This patch, adds to the option driver the Onda Communication
(http://www.ondacommunication.com) vendor id, and the MT825UP modem
device id.
Note that many variants of this same device are being release here in
Italy (at least one or two per telephony operator).
These devices are perfectly equivalent except for some predefined
settings (which can be changed of course).
It should be noted that most ONDA devices are allready supported (they
used other vendor's ids in the past). The patch seems working fine here,
and the rest of the driver seems uninfluenced.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for Accesio USB to Serial adapters, which are built around
FTDI FT232 UARTs. Tested with the Accesio USB-COM-4SM.
Signed-off-by: Rich Mattes <richmattes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are lots of ZTE USB id's currently not covered by usb/serial. Adds them,
to allow those devices to work properly on Linux.
While here, put the USB ID's for 0x2002/0x2003 at the sorted order.
This patch is based on zte.c file found on MF645.
PS.: The ZTE driver is commenting the USB ID for 0x0053. It also adds, commented,
an USB ID for 0x0026.
Not sure why, but I think that 0053 is used by their devices in storage mode only.
So, I opted to keep the comment on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new driver to access the SAM-BA boot application of Atmel AT91SAM
devices.
The SAM-BA firmware cannot handle merged write requests so we cannot use
the generic write implementation (which uses the port write fifo).
Tested with the SAM-BA 2.10 tools and an Atmel at91sam9260-ek.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The TIOCGICOUNT device ioctl in both mos7720.c and mos7840.c allows
unprivileged users to read uninitialized stack memory, because the
"reserved" member of the serial_icounter_struct struct declared on the
stack is not altered or zeroed before being copied back to the user.
This patch takes care of it.
Signed-off-by: Dan Rosenberg <dan.j.rosenberg@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added the 0xDAF8 to 0xDAFF PID range for ChamSys limited USB interface/wing products
Signed-off-by: Luke Lowrey <luke@chamsys.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB IDs needed to support the B&B USOPTL4-4P, USO9ML2-2P, and
USO9ML2-4P. This patch expands and corrects a typo in the patch sent
on 08-31-2010.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the USB ID needed to support B&B Electronic's 2-port, optically-isolated,
powered, USB to RS485 converter.
Signed-off-by: Dave Ludlow <dave.ludlow@bay.ws>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Pirelli DP-L10 mobile is sold under various brand names. One, already
supported by cp210x, is the T-COM TC300. Here is the lsusb for that version:
-------------------------------------------------------------------
Bus 001 Device 002: ID 0489:e000 Foxconn / Hon Hai T-Com TC 300
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe000 T-Com TC 300
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 TC 300
iSerial 3 0001
[snip]
---------------------------------------------------------------------------
However the native Pirelli DP-L10 is not supported:
------------------------------------------------------------------
Bus 001 Device 003: ID 0489:e003 Foxconn / Hon Hai Pirelli DP-L10
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x0489 Foxconn / Hon Hai
idProduct 0xe003 Pirelli DP-L10
bcdDevice 1.00
iManufacturer 1 Silicon Labs
iProduct 2 DP-L10
iSerial 3 0001
[snip]
-------------------------------------------------------------------------
All that is required is an extra USB_DEVICE entry:
{ USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM
+Mobile */
The patch adds that entry. Tested under 2.6.36-rc2 from git.
Signed-off-by: A E Lawrence <lawrence_a_e@ntlworld.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New device ID added for Balluff RFID reader.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unfortunately some of the hardware PID belonging to auto-install CDROM
(AICD) of Novatel modems found their way into the option module. This
causes the AICD to be treated as a modem in stead of a disk. Since the
modem ports do not appear until after the AICD is ejected, this
essentially disables the modem. After a couple of minutes the AICD
should auto-eject, but it is just too long a wait. The frequency of the
failure seems to depend on both the hardware and the linux distribution.
Here is a patch that fixes this up, and also adds a couple of new PID,
offering some explanations and removing some incomplete and unnecessary
comments.
Signed-off-by: Dirk De Schepper <ddeschepper@nvtl.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add ftdi product ID for Lenz LI-USB, a model train interface. This
was NOT tested against 2.6.35, but a similar patch was tested with the
CentOS 2.6.18-194.11.1.el5 kernel. It wasn't clear to me what
ordering is being used in ftdi_sio.c, so I inserted the ID after another
model train entry(SPROG_II).
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the ID for the Ionics PlugComputer (<http://ionicsplug.com/>).
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
flag was never set in ssu100_process_packet. Add logic to set it
before calling tty_insert_flip_*
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a disconnect function to the functions of this device. The
disconnect is a call to usb_serial_generic_disconnect() so it requires
that symbol to be exported from generic.c.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed by the ssu100 driver to use this function.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the logic for TIOCMIWAIT to use wait_event_interruptible.
This also adds support for TIOCGICOUNT.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function ssu100_setregister was hard coded to only set the MCR
register. Add a register parameter so that other registers can be
set.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ssu100 uses a TI16C550C UART so the SERIAL_ defines in this code
are duplicates of those found in serial_reg.h. Remove the defines in
ssu100.c and use the ones in the header file.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The status information does not appear at the start of each incoming
packet so the check for len < 4 at the start of ssu100_process_packet
is wrong. Remove it.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we can't read the firmware for a device from the disk, and yet the
device already has a valid firmware image in it, we don't want to
replace the firmware with something invalid. So check the version
number to be less than the current one to verify this is the correct
thing to do.
