
conversion to omap_device pointers is done internal to the omap_device
layer.
Signed-off-by: Kevin Hilman <khilman@ti.com>
The internal device register functions do not need or use any omap_device
internals, so pass in a platform_device pointer instead of an omap_device
pointer.
Signed-off-by: Kevin Hilman <khilman@ti.com>
All of the device init and device driver interaction with omap_device
is done using platform_device pointers. To make this more explicit,
have omap_device return a platform_device pointer instead of an
omap_device pointer.
All current users of the omap_device pointer were only using it to get
at the platform_device pointer or struct device pointer, so fixing all
of the users was trivial.
This also makes it more difficult for device init code to directly
access members of struct omap_device, and allows for easier changing
of omap_device internals.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The *_device_register() functions and the count/fill resources functions
are internal to omap_device and do not need to be in the header.
Signed-off-by: Kevin Hilman <khilman@ti.com>
During normal system operation warning messages similar to this
are appearing quite often:
omap_device: omap4-keypad.-1: new worst case activate latency 0: 61035
This doesn't seem to be reporting a problem, nor is it very useful for
non-developers, so reduce it to debug level.
Acked-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
For consistency in kernel printk output for devices, use dev_dbg(),
dev_warn(), dev_err() instead of pr_debug(), pr_warning() and
pr_err(), some of which currently use direct access of name from
platform_device and others of which use dev_name(). Using the dev_*
versions uses the standard device naming from the driver core.
Some pr_* prints were not converted with this patch since they are
used before the platform_device and struct device are created so
neither the dev_* prints or dev_name() is valid.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
struct omap_device *od is only set with find_omap_device_by_dev but not used
otherwise so remove them and references to omap device API.
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Needed as some of the voltage layer functionality is accessed from the
SMPS regulator driver.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The voltage domain pointer currently in struct omap_hwmod is not used
and does not belong here. Instead, voltage domains will be associated
with powerdomains in forthcoming patches.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Now that all of the users of the OMAP_CHIP bitfield code have been converted
to use lists, the OMAP_CHIP code, data, and declarations can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
At Tony's request, remove the OMAP_CHIP* flags from the hwmod data, and
replace it instead with chip family, variant, and ES level-specific lists
of hwmods to register.
Thanks to Gražvydas Ignotas <notasas@gmail.com> for finding a bug in the
AM3517/3505 support, and for other review comments.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
The OMAP_REVBITS_* macros are just used as otherwise meaningless
aliases for the numbers zero through five, so remove these macros.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Abhilash Koyamangalath <abhilash.kv@ti.com>
Use explicit revision codes for OMAP/AM 3505/3517 ES levels, as the rest
of the OMAP2+ SoCs do in mach-omap2/cpu.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Abhilash Koyamangalath <abhilash.kv@ti.com>
Start using the generic fault report mechanism, as provided by
the IOMMU core, and remove its now-redundant omap_iommu_set_isr API.
Currently we're only interested in letting upper layers know about the
fault, so in case the faulting device is a remote processor, they could
restart it.
Dynamic PTE/TLB loading is not supported.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The OMAP3505/AM3505 appears to be based on the same silicon as the
OMAP3517/AM3517, with some features disabled via eFuse bits. Follow
the same practice as OMAP3430 and identify these devices internally as
part of the OMAP3517/AM3517 family.
The OMAP3503/3515/3525/3530 chips appear to be based on the same silicon
as the OMAP3430, with some features disabled via eFuse bits. Identify
these devices internally as part of the OMAP3430 family.
Remove the old OMAP35XX_CLASS, which actually covered two very different
chip families. The OMAP3503/3515/3525/3530 chips will now be covered by
OMAP343X_CLASS, since the silicon appears to be identical. For the
OMAP3517/AM3517 family, create a new class, OMAP3517_CLASS.
Thanks to Tony Lindgren <tony@atomide.com> for some help with the second
revision of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Abhilash Koyamangalath <abhilash.kv@ti.com>
The suspend/resume _noirq handlers were #ifdef'd out in the
!CONFIG_SUSPEND case, but were still assigned to the dev_pm_ops
struct. Fix by defining them to NULL in the !CONFIG_SUSPEND case.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Prepend 'omap_' to OMAP's 'struct iommu' and exposed API, to prevent
namespace pollution and generally to improve readability of the code
that still uses the driver directly.
