The struct clk_lookup are marked as __initdata, resulting in being
removed from memory after the kernel finished booting. However this
leads to a NULL pointer de-ref if loading a module which uses clk_get.
This patch removes the __initdata from the struct clk_lookup.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The definition of clocks ref_io0 and ref_io1 were inverted. It causes
a mmc regression on some boards right away. Fix the regression by
correcting the ref_io clock definition.
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
clk_change_rate() is accessing parent's rate without checking
if the parent exists at all. In case of root clocks this will
cause NULL pointer dereference.
This patch follows what clk_calc_new_rates() does in such
situation.
Signed-off-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org
Parent clocks for muxes are cached in clk->parents to
avoid frequent lookups, however the cache allocation happens
only during clock registeration and later clk_set_parent()
assumes a cache space available and allocated.
This is not entirely true for platforms which do early clock
registerations wherein the cache allocation using kzalloc
could fail during clock registeration.
Allow cache allocation to happen later as part of clk_set_parent()
to help such cases and avoid crashes assuming a cache being
available.
While here also replace existing kmalloc() with kzalloc()
in the file.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Cc: stable@kernel.org
Add a missing resource release in ring cleanup.
Not doing this leaves a range of QPs that are being reserved,
and no one can use them.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a crash at the error flow of NOP command which caused the driver to try and use
a completion vector which wasn't allocated.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set valid port parameters: MTU and flow control configuration when
configuring the port during HW device initialization,
prior to the net device open() being called.
Using invalid parameters (such as all zeros)
could lead to bad firmware behavior.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds support for the iPad to the ipheth driver.
(product id = 0x129a)
Signed-off-by: Davide Gerhard <rainbow@irh.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a missing return, causing access to freed memory.
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a piggyback'ed descriptor containing an
embedded frame, but no payload, the embedded frame was
lost.
Signed-off-by: Per Ellefsen <per.ellefsen@stericsson.com>
Signed-off-by: Sjur Brændeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull media fixes from Mauro Carvalho Chehab.
Trivial conflict due to new USB HID ID's being added next to each other
(Baanto vs Axentia).
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (44 commits)
[media] smia: Fix compile failures
[media] Fix VIDIOC_DQEVENT docbook entry
[media] s5p-fimc: Fix control creation function
[media] s5p-mfc: Fix checkpatch error in s5p_mfc_shm.h file
[media] s5p-mfc: Fix setting controls
[media] v4l/s5p-mfc: added image size align in VIDIOC_TRY_FMT
[media] v4l/s5p-mfc: corrected encoder v4l control definitions
[media] v4l: mem2mem_testdev: Fix race conditions in driver
[media] s5p-mfc: Bug fix of timestamp/timecode copy mechanism
[media] cxd2820r: Fix an incorrect modulation type bitmask
[media] em28xx: Show a warning if the board does not support remote controls
[media] em28xx: Add remote control support for Terratec's Cinergy HTC Stick HD
[media] USB: Staging: media: lirc: initialize spinlocks before usage
[media] Revert "[media] media: mx2_camera: Fix mbus format handling"
[media] bw-qcam: driver and pixfmt documentation fixes
[media] cx88: fix firmware load on big-endian systems
[media] cx18: support big-endian systems
[media] ivtv: fix support for big-endian systems
[media] tuner-core: return the frequency range of the correct tuner
[media] v4l2-dev.c: fix g_parm regression in determine_valid_ioctls()
...
When authentication/association timed out, the driver would
complain bitterly, printing the message
ACTIVATE a non DRIVER active station id ... addr ...
The cause turns out to be that when the AP station is added
but we don't associate, the IWL_STA_UCODE_INPROGRESS is set
but never cleared. This then causes iwl_restore_stations()
to attempt to resend it because it uses the flag internally
and uploads even if it didn't set it itself.
To fix this issue and not upload the station again when it
has already been removed by mac80211, clear the flag after
adding it in case we add it only for association.
Cc: stable@vger.kernel.org
Reviewed-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mainline build reports:
warning: (WL12XX) selects WLCORE which has unmet direct dependencies (NETDEVICES && WLAN && WL_TI && GENERIC_HARDIRQS && MAC80211 && INET)
The INET dependency was added in commit
3c6af5b54f:
wl1271_main.c:(.text+0x271052): undefined reference to `unregister_inetaddr_
notifier'
wl1271_main.c:(.text+0x2714d7): undefined reference to `register_inetaddr_no
tifier'
Driver is doing some filtering based on IP addresses...
but this driver no longer has that code and it builds fine even when
CONFIG_INET is not enabled, so drop that dependency and eliminate the
kconfig warning message.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Luciano Coelho <luciano.coelho@nokia.com>
Cc: John W. Linville <linville@tuxdriver.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 7a532fe713
ath9k_hw: fix interpretation of the rx KeyMiss flag
This commit used the rx key miss indication to detect packets that were
passed from the hardware without being decrypted, however it seems that
this bit is not only undefined in the static WEP case, but also for
dynamically allocated WEP keys. This caused a regression when using
WEP-LEAP.
This patch fixes the regression by keeping track of which key indexes
refer to CCMP keys and only using the key miss indication for those.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few small, driver specific bug fixes, nothing exciting here but all
needed if you happen to be using the affected hardware.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=vzG1
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A few small, driver specific bug fixes, nothing exciting here but all
needed if you happen to be using the affected hardware."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: palmas: fix regmap offsets for enable/disable
regulator: tps6524x: Fix get_voltage_sel for fixed voltage
regulator: tps65023: Fix mask for LDOs output voltage select control
This is needed to sync up with the previous USB changes that were merged in
Linus's branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It makes sense to label "Digital Thermal Sensor" as "DTS", but
unfortunately the string "dts" was already used for "Debug Store", and
/proc/cpuinfo is a user space ABI.
Therefore, rename this to "dtherm".
This conflict went into mainline via the hwmon tree without any x86
maintainer ack, and without any kind of hint in the subject.
a4659053 x86/hwmon: fix initialization of coretemp
Reported-by: Jean Delvare <khali@linux-fr.org>
Link: http://lkml.kernel.org/r/4FE34BCB.5050305@linux.intel.com
Cc: Jan Beulich <JBeulich@suse.com>
Cc: <stable@vger.kernel.org> v2.6.36..v3.4
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The generic HID driver is obviously not a special driver, so move it
outside of the special drivers menu. Explain the usage and make the
default follow the HID setting. This should simplify migration from
older kernels. While at it, remove the redundant HID_SUPPORT option
and modify the HID and USB_HID entries to better explain the bus
structure.
