I got the following message:
> Your mail to 'Intel-wired-lan' with the subject
>
> [PATCH net-next] net: intel: remove dead links
>
> Is being held until the list moderator can review it for approval.
>
> The reason it is being held:
>
> Post by non-member to a members-only list
Mark the list as moderated.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc says:
====================
vxlan: implement Generic Protocol Extension (GPE)
v3: just rebased on top of the current net-next, no changes
This patchset implements VXLAN-GPE. It follows the same model as the tun/tap
driver: depending on the chosen mode, the vxlan interface is created either
as ARPHRD_ETHER (non-GPE) or ARPHRD_NONE (GPE).
Note that the internal fdb control plane cannot be used together with
VXLAN-GPE and attempt to configure it will be rejected by the driver. In
fact, COLLECT_METADATA is required to be set for now. This can be relaxed in
the future by adding support for static PtP configuration; it will be
backward compatible and won't affect existing users.
The previous version of the patchset supported two GPE modes, L2 and L3. The
L2 mode (now called "ether mode" in the code) was removed from this version.
It can be easily added later if there's demand. The L3 mode is now called
"raw mode" and supports also encapsulated Ethernet headers (via ETH_P_TEB).
The only limitation of not having "ether mode" for GPE is for ip route based
encapsulation: with such setup, only IP packets can be encapsulated. Meaning
no Ethernet encapsulation. It seems there's not much use for this, though.
If it turns out to be useful, we'll add it.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement VXLAN-GPE. Only COLLECT_METADATA is supported for now (it is
possible to support static configuration, too, if there is demand for it).
The GPE header parsing has to be moved before iptunnel_pull_header, as we
need to know the protocol.
v2: Removed what was called "L2 mode" in v1 of the patchset. Only "L3 mode"
(now called "raw mode") is added by this patch. This mode does not allow
Ethernet header to be encapsulated in VXLAN-GPE when using ip route to
specify the encapsulation, IP header is encapsulated instead. The patch
does support Ethernet to be encapsulated, though, using ETH_P_TEB in
skb->protocol. This will be utilized by other COLLECT_METADATA users
(openvswitch in particular).
If there is ever demand for Ethernet encapsulation with VXLAN-GPE using
ip route, it's easy to add a new flag switching the interface to
"Ethernet mode" (called "L2 mode" in v1 of this patchset). For now,
leave this out, it seems we don't need it.
Disallowed more flag combinations, especially RCO with GPE.
Added comment explaining that GBP and GPE cannot be set together.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow calling of iptunnel_pull_header without special casing ETH_P_TEB inner
protocol.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle VXLAN_F_COLLECT_METADATA before VXLAN_F_PROXY. The latter does not
make sense with the former, as it needs populated fdb which does not happen
in metadata mode.
After this cleanup, the fdb code in vxlan_xmit is moved to a common location
and can be later skipped for VXLAN-GPE which does not necessarily carry
inner Ethernet header.
v2: changed commit description to not reference L3 mode
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow to initialize vxlan in ARPHRD_NONE mode based on the passed
rtnl attributes.
v2: renamed "l2mode" to "ether".
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of these tests proved useful with the powerpc eBPF JIT port due to
sign-extended 16-bit immediate loads. Though some of these aspects get
covered in other tests, it is better to have explicit tests so as to
quickly tag the precise problem.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF_ALU32 and BPF_ALU64 tests for adding two 32-bit values that results in
32-bit overflow.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unsigned Jump-if-Greater-Than.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
JMP_JSET tests incorrectly used BPF_JNE. Fix the same.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's see if anybody even notices. I doubt anybody uses this, and it
does expose addresses that should be randomized, so let's just remove
the code. It's old and traditional, and it used to be cute, but we
should have removed this long ago.
If it turns out anybody notices and this breaks something, we'll have to
revert this, and maybe we'll end up using other approaches instead
(using %pK or similar). But removing unnecessary code is always the
preferred option.