Update the users as needed as well.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Remove unused public APIs from OMAP's iommu driver.
IOMMU functionality should be exposed only via the generic IOMMU API;
this way drivers stay generic, and different IOMMU drivers
don't need to duplicate similar functionalities.
The rest of the API still exposed by OMAP's iommu will be evaluated
and eventually either added to the generic IOMMU API (if relevant),
or completely removed.
The intention is that OMAP's iommu driver will eventually not expose
any public API.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Remove unused functionality from OMAP's iovmm module.
The intention is to eventually completely replace iovmm with the
generic DMA-API, so new code that'd need this iovmm functionality
will have to extend the DMA-API instead.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Stop exporting functions that are used only within the iommu
driver itself.
Eventually OMAP's iommu driver should only expose API via the generic
IOMMU framework.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Move OMAP's iommu drivers to the dedicated iommu drivers folder.
While OMAP's iovmm (virtual memory manager) driver does not strictly
belong to the iommu drivers folder, move it there as well, because
it's by no means OMAP-specific (in concept. technically it is still
coupled with OMAP's iommu).
Eventually, iovmm will be completely replaced with the generic,
iommu-based, dma-mapping API.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Migrate OMAP's iommu driver to the generic IOMMU API, so users can stay
generic, and any generic IOMMU functionality can be developed once
in the generic framework.
Migrate omap's iovmm (virtual memory manager) to the generic IOMMU API,
and adapt omap3isp as needed, so the latter won't break.
The plan is to eventually remove iovmm completely by replacing it
with the (upcoming) IOMMU-based DMA-API.
Tested on OMAP3 (with omap3isp) and OMAP4 (with rpmsg/remoteproc).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Commit c03f007a8b (OMAP: PM:
omap_device: add system PM methods for PM domain handling) mistakenly
used SET_SYSTEM_SLEEP_PM_OPS() when trying to configure custom methods
for the PM domains noirq methods. Fix that by setting only the
suspend_noirq and resume_noirq methods with custom versions.
Note that all other PM domain methods (including the "normal"
suspend/resume methods) are populated using USE_PLATFORM_PM_SLEEP_OPS,
which configures them all to the default subsystem (platform_bus)
methods.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Introduce them for each omap variant and just make them all call
omap2_init_common_infrastructure for now. Do this for each board-*.c
file except for board-generic and board-omap3beagle as they use
the same machine ID for multiple SoCs.
No functional changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
There's no need to call omap2_init_common_devices from init_early.
It no longer does anything else except reprogram the memory timings
for some boards, so it's better to do it later so we have a chance
to get console messages if something goes wrong.
Move it to happen after omap_serial_init gets called. And while
patching it anyways, rename it to omap_sdrc_init as suggested by
Benoit Cousson <b-cousson@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rather than marking the mach/gpio.h header files which want to use the
trivial GPIOLIB implementation, mark those which do not want to use it
instead. This means that by default, you get the trivial implementation
and only have to do something extra if you need to. This should
encourage the use of the trivial default implementation.
As an additional bonus, several gpio.h header files become empty.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many of the gpio_to_irq implementations use the gpiolib version of this
function. Provide the standard gpiolib gpio_to_irq() for everyone, but
allow platforms to override it if they wish. Add the neccessary
overrides for those platforms which do not use the standard definition.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate 24 trivial gpiolib implementions out of mach/gpio.h
into asm/gpio.h. This is basically the include of asm-generic/gpio.h
and the definition of gpio_get_value, gpio_set_value, and gpio_cansleep
as described in Documentation/gpio.txt
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: David Brown <davidb@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The pointer "va" returned from "phys_to_virt(pa)" is never used in
"sgtable_fill_kmalloc()".So,it is safe to remove this set-but-unused variable.
Signed-off-by: Maxin B. John <maxin.john@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing definitions for the AM3505/3517 UART4 such
as DMAs, INTs and base address.