Reported-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
My old e-mail address won't be valid for much longer. Time to update it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
In patch "HID: magicmouse: Adjust major / minor axes to scale",
touch_major and touch_minor axes are scaled by a factor of
four when reported but the max touch_major/minor is not scaled
accordingly. This patch scales the max touch_major/minor to
be consistent with the reported value.
Signed-off-by: Yufeng Shen <miletus@chromium.org>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Stops the media entity pipeline which was started earlier
if fimc_pipeline_validate fails.
[s.nawrocki: reworked to not exceed 80 characters line length]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is an update to changed media_entity_pipeline_start()
signature in commit af88be3887,
"media: Add link_validate() op to check links to the sink pad"
It fixes the following warning:
drivers/media/video/s5p-fimc/fimc-lite.c: In function ‘fimc_lite_streamon’:
drivers/media/video/s5p-fimc/fimc-lite.c:765:29: warning: ignoring return value
of ‘media_entity_pipeline_start’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Commit 77e7c4e624
"v4l: Allow changing control handler lock" changed
the lock field of struct v4l2_ctrl_handler to a pointer
and this driver wasn't updated properly. This patch fixes
following warning:
drivers/media/video/s5p-fimc/fimc-core.c: In function ‘fimc_ctrls_activate’:
drivers/media/video/s5p-fimc/fimc-core.c:644: warning: passing argument 1 of ‘mutex_lock’ from incompatible pointer type
include/linux/mutex.h:152: note: expected ‘struct mutex *’ but argument is of type ‘struct mutex **’
drivers/media/video/s5p-fimc/fimc-core.c:663: warning: passing argument 1 of ‘mutex_unlock’ from incompatible pointer type
include/linux/mutex.h:169: note: expected ‘struct mutex *’ but argument is of type ‘struct mutex **’
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Shorten pixel format descriptions that exceed 32 characters
so they're not being truncated when queried from user space.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Only suspend the video pipeline devices if they were active before
the pm.suspend() helper is called. This patch prevents following error:
/# echo mem > /sys/power/state
[ 34.965000] PM: Syncing filesystems ... done.
[ 35.035000] Freezing user space processes ... (elapsed 0.01 seconds) done.
...
[ 35.105000] dpm_run_callback(): platform_pm_suspend+0x0/0x5c returns -22
[ 35.105000] PM: Device exynos-fimc-lite.1 failed to suspend: error -22
[ 35.105000] PM: Some devices failed to suspend
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera clocks managed by the driver were improperly reference counted
and remained disabled when multiple video nodes were opened simultaneously.
It manifested itself with following warning:
[12.920000] WARNING: at drivers/media/video/s5p-fimc/fimc-mdevice.c:787 __fimc_md_set_camclk+0x1c0/0x1dc()
[13.005000] Modules linked in:
[13.005000] Backtrace:
[13.040000] [<c0013084>] (dump_backtrace+0x0/0x10c) from [<c0454b70>] (dump_stack+0x18/0x1c)
[13.070000] r7:00000009 r6:00000313 r5:c02d576c r4:00000000
[13.155000] [<c0454b58>] (dump_stack+0x0/0x1c) from [<c0022ec4>] (warn_slowpath_common+0x54/0x6c)
[13.285000] [<c0022e70>] (warn_slowpath_common+0x0/0x6c) from [<c0022f00>] (warn_slowpath_null+0x24/0x2c)
[13.360000] r9:e1981010 r8:00000000 r7:c061d3fc r6:e1981010 r5:e1981030
[13.430000] r4:00000000
[13.430000] [<c0022edc>] (warn_slowpath_null+0x0/0x2c) from [<c02d576c>] (__fimc_md_set_camclk+0x1c0/0x1dc)
[13.550000] [<c02d55ac>] (__fimc_md_set_camclk+0x0/0x1dc) from [<c02d57b0>] (fimc_md_set_camclk+0x28/0x2c)
[13.630000] [<c02d5788>] (fimc_md_set_camclk+0x0/0x2c) from [<c02d57e8>] (__fimc_pipeline_shutdown+0x34/0x50)
[13.705000] [<c02d57b4>] (__fimc_pipeline_shutdown+0x0/0x50) from [<c02d5844>] (fimc_pipeline_shutdown+0x40/0x58)
[13.765000] r5:e2391200 r4:e2357704
[13.805000] [<c02d5804>] (fimc_pipeline_shutdown+0x0/0x58) from [<c02d4754>] (fimc_capture_close+0xcc/0xe4)
[13.915000] r5:e1b396c0 r4:e2357410
[13.915000] [<c02d4688>] (fimc_capture_close+0x0/0xe4) from [<c02b2d5c>] (v4l2_release+0x5c/0x80)
[13.970000] r7:00000010 r6:e1d2d990 r5:e1b396c0 r4:e2394800
[14.000000] [<c02b2d00>] (v4l2_release+0x0/0x80) from [<c00b66cc>] (fput+0xc0/0x22c)
[14.015000] r5:c157ef30 r4:e1b396c0
[14.015000] [<c00b660c>] (fput+0x0/0x22c) from [<c00b2ca0>] (filp_close+0x60/0x80)
[14.080000] [<c00b2c40>] (filp_close+0x0/0x80) from [<c00b2d78>] (sys_close+0xb8/0xf4)
[14.125000] r7:00000001 r6:e1b396c0 r5:c1400340 r4:c1400300
[14.125000] [<c00b2cc0>] (sys_close+0x0/0xf4) from [<c000f300>] (ret_fast_syscall+0x0/0x30)
[14.205000] r7:00000006 r6:beee5b94 r5:00000003 r4:b6f64fac
Fix this, as well as potential memory leaks due to not calling
v4l2_fh_release() on some error paths.
Also remove some error logs printed for events that aren't critical and
are normal conditions for some system configurations.
Also check if the device have been properly run-time enabled during
video node open.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The checks are already done at the v4l2 framework.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Allow memory buffer size to be increased by means of
struct v4l2_pix_plane_format::sizeimage at VIDIOC_S_FMT ioctl.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver is supposed to create active media link from sensor N
(or its corresponding s5p-mipi-csis entity) to FIMC.N by default.
Instead s5p-mipi-csis.N entity gets always connected by a default
active link to FIMC.N, regardless of there are parallel bus sensor
entities already connected to FIMC.N. Correct this.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When video pipeline initialization fails, the ST_CAPT_BUSY flag
needs to be cleared before pm_runtime_put_sync is called.
Otherwise the runtime suspend routine tries to suspend device,
rather than just turning it off. Also fix potential null pointer
dereference in fimc_pipeline_shutdown().
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When a device is added to the system at runtime the AMD
IOMMU driver initializes the necessary data structures to
handle translation for it. But it forgets to change the
per-device dma_ops to point to the AMD IOMMU driver. So
mapping actually never happens and all DMA accesses end in
an IO_PAGE_FAULT. Fix this.
