[ Upstream commit 11fc79fc9f2e395aa39fa5baccae62767c5d8280 ]
When calling xsk_socket__create_shared(), the logic at line 1097 marks a
boolean flag true within the xsk_umem structure to track setup progress
in order to support multiple calls to the function. However, instead of
marking umem->tx_ring_setup_done, the code incorrectly sets
umem->rx_ring_setup_done. This leads to improper behaviour when
creating and destroying xsk and umem structures.
Multiple calls to this function is documented as supported.
Fixes: ca7a83e2487a ("libbpf: Only create rx and tx XDP rings when necessary")
Signed-off-by: Kev Jackson <foamdino@gmail.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/YL4aU4f3Aaik7CN0@linux-dev
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 197eecb6ecae0b04bd694432f640ff75597fed9c ]
When peeking an event, it has a short path and a long path. The short
path uses the session pointer "one_mmap_addr" to directly fetch the
event; and the long path needs to read out the event header and the
following event data from file and fill into the buffer pointer passed
through the argument "buf".
The issue is in the long path that it copies the event header and event
data into the same destination address which pointer "buf", this means
the event header is overwritten. We are just lucky to run into the
short path in most cases, so we don't hit the issue in the long path.
This patch adds the offset "hdr_sz" to the pointer "buf" when copying
the event data, so that it can reserve the event header which can be
used properly by its caller.
Fixes: 5a52f33adf ("perf session: Add perf_session__peek_event()")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210605052957.1070720-1-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit e8ba0b2b64126381643bb50df3556b139a60545a upstream.
Fix to return a negative error code from the error handling case instead
of 0, as done elsewhere in this function.
Link: https://lkml.kernel.org/r/20210508034216.2277-1-thunder.leizhen@huawei.com
Fixes: a995e6bc05 ("tools/bootconfig: Fix to check the write failure correctly")
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8873d11d4121aad35024f9379e431e0c83abead upstream.
Some distros may enable strict rp_filter by default, which will prevent
vethc from receiving the packets with an unrouteable reverse path address.
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit acf2492b51c9a3c4dfb947f4d3477a86d315150f upstream.
On recent kernels, this config symbol is no longer used.
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fixes: e7096c131e ("net: WireGuard secure network tunnel")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3cb17cce1e76ccc5499915a4d7e095a1ad6bf7ff ]
If we just check whether the variable can be converted, 'tvar' should be
a null pointer. However, the null pointer check is missing in the
'Constant value' execution path.
The following cases can trigger this problem:
$ cat test.c
#include <stdio.h>
void main(void)
{
int a;
const int b = 1;
asm volatile("mov %1, %0" : "=r"(a): "i"(b));
printf("a: %d\n", a);
}
$ gcc test.c -o test -O -g
$ sudo ./perf probe -x ./test -L "main"
<main@/home/lhf/test.c:0>
0 void main(void)
{
2 int a;
const int b = 1;
asm volatile("mov %1, %0" : "=r"(a): "i"(b));
6 printf("a: %d\n", a);
}
$ sudo ./perf probe -x ./test -V "main:6"
Segmentation fault
The check on 'tvar' is added. If 'tavr' is a null pointer, we return 0
to indicate that the variable can be converted. Now, we can successfully
show the variables that can be accessed.
$ sudo ./perf probe -x ./test -V "main:6"
Available variables at main:6
@<main+13>
char* __fmt
int a
int b
However, the variable 'b' cannot be tracked.
$ sudo ./perf probe -x ./test -D "main:6 b"
Failed to find the location of the 'b' variable at this address.
Perhaps it has been optimized out.
Use -V with the --range option to show 'b' location range.
Error: Failed to add events.
This is because __die_find_variable_cb() did not successfully match
variable 'b', which has the DW_AT_const_value attribute instead of
DW_AT_location. We added support for DW_AT_const_value in
__die_find_variable_cb(). With this modification, we can successfully
track the variable 'b'.
$ sudo ./perf probe -x ./test -D "main:6 b"
p:probe_test/main_L6 /home/lhf/test:0x1156 b=\1:s32
Fixes: 66f69b2197 ("perf probe: Support DW_AT_const_value constant value")
Signed-off-by: Li Huafei <lihuafei1@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Frank Ch. Eigler <fche@redhat.com>
Cc: Jianlin Lv <jianlin.lv@arm.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: Yang Jihong <yangjihong1@huawei.com>
Cc: Zhang Jinhao <zhangjinhao2@huawei.com>
http://lore.kernel.org/lkml/20210601092750.169601-1-lihuafei1@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a8deba8547e39f26440101164a3bbc2899c5b305 upstream.
The help information was not added at the time when the function got added.
Fix this and add the missing information to its cli, documentation and bash
completion.