Signed-of-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert arch/arm includes of mach/gpio.h and asm/gpio.h to linux/gpio.h
before we start consolidating the individual platform implementations
of the gpio header files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
OMAP1 needs this also since GPIO driver (common for all OMAPs) is
being converted to use generic IRQ chip.
Signed-off-by: Kevin Hilman <khilman@ti.com>
* 'next/devel2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (47 commits)
OMAP: Add debugfs node to show the summary of all clocks
OMAP2+: hwmod: Follow the recommended PRCM module enable sequence
OMAP2+: clock: allow per-SoC clock init code to prevent clockdomain calls from clock code
OMAP2+: clockdomain: Add per clkdm lock to prevent concurrent state programming
OMAP2+: PM: idle clkdms only if already in idle
OMAP2+: clockdomain: add clkdm_in_hwsup()
OMAP2+: clockdomain: Add 2 APIs to control clockdomain from hwmod framework
OMAP: clockdomain: Remove redundant call to pwrdm_wait_transition()
OMAP4: hwmod: Introduce the module control in hwmod control
OMAP4: cm: Add two new APIs for modulemode control
OMAP4: hwmod data: Add modulemode entry in omap_hwmod structure
OMAP4: hwmod data: Add PRM context register offset
OMAP4: prm: Remove deprecated functions
OMAP4: prm: Replace warm reset API with the offset based version
OMAP4: hwmod: Replace RSTCTRL absolute address with offset macros
OMAP: hwmod: Wait the idle status to be disabled
OMAP4: hwmod: Replace CLKCTRL absolute address with offset macros
OMAP2+: hwmod: Init clkdm field at boot time
OMAP4: hwmod data: Add clock domain attribute
OMAP4: clock data: Add missing divider selection for auxclks
...
* 'next/board' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: S3C64XX: Configure backup battery charger on Cragganmore
ARM: S3C64XX: Fix WM8915 IRQ polarity on Cragganmore
ARM: S3C64XX: Configure supplies for all Cragganmore regulators
ARM: S3C64XX: Refresh Cragganmore support
ARM: S3C64XX: Initial support for Wolfson/Simtec Cragganmore/Banff
OMAP4: Keyboard: Mux changes in the board file
omap: blaze: add mmc5/wl1283 device support
omap: 4430SDP: Register the card detect GPIO properly
arm: omap3: cm-t35: add support for cm-t3730
OMAP3: beagle: add support for beagleboard xM revision C
OMAP3: rx-51: Add full regulator definitions
omap: rx51: Platform support for lp5523 led chip
* 'next/cross-platform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
ARM: Consolidate the clkdev header files
ARM: set vga memory base at run-time
ARM: convert PCI defines to variables
ARM: pci: make pcibios_assign_all_busses use pci_has_flag
ARM: remove unnecessary mach/hardware.h includes
pci: move microblaze and powerpc pci flag functions into asm-generic
powerpc: rename ppc_pci_*_flags to pci_*_flags
Fix up conflicts in arch/microblaze/include/asm/pci-bridge.h
* 'next/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc:
MAINTAINERS: add maintainer of CSR SiRFprimaII machine
ARM: CSR: initializing L2 cache
ARM: CSR: mapping early DEBUG_LL uart
ARM: CSR: Adding CSR SiRFprimaII board support
OMAP4: clocks: Update the clock tree with 4460 clock nodes
OMAP4: PRCM: OMAP4460 specific PRM and CM register bitshifts
OMAP4: ID: add omap_has_feature for max freq supported
OMAP: ID: introduce chip detection for OMAP4460
ARM: Xilinx: merge board file into main platform code
ARM: Xilinx: Adding Xilinx board support
Fix up conflicts in arch/arm/mach-omap2/cm-regbits-44xx.h
* 'next/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (133 commits)
ARM: EXYNOS4: Change devname for FIMD clkdev
ARM: S3C64XX: Cleanup mach/regs-fb.h from mach-s3c64xx
ARM: S5PV210: Cleanup mach/regs-fb.h from mach-s5pv210
ARM: S5PC100: Cleanup mach/regs-fb.h from mach-s5pc100
ARM: S3C24XX: Use generic s3c_set_platdata for devices
ARM: S3C64XX: Use generic s3c_set_platdata for OneNAND
ARM: SAMSUNG: Use generic s3c_set_platdata for NAND
ARM: SAMSUNG: Use generic s3c_set_platdata for USB OHCI
ARM: SAMSUNG: Use generic s3c_set_platdata for HWMON
ARM: SAMSUNG: Use generic s3c_set_platdata for FB
ARM: SAMSUNG: Use generic s3c_set_platdata for TS
ARM: S3C64XX: Add PWM backlight support on SMDK6410
ARM: S5P64X0: Add PWM backlight support on SMDK6450
ARM: S5P64X0: Add PWM backlight support on SMDK6440
ARM: S5PC100: Add PWM backlight support on SMDKC100
ARM: S5PV210: Add PWM backlight support on SMDKV210
ARM: EXYNOS4: Add PWM backlight support on SMDKC210
ARM: EXYNOS4: Add PWM backlight support on SMDKV310
ARM: SAMSUNG: Create a common infrastructure for PWM backlight support
clocksource: convert 32-bit down counting clocksource on S5PV210/S5P64X0
...