Reported-by: Stefan Assmann <sassmann@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This is a port of
commit b49f184b64
Author: Ben Collins <bcollins@ubuntu.com>
from udlfb to udl kms driver.
The driver was not using le16_to_cpu when reading keys from the vendor
descriptor, causing incorrect parsing. Mainly, sku_pixel_limit was not
being parsed on big-endian systems. This would result in a blank screen
on big-endian CPUs where the DL chips's max mode was smaller than the
monitor's native mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
I've not had a gmail address for years. This commit updates the
address to my actual working one.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
__device_suspend() must always send a completion. Otherwise, parent
devices will wait forever.
Commit 1e2ef05b, "PM: Limit race conditions between runtime PM and
system sleep (v2)", introduced a regression by short-circuiting the
complete_all() for certain error cases.
This patch fixes the bug by always signalling a completion.
Addresses http://crosbug.com/31972
Tested by injecting an abort.
Signed-off-by: Mandeep Singh Baines <msb@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
- Fixes to new ocrdma driver
- Typo in test in CMA
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LFia
-----END PGP SIGNATURE-----
Merge tag 'rdma-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA fixes from Roland Dreier:
- Fixes to new ocrdma driver
- Typo in test in CMA
* tag 'rdma-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/cma: QP type check on received REQs should be AND not OR
RDMA/ocrdma: Fix off by one in ocrdma_query_gid()
RDMA/ocrdma: Fixed RQ error CQE polling
RDMA/ocrdma: Correct queue SGE calculation
RDMA/ocrdma: Correct reported max queue sizes
RDMA/ocrdma: Fixed GID table for vlan and events
Pull drm fixes from Dave Airlie:
"Nothing major in here, one radeon SI fix for tiling, and one uninit
var fix, two minor header file fixes."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm: drop comment about this header being autogenerated.
drm/edid: don't return stack garbage from supports_rb
vga_switcheroo: Add include guard
drm/radeon: SI tiling fixes for display
I forgot to apply the offsets for the regmap helper functions for
enable/disable on SMPS10 and the LDO regulators. This means regulators
will not enable/disable correctly.
Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Tested-by: Sebastien Guiriec <s-guiriec@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A few remaining fixes for our v3.5 cycle containing a fix
for a long standing bug which would cause musb to starve its
dma channels by never releasing them, a build fix on lpc32xx_udc,
another fix to Ido's endpoint descriptor series on fsl udc, a
fix to the order of arguments on twl6030-usb driver and a
fix to dwc3's dequeue method.
All patches have been pending on the list for quite a while.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=0Dme
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
usb: fixes for v3.5-rc3
A few remaining fixes for our v3.5 cycle containing a fix
for a long standing bug which would cause musb to starve its
dma channels by never releasing them, a build fix on lpc32xx_udc,
another fix to Ido's endpoint descriptor series on fsl udc, a
fix to the order of arguments on twl6030-usb driver and a
fix to dwc3's dequeue method.
All patches have been pending on the list for quite a while.
This patch (as1560) reverts commit
afff07e61a (usb-storage: Add 090c:1000
to unusal-devs). It is no longer needed, because usb-storage now
tells the sd driver to try READ CAPACITY(10) before READ CAPACITY(16)
for every USB mass-storage device.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly. They
report bogus sizes, in some cases becoming unusable as a result.
The bugs were triggered by commit
09b6b51b0b (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices. By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.
It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly. Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.
Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device. If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.
This fixes Bugzilla #43391.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following commit couldn't work if the RMCR is not set to 1.
"net: sh_eth: fix the rxdesc pointer when rx descriptor empty happens"
commit id 79fba9f517
If RMCR is not set, the controller will clear the EDRRR after it received
a frame. In this case, the driver doesn't need to fix the value of
cur_rx/dirty_rx. The driver only needs it when the controll detects
receive descriptors are empty.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8168evl (RTL_GIGA_MAC_VER_34) based Gigabyte GA-990FXA motherboards
are very prone to NETDEV watchdog problems without this change. See
https://bugzilla.kernel.org/show_bug.cgi?id=42899 for instance.
I don't know why it *works*. It's depressingly effective though.
For the record:
- the problem may go along IOMMU (AMD-Vi) errors but it really looks
like a red herring.
- the patch sets the RX_MULTI_EN bit. If the 8168c doc is any guide,
the chipset now fetches several Rx descriptors at a time.
- long ago the driver ignored the RX_MULTI_EN bit.
e542a2269f changed the RxConfig
settings. Whatever the problem it's now labeled a regression.
- Realtek's own driver can identify two different 8168evl devices
(CFG_METHOD_16 and CFG_METHOD_17) where the r8169 driver only
sees one. It sucks.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If usbnet is resumed by remote wakeup, generally there are
some packets comming to be handled, so allocate and submit
rx URBs in usbnet_resume to avoid delays introduced by tasklet.
Otherwise, usbnet may have been runtime suspended before the
usbnet_bh is executed to schedule Rx URBs.
Without the patch, usbnet can't recieve any packets from peer
in runtime suspend state if runtime PM is enabled and
autosuspend_delay is set as zero.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch decreases dev->suspend_count in the -EBUSY failure path
of usbnet_suspend. Without the change, the later runtime suspend
will do nothing except for increasing dev->suspend_count.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without clearing OPEN flag in failure path, runtime or system resume
may submit interrupt/rx URB and start tx queue mistakenly on a
interface in DOWN state.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ignoring interfaces with additional descriptors is not a reliable
method for locating the correct interface on Gobi devices. There
is at least one device where this method fails:
https://bbs.archlinux.org/viewtopic.php?id=143506
The result is that the AT command port (interface #2) is hidden
from qcserial, preventing traditional serial modem usage:
[ 15.562552] qmi_wwan 4-1.6:1.0: cdc-wdm0: USB WDM device
[ 15.562691] qmi_wwan 4-1.6:1.0: wwan0: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[ 15.563383] qmi_wwan: probe of 4-1.6:1.1 failed with error -22
[ 15.564189] qmi_wwan 4-1.6:1.2: cdc-wdm1: USB WDM device
[ 15.564302] qmi_wwan 4-1.6:1.2: wwan1: register 'qmi_wwan' at usb-0000:00:1d.0-1.6, Qualcomm Gobi wwan/QMI device, 1e:df:3c:3a:4e:3b
[ 15.564328] qmi_wwan: probe of 4-1.6:1.3 failed with error -22
[ 15.569376] qcserial 4-1.6:1.1: Qualcomm USB modem converter detected
[ 15.569440] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB0
[ 15.570372] qcserial 4-1.6:1.3: Qualcomm USB modem converter detected
[ 15.570430] usb 4-1.6: Qualcomm USB modem converter now attached to ttyUSB1
Use static interface numbers taken from the interface map in
qcserial for all Gobi devices instead:
Gobi 1K USB layout:
0: serial port (doesn't respond)
1: serial port (doesn't respond)
2: AT-capable modem port
3: QMI/net
Gobi 2K+ USB layout:
0: QMI/net
1: DM/DIAG (use libqcdm from ModemManager for communication)
2: AT-capable modem port
3: NMEA
This should be more reliable over all, and will also prevent the
noisy "probe failed" messages. The whitelisting logic is expected
to be replaced by direct interface number matching in 3.6.