Reported-by: Chris Beauchamp <chris@chillibean.tv>
Tested-by: Chris Beauchamp <chris@chillibean.tv>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB max packet size (always little-endian) was not being byte
swapped on big-endian systems.
Applicable since [USB: ftdi_sio: fix hi-speed device packet size calculation] approx 2.6.31
Signed-off-by: Michael Wileczka <mikewileczka@yahoo.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The definitions for BREAK_ON and BREAK_OFF are inverted, causing break
requests to fail. This patch sets BREAK_ON and BREAK_OFF to the correct
values.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Zeagle N2iTiON3 dive computer interface. Since
Zeagle devices are actually manufactured by Seiko, this patch will
support other Seiko based models as well.
Signed-off-by: Jef Driesen <jefdriesen@telenet.be>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch with title below makes reference count of usb serial module
always more than one after driver is bound.
USB-BKL: Remove BKL use for usb serial driver probing
In fact, the patch above only replaces lock_kernel() with try_module_get()
, and does not use module_put() to do what unlock_kernel() did, so casue leak
of reference count of usb serial module and the module can not be unloaded
after serial driver is bound with device.
This patch fixes the issue, also simplifies such things:
-only call try_module_get() once in the entry of usb_serial_probe()
-only call module_put() once in the exit of usb_serial_probe
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I recently bought a i-gotU USB GPS, and whilst hunting around for linux
support discovered this post by you back in 2009:
http://kerneltrap.org/mailarchive/linux-usb/2009/3/12/5148644
>Try the navman driver instead. You can either add the device id to the
> driver and rebuild it, or do this before you plug the device in:
> modprobe navman
> echo -n "0x0df7 0x0900" > /sys/bus/usb-serial/drivers/navman/new_id
>
> and then plug your device in and see if that works.
I can confirm that the navman driver works with the right device IDs on
my i-gotU GT-600, which has the same device IDs. Attached is a patch
adding the IDs.
From: Ross Burton <ross@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since handle_sysrq() does not take tty as argument anymore we can
drop it from usb_serial_handle_sysrq_char() as well.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sysrq operations do not accept tty argument anymore so no need to pass
it to us.
[Stephen Rothwell <sfr@canb.auug.org.au>: fix build breakage in drm code
caused by sysrq using bool but not including linux/types.h]
[Sachin Sant <sachinp@in.ibm.com>: fix build breakage in s390 keyboadr
driver]
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As David VomLehn points out, it was possible to receive an interrupt
before clearing the free-urb flag which could lead to the urb being
incorrectly marked as busy.
For the same reason, move tx_bytes accounting so that it will never be
negative.
Note that the free-flags set and clear operations do not need any
additional locking as they are manipulated while USB_SERIAL_WRITE_BUSY
is set.
Reported-by: David VomLehn <dvomlehn@cisco.com>
Tested-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Quatech SSU-100 single port usb to serial device.
This driver is based on the ftdi_sio.c driver and the original
serqt_usb driver from Quatech.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is to add a US Interface, Inc. "Navigator" USB device.
Specifically, it's a HAM Radio USB sound modem that also
incorporates three pairs of unique FTDI serial ports. The standard
Linux FTDI serial driver will only recognize the first two serial
ports of an unknown FDTI derived device and this patch adds in
recognition to these specific new IDs.
Signed-off-by: David A. Ranch <dranch@trinnet.net>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the product IDs of Huawei's K3765 and K4505 mobile
broadband usb modems to option.c. It also adds a quirk to the option
probe function so that binding to the device's network interface(class
0xff) is avoided. This is necessary to allow another driver to bind to
that, and to avoid programs like wvdial opening a nonfunctioning tty
during modem discovery.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have added the ProductID=0xe729 VendorID=FTDI_VID=0x0403 which will
enable support for the Segway Robotic Mobility Platform (RMP200) in the
ftdi_sio kernel module. Currently, users of the Segway RMP200 must use
a RUN+="/sbin/modprobe -q ftdi-sio product=0xe729 vendor=0x0403 in a
udev rule to get the ftdi_sio module to handle the usb interface and
mount it on /dev/ttyXXX. This is not a good solution because some users
will have multiple USB to Serial converters which will use the ftdi_sio
module.
Signed-off-by: John Rogers <jgrogers@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch adds Huawei ETS 1220 product id into the list of supported
devices in 'option' usb serial driver.
Signed-off-by: Pavel Kazlou <p.i.kazlou@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Usb serial port device is child of its usb interface device, so
we can enable async suspend of usb serial port device to speedup
system suspend.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The usb serial driver initialization tried to use the BKL to stop
driver modules from unloading, but that didn't work anyways.
There was already some code to do proper try_module_get,
but it was conditional on having a new probe interface.
I checked all the low level drivers and they all have proper
.owner = THIS_MODULE, so it's ok to always use.
The other problem was the usb_serial_driver_list needing
protection by a lock. This was broken anyways because unregister
did not necessarily have the BKL.
I extended the extending table_lock mutex to protect this case too.
With these changes the BKL can be removed here.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ipaq already had this device id defined:
{ USB_DEVICE(0x0BB4, 0x00CF) }, /* HTC USB Modem */
Revert the commit which adds the duplicate entry.
This reverts commit 04cab13293.
Originally-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AMOI_VENDOR_ID is defined twice. Remove the duplicate entry and move
the AMOI_PRODUCT_9508 definition to be grouped with the other AMOI
product definitions.
Originally-by: Ben Collins <ben.collins@ubuntu.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