Fixes: db94cc0b48 ("bpftool: Add support for BPF_CGROUP_INET_SOCK_RELEASE")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Quentin Monnet <quentin@isovalent.com>
Link: https://lore.kernel.org/bpf/20210525014139.323859-1-liujian56@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f747e6667ebb2ffb8133486c9cd19800d72b0d98 ]
GENMASK() has an input check which uses __builtin_choose_expr() to
enable a compile time sanity check of its inputs if they are known at
compile time.
However, it turns out that __builtin_constant_p() does not always return
a compile time constant [0]. It was thought this problem was fixed with
gcc 4.9 [1], but apparently this is not the case [2].
Switch to use __is_constexpr() instead which always returns a compile time
constant, regardless of its inputs.
Link: https://lore.kernel.org/lkml/42b4342b-aefc-a16a-0d43-9f9c0d63ba7a@rasmusvillemoes.dk [0]
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=19449 [1]
Link: https://lore.kernel.org/lkml/1ac7bbc2-45d9-26ed-0b33-bf382b8d858b@I-love.SAKURA.ne.jp [2]
Link: https://lkml.kernel.org/r/20210511203716.117010-1-rikard.falkeborn@gmail.com
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Yury Norov <yury.norov@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 75ea44e356b5de8c817f821c9dd68ae329e82add upstream.
On some hosts, rlim.rlim_max can be returned as RLIM_INFINITY.
By casting it to int, it is interpreted as -1, which will cause get_maxfds
to return 0, causing "Invalid argument" errors in nftw() calls.
Fix this by casting the second argument of min() to rlim_t instead.
Fixes: 80eeb67fe5 ("perf jevents: Program to convert JSON file")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: http://lore.kernel.org/lkml/20210525160758.97829-1-nbd@nbd.name
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b68c1c65dec5fb5186ebd33ce52059b4c6db8500 ]
Currently the gpio selftests fail to build if the source tree is read
only:
make -j 160 -C tools/testing/selftests TARGETS=gpio
make[1]: Entering directory '/linux/tools/testing/selftests/gpio'
make OUTPUT=/linux/tools/gpio/ -C /linux/tools/gpio
make[2]: Entering directory '/linux/tools/gpio'
mkdir -p /linux/tools/gpio/include/linux 2>&1 || true
ln -sf /linux/tools/gpio/../../include/uapi/linux/gpio.h /linux/tools/gpio/include/linux/gpio.h
ln: failed to create symbolic link '/linux/tools/gpio/include/linux/gpio.h': Read-only file system
This happens because we ask make to build ../../../gpio (tools/gpio)
without pointing OUTPUT away from the source directory.
To fix it we create a subdirectory of the existing OUTPUT directory,
called tools-gpio, and tell tools/gpio to build in there.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 449539da2e237336bc750b41f1736a77f9aca25c ]
Move the include of lib.mk up so that in a subsequent patch we can use
OUTPUT, which is initialised by lib.mk, in the definition of the GPIO
variables.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff2c395b9257f0e617f9cd212893f3c72c80ee6c ]
Use TEST_GEN_PROGS_EXTENDED rather than TEST_PROGS_EXTENDED.
That tells the lib.mk logic that the files it references are to be
generated by the Makefile.
Having done that we don't need to override the all rule.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3a62fed2fd7b6fea96d720e779cafc30dfb3a22e upstream.
the patch that fixed an endless loop in_fq_pie_init() was not considering
that 65535 is a valid class id. The correct bugfix for this infinite loop
is to change 'idx' to become an u32, like Colin proposed in the past [1].
Fix this as follows:
- restore 65536 as maximum possible values of 'flows_cnt'
- use u32 'idx' when iterating on 'q->flows'
- fix the TDC selftest
This reverts commit bb2f930d6d.
[1] https://lore.kernel.org/netdev/20210407163808.499027-1-colin.king@canonical.com/
CC: Colin Ian King <colin.king@canonical.com>
CC: stable@vger.kernel.org
Fixes: bb2f930d6d ("net/sched: fix infinite loop in sch_fq_pie")
Fixes: ec97ecf1eb ("net: sched: add Flow Queue PIE packet scheduler")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f56299a9c998e0bfbd4ab07cafe9eb8444512448 upstream.
Deprecation warnings are useful only for the developer, not an end user.
Display warnings only when requested using the python -W option. This
stops the display of warnings like:
tools/perf/scripts/python/exported-sql-viewer.py:5102: DeprecationWarning:
an integer is required (got type PySide2.QtCore.Qt.AlignmentFlag).
Implicit conversion to integers using __int__ is deprecated, and
may be removed in a future version of Python.
err = app.exec_()
Since the warning can be fixed only in PySide2, we must wait for it to
be finally fixed there.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org # v5.3+
Link: http://lore.kernel.org/lkml/20210521092053.25683-4-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd931b2e234a7cc451a7bbb1965d6ce623189158 upstream.
The 'Array' class is present in more than one python standard library.