Reported-by: Heinrich Siebmanns (Harvey) <H.Siebmanns@t-online.de>
Cc: <stable@vger.kernel.org> # v3.4: 0000188 USB: qmi_wwan: Make forced int 4 whitelist generic
Cc: <stable@vger.kernel.org> # v3.4: f7142e6 USB: qmi_wwan: Add ZTE (Vodafone) K3520-Z
Cc: <stable@vger.kernel.org> # v3.4
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the problem on some HP desktop machines with eDP
which give blank screens after S3 resume.
It turned out that BLC_PWM_CPU_CTL must be written after
BLC_PWM_CPU_CTL2. Otherwise it doesn't take effect on these
SNB machines.
Tested with 3.5-rc3 kernel.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=49233
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After banging my head against this for the past few months, I still
don't see how this could possible race under the premise that once an
irq bit is masked in PM_IMR and reset in PM_IIR it won't show up again
until we unmask it in PM_IMR.
Still, we have reports of this being seen in the wild. Now Bspec has
this little bit of lovely language in the PMIIR register:
Public SNB Docs, Vol3Part2, 2.5.14 "PMIIR":
"For each bit, the IIR can store a second pending interrupt if two or
more of the same interrupt conditions occur before the first condition
is cleared. Upon clearing the interrupt, the IIR bit will momentarily
go low, then return high to indicate there is another interrupt
pending."
Now if we presume that PMIMR only prevent new interrupts from being
queued, we could easily end up masking an interrupt and clearing it,
but the 2nd pending interrupt setting the bit in PMIIR right away
again. Which leads, the next time the irq handler runs, to hitting the
WARN.
Also, no bad side effects of this have ever been reported. And we've
tracked down our issues with the gpu turbo getting stuck to bogus
interrupt generation limits in th RPLIMIT register.
So let's just rip out this WARN as bogus and call it a day. The only
shallow thing here is that this 2-deep irq queue in the hw makes you
wonder how racy the windows irq handler is ...
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=42907
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
skb allocated during initialisation is reused for receiving
commands/events by USB interface. We miss to reset skb->data in
failure cases. This patch takes care of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ensures uniformity in event skb sent by interface code
(USB/PCIe/SDIO) which automatically fixes following bugs.
1) For USB interface, same buffer is reused for receiving cmd and
events from firmware. While handling events, we perform
skb_pull(skb, 4) to remove event header. Corresponding skb_push()
call is missing while submitting the buffer.
2) For PCIe interface, event skb is passed with event header.
Recently added uAP events EVENT_UAP_STA_ASSOC, EVENT_UAP_STA_DEAUTH
will not work for PCIe, as they assume event skb points to event body.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After association, STA will go through eapol handshake with WPS
enabled AP. It's observed that WPS handshake fails with some 11n
AP. The reason for the failure is that the eapol packet is sent
via 11n frame aggregation.
The eapol packet should be sent directly without 11n aggregation.
This patch fixes the problem by adding WPS session control while
dequeuing Tx packets for transmission.
Cc: "3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently we check the sequence number of last packet received
against start_win. If a sequence hole is detected, start_win is
updated to next sequence number.
Since the rx sequence number is initialized to 0, a corner case
exists when BA setup happens immediately after association. As
0 is a valid sequence number, start_win gets increased to 1
incorrectly. This causes the first packet with sequence number 0
being dropped.
Initialize rx sequence number as 0xffff and skip adjusting
start_win if the sequence number remains 0xffff. The sequence
number will be updated once the first packet is received.
Cc: "3.0.y, 3.1.y, 3.2.y, 3.3.y, 3.4.y" <stable@vger.kernel.org>
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently DMA channels are allocated and they remain allocated
even if there is no active data transfer. Added channel_release()
whenever there is no pending request.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If CONFIG_USB_GADGET_DEBUG_FILES is enabled, lpc32xx_udc breaks
compilation because of a missing include file.
Signed-off-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There were mistakes in writing to few twl
registers. There was interchange in the
parameters being passed to twl6030_writeb().
Signed-off-by: Moiz Sonasath <m-sonasath@ti.com>
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Two minor fixes in emc2103 and applesmc drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kDRE
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Two minor fixes in emc2103 and applesmc drivers."
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (emc2103) Fix use of an uninitilized variable in error case
hwmon: (applesmc) Limit key length in warning messages
The OProfile perf backend uses a static array to keep track of the
perf events on the system. When compiling with CONFIG_CPUMASK_OFFSTACK=y
&& SMP, nr_cpumask_bits is not a compile-time constant and the build
will fail with:
oprofile_perf.c:28: error: variably modified 'perf_events' at file scope
This patch uses NR_CPUs instead of nr_cpumask_bits for the array
initialisation. If this causes space problems in the future, we can
always move to dynamic allocation for the events array.
Cc: Matt Fleming <matt@console-pimps.org>
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cc: <stable@vger.kernel.org> # v2.6.37+
Signed-off-by: Robert Richter <robert.richter@amd.com>
drivers/media/video/pms.c uses kzalloc() and kfree() so it should
include <linux/slab.h> to fix build errors and a warning.
drivers/media/video/pms.c:1047:2: error: implicit declaration of function 'kzalloc'
drivers/media/video/pms.c:1047:6: warning: assignment makes pointer from integer without a cast
drivers/media/video/pms.c:1116:2: error: implicit declaration of function 'kfree'
Found in mmotm but applies to mainline.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to initialize this to false, because the is_rb callback only
ever sets it to true.
Noticed while reading through the code.
Cc: stable@vger.kernel.org
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull slave-dmaengine fixes from Vinod Koul:
"A few fixes in pl330 and imx-sdma drivers."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
DMA: PL330: Fix racy mutex unlock
DMA: PL330: Add missing static storage class specifier
dma: imx-sdma: buf_tail should be initialize in prepare function
dmaengine: pl330: dont complete descriptor for cyclic dma
drivers/media/video/pms.c uses kzalloc() and kfree() so it should
include <linux/slab.h> to fix build errors and a warning.
drivers/media/video/pms.c:1047:2: error: implicit declaration of function 'kzalloc'
drivers/media/video/pms.c:1047:6: warning: assignment makes pointer from integer without a cast
drivers/media/video/pms.c:1116:2: error: implicit declaration of function 'kfree'
Found in mmotm but applies to mainline.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are a number of small fixes for the drivers/staging tree, as well as iio
and pstore drivers (which came from the staging tree in the 3.5-rc1 merge).
