VF changes unicast mac address by sending mailbox msg to PF, then PF
completes the mac address modification. It may fail when the target
uc mac address is already in the mac_vlan table. VF should be aware
of it by reading the message result.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not allowed to add two same unicast mac address entries to the
mac_vlan table. When modify the uc mac address of a VF device to the
same value with the PF device's, the PF device will lose its entry of
the mac_vlan table.
Lookup the mac address in the mac_vlan table, and add it if the entry
is inexistent.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Error code -EIO was used to indicate mutilple errors in function
hclge_get_mac_vlan_cmd_status().This patch fixes it by using
error code depending on the error type.
For no space error, return -ENOSPC.
For entry not found, return -ENOENT.
For command send fail, return -EIO.
For invalid op code, return -EINVAL.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An enum type variable was used to store an "int" type return value.
This patch fixes it.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the buffer overflow warning by refactoring
hclgevf_bind_ring_to_vector and hclge_get_ring_chain_from_mbx.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: dde1a86e93 ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vlan ctag filter is enabled, the loopback selftest fails because
loopback selftest does not support vlan.
This patch fixes it by disabling the vlan ctag filter when runnig
loopback selftest.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for querying pfc puase packets statistic
in hclge_ieee_getpfc, which is used to tell user how many pfc
puase packets have been sent and received by this mac port.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original skb->truesize reports the received packet size,
not the actual buffer size NIC driver allocated(1 Page).
The linux net protocol will misjudge the true size of rx queue.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the firmware cmd to setup mac pause params is the same as the
firmware cmd to pfc pause params, this patch unifies the pause params
setup function.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function of dev_close and dev_open is just likes ifconfig <netif> down
and ifconfig <netif> up. The ipv6 address will be lost after dev_close and
dev_open are called. This patch uses hns3_nic_net_stop to replace dev_close
and uses hns3_nic_net_open to replace dev_open.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status update function is called by timer every second. But
net_stop and net_open may be called with very short intervals. The link
status update function can not detect the link state has changed. It
causes the netdev not running problem.
This patch fixes it by updating the link state in ae_stop function.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver is in initial state, the mac_vlan table table is empty.
So the delete operation for mac address must fail. Existence check
is needed here. Otherwise, the error message will make user confused.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 cards can support up to 100 G speeds. So, increase
max programmable tx rate limit to 100 Gbps.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the coalesce configuation lost problem when
setting the channel number by restoring all vectors's coalesce
configuation to vector 0's, because all vectors belonging to
the same netdev have the same coalesce configuation for now.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refoctors the coalesce related struct by introducing
the hns3_enet_coalesce struct, in order to fix the coalesce
configuation lost problem when changing the channel number.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coalesce configuration will be set to default value by
hns3_nic_init_vector_data during reset, which causes the
coalesce configuration loss problem.
This patch fixes it by setting the default value in
hns3_nic_alloc_vector_data, which will not be called in the
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a get_vector function, which allocate the vectors
for a client, but there is not a put_vector to free the
vector.
This patch introduces the put_vector function in order to
fix the coalesce configuration lost problem during reset
process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hns3_set_ringparam, hns3_uninit_all_ring frees the
memory pointed by priv->ring_data[i].ring, and
hns3_change_all_ring_bd_num use that pointer without mallocing,
which will cause a use-after-free problem.
The patch fixes it by not freeing the memory in
hns3_uninit_all_ring, and uses hns3_put_ring_config to free it
when necessary.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pause configuration will be set to default value by hclge_tm_schd_init
during reset, which causes the RSS configuration loss problem.
This patch fixes it by calling hclge_tm_init_hw during reset process
, which will set the pause configuration to default value.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS configuration will be set to default value by hclge_rss_init_hw
during reset, which causes the RSS configuration loss problem.