In some versions of Python 3, the following error occurs:
Traceback (most recent call last):
File "tools/perf/scripts/python/exported-sql-viewer.py", line 4702, in <lambda>
reports_menu.addAction(CreateAction(label, "Create a new window displaying branch events", lambda a=None,x=dbid: self.NewBranchView(x), self))
File "tools/perf/scripts/python/exported-sql-viewer.py", line 4727, in NewBranchView
BranchWindow(self.glb, event_id, ReportVars(), self)
File "tools/perf/scripts/python/exported-sql-viewer.py", line 3208, in __init__
self.model = LookupCreateModel(model_name, lambda: BranchModel(glb, event_id, report_vars.where_clause))
File "tools/perf/scripts/python/exported-sql-viewer.py", line 343, in LookupCreateModel
model = create_fn()
File "tools/perf/scripts/python/exported-sql-viewer.py", line 3208, in <lambda>
self.model = LookupCreateModel(model_name, lambda: BranchModel(glb, event_id, report_vars.where_clause))
File "tools/perf/scripts/python/exported-sql-viewer.py", line 3124, in __init__
self.fetcher = SQLFetcher(glb, sql, prep, self.AddSample)
File "tools/perf/scripts/python/exported-sql-viewer.py", line 2658, in __init__
self.buffer = Array(c_char, self.buffer_size, lock=False)
TypeError: abstract class
This apparently happens because Python can be inconsistent about which
class of the name 'Array' gets imported. Fix by importing explicitly by
name so that only the desired 'Array' gets imported.
Fixes: 8392b74b57 ("perf scripts python: exported-sql-viewer.py: Add ability to display all the database tables")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20210521092053.25683-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a6172059758ba1b496ae024cece7d5bdc8d017db upstream.
Provide missing argument to prevent following error when copying a
selection to the clipboard:
Traceback (most recent call last):
File "tools/perf/scripts/python/exported-sql-viewer.py", line 4041, in <lambda>
menu.addAction(CreateAction("&Copy selection", "Copy to clipboard", lambda: CopyCellsToClipboardHdr(self.view), self.view))
File "tools/perf/scripts/python/exported-sql-viewer.py", line 4021, in CopyCellsToClipboardHdr
CopyCellsToClipboard(view, False, True)
File "tools/perf/scripts/python/exported-sql-viewer.py", line 4018, in CopyCellsToClipboard
view.CopyCellsToClipboard(view, as_csv, with_hdr)
File "tools/perf/scripts/python/exported-sql-viewer.py", line 3871, in CopyTableCellsToClipboard
val = model.headerData(col, Qt.Horizontal)
TypeError: headerData() missing 1 required positional argument: 'role'
Fixes: 96c43b9a7a ("perf scripts python: exported-sql-viewer.py: Add copy to clipboard")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20210521092053.25683-2-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c954eb72b31a9dc56c99b450253ec5b121add320 upstream.
The decoder reports the current instruction if it was decoded. In some
cases the current instruction is not decoded, in which case the instruction
bytes length must be set to zero. Ensure that is always done.
Note perf script can anyway get the instruction bytes for any samples where
they are not present.
Also note, that there is a redundant "ptq->insn_len = 0" statement which is
not removed until a subsequent patch in order to make this patch apply
cleanly to stable branches.
Example:
A machne that supports TSX is required. It will have flag "rtm". Kernel
parameter tsx=on may be required.
# for w in `cat /proc/cpuinfo | grep -m1 flags `;do echo $w | grep rtm ; done
rtm
Test program:
#include <stdio.h>
#include <immintrin.h>
int main()
{
int x = 0;
if (_xbegin() == _XBEGIN_STARTED) {
x = 1;
_xabort(1);
} else {
printf("x = %d\n", x);
}
return 0;
}
Compile with -mrtm i.e.
gcc -Wall -Wextra -mrtm xabort.c -o xabort
Record:
perf record -e intel_pt/cyc/u --filter 'filter main @ ./xabort' ./xabort
Before:
# perf script --itrace=xe -F+flags,+insn,-period --xed --ns
xabort 1478 [007] 92161.431348581: transactions: x 400b81 main+0x14 (/root/xabort) mov $0xffffffff, %eax
xabort 1478 [007] 92161.431348624: transactions: tx abrt 400b93 main+0x26 (/root/xabort) mov $0xffffffff, %eax
After:
# perf script --itrace=xe -F+flags,+insn,-period --xed --ns
xabort 1478 [007] 92161.431348581: transactions: x 400b81 main+0x14 (/root/xabort) xbegin 0x6
xabort 1478 [007] 92161.431348624: transactions: tx abrt 400b93 main+0x26 (/root/xabort) xabort $0x1
Fixes: faaa87680b ("perf intel-pt/bts: Report instruction bytes and length in sample")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: stable@vger.kernel.org
Link: http://lore.kernel.org/lkml/20210519074515.9262-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e1481445407b86a483616c4542ffdc810efb680 upstream.
