So far only Luxul XWR-1750 router was supported. This adds a set of
other Luxul devices based on BCM47XX. It's a standard support for LEDs
and buttons.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15106/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Catalin reported that GPIOs used by bcm47xx don't match layout of his
WRT54GS V1.0 board. It seems we need to distinguish these 54G* devices.
Reported-by: Catalin Patulea <cat@vv.carleton.ca>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/7112/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a few Belkin F7Dxxxx entries, with F7D4401 sourced from online
documentation and the "F7D7302" being observed. F7D3301, F7D3302, and
F7D4302 are reasonable guesses which are unlikely to cause
mis-detection.
Signed-off-by: Cody P Schafer <devel@codyps.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Cc: Cody P Schafer <devel@codyps.com>
Patchwork: https://patchwork.linux-mips.org/patch/6594/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds board detection for the Siemens SE505v2 and the led gpio
configuration. This board does not have any buttons.
This is based on OpenWrt broadcom-diag and Manuel Munz's nvram dump.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6593/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Linksys WRT54G/GS/GL family uses the same boardtype numbers, and
the same gpio configuration. The boardtype numbers are changing with
the hardware versions, but these hardware numbers are different or each
model.
Detect them all as one device, this also worked in OpenWrt.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Cc: zajec5@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6591/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect on which board this code is running based on some nvram
settings. This is needed to start board specific workarounds and
configure the leds and buttons which are on different gpios on every board.
This patches add some boards we have seen, but there are many more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5840
Patchwork: https://patchwork.linux-mips.org/patch/5855/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