This patch fixes it by setting the default value in
hclge_rss_init_cfg function, which will not be called in the reset
process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors the hclge_get/set_rss_tuple function
in order to fix the rss configuration loss problem during
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors the hclge_get/set_rss function in
order to fix the rss configuration loss problem during
reset process.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a linked list to associate user-facing context IDs with FW-facing
context IDs (since the latter can change after an MC reset).
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid doing useless work by making sure that the response_list is not empty
before scheduling work to process it.
Signed-off-by: Prasad Kanneganti <prasad.kanneganti@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Corrected length check when data received in the mbox is more than one
64 bit data value
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series follows our previous one to lay out the foundations for IPSec
in user-space and extend current kernel netdev IPSec support. As noted in
our previous pull request cover letter "mlx5-updates-2018-02-28-1 (IPSec-1)",
the IPSec mechanism will be supported through our flow steering mechanism.
Therefore, we need to change the initialization order. Furthermore, IPsec
is also supported in both egress and ingress. Since our current flow
steering is egress only, we add an empty (only implemented through FPGA
steering ops) egress namespace to handle that case. We also implement
the required flow steering callbacks and logic in our FPGA driver.
We extend the FPGA support for ESN and modifying a xfrm too. Therefore, we
add support for some new FPGA command interface that supports them. The
other required bits are added too. The new features and requirements are
advertised via cap bits.
Last but not least, we revise our driver's accel_esp API. This API will be
shared between our netdev and IB driver, so we need to have all the required
functionality from both worlds.
Regards,
Aviad and Matan
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaoH8zAAoJEEg/ir3gV/o+h00H/RyM1xoGCzJtvQAYEhNcEfvY
YJfaJSPvuuvS2Fvs8meUzjqQvKcmkMjmViD3Ujuzyh6Y36IcoPWlBojRDE2fpz2b
yRaK5CotcLpfDXchlLnH5ZZbOgO374866viCVoM4i2ls19Ml730piDs8CDcA6+T7
3W4vvr977xl9bFqDMMbeldijZ3+H36Exnq6Xj+o2j6Sc1/om9Mvgw7XJhcpiBTW5
ZFfA7djz7TdSyBJDQsLteL/wLbLsLeqXmKCKX9BsqRo+rpoUWmskKFNC1Dj0bzX3
XbrdR8GoHVMS1PZAPJIbc1bubhqBznxrbh/g95PInSkGZzKKWw1dhS/3fkkAndM=
=Fodq
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-02-28-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-02-28-2 (IPSec-2)
This series follows our previous one to lay out the foundations for IPSec
in user-space and extend current kernel netdev IPSec support. As noted in
our previous pull request cover letter "mlx5-updates-2018-02-28-1 (IPSec-1)",
the IPSec mechanism will be supported through our flow steering mechanism.
Therefore, we need to change the initialization order. Furthermore, IPsec
is also supported in both egress and ingress. Since our current flow
steering is egress only, we add an empty (only implemented through FPGA
steering ops) egress namespace to handle that case. We also implement
the required flow steering callbacks and logic in our FPGA driver.
We extend the FPGA support for ESN and modifying a xfrm too. Therefore, we
add support for some new FPGA command interface that supports them. The
other required bits are added too. The new features and requirements are
advertised via cap bits.
Last but not least, we revise our driver's accel_esp API. This API will be
shared between our netdev and IB driver, so we need to have all the required
functionality from both worlds.
Regards,
Aviad and Matan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
During a device failover or partition migration reset, it is not
necessary to disable the backing adapter since it should not be
running yet and its Command-Response Queue is closed. Sending
device commands during this time could result in an error or
timeout disrupting the reset process. In these cases, just halt
transmissions, clean up resources, and continue with reset.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a function to halt network operations and clean up any
unused or outstanding socket buffers. Then, during device close,
disable backing adapter before halting all queues and performing
cleanup. This ensures all backing device operations will be
stopped before the driver cleans up shared resources.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some dead code now that RX pools are being cleaned. This
was included to wait until any pending RX queue interrupts are
processed, but NAPI polling should be disabled by this point.