When locating the DWARF module for a given address, __find_debuginfo()
requires a 'struct dso' passed via the userdata argument.
However, this field is only set in __report_module() if the module is
found in via dwfl_addrmodule(), not if it is found later via
dwfl_report_elf().
Set userdata irrespective of how the DWARF module was found, as long as
we found a module.
Fixes: bf53fc6b5f41 ("perf unwind: Fix separate debug info files when using elfutils' libdw's unwinder")
Signed-off-by: Dave Rigby <d.rigby@me.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=211801
Acked-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Link: https://lore.kernel.org/linux-perf-users/20210218165654.36604-1-d.rigby@me.com/
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "Tommi Rantala" <tommi.t.rantala@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf53fc6b5f415cddc7118091cb8fd6a211b2320d upstream.
elfutils needs to be provided main binary and separate debug info file
respectively. Providing separate debug info file instead of the main
binary is not sufficient.
One needs to try both supplied filename and its possible cache by its
build-id depending on the use case.
Signed-off-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "Tommi Rantala" <tommi.t.rantala@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5665bc35c1ed917ac8fd06cb651317bb47a65b10 upstream.
The sc and scv 0 system calls have different ABI conventions, and
ptracers need to know which system call type is being used if they want
to look at the syscall registers.
Document that pt_regs.trap can be used for this, and fix one in-tree user
to work with scv 0 syscalls.
Fixes: 7fa95f9ada ("powerpc/64s: system call support for scv/rfscv instructions")
Cc: stable@vger.kernel.org # v5.9+
Reported-by: "Dmitry V. Levin" <ldv@altlinux.org>
Suggested-by: "Dmitry V. Levin" <ldv@altlinux.org>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210520111931.2597127-1-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d1cd3b2c5c1c32826454de3a18c6183238d47ed ]
Fix the link error by adding '-static':
gcc -Wall -Wl,-z,max-page-size=0x1000 -pie load_address.c -o /home/yang/linux/tools/testing/selftests/exec/load_address_4096
/usr/bin/ld: /tmp/ccopEGun.o: relocation R_AARCH64_ADR_PREL_PG_HI21 against symbol `stderr@@GLIBC_2.17' which may bind externally can not be used when making a shared object; recompile with -fPIC
/usr/bin/ld: /tmp/ccopEGun.o(.text+0x158): unresolvable R_AARCH64_ADR_PREL_PG_HI21 relocation against symbol `stderr@@GLIBC_2.17'
/usr/bin/ld: final link failed: bad value
collect2: error: ld returned 1 exit status
make: *** [Makefile:25: tools/testing/selftests/exec/load_address_4096] Error 1
Link: https://lkml.kernel.org/r/20210514092422.2367367-1-yangyingliang@huawei.com
Fixes: 206e22f019 ("tools/testing/selftests: add self-test for verifying load alignment")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Cc: Chris Kennelly <ckennelly@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c25ce589dca10d64dde139ae093abc258a32869c upstream.
Change every shebang which does not need an argument to use /usr/bin/env.
This is needed as not every distro has everything under /usr/bin,
sometimes not even bash.
Signed-off-by: Finn Behrens <me@kloenk.de>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad1237c30d975535a669746496cbed136aa5a045 ]
Justin reported broken build with LIBBPF_DYNAMIC=1.
When linking libbpf dynamically we need to use perf's
hashmap object, because it's not exported in libbpf.so
(only in libbpf.a).
Following build is now passing:
$ make LIBBPF_DYNAMIC=1
BUILD: Doing 'make -j8' parallel build
...
$ ldd perf | grep libbpf
libbpf.so.0 => /lib64/libbpf.so.0 (0x00007fa7630db000)
Fixes: eee1950192 ("perf tools: Grab a copy of libbpf's hashmap")
Reported-by: Justin M. Forbes <jforbes@redhat.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/20210508205020.617984-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a30f9440640c418bcfbea9b2b344d268b58e0a2 ]
One of our benchmarks running in (Google-internal) CI pushes data
through the ringbuf faster htan than userspace is able to consume
it. In this case it seems we're actually able to get >INT_MAX entries
in a single ring_buffer__consume() call. ASAN detected that cnt
overflows in this case.
Fix by using 64-bit counter internally and then capping the result to
INT_MAX before converting to the int return type. Do the same for
the ring_buffer__poll().
Fixes: bf99c936f9 (libbpf: Add BPF ring buffer support)
Signed-off-by: Brendan Jackman <jackmanb@google.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210429130510.1621665-1-jackmanb@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1233898ab758cbcf5f6fea10b8dd16a0b2c24fab ]
The mirror_gre_scale test creates as many ERSPAN sessions as the underlying
chip supports, and tests that they all work. In order to determine that it
issues a stream of ICMP packets and checks if they are mirrored as
expected.