All of these are tiny, but resolve issues that people have been reporting.
There's also a documentation update to reflect what the iio drivers really are
doing, which is good to get straightened out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNeAACgkQMUfUDdst+ynNVwCdHCj6smC2JUbvN34gACNrpsYY
WggAoJzQn9mQhwq0pa/ZTpaUOvCFZ39L
=hDkC
-----END PGP SIGNATURE-----
Merge tag 'staging-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging tree fixes from Greg Kroah-Hartman:
"Here are a number of small fixes for the drivers/staging tree, as well
as iio and pstore drivers (which came from the staging tree in the
3.5-rc1 merge). All of these are tiny, but resolve issues that people
have been reporting.
There's also a documentation update to reflect what the iio drivers
really are doing, which is good to get straightened out.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: r8712u: Add new USB IDs
staging: gdm72xx: Release netlink socket properly
iio: drop wrong reference from Kconfig
pstore/inode: Make pstore_fill_super() static
pstore/ram: Should zap persistent zone on unlink
pstore/ram_core: Factor persistent_ram_zap() out of post_init()
pstore/ram_core: Do not reset restored zone's position and size
pstore/ram: Should update old dmesg buffer before reading
staging:iio:ad7298: Fix linker error due to missing IIO kfifo buffer
Revert "staging: usbip: bugfix for stack corruption on 64-bit architectures"
staging: usbip: bugfix for stack corruption on 64-bit architectures
staging/comedi: fix build for USB not enabled
staging: omapdrm: fix crash when freeing bad fb
staging:iio:ad7606: Re-add missing scale attribute
iio: Fix potential use after free
staging:iio: remove num_interrupt_lines from documentation
iio: documentation: Add out_altvoltage and friends
Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNQcACgkQMUfUDdst+yklTQCfZCXFlhA43bZo/8Joqd2pLIIW
2uoAoMze0SlfJeN6Qu7yY0P+qV/f/pc3
=UNFY
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and printk fixes from Greg Kroah-Hartman:
"Here are some fixes for 3.5-rc4 that resolve the kmsg problems that
people have reported showing up after the printk and kmsg changes went
into 3.5-rc1. There are also a smattering of other tiny fixes for the
extcon and hyper-v drivers that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
extcon: max8997: Add missing kfree for info->edev in max8997_muic_remove()
extcon: Set platform drvdata in gpio_extcon_probe() and fix irq leak
extcon: Fix wrong index in max8997_extcon_cable[]
kmsg - kmsg_dump() fix CONFIG_PRINTK=n compilation
printk: return -EINVAL if the message len is bigger than the buf size
printk: use mutex lock to stop syslog_seq from going wild
kmsg - kmsg_dump() use iterator to receive log buffer content
vme: change maintainer e-mail address
Extcon: Don't try to create duplicate link names
driver core: fixup reversed deferred probe order
printk: Fix alignment of buf causing crash on ARM EABI
Tools: hv: verify origin of netlink connector message
Here are some drivers/misc bugfixes (really just drivers/misc/mei/
fixes) for a few problems that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNGgACgkQMUfUDdst+ymmPwCeLxWcEx3UE0pyhwssITArJZz3
WFIAmgPHM66lgXioLxR3swCib9FFo+Xp
=hIWT
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull misc tree updates from Greg Kroah-Hartman:
"Here are some drivers/misc bugfixes (really just drivers/misc/mei/
fixes) for a few problems that have been reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
misc: mei: set WDIOF_ALARMONLY on mei watchdog
misc: mei: Disable MSI when IRQ registration fails
misc: mei: fix stalled read
misc: mei: unregister misc device in pci_remove function
misc: mei: set IRQF_ONESHOT for msi request_threaded_irq
Here are 3 patches resolving a boot regression (the mop500 fix), a build
warning fix, and a kernel-doc fix. All tiny, but should go into the
final 3.5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/iNosACgkQMUfUDdst+ykedgCeLhpFrq5dI19tbhEmCroFs4sx
f+4An29dz2bGkjeViDNkmaBC7msPzLNc
=EBge
-----END PGP SIGNATURE-----
Merge tag 'tty-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull serial driver fixes from Greg Kroah-Hartman:
"Here are 3 patches resolving a boot regression (the mop500 fix), a
build warning fix, and a kernel-doc fix. All tiny, but should go into
the final 3.5 release.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial/amba-pl011: move custom pin control to driver
serial: fix serial_txx9.c build warning/typo
serial: fix kernel-doc warnings in 8250.c
* emailed from Andrew Morton <akpm@linux-foundation.org>: (21 patches)
mm/memblock: fix overlapping allocation when doubling reserved array
c/r: prctl: Move PR_GET_TID_ADDRESS to a proper place
pidns: find_new_reaper() can no longer switch to init_pid_ns.child_reaper
pidns: guarantee that the pidns init will be the last pidns process reaped
fault-inject: avoid call to random32() if fault injection is disabled
Viresh has moved
get_maintainer: Fix --help warning
mm/memory.c: fix kernel-doc warnings
mm: fix kernel-doc warnings
mm: correctly synchronize rss-counters at exit/exec
mm, thp: print useful information when mmap_sem is unlocked in zap_pmd_range
h8300: use the declarations provided by <asm/sections.h>
h8300: fix use of extinct _sbss and _ebss
xtensa: use the declarations provided by <asm/sections.h>
xtensa: use "test -e" instead of bashism "test -a"
xtensa: replace xtensa-specific _f{data,text} by _s{data,text}
memcg: fix use_hierarchy css_is_ancestor oops regression
mm, oom: fix and cleanup oom score calculations
nilfs2: ensure proper cache clearing for gc-inodes
thp: avoid atomic64_read in pmd_read_atomic for 32bit PAE
...
viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with viresh.linux@gmail.com.
It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: Viresh Kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use the correct union for getting the tiling info
- Properly init the PIPE_CONFIG field for SI
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After the change "mac80211: remove spurious BSSID change flag",
BSS_CHANGED_BSSID will not be passed on association or IBSS
status changes. So it could be better to program bssid on ASSOC
or IBSS change notification. Not doing so, is affecting the
packet transmission.