Noted-by: Emrah Demir <ed@abdsec.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The check in vmci_transport_peer_detach_cb should only allow a
detach when the qp handle of the transport matches the one in
the detach message.
Testing: Before this change, a detach from a peer on a different
socket would cause an active stream socket to register a detach.
Reviewed-by: George Zhang <georgezhang@vmware.com>
Signed-off-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While initializing the phy, the stmmac driver sets the
PHY_IGNORE_INTERRUPT so the PAL won't call the adjust hook
that is needed, on some platforms, e.g. STi, to invoke the glue.
The patch allows the PAL to poll the stmmac_adjust_link just one time
in case of a switch is attached, setting later the PHY_IGNORE_INTERRUPT
flag.
Moving this kind of logic inside the adjust_link it makes sense to
anticipate the check for EEE that will never initialized in this
scenario.
Reported-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Garbled output for "ethtool -m ethX", in igb-driven NICs with module /
plugin EEPROM (i.e. SFP information). Each output data byte appears
duplicated.
In igb_ethtool.c, igb_get_module_eeprom() is reading the EEPROM via i2c;
the eeprom offset for each word that's read via igb_read_phy_reg_i2c()
was passed in #words, whereas it needs to be a byte offset.
This patches fixes the bug.
Signed-off-by: Doron Shikmoni <doron.shikmoni@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Message level can be set through ethtool, so deprecate module parameter
which is used to set the same.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trinity and other fuzzers can hit this WARN on far too easily,
resulting in a tainted kernel that hinders automated fuzzing.
Replace it with a rate-limited printk.
Signed-off-by: Dave Jones <davej@codemonkey.org.uk>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: ddf97ccdd7 ("net_sched: add network namespace support for tc actions")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Tested-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the necessary definitions for building bpf samples on ppc.
Since ppc doesn't store function return address on the stack, modify how
PT_REGS_RET() and PT_REGS_FP() work.
Also, introduce PT_REGS_IP() to access the instruction pointer.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While at it, remove the generation of .s files and fix some typos in the
related comment.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building BPF samples is failing with the below error:
samples/bpf/map_perf_test_user.c: In function ‘main’:
samples/bpf/map_perf_test_user.c:134:9: error: variable ‘r’ has
initializer but incomplete type
struct rlimit r = {RLIM_INFINITY, RLIM_INFINITY};
^
samples/bpf/map_perf_test_user.c:134:21: error: ‘RLIM_INFINITY’
undeclared (first use in this function)
struct rlimit r = {RLIM_INFINITY, RLIM_INFINITY};
^
samples/bpf/map_perf_test_user.c:134:21: note: each undeclared
identifier is reported only once for each function it appears in
samples/bpf/map_perf_test_user.c:134:9: warning: excess elements in
struct initializer [enabled by default]
struct rlimit r = {RLIM_INFINITY, RLIM_INFINITY};
^
samples/bpf/map_perf_test_user.c:134:9: warning: (near initialization
for ‘r’) [enabled by default]
samples/bpf/map_perf_test_user.c:134:9: warning: excess elements in
struct initializer [enabled by default]
samples/bpf/map_perf_test_user.c:134:9: warning: (near initialization
for ‘r’) [enabled by default]
samples/bpf/map_perf_test_user.c:134:16: error: storage size of ‘r’
isn’t known
struct rlimit r = {RLIM_INFINITY, RLIM_INFINITY};
^
samples/bpf/map_perf_test_user.c:139:2: warning: implicit declaration of
function ‘setrlimit’ [-Wimplicit-function-declaration]
setrlimit(RLIMIT_MEMLOCK, &r);
^
samples/bpf/map_perf_test_user.c:139:12: error: ‘RLIMIT_MEMLOCK’
undeclared (first use in this function)
setrlimit(RLIMIT_MEMLOCK, &r);
^
samples/bpf/map_perf_test_user.c:134:16: warning: unused variable ‘r’
[-Wunused-variable]
struct rlimit r = {RLIM_INFINITY, RLIM_INFINITY};
^
make[2]: *** [samples/bpf/map_perf_test_user.o] Error 1
Fix this by including the necessary header file.