However, the mausezahn invocation missed the -6 flag to identify the use of
IPv6 protocol, and was sending ICMP messages over IPv6, as opposed to
ICMP6. It also didn't pass an explicit source IP address, which apparently
worked at some point in the past, but does not anymore.
To fix these issues, extend the function mirror_test() in mirror_lib by
detecting the IPv6 protocol addresses, and using a different ICMP scheme.
Fix __mirror_gre_test() in the selftest itself to pass a source IP address.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dda7f4fa55839baeb72ae040aeaf9ccf89d3e416 ]
The intention behind this test is to make sure that qdisc limit is
correctly projected to the HW. However, first, due to rounding in the
qdisc, and then in the driver, the number cannot actually be accurate. And
second, the approach to testing this is to oversubscribe the port with
traffic generated on the same switch. The actual backlog size therefore
fluctuates.
In practice, this test proved to be noisier than the rest, and spuriously
fails every now and then. Increase the tolerance to 10 % to avoid these
issues.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Acked-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 26e6dd1072763cd5696b75994c03982dde952ad9 ]
selftests/bpf/Makefile includes lib.mk. With the following command
make -j60 LLVM=1 LLVM_IAS=1 <=== compile kernel
make -j60 -C tools/testing/selftests/bpf LLVM=1 LLVM_IAS=1 V=1
some files are still compiled with gcc. This patch
fixed lib.mk issue which sets CC to gcc in all cases.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210413153413.3027426-1-yhs@fb.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a72c94ebfb1f171eba0715998010678a09ec796 ]
The rfi_flush and entry_flush selftests work by using the PM_LD_MISS_L1
perf event to count L1D misses. The value of this event has changed
over time:
- Power7 uses 0x400f0
- Power8 and Power9 use both 0x400f0 and 0x3e054
- Power10 uses only 0x3e054
Rather than relying on raw values, configure perf to count L1D read
misses in the most explicit way available.
This fixes the selftests to work on systems without 0x400f0 as
PM_LD_MISS_L1, and should change no behaviour for systems that the tests
already worked on.
The only potential downside is that referring to a specific perf event
requires PMU support implemented in the kernel for that platform.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Acked-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20210223070227.2916871-1-ruscur@russell.cc
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 050ffc449008eeeafc187dec337d9cf1518f89bc ]
Since commit d110162caf ("perf tsc: Support cap_user_time_short for
event TIME_CONV"), the event PERF_RECORD_TIME_CONV has extended the data
structure for clock parameters.
To be backwards-compatible, this patch adds a dedicated swap operation
for the event PERF_RECORD_TIME_CONV, based on checking if the event
contains field "time_cycles", it can support both for the old and new
event formats.
Fixes: d110162caf ("perf tsc: Support cap_user_time_short for event TIME_CONV")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steve MacLean <Steve.MacLean@Microsoft.com>
Cc: Yonatan Goldschmidt <yonatan.goldschmidt@granulate.io>
Link: https://lore.kernel.org/r/20210428120915.7123-4-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa616f5a8a2d22a179d5502ebd85045af66fa656 ]
Commit d110162caf ("perf tsc: Support cap_user_time_short for
event TIME_CONV") supports the extended parameters for event TIME_CONV,
but it broke the backwards compatibility, so any perf data file with old
event format fails to convert timestamp.
This patch introduces a helper event_contains() to check if an event
contains a specific member or not. For the backwards-compatibility, if
the event size confirms the extended parameters are supported in the
event TIME_CONV, then copies these parameters.
Committer notes:
To make this compiler backwards compatible add this patch:
- struct perf_tsc_conversion tc = { 0 };
+ struct perf_tsc_conversion tc = { .time_shift = 0, };
Fixes: d110162caf ("perf tsc: Support cap_user_time_short for event TIME_CONV")
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steve MacLean <Steve.MacLean@Microsoft.com>
Cc: Yonatan Goldschmidt <yonatan.goldschmidt@granulate.io>
Link: https://lore.kernel.org/r/20210428120915.7123-3-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1d380ea8b00db4bb14d1f513000d4b62aa9d3f0 ]
C standard claims "An object declared as type _Bool is large enough to
store the values 0 and 1", bool type size can be 1 byte or larger than
1 byte. Thus it's uncertian for bool type size with different
compilers.
This patch changes the bool type in structure perf_record_time_conv to
__u8 type, and pads extra bytes for 8-byte alignment; this can give
reliable structure size.
Fixes: d110162caf ("perf tsc: Support cap_user_time_short for event TIME_CONV")
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Gustavo A. R. Silva <gustavoars@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steve MacLean <Steve.MacLean@Microsoft.com>
Cc: Yonatan Goldschmidt <yonatan.goldschmidt@granulate.io>
Link: https://lore.kernel.org/r/20210428120915.7123-2-leo.yan@linaro.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 10bf4e83167cc68595b85fd73bb91e8f2c086e36 ]
Similarly as b02709587e ("bpf: Fix propagation of 32-bit signed bounds
from 64-bit bounds."), we also need to fix the propagation of 32 bit
unsigned bounds from 64 bit counterparts. That is, really only set the
u32_{min,max}_value when /both/ {umin,umax}_value safely fit in 32 bit
space. For example, the register with a umin_value == 1 does /not/ imply
that u32_min_value is also equal to 1, since umax_value could be much
larger than 32 bit subregister can hold, and thus u32_min_value is in
the interval [0,1] instead.