Cc: stable@vger.kernel.org [3.4+]
Reported-by: Michael Leun <lkml20120218@newton.leun.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When debugging is disabled, the event log functions aren't
functional in the way that the debugfs file expects. This
leads to the debugfs access crashing. Since the event log
functions aren't functional then, remove the debugfs file
when CONFIG_IWLWIFI_DEBUG is not set.
Cc: stable@kernel.org
Reported-by: Lekensteyn <lekensteyn@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ath9k: Fix softlockup in AR9485" with commit id
64bc1239c7 fixed the reported
issue, yet its better to avoid the possible infinite loop
in ar9003_get_pll_sqsum_dvc by having a timeout as suggested
by ath9k maintainers.
http://www.spinics.net/lists/linux-wireless/msg92126.html.
Based on my testing PLL's locking measurement is done in
~200us (2 iterations).
Cc: stable@vger.kernel.org
Cc: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes two memory leaks in the SPI initialization code.
Patch based on old maemo patch by:
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Always report beacon loss to the stack, not only when in powersave
state. This is because there's possibility that the driver disables
PSM before it handles old BSS_LOSE_EVENT, so beacon loss has to be
reported.
Patch based on old maemo patch by:
Janne Ylalehto <janne.ylalehto@nokia.com>
Juuso Oikarinen <juuso.oikarinen@nokia.com>
Luciano Coelho <luciano.coelho@nokia.com>
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cast MSB part of current TSF to u64 to prevent loss of most
significant bits. MSB should also be shifted by 32.
Patch based on old maemo patch by:
Yuri Kululin <ext-yuri.kululin@nokia.com>
Yuri Ershov <ext-yuri.ershov@nokia.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull ARM fixes from Russell King:
"This includes three MMCI changes - one to fix up the wrong version of
the DT support patch which was merged, and two to make deferred
probing work. It also includes a fix to the OMAP SPI driver which is
causing a boot time warning.
The remainder are very minor ARM fixes."
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
SPI: fix over-eager devm_xxx() conversion
ARM: 7427/1: mmc: mmci: Defer probe() in case of yet uninitialized GPIOs
ARM: 7426/1: mmc: mmci: Remove wrong error handling of gpio 0
ARM: 7425/1: extable: ensure fixup entries are 4-byte aligned
ARM: 7421/1: bpf_jit: BPF_S_ANC_ALU_XOR_X support
ARM: 7423/1: kprobes: run t32_simulate_ldr_literal() without insn slot
ARM: 7422/1: mmc: mmci: Allocate platform memory during Device Tree boot
- Fixed a 2-line compile error for MXS
- A pure documentation fix for Nomadik
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zNxH
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull two pinctrl fixes from Linus Walleij:
- Fixed a 2-line compile error for MXS
- A pure documentation fix for Nomadik
* tag 'pinctrl-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl/nomadik: document Alt-C glitch
pinctrl: mxs: Use kfree to fix build error
get_voltage_sel() should return selector rather than voltage.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a memory leak that was introduced in the 3.4 kernel. The
leak occurred when FCoE was enabled and traffic was passed over the FCoE
rings reserved for FCoE. The memory leak was due to us not populating the
compound page information on the order 1 pages needed for FCoE.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix Kconfig file to make sure that PTP and IGB/IXGBE are both either
in-kernel or modules, not mixed. Having the build status mixed causes
compile errors.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i210/i211 device has only 16 RAR address filters like 82575, instead of
32 like i350. This patch removes the entries for i210/i211 in the
get_invariants function which was setting them for 32. This ensures that
they will get the default value which is the correct one.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change || check to the intended && when checking the QP type in a
received connection request against the listening endpoint.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
One small bug fix, plus a rename of all the ST Ericsson regulators in
the device tree since all the device trees had been written with
different names and some infelicities in the test proceedures meant that
the device tree code had apparently never actually been run against the
upstream device tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=NS0T
-----END PGP SIGNATURE-----
Merge tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"One small bug fix, plus a rename of all the ST Ericsson regulators in
the device tree since all the device trees had been written with
different names and some infelicities in the test proceedures meant
that the device tree code had apparently never actually been run
against the upstream device tree."
* tag 'regulator-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: Change db8500-prcmu match names to reflect Device Tree
regulator: Change ab8500 match names to reflect Device Tree
regulator: Fix the s5m8767a problem of the division by null
add_virtual_intf() needs to return an ERR_PTR(), instead of NULL,
on errors, otherwise cfg80211 will crash.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"qual" used to be declared on the stack, but then in 998a5a7d6a ("airo:
reduce stack memory footprint") we made it dynamically allocated.
Unfortunately the memcpy() here was missed and it's still copying stack
memory instead of the data that we want. In other words, "&qual" should
be "qual".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When running heavy traffic we stop the tx queue if the pending
packet count reaches certain threshold. Later, the tx queue should
be woken up as soon as the packet count falls below the threshold.
Current code wakes TX queue up on STA interface only. Removing the
check for STA interface will allow both STA and AP interfaces to
resume transmit when tx_pending count becomes low.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
spin_unlock_bh(&txq->lock) already disables softirqs so we don't want
to do it here. Fixes smatch warnings:
drivers/net/wireless/ath/ath5k/base.c:1048 ath5k_drain_tx_buffs() error: double lock 'bottom_half:'
drivers/net/wireless/ath/ath5k/base.c:1056 ath5k_drain_tx_buffs() error: double unlock 'bottom_half:'
Reported-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After setup_frame_info has been called, only info->control.rates is still
valid, other control fields have been overwritten by the ath_frame_info
data. Move the access to info->control.vif for checking short preamble
to setup_frame_info before it gets overwritten.
This regression was introduced in commit d47a61aa
"ath9k: Fix multi-VIF BSS handling"
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Thomas Hühn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: stable@vger.kernel.org [3.4]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate pointer variable for a rate series is used in a loop before it is
initialized. This went unnoticed because it was used earlier for the RTS/CTS
rate. This bug can lead to the wrong PHY type being passed to the
duration calculation function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On a freescale imx6q platform, a hardware phy chip KSZ9021 is
recognized as a KS8001 chip by the current driver like this:
eth0: Freescale FEC PHY driver [Micrel KS8001 or KS8721]
KSZ9021 has phy_id 0x00221610, while KSZ8001 has phy_id
0x0022161a, the current phy_id_mask (0x00fffff0/0x00ffff10) can't
distinguish them. So change phy_id_mask to resolve this problem.
Although the micrel datasheet says that the 4 LSB of phyid2 register
contains the chip revision number and the current driver is designed
to follow this rule, in reality the chip implementation doesn't follow
it.
Cc: David J. Choi <david.choi@micrel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vendor-specific events shall be processed in driver and not sent
to bluetooth stack where they screw up HCI command countings.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
extcon_dev_unregister(info->edev) doest not free info->edev, we need to call
kfree(info->edev) here.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing platform_set_drvdata() in gpio_extcon_probe(), otherwise calling
platform_get_drvdata in gpio_extcon_remove() returns NULL.