Fix up trivial conflict in arch/arm/mach-imx/mach-scb9328.c
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (237 commits)
ARM: 7004/1: fix traps.h compile warnings
ARM: 6998/2: kernel: use proper memory barriers for bitops
ARM: 6997/1: ep93xx: increase NR_BANKS to 16 for support of 128MB RAM
ARM: Fix build errors caused by adding generic macros
ARM: CPU hotplug: ensure we migrate all IRQs off a downed CPU
ARM: CPU hotplug: pass in proper affinity mask on IRQ migration
ARM: GIC: avoid routing interrupts to offline CPUs
ARM: CPU hotplug: fix abuse of irqdesc->node
ARM: 6981/2: mmci: adjust calculation of f_min
ARM: 7000/1: LPAE: Use long long printk format for displaying the pud
ARM: 6999/1: head, zImage: Always Enter the kernel in ARM state
ARM: btc: avoid invalidating the branch target cache on kernel TLB maintanence
ARM: ARM_DMA_ZONE_SIZE is no more
ARM: mach-shark: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-sa1100: move ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-realview: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-pxa: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-ixp4xx: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-h720x: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
ARM: mach-davinci: move from ARM_DMA_ZONE_SIZE to mdesc->dma_zone_size
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (107 commits)
vfs: use ERR_CAST for err-ptr tossing in lookup_instantiate_filp
isofs: Remove global fs lock
jffs2: fix IN_DELETE_SELF on overwriting rename() killing a directory
fix IN_DELETE_SELF on overwriting rename() on ramfs et.al.
mm/truncate.c: fix build for CONFIG_BLOCK not enabled
fs:update the NOTE of the file_operations structure
Remove dead code in dget_parent()
AFS: Fix silly characters in a comment
switch d_add_ci() to d_splice_alias() in "found negative" case as well
simplify gfs2_lookup()
jfs_lookup(): don't bother with . or ..
get rid of useless dget_parent() in btrfs rename() and link()
get rid of useless dget_parent() in fs/btrfs/ioctl.c
fs: push i_mutex and filemap_write_and_wait down into ->fsync() handlers
drivers: fix up various ->llseek() implementations
fs: handle SEEK_HOLE/SEEK_DATA properly in all fs's that define their own llseek
Ext4: handle SEEK_HOLE/SEEK_DATA generically
Btrfs: implement our own ->llseek
fs: add SEEK_HOLE and SEEK_DATA flags
reiserfs: make reiserfs default to barrier=flush
...