Before fix, invalid tracking result of R2_w=inv1:
[...]
5: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0) R10=fp0
5: (35) if r2 >= 0x1 goto pc+1
[...] // goto path
7: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,umin_value=1) R10=fp0
7: (b6) if w2 <= 0x1 goto pc+1
[...] // goto path
9: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,smin_value=-9223372036854775807,smax_value=9223372032559808513,umin_value=1,umax_value=18446744069414584321,var_off=(0x1; 0xffffffff00000000),s32_min_value=1,s32_max_value=1,u32_max_value=1) R10=fp0
9: (bc) w2 = w2
10: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv1 R10=fp0
[...]
After fix, correct tracking result of R2_w=inv(id=0,umax_value=1,var_off=(0x0; 0x1)):
[...]
5: R0_w=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0) R10=fp0
5: (35) if r2 >= 0x1 goto pc+1
[...] // goto path
7: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,umin_value=1) R10=fp0
7: (b6) if w2 <= 0x1 goto pc+1
[...] // goto path
9: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2=inv(id=0,smax_value=9223372032559808513,umax_value=18446744069414584321,var_off=(0x0; 0xffffffff00000001),s32_min_value=0,s32_max_value=1,u32_max_value=1) R10=fp0
9: (bc) w2 = w2
10: R0=inv1337 R1=ctx(id=0,off=0,imm=0) R2_w=inv(id=0,umax_value=1,var_off=(0x0; 0x1)) R10=fp0
[...]
Thus, same issue as in b02709587e holds for unsigned subregister tracking.
Also, align __reg64_bound_u32() similarly to __reg64_bound_s32() as done in
b02709587e to make them uniform again.
Fixes: 3f50f132d8 ("bpf: Verifier, do explicit ALU32 bounds tracking")
Reported-by: Manfred Paul (@_manfp)
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bede0ebf0be87e9678103486a77f39e0334c6791 ]
Fix failed tests checks in core_reloc test runner, which allowed failing tests
to pass quietly. Also add extra check to make sure that expected to fail test cases with
invalid names are caught as test failure anyway, as this is not an expected
failure mode. Also fix mislabeled probed vs direct bitfield test cases.
Fixes: 124a892d1c ("selftests/bpf: Test TYPE_EXISTS and TYPE_SIZE CO-RE relocations")
Reported-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/20210426192949.416837-6-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a30eb23922b52f33222c6729b6b3ff1c37a6c66 ]
Negative field existence cases for have a broken assumption that FIELD_EXISTS
CO-RE relo will fail for fields that match the name but have incompatible type
signature. That's not how CO-RE relocations generally behave. Types and fields
that match by name but not by expected type are treated as non-matching
candidates and are skipped. Error later is reported if no matching candidate
was found. That's what happens for most relocations, but existence relocations
(FIELD_EXISTS and TYPE_EXISTS) are more permissive and they are designed to
return 0 or 1, depending if a match is found. This allows to handle
name-conflicting but incompatible types in BPF code easily. Combined with
___flavor suffixes, it's possible to handle pretty much any structural type
changes in kernel within the compiled once BPF source code.
So, long story short, negative field existence test cases are invalid in their
assumptions, so this patch reworks them into a single consolidated positive
case that doesn't match any of the fields.
Fixes: c7566a6969 ("selftests/bpf: Add field existence CO-RE relocs tests")
Reported-by: Lorenz Bauer <lmb@cloudflare.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/20210426192949.416837-5-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f1c92139e36223b89d8140f2b72f75e79baf8bd ]
Currently, the error return code of the failure condition is lost after
using an if statement, so the test doesn't fail when it should.
Remove the if statement that separates the condition and the error code
check, so the test won't always pass.
Fixes: abfce9e062 ("selftests: mlxsw: Reduce running time using offload indication")
Reported-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c8d0260cdd96fdccdef0509c4160e28a1012a5d7 ]
The FDB roaming test installs a destination MAC address on the wrong
interface of an FDB database and tests whether the mirroring fails, because
packets are sent to the wrong port. The test by mistake installs the FDB
entry as local. This worked previously, because drivers were notified of
local FDB entries in the same way as of static entries. However that has
been fixed in the commit 6ab4c3117aec ("net: bridge: don't notify switchdev
for local FDB addresses"), and local entries are not notified anymore. As a
result, the HW is not reconfigured for the FDB roam, and mirroring keeps
working, failing the test.