Also add missing free_irq call in gpio_extcon_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the index of "Dock-desk" and "Dock-card" are the same.
Thus the latter one overrides the first one.
Then we have problem when calling extcon_find_cable_index() because
edev->supported_cable[7] only matches "Dock-card".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a compiler breakage introduced by commit 8173090acb:
drivers/media/video/pms.c: In function ‘pms_probe’:
drivers/media/video/pms.c:1047:2: error: implicit declaration of function ‘kzalloc’ [-Werror=implicit-function-declaration]
drivers/media/video/pms.c:1116:2: error: implicit declaration of function ‘kfree’ [-Werror=implicit-function-declaration]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed the size of the V4L2_CID_COLORFX control cluster.
Prior to this fix V4L2_CID_ROTATE was also icluded in
the cluster preventing application from enabling rotation.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes the following error:
ERROR: open brace '{' following enum go on the same line
+enum MFC_SHM_OFS
+{
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed s_ctrl function when setting the following controls:
- V4L2_CID_MPEG_VIDEO_DECODER_MPEG4_DEBLOCK_FILTER
- V4L2_CID_MPEG_MFC51_VIDEO_DECODER_H264_DISPLAY_DELAY
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Image size for MFC encoder should have size between
8x4 and 1920x1080 with even width and height.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch corrects definition of H264 level control and
changes bare numbers to enums in two other cases.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The mem2mem_testdev allows multiple instances to be opened in parallel.
Source and destination queue data are being shared between all
instances, which can lead to kernel oops due to race conditions (most
likely to happen inside device_run()).
Attached patch fixes mentioned problem by storing queue data per device
context.
Signed-off-by: Tomasz Moń <desowin@gmail.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed the code copying timecode/timestamp to corresponding
frames between OUTPUT and CAPTURE.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull EDAC fixes from Mauro Carvalho Chehab.
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
edac: Do alignment logic properly in edac_align_ptr()
mpc85xx_edac: fix error: too few arguments to function 'edac_mc_alloc'
edac: fix the error about memory type detection on SandyBridge
edac: avoid mce decoding crash after edac driver unloaded
Fix an incorrect modulation type bitmask. This allows QAM256 also to be
correctly reported.
Signed-off-by: Janne Huttunen <jahuttun@gmail.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull a crypto fix from Herbert Xu:
"This push fixes another bug in the atmel-rng that made it produce
completely useless output."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
hwrng: atmel-rng - fix data valid check
Fix:
emc2103.c: In function set_pwm_enable:
emc2103.c:463:12: warning: conf_reg may be used uninitialized in this function
by checking the return value from read_u8_from_i2c(). This fixes a real problem,
as conf_reg is really uninitialized if read_u8_from_i2c returns an error.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Key lookups may call read_smc() with a fixed-length key string,
and if the lookup fails, trailing stack content may appear in the
kernel log. Fixed with this patch.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Cc: stable@vger.kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This simply shows a little warning if the board does not have remote
control support. This should make it easier for users to see if they
have misconfigured their system or if the driver simply does not have
rc-support for their card (yet).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Cinergy HTC Stick HD uses the same remote control as the TerraTec
Cinergy XS products. Thus the same keymap could be re-used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This reverts commit d509835e32. That commit
breaks support for the generic pass-through mode in the driver for formats,
not natively supported by it. Besides due to a merge conflict it also breaks
driver compilation:
drivers/media/video/mx2_camera.c: In function 'mx2_camera_set_bus_param':
drivers/media/video/mx2_camera.c:937: error: 'pixfmt' undeclared (first use in this function)
drivers/media/video/mx2_camera.c:937: error: (Each undeclared identifier is reported only once
drivers/media/video/mx2_camera.c:937: error: for each function it appears in.)
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1a77b127ae (OMAP : SPI : use devm_* functions) converted the SPI
device controller state to use devm_kzalloc(). Unfortunately, this
is used against an unbound struct device, which results in the
following when the device is bound to its driver:
------------[ cut here ]------------
WARNING: at /home/rmk/git/linux-rmk/drivers/base/dd.c:257 driver_probe_device+0x78/0x21c()
Modules linked in:
Backtrace:
[<c0017d0c>] (dump_backtrace+0x0/0x10c) from [<c033e208>] (dump_stack+0x18/0x1c) r7:00000000 r6:c01ff28c r5:c040050c r4:00000101
[<c033e1f0>] (dump_stack+0x0/0x1c) from [<c00337ec>] (warn_slowpath_common+0x58/0x70)
[<c0033794>] (warn_slowpath_common+0x0/0x70) from [<c0033828>] (warn_slowpath_null+0x24/0x2c)
[<c0033804>] (warn_slowpath_null+0x0/0x2c) from [<c01ff28c>] (driver_probe_device+0x78/0x21c)
[<c01ff214>] (driver_probe_device+0x0/0x21c) from [<c01ff49c>] (__driver_attach+0x6c/0x90)
[<c01ff430>] (__driver_attach+0x0/0x90) from [<c01fda70>] (bus_for_each_dev+0x58/0x98)
[<c01fda18>] (bus_for_each_dev+0x0/0x98) from [<c01ff0f4>] (driver_attach+0x20/0x28)
[<c01ff0d4>] (driver_attach+0x0/0x28) from [<c01fe2f4>] (bus_add_driver+0xb4/0x230)
[<c01fe240>] (bus_add_driver+0x0/0x230) from [<c01ffb24>] (driver_register+0xac/0x138)
[<c01ffa78>] (driver_register+0x0/0x138) from [<c0215d4c>] (spi_register_driver+0x4c/0x60)
[<c0215d00>] (spi_register_driver+0x0/0x60) from [<c045414c>] (ks8851_init+0x14/0x1c)
[<c0454138>] (ks8851_init+0x0/0x1c) from [<c0008770>] (do_one_initcall+0x9c/0x164)
[<c00086d4>] (do_one_initcall+0x0/0x164) from [<c0436410>] (kernel_init+0x128/0x210)
[<c04362e8>] (kernel_init+0x0/0x210) from [<c0038754>] (do_exit+0x0/0x72c)
---[ end trace 4dcda79f5e89dd84 ]---
ks8851 spi1.0: message enable is 0
ks8851 spi1.0: eth0: revision 0, MAC 08:00:28:01:4d:c6, IRQ 194, has EEPROM
Fix this by partially reverting the original commit.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are four link statuses of a bonding slave, the procfs
code shows a wrong status when using downdelay/updelay:
(slave->link == BOND_LINK_UP) ? "up" : "down"
It doesn't respect the rest two statuses. This patch fixes it.