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel i211 LOM PCIe Ethernet controllers' iNVM operates as an OTP
and has no external EEPROM interface [1]. The following allows the
driver to pickup the MAC address from a device tree blob when CONFIG_OF
has been enabled.
[1]
http://www.intel.com/content/www/us/en/embedded/products/networking/i211-ethernet-controller-datasheet.html
Signed-off-by: John Holland <jotihojr@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables bulk free in Tx cleanup for igb and cleans up the
boolean logic in the polling routines for igb in the hopes of avoiding
any mix-ups similar to what occurred with i40e and i40evf.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were casting the addr as __beXX and then passing it into le32_to_cpu
because the device expects the MAC address to be in network order even
though the register set is little endian. Instead of casting it as __beXX
we can just cast it as __leXX in order to maintain consistency since the
region of memory is already in little endian order as far as we are
concerned.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Low priority scan handling code which delays or aborts scan
operation based on Tx traffic is removed recently. The reason
is firmware already takes care of it in our new feature scan
channel gap. Hence we should advertise low priority scan
support to cfg80211.
This patch fixes a problem in which OBSS scan request from
wpa_supplicant was being rejected by cfg80211.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Tested-by: Wei-Ning Huang <wnhuang@chromium.org>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
retry_limit has never been used during the life of this driver, so
we may as well remove it as it is redundant.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With current driver, it is observed that a URB is not
completed while the USB disconnect is initiated. Due to
that, the URB completion handler is trying to access
the resource which was freed as a part of USB disconnect.
Managing the URBs with anchor will make sure that all
the URBs are handled gracefully before device gets
disconnected.
Signed-off-by: Vishal Thanki <vishalthanki@gmail.com>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ssid is an array of u8, so it can never be null, so the null check on
wl->scan.ssid is redundant and can be removed.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use a more common logging style.
Miscellanea:
o Add specific logging macros for ALGORITHM and INTERFACE types
o Output the messages at KERN_DEBUG
o Coalesce formats
o Align arguments
o Whitespace style adjustments for only these changes
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch reports the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c:137 rtl8723e_dm_bt_need_to_dec_bt_pwr() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch lists the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8192se/phy.c
drivers/net/wireless/realtek/rtlwifi/rtl8192se/phy.c:648 rtl92s_phy_set_rf_power_state() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch lists the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c
drivers/net/wireless/realtek/rtlwifi/rtl8192ee/trx.c:371 rtl92ee_rx_query_desc() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch lists the following:
CHECK drivers/net/wireless/realtek/rtlwifi/rtl8192c/dm_common.c
drivers/net/wireless/realtek/rtlwifi/rtl8192c/dm_common.c:243 rtl92c_dm_false_alarm_counter_statistics() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch reports the following:
CHECK drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c
drivers/net/wireless/realtek/rtlwifi/btcoexist/halbtc8723b2ant.c:3078 btc8723b2ant_run_coexist_mechanism() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch reports the following:
CHECK drivers/net/wireless/realtek/rtlwifi/pci.c
drivers/net/wireless/realtek/rtlwifi/pci.c:366 rtl_pci_check_buddy_priv() error: we previously assumed 'tpriv' could be null (see line 368)
drivers/net/wireless/realtek/rtlwifi/pci.c:1216 _rtl_pci_init_struct() warn: inconsistent indenting
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
- Fix mlx5 build error when on demand paging is not enabled
- Fix possible uninit variable in new i40iw driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PcOX
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"I'm back from PTO. These issues cropped up while I was gone and are
simple fixes. I'll have more after I've caught up, but I wanted to
get these in quick.