Another minor change is to use the net device parameter for any
print functions instead of accessing it from the adapter structure.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for VF driver inner interface
hclgevf_ops.get_tqps_and_rss_info. This interface will be
used in the initialization process.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 driver should alloc netdev with max support ring num, as
driver support change netdev count by ethtool -L.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command HCLGE_OPC_CFG_COM_TQP_QUEUE should use queue id in the
function, but command HCLGE_OPC_RESET_TQP_QUEUE should use global
queue id.
This patch fixes the queue id about queue enable/disable/reset.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the endian issue when PF get mbx message flag.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver check the out_vld bit when get a new cmdq BD, if the bit is 1,
the BD is valid. driver Should set the bit 0 after used and hw will
set the bit 1 if get a valid BD.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF driver should get the real rss_size which is assigned
by host PF, not rss_size_max.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ESN is not supported with IPSec device offload.
This patch adds ESN support to IPsec device offload.
Implementing new xfrm device operation to synchronize offloading device
ESN with xfrm received SN. New QP command to update SA state at the
following:
ESN 1 ESN 2 ESN 3
|-----------*-----------|-----------*-----------|-----------*
^ ^ ^ ^ ^ ^
^ - marks where QP command invoked to update the SA ESN state
machine.
| - marks the start of the ESN scope (0-2^32-1). At this point move SA
ESN overlap bit to zero and increment ESN.
* - marks the middle of the ESN scope (2^31). At this point move SA
ESN overlap bit to one.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
New function for getting driver internal sa entry from xfrm state.
All checks are done in one function.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In order to add a context to the FPGA, we need to get both the software
transform context (which includes the keys, etc) and the
source/destination IPs (which are included in the steering
rule). Therefore, we register new set of firmware like commands for
the FPGA. Each time a rule is added, the steering core infrastructure
calls the FPGA command layer. If the rule is intended for the FPGA,
it combines the IPs information with the software transformation
context and creates the respective hardware transform.
Afterwards, it calls the standard steering command layer.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code has one layer that executed FPGA commands and
the Ethernet part directly used this code. Since downstream patches
introduces support for IPSec in mlx5_ib, we need to provide some
abstractions. This patch refactors the accel code into one layer
that creates a software IPSec transformation and another one which
creates the actual hardware context.
The internal command implementation is now hidden in the FPGA
core layer. The code also adds the ability to share FPGA hardware
contexts. If two contexts are the same, only a reference count
is taken.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
This patch adds V2 command support.
New fpga devices support extended features (udp encap, esn etc...), this
features require new hardware sadb format therefore we have a new version
of commands to manipulate it.
Signed-off-by: Yossef Efraim <yossefe@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current hardware decrypts and authenticates incoming ESP packets.
Subsequently, the software extracts the nexthdr field, truncates the
trailer and adjusts csum accordingly.
With this patch and a capable device, the trailer is being removed
by the hardware and the nexthdr field is conveyed via PET. This way
we avoid both the need to access the trailer (cache miss) and to
compute its relative checksum, which significantly improve
the performance.
Experiment shows that trailer removal improves the performance by
2Gbps, (netperf). Both forwarding and host-to-host configurations.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current code assume only SA QP commands.
Refactor in order to pave the way for new QP commands:
1. Generic cmd response format.
2. SA cmd checks are in dedicated functions.
3. Aligned debug prints.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Fix build break of mlx5_accel_ipsec_device_caps is not defined when
MLX5_ACCEL is not selected, use MLX5_IPSEC_DEV instead which handles
such case.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reported-by: Doug Ledford <dledford@redhat.com>
Remove VLA usage and change the 'len' argument to a u8 and use a 256
byte buffer on the stack. Notice that these lengths are limited by the
encoding field in the VPD structure, which is a u8 [1].
[1] https://marc.info/?l=linux-netdev&m=152044354814024&w=2
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell PPv2 controller can be used to implement packet filtering based
on the destination MAC address. This is already used to implement
multicast filtering. This patch adds support for Unicast filtering.