To fix the issue, mark the FDB entry as static.
Fixes: 9c7c8a8244 ("selftests: forwarding: mirror_gre_vlan_bridge_1q: Add more tests")
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 83cd92b46484aa8f64cdc0bff8ac6940d1f78519 ]
When initializing the __param array with a one liner, if all args are
const, the initial array value will be placed in the rodata section but
because libbpf does not support relocation in the rodata section, any
pointer in this array will stay NULL.
Fixes: c09add2fbc ("tools/libbpf: Add bpf_iter support")
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210419155243.1632274-5-revest@chromium.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 86c2bc3da769124e3e856b6e9457be3667c30919 ]
Commit 08ed77e414 ("perf vendor events amd: Add recommended events")
added the hits event "L2 Cache Hits from L2 HWPF" with the same metric
expression as the accesses event "L2 Cache Accesses from L2 HWPF":
$ perf list --details
...
l2_cache_accesses_from_l2_hwpf
[L2 Cache Accesses from L2 HWPF]
[l2_pf_hit_l2 + l2_pf_miss_l2_hit_l3 + l2_pf_miss_l2_l3]
l2_cache_hits_from_l2_hwpf
[L2 Cache Hits from L2 HWPF]
[l2_pf_hit_l2 + l2_pf_miss_l2_hit_l3 + l2_pf_miss_l2_l3]
...
This was wrong and led to counting hits the same as accesses. Section
2.1.15.2 "Performance Measurement" of "PPR for AMD Family 17h Model 31h
B0 - 55803 Rev 0.54 - Sep 12, 2019", documents the hits event with
EventCode 0x70 which is the same as l2_pf_hit_l2.
Fix this, and massage the description for l2_pf_hit_l2 as the hits event
is now the duplicate of l2_pf_hit_l2. AMD recommends using the recommended
event over other events if the duplicate exists and maintain both for
consistency. Hence, l2_cache_hits_from_l2_hwpf should override
l2_pf_hit_l2.
Before:
# perf stat -M l2_cache_accesses_from_l2_hwpf,l2_cache_hits_from_l2_hwpf sleep 1
Performance counter stats for 'sleep 1':
1,436 l2_pf_miss_l2_l3 # 11114.00 l2_cache_accesses_from_l2_hwpf
# 11114.00 l2_cache_hits_from_l2_hwpf
4,482 l2_pf_hit_l2
5,196 l2_pf_miss_l2_hit_l3
1.001765339 seconds time elapsed
After:
# perf stat -M l2_cache_accesses_from_l2_hwpf sleep 1
Performance counter stats for 'sleep 1':
1,477 l2_pf_miss_l2_l3 # 10442.00 l2_cache_accesses_from_l2_hwpf
3,978 l2_pf_hit_l2
4,987 l2_pf_miss_l2_hit_l3
1.001491186 seconds time elapsed
# perf stat -e l2_cache_hits_from_l2_hwpf sleep 1
Performance counter stats for 'sleep 1':
3,983 l2_cache_hits_from_l2_hwpf
1.001329970 seconds time elapsed
Note the difference in performance counter values for the accesses
versus the hits after the fix, and the hits event now counting the same
as l2_pf_hit_l2.
Fixes: 08ed77e414 ("perf vendor events amd: Add recommended events")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206537
Reviewed-by: Robert Richter <rrichter@amd.com>
Signed-off-by: Smita Koralahalli <Smita.KoralahalliChannabasappa@amd.com>
Tested-by: Arnaldo Carvalho de Melo <acme@kernel.org> # On a 3900X
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kim Phillips <kim.phillips@amd.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Martin Liška <mliska@suse.cz>
Cc: Michael Petlan <mpetlan@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Vijay Thakkar <vijaythakkar@me.com>
Cc: linux-perf-users@vger.kernel.org
Link: https://lore.kernel.org/r/20210406215944.113332-2-Smita.KoralahalliChannabasappa@amd.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ea24b19562fe5f72c78319dbb347b701818956d9 ]
Similar to
https://lore.kernel.org/bpf/20210313210920.1959628-2-andrii@kernel.org/
When DECLARE_LIBBPF_OPTS is used with inline field initialization, e.g:
DECLARE_LIBBPF_OPTS(btf_dump_emit_type_decl_opts, opts,
.field_name = var_ident,
.indent_level = 2,
.strip_mods = strip_mods,
);
and compiled in debug mode, the compiler generates code which
leaves the padding uninitialized and triggers errors within libbpf APIs
which require strict zero initialization of OPTS structs.
Adding anonymous padding field fixes the issue.
Fixes: 9f81654eeb ("libbpf: Expose BTF-to-C type declaration emitting API")
Suggested-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: KP Singh <kpsingh@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210319192117.2310658-1-kpsingh@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cab62c37be057379a2a17b1b2eacd9dcba1e14dc ]
Trigger vmlinux.h and BPF skeletons re-generation if detected that bpftool was
re-compiled. Otherwise full `make clean` is required to get updated skeletons,
if bpftool is modified.