Two minor fixes for 4.6-rc2:
- Fix mlx5 build error when on demand paging is not enabled
- Fix possible uninit variable in new i40iw driver"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
i40iw: avoid potential uninitialized variable use
IB/mlx5: fix VFs callback function prototypes
The previous patch added an option to rtl8723be to manually select the
antenna for those cases when only a single antenna is present, and the
on-board EEPROM is incorrectly programmed. This patch implements the
necessary changes in the Bluetooth coexistence driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V4.0+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
A number of new laptops have been delivered with only a single antenna.
In principle, this is OK; however, a problem arises when the on-board
EEPROM is programmed to use the other antenna connection. The option
of opening the computer and moving the connector is not always possible
as it will void the warranty in some cases. In addition, this solution
breaks the Windows driver when the box dual boots Linux and Windows.
A fix involving a new module parameter has been developed. This commit
adds the new parameter and implements the changes needed for the driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V4.0+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is an error path where "ret" isn't initialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Improvements in thermal (Chaya Rachel)
* Various cleanups (many people)
* Improvements in firmware error dump (Golan)
* More work 9000 devices and MSIx (Haim)
* Continuation of the Dynamic Queue Allocation work (Liad)
* Scan timeout to cope with buggy firmware (Luca)
* D0i3 improvements (Luca)
* Make the paging less memory hungry (Matti)
* 9000 new Rx path (Sara)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=USQo
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-03-30' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Support for Link Quality measurement (Aviya)
* Improvements in thermal (Chaya Rachel)
* Various cleanups (many people)
* Improvements in firmware error dump (Golan)
* More work 9000 devices and MSIx (Haim)
* Continuation of the Dynamic Queue Allocation work (Liad)
* Scan timeout to cope with buggy firmware (Luca)
* D0i3 improvements (Luca)
* Make the paging less memory hungry (Matti)
* 9000 new Rx path (Sara)
gcc finds that the i40iw_make_cm_node() function in the recently added
i40iw driver uses an uninitilized variable as an index into an array
if CONFIG_IPV6 is disabled and the driver uses IPv6 mode:
drivers/infiniband/hw/i40iw/i40iw_cm.c: In function 'i40iw_make_cm_node':
drivers/infiniband/hw/i40iw/i40iw_cm.c:2206:52: error: 'arpindex' may be used uninitialized in this function [-Werror=maybe-uninitialized]
ether_addr_copy(cm_node->rem_mac, iwdev->arp_table[arpindex].mac_addr);
As far as I can tell, this code path can not be used because the ipv4
variable is always set with CONFIG_IPV6 is disabled, but it's better
to be sure and prevent the undefined behavior, as well as shut up
that warning in a proper way.
This adds an 'else' clause for the case we get the warning about,
causing the function to return an error in a controlled way.
To avoid adding extra mess with combined io()/#ifdef clauses,
I'm also converting the existing #ifdef into a more readable
if(IS_ENABLED()) check.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f27b4746f3 ("i40iw: add connection management code")
Acked-by: Mustafa Ismail <Mustafa.ismail@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The previous patch that added a couple of callback functions put
the declarations inside of an #ifdef CONFIG_INFINIBAND_ON_DEMAND_PAGING,
which causes the build to fail if that option is disabled:
drivers/infiniband/hw/mlx5/main.c: In function 'mlx5_ib_add':
drivers/infiniband/hw/mlx5/main.c:2358:31: error: 'mlx5_ib_get_vf_config' undeclared (first use in this function)
This moves the four declarations below the #ifdef section so they
are always available.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: eff901d30e ("IB/mlx5: Implement callbacks for manipulating VFs")
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The Keystone 2 supports DT-boot only, as result dma_mask will be
always configured properly from DT -
of_platform_device_create_pdata()->of_dma_configure(). More over,
dwc3-keystone.c can be built as module and in this case it's unsafe to
assign local variable as dma_mask.
Hence, remove dma_mask configuration code.
Cc: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since commit 7ace8fc821 ("usb: gadget: udc: core: Fix argument of
dma_map_single for IOMMU") it is not necessary to configure DMA for
usb_gadget device manually, because all DMA operation are performed
using parent/controller device.
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