Filtering is based on so-called "TCAM entries" to implement filtering.
Due to their limited number and the fact that these are also used for
other purposes, we reserve 80 entries for both unicast and multicast
filters. On top of the broadcast address, and each interface's own MAC
address, we reserve 25 entries per port, 4 for unicast filters, 21 for
multicast.
Whenever unicast or multicast range for one port is full, the filtering
is disabled and port goes into promiscuous mode for the given type of
addresses.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_prs_mac_da_accept function takes into parameter both the
struct representing the controller and the port id. This is meaningful
when we want to create TCAM entries for non-initialized ports, but in
this case we expect the port to be initialized before starting adding or
removing MAC addresses to the per-port filter.
This commit changes the function so that it takes struct mvpp2_port as
a parameter instead.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series consists of some fixes and refactors for the mlx5 drivers,
especially around the FPGA and flow steering. Most of them are trivial
fixes and are the foundation of allowing IPSec acceleration from user-space.
We use flow steering abstraction in order to accelerate IPSec packets.
When a user creates a steering rule, [s]he states that we'll carry an
encrypt/decrypt flow action (using a specific configuration) for every
packet which conforms to a certain match. Since currently offloading these
packets is done via FPGA, we'll add another set of flow steering ops.
These ops will execute the required FPGA commands and then call the
standard steering ops.
In order to achieve this, we need that the commands will get all the
required information. Therefore, we pass the fte object and embed the
flow_action struct inside the fte. In addition, we add the shim layer
that will later be used for alternating between the standard and the
FPGA steering commands.
Some fixes, like " net/mlx5e: Wait for FPGA command responses with a timeout"
are very relevant for user-space applications, as these applications could
be killed, but we still want to wait for the FPGA and update the kernel's
database.
Regards,
Aviad and Matan
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJan4UmAAoJEEg/ir3gV/o+cZwH/1xBpdLsmeqEimwQ41bAc9Rj
UmPZXXMyQVUYfGOiE1aLTH7YNi38XWSnTFMN7HklMeX/9YKxUZNG8YuiO9iQhE1B
rUqRKfYFz9oFrUh95SzeclaunTpKrhYKHjQ9/u9nBMfI3H2Fy+y2NUBjIqJ6nysz
op3EwRcX5kD4+MjRum24XLUnMSYbg05mHCZKTDj5/2T4x+/j0XQqvvmWWinIt8BO
R4d7XGGywGjbhtcG1j+XBcFeLsEZnS/w70hoN38TdcmNWvokl1pGk8DVDii9i7GX
c5jQj2h5WG/bdsS26y8MFfWpoAn3Qzzm4W4OYwp/vmL7n/Llvq0GRCEKCi8AlA0=
=LeYV
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2018-02-28-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Saeed Mahameed says:
====================
mlx5-updates-2018-02-28-1 (IPSec-1)
This series consists of some fixes and refactors for the mlx5 drivers,
especially around the FPGA and flow steering. Most of them are trivial
fixes and are the foundation of allowing IPSec acceleration from user-space.
We use flow steering abstraction in order to accelerate IPSec packets.
When a user creates a steering rule, [s]he states that we'll carry an
encrypt/decrypt flow action (using a specific configuration) for every
packet which conforms to a certain match. Since currently offloading these
packets is done via FPGA, we'll add another set of flow steering ops.
These ops will execute the required FPGA commands and then call the
standard steering ops.
In order to achieve this, we need that the commands will get all the
required information. Therefore, we pass the fte object and embed the
flow_action struct inside the fte. In addition, we add the shim layer
that will later be used for alternating between the standard and the
FPGA steering commands.
Some fixes, like " net/mlx5e: Wait for FPGA command responses with a timeout"
are very relevant for user-space applications, as these applications could
be killed, but we still want to wait for the FPGA and update the kernel's
database.
Regards,
Aviad and Matan
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