Fixes: acbd06206b ("selftests/bpf: Add vmlinux.h selftest exercising tracing of syscalls")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210318194036.3521577-11-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dde7b3f5f2f458297aeccfd4783e53ab8ca046db ]
Adding such anonymous padding fixes the issue with uninitialized portions of
bpf_xdp_set_link_opts when using LIBBPF_DECLARE_OPTS macro with inline field
initialization:
DECLARE_LIBBPF_OPTS(bpf_xdp_set_link_opts, opts, .old_fd = -1);
When such code is compiled in debug mode, compiler is generating code that
leaves padding bytes uninitialized, which triggers error inside libbpf APIs
that do strict zero initialization checks for OPTS structs.
Adding anonymous padding field fixes the issue.
Fixes: bd5ca3ef93 ("libbpf: Add function to set link XDP fd while specifying old program")
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20210313210920.1959628-2-andrii@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 210e4c89ef61432040c6cd828fefa441f4887186 ]
The 'ret' variable was initialized to zero but then it was not updated
from the fprintf() return, fix it.
Reported-by: Yang Li <yang.lee@linux.alibaba.com>
cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
cc: Ingo Molnar <mingo@redhat.com>
cc: Jiri Olsa <jolsa@redhat.com>
cc: Mark Rutland <mark.rutland@arm.com>
cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Fixes: 90f18e63fb ("perf symbols: List symbols in a dso in ascending name order")
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb4969e6f9f5ee12521aec764fa3d4bbd91bc797 ]
Currently the following command produces an error message:
linux# make kselftest TARGETS=bpf O=/mnt/linux-build
# selftests: bpf: test_libbpf.sh
# ./test_libbpf.sh: line 23: ./test_libbpf_open: No such file or directory
# test_libbpf: failed at file test_l4lb.o
# selftests: test_libbpf [FAILED]
The error message might not affect the return code of make, therefore
one needs to grep make output in order to detect it.
This is not the only instance of the same underlying problem; any test
with more than one element in $(TEST_PROGS) fails the same way. Another
example:
linux# make O=/mnt/linux-build TARGETS=splice kselftest
[...]
# ./short_splice_read.sh: 15: ./splice_read: not found
# FAIL: /sys/module/test_module/sections/.init.text 2
not ok 2 selftests: splice: short_splice_read.sh # exit=1
The current logic prepends $(OUTPUT) only to the first member of
$(TEST_PROGS). After that, run_one() does
cd `dirname $TEST`
For all tests except the first one, `dirname $TEST` is ., which means
they cannot access the files generated in $(OUTPUT).
Fix by using $(addprefix) to prepend $(OUTPUT)/ to each member of
$(TEST_PROGS).
Fixes: 1a940687e4 ("selftests: lib.mk: copy test scripts and test files for make O=dir run")
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b2b94be787bf47eedd5890a249f3318bf9f1f1d5 upstream.
This reverts commit 6ff7cb371c.
Apparently the TCC offset should not be used to adjust what temperature
we show the user after all.
(on most systems, TCC offset is 0, FWIW)
Fixes: 6ff7cb371c
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13a779de4175df602366d129e41782ad7168cef0 upstream.
The idx_to_offset() function returns type int (32-bit signed), but
MSR_PKG_ENERGY_STAT is u32 and would be interpreted as a negative number.
The end result is that it hits the if (offset < 0) check in update_msr_sum()
which prevents the timer callback from updating the stat in the background when
long durations are used. The similar issue exists in offset_to_idx() and
update_msr_sum(). Fix this issue by converting the 'int' to 'off_t' accordingly.
Fixes: 9972d5d84d ("tools/power turbostat: Enable accumulate RAPL display")
Signed-off-by: Calvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 301b1d3a9104f4f3a8ab4171cf88d0f55d632b41 upstream.
It was reported that on Zen+ system turbostat started exiting,
which was tracked down to the MSR_PKG_ENERGY_STAT read failing because
offset_to_idx wasn't returning a non-negative index.
This patch combined the modification from Bingsong Si and
Bas Nieuwenhuizen and addd the MSR to the index system as alternative for
MSR_PKG_ENERGY_STATUS.
Fixes: 9972d5d84d ("tools/power turbostat: Enable accumulate RAPL display")
Reported-by: youling257 <youling257@gmail.com>
Tested-by: youling257 <youling257@gmail.com>
Tested-by: Kurt Garloff <kurt@garloff.de>
Tested-by: Bingsong Si <owen.si@ucloud.cn>
Tested-by: Artem S. Tashkinov <aros@gmx.com>
Co-developed-by: Bingsong Si <owen.si@ucloud.cn>
Co-developed-by: Terry Bowman <terry.bowman@amd.com>
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Reviewed-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: Salvatore Bonaccorso <carnil@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