Fix up trivial conflicts in fs/xfs/linux-2.6/xfs_super.c due to the new
shrinker callout for the inode cache, that clashed with the xfs code to
start the periodic workers later.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6: (51 commits)
PM: Improve error code of pm_notifier_call_chain()
PM: Add "RTC" to PM trace time stamps to avoid confusion
PM / Suspend: Export suspend_set_ops, suspend_valid_only_mem
PM / Suspend: Add .suspend_again() callback to suspend_ops
PM / OPP: Introduce function to free cpufreq table
ARM / shmobile: Return -EBUSY from A4LC power off if A3RV is active
PM / Domains: Take .power_off() error code into account
ARM / shmobile: Use genpd_queue_power_off_work()
ARM / shmobile: Use pm_genpd_poweroff_unused()
PM / Domains: Introduce function to power off all unused PM domains
OMAP: PM: disable idle on suspend for GPIO and UART
OMAP: PM: omap_device: add API to disable idle on suspend
OMAP: PM: omap_device: add system PM methods for PM domain handling
OMAP: PM: omap_device: conditionally use PM domain runtime helpers
PM / Runtime: Add new helper function: pm_runtime_status_suspended()
PM / Domains: Queue up power off work only if it is not pending
PM / Domains: Improve handling of wakeup devices during system suspend
PM / Domains: Do not restore all devices on power off error
PM / Domains: Allow callbacks to execute all runtime PM helpers
PM / Domains: Do not execute device callbacks under locks
...
* 'gpio/next' of git://git.secretlab.ca/git/linux-2.6: (61 commits)
gpio/mxc/mxs: fix build error introduced by the irq_gc_ack() renaming
mcp23s08: add i2c support
mcp23s08: isolate spi specific parts
mcp23s08: get rid of setup/teardown callbacks
gpio/tegra: dt: add binding for gpio polarity
mcp23s08: remove unused work queue
gpio/da9052: remove a redundant assignment for gpio->da9052
gpio/mxc: add device tree probe support
ARM: mxc: use ARCH_NR_GPIOS to define gpio number
gpio/mxc: get rid of the uses of cpu_is_mx()
gpio/mxc: add missing initialization of basic_mmio_gpio shadow variables
gpio: Move mpc5200 gpio driver to drivers/gpio
GPIO: DA9052 GPIO module v3
gpio/tegra: Use engineering names in DT compatible property
of/gpio: Add new method for getting gpios under different property names
gpio/dt: Refine GPIO device tree binding
gpio/ml-ioh: fix off-by-one for displaying variable i in dev_err
gpio/pca953x: Deprecate meaningless device-tree bindings
gpio/pca953x: Remove dynamic platform data pointer
gpio/pca953x: Fix IRQ support.
...
Now most of ARM machines has the alsmot same __clk_get/put() macro
So place it at the arch/arm/include/asm/clkdev.h and remove the reduntant header files
But some machines don't have the same form as above. It can use the machince specific clkdev file by HAVE_MACH_CLKDEV config
Now there are only 3 caese.
1) define the clk structure with clkdev macro => Need to move clk structure to proper header file
arch/arm/mach-versatile/include/mach/clkdev.h
arch/arm/mach-realview/include/mach/clkdev.h
arch/arm/mach-vexpress/include/mach/clkdev.h
arch/arm/mach-integrator/include/mach/clkdev.h
2) export the __clk_get/put function at clock.c
arch/arm/mach-shmobile/include/mach/clkdev.h
3) demuxing the clk source
arch/arm/mach-u300/include/mach/clkdev.h
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
By default, omap_devices will be automatically idled on suspend
(and re-enabled on resume.) Using this new API, device init code
can disable this feature if desired.
NOTE: any driver/device that has been runtime PM converted should
not be using this API.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
In the omap_device PM domain callbacks, use omap_device idle/enable to
automatically manage device idle states during system suspend/resume.
If an omap_device has not already been runtime suspended, the
->suspend_noirq() method of the PM domain will use omap_device_idle()
to idle the HW after calling the driver's ->runtime_suspend()
callback. Similarily, upon resume, if the device was suspended during
->suspend_noirq(), the ->resume_noirq() method of the PM domain will
use omap_device_enable() to enable the HW and then call the driver's
->runtime_resume() callback.
If a device has already been runtime suspended, the noirq methods of
the PM domain leave the device runtime suspended by default.
However, if a driver needs to runtime resume a device during suspend
(for example, to change its wakeup settings), it may do so using
pm_runtime_get* in it's ->suspend() callback.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Only build and use the runtime PM helper functions only when runtime
PM is actually enabled.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
