There is missing "if defined" CONFIG_DRM_AMD_DC block for non DC
configurations. This will cause link error. The patch is fixing that.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=110979
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In renoir's vega10_ih model, there's a security change in mmIH_CHICKEN
register, that limits IH to use physical address (FBPA, GPA) directly.
Those chicken bits need to be programmed first.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This should be checked at all places job is accessed.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable DC support for renoir.
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Init SDMA HW base configuration and enable idle INT for rn.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix compute ring test failure in sriov scenario.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tianci.Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
stolen memory should be fixed in visible region.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tianci.Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a DRM_DEBUG_DRIVER debug message.
Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need to add new asic cases. This is a sw display
implementation, so just drop the error message so when
we add new asics, all we have to do is add the virtual
dce IP module.
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Comparing adev->family with CHIP constants is not correct.
adev->family can only be compared with AMDGPU_FAMILY constants and
adev->asic_type is the struct member to compare with CHIP constants.
They are separate identification spaces.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 62a3755341 ("drm/amdgpu: add si implementation v10")
Cc: Ken Wang <Qingqing.Wang@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The driver does not support these sensors yet and there is no point in
creating sysfs attributes which will always return an error.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: "David (ChunMing) Zhou" <David1.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
for SOC15/vega10 the BACO reset & mode1 would introduce vram lost
in high end address range, current kmd's vram lost checking cannot
catch it since it only check very ahead visible frame buffer
v2:
cover NV as well
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
in_suspend flag should be set in amdgpu_device_suspend/resume in pairs,
instead of gfx10 ip suspend/resume function.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For picasso(adev->pdev->device == 0x15d8)&raven2(adev->rev_id >= 0x8),
firmware is sufficient to support gfxoff.
In commit 98f58ada2d, for picasso&raven2,
return directly and cause gfxoff disabled.
Fixes: 98f58ada2d ("drm/amdgpu/gfx9: update pg_flags after determining if gfx off is possible")
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Needs ATPX rather than _PR3 to really turn off the dGPU. This can save
~5W when dGPU is runtime-suspended.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement HW I2C enigne controller to be used by the RAS EEPROM
table manager. This is based on code from ATITOOLs.
v2:
Rename the file and all function prefixes to smu_v11_0_i2c
By Luben's observation always fill the TX fifo to full so
we don't have garbadge interpreted by the slave as valid data.
v3:
Remove preemption disable as the HW I2C controller will not
stop the clock on empty TX fifo and so it's not critical to
keep not empty queue.
Switch to fast mode 400 khz SCL clock for faster read and write.
v5:
Restore clock gating before releasing I2C bus and fix some
style comments.
v6:
squash in warning fix, fix includes (Alex)
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Luben Tuikov <Luben.Tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add RAS EEPROM table manager to eanble RAS errors to be stored
upon appearance and retrived on driver load.
v2: Fix some prints.
v3:
Fix checksum calculation.
Make table record and header structs packed to do correct byte value sum.
Fix record crossing EEPROM page boundry.
v4:
Fix byte sum val calculation for record - look at sizeof(record).
Fix some style comments.
v5: Add description to EEPROM_TABLE_RECORD_SIZE and syntax fixes.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Luben Tuikov <Luben.Tuikov@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 4f8bc72fbf.
It turned out that a single reserved queue wouldn't be
sufficient for page fault handling.
Signed-off-by: Gang Ba <gaba@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The GRBM register interface is now capable of bursting 1 cycle per
register wr->wr, wr->rd much faster than previous muticycle per
transaction done interface. This has caused a problem where status
registers requiring HW to update have a 1 cycle delay, due to the
register update having to go through GRBM.
SW may operate on an incorrect value if they write a register and
immediately check the corresponding status register.
Registers requiring HW to clear or set fields may be delayed by 1 cycle.
For example,
1. write VM_INVALIDATE_ENG0_REQ mask = 5a
2. read VM_INVALIDATE_ENG0_ACK till the ack is same as the request mask = 5a
a. HW will reset VM_INVALIDATE_ENG0_ACK = 0 until invalidation is complete
3. write VM_INVALIDATE_ENG0_REQ mask = 5a
4. read VM_INVALIDATE_ENG0_ACK till the ack is same as the request mask = 5a
a. First read of VM_INVALIDATE_ENG0_ACK = 5a instead of 0
b. Second read of VM_INVALIDATE_ENG0_ACK = 0 because
the remote GRBM h/w register takes one extra cycle to be cleared
c. In this case, SW will see a false ACK if they exit on first read
Affected registers (only GC variant) | Recommended Dummy Read
--------------------------------------+----------------------------
VM_INVALIDATE_ENG*_ACK | VM_INVALIDATE_ENG*_REQ
VM_L2_STATUS | VM_L2_STATUS
VM_L2_PROTECTION_FAULT_STATUS | VM_L2_PROTECTION_FAULT_STATUS
VM_L2_PROTECTION_FAULT_ADDR_HI/LO32 | VM_L2_PROTECTION_FAULT_ADDR_HI/LO32
VM_L2_IH_LOG_BUSY | VM_L2_IH_LOG_BUSY
MC_VM_L2_PERFCOUNTER_HI/LO | MC_VM_L2_PERFCOUNTER_HI/LO
ATC_L2_PERFCOUNTER_HI/LO | ATC_L2_PERFCOUNTER_HI/LO
ATC_L2_PERFCOUNTER2_HI/LO | ATC_L2_PERFCOUNTER2_HI/LO
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that we properly handle them on older asics.
Fixes: 3ff985485b ("drm/amdgpu: Export function to flush TLB of specific vm hub")
Tested-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use unsigned long type for the same ras count variable.
This will avoid overflow on 64 bit system.
Signed-off-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This will enable indirect SRAM loading for VCN DPG mode initialization.
Signed-off-by: Thong Thai <thong.thai@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 444a0fea51.
We are ready to enable it now.
Signed-off-by: Thong Thai <thong.thai@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates gc/sdma goldensetting for renoir
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable SDMA PG flag during device ip early init.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for SDMA clockgating on RN.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable DF clock gating during DF IP early init.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable athub MG and LS clock gating.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable IH clock gating during IH block initialized.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch updates gfxoff feature.
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add set_gfx_cgpg implement
v2: check if using sw_smu (Alex)
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1.Implement PowerUpSDMA/PowerDownSDMA interfaces in the swSMU for renoir
2.adjust smu ip block ahead of gfx&sdma ip block
Signed-off-by: Aaron Liu <aaron.liu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
v2: set num_types based on num_instances
navi1x has 2 sdma engines but commit
"e7b58d03b678 drm/amdgpu: reorganize sdma v4 code to support more instances"
changes the max number of sdma irq types (AMDGPU_SDMA_IRQ_LAST) from 2 to 8
which causes amdgpu_irq_gpu_reset_resume_helper() to recover irq of sdma
engines with following logic:
(enable irq for sdma0) * 1 time
(enable irq for sdma1) * 1 time
(disable irq for sdma1) * 6 times
as a result, after gpu reset, interrupt for sdma1 is lost.
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to grab a reference to the fence we wait for.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
arcturus for sriov would use the unified mc base address
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Frank.Min <Frank.Min@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since agp is not used for sriov, just disable it
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Frank.Min <Frank.Min@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/amd/amdgpu/nv.c: In function 'nv_common_early_init':
drivers/gpu/drm/amd/amdgpu/nv.c:471:7: warning:
variable 'psp_enabled' set but not used [-Wunused-but-set-variable]
It's not used since inroduction in
commit c6b6a42175 ("drm/amdgpu: add navi10 common ip block (v3)")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