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As seen on smsc75xx, driver_info->description being longer than 32
characters messes up 'ethtool -i' output.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increasing the hardware statistics structure to accomodate statistics for skyhawk.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify IOCTL error message to print subsystem also.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum size of packet that can be handled by controller including ethernet
header is 65535. Reducing gso_max_size accordingly.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a potential hole when configuring the cycle counter used to
generate the nanosecond time clock. This clock is based off of the SYSTIME
registers along with the TIMINCA registers. The TIMINCA register determines
the increment to be added to the SYSTIME registers every DMA clock tick. This
register needs to be reconfigured whenever the link-speed changes. However,
the value calculated stays the same when link is down and when link is up.
Misconfiguration can occur if the link status changes due to a reset, which
causes the TIMINCA register to be reset. This reset puts the device in an
unstable state where the SYSTIME registers stop incrementing and the PTP
protocol does not function.
The solution is to double check the TIMINCA value and always reset the value
if the register is zero. This prevents a misconfiguration bug that halts the
PHC.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the GPIOs used by the MMCI driver are not registered yet when the driver is
probe()d, they can't be used. This happens if the mmci driver is probed before
the respective GPIO controller (e.g. on the LPC32xx EA3250 board, the PCA9532
GPIO controller would be initialized via DT after mmci). Therefore, we defer
mmci in this case.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Zero is a valid GPIO and shouldn't be handled as an error return code from
of_get_named_gpio(). It was a leftover from old code before getting
pdata->gpio_*() was modified.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
According to the datasheet:
The LDO_CTRL registers are used to set the output voltage of LDO1 and LDO2.
LDO_CTRL[7] and LDO_CTRL[3] are reserved and should always be written to 0.
Thus the mask for TPS65023_LDO_1 and TPS65023_LDO_2 should be 0x07 and 0x70
respectively.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This documentation comment existed in an earlier patch set for
GPIO consolidation, so I'm saving it for maintainability of the
code.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 0bf7481 (pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails)
introduced the following build error:
drivers/pinctrl/pinctrl-mxs.c:140:3: error: implicit declaration of function 'free'
Use kfree function instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the db8500-prcum regulator driver so
this is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The 'name' field in 'struct of_regulator_match' expects to match with
its corresponding regulator device node in the Device Tree. This patch
renames each of the regulators in the ab8500 regulator driver so this
is true.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If ramp_delay is 0, delay value can be divided by zero.
This patch can fix the problem.
Signed-off-by: Sangbeom Kim <sbkim73@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Atom CPUs don't have a register to retrieve TjMax. Detection so far was
incomplete. Use the X86 model ID to improve it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Document the Atom series D2000 and N2000 (Cedar Trail) as being supported.
List and set TjMax for those series.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Document the new Atom series (Tunnel Creek and Medfield) as being
supported, and list TjMax for the Atom E600 series.
Also enable the Atom tjmax heuristic for these Atom CPU models.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "R, Durgadoss" <durgadoss.r@intel.com>
Pull drm fixes from Dave Airlie:
"Radeon is most of the work, one regression, one BUG fix in the new
prime code, some fixes to init code to make streamout not lock up the
hardware, and just some code to enable users to test HDMI audio on
later hw (its off by default).
Intel adds edp edid caching for some strange Dell Vostros that black
screen on startup if keep reading their EDID, and a fix for a DP
regression.
Otherwise fix for via/sis and one to stop udl binding to multiple
non-video usb."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: cache the EDID for eDP panels
Revert "drm/i915/dp: Use auxch precharge value of 5 everywhere"
drm/i915: eDP aux needs vdd
drm/i915: don't enumerate HDMID if an eDP panel is already active on the port
drm/radeon: add support for STRMOUT_BASE_UPDATE on 7xx
drm/radeon: add some additional 6xx/7xx/EG register init
drm/radeon: enable HDMI on DCE5 (AKA NI excluding Aruba)
drm sis: initialize object_idr
drm via: initialize object_idr
drm/radeon/prime: reserve/unreserve around pin
drm/radeon: fix regression in dynpm due to multi-ring rework
vga_switcheroo.h: fix pci_dev warning
drm/udl: only bind to the video devices on the hub.
For some reason one of the dev_err invocations is using a wrong
device so fix that.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: stable@vger.kernel.org
When I2C is not responding it's usually due to a previous
unexpected reset during I2C operation. We release it by
powering down and up the SFP+ module.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- two fixes for s3c-fb by Jingoo Han
(including a fix for a potential division by zero)
- a couple of randconfig fixes by Arnd Bergmann
- a cleanup for bfin_adv7393fb by Emil Goode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)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=0Zkc
-----END PGP SIGNATURE-----
Merge tag 'fbdev-fixes-for-3.5-1' of git://github.com/schandinat/linux-2.6
Pull fbdev fixes from Florian Tobias Schandinat:
- two fixes for s3c-fb by Jingoo Han (including a fix for a potential
division by zero)
- a couple of randconfig fixes by Arnd Bergmann
- a cleanup for bfin_adv7393fb by Emil Goode
* tag 'fbdev-fixes-for-3.5-1' of git://github.com/schandinat/linux-2.6:
video: s3c-fb: fix possible division by zero in s3c_fb_calc_pixclk
video: s3c-fb: clear SHADOWCON register when clearing hardware window registers
drivers/tosa: driver needs I2C and SPI to compile
drivers/savagefb: use mdelay instead of udelay
video/console: automatically select a font
video/ili9320: do not mark exported functions __devexit
drivers/video: use correct __devexit_p annotation
video: bfin_adv7393fb: Convert to kstrtouint_from_user
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: cache the EDID for eDP panels
Revert "drm/i915/dp: Use auxch precharge value of 5 everywhere"
drm/i915: eDP aux needs vdd
drm/i915: don't enumerate HDMID if an eDP panel is already active on the port
They aren't going anywhere, and probing on DDC can cause the panel to
blank briefly, so read them up front and cache them for later queries.
v2: fix potential NULL derefs in intel_dp_get_edid_modes and
intel_dp_get_edid (Jani)
copy full EDID length, including extension blocks (Takashi)
free EDID on teardown (Takashi)
v3: malloc a new EDID buffer that's big enough for the memcpy (Chris)
v4: change handling of NULL EDIDs, just preserve the NULL behavior
across detects and mode list fetches rather than trying to re-fetch
the EDID (Chris)
v5: be glad that Chris is around to remind me to hit C-x C-s before
committing.
References: https://bugs.freedesktop.org/show_bug.cgi?id=46856
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 092945e11c.
This commit prevents a DP screen from properly training the link.
Oddly enough it works, once the machine has been warm-booted with an
older kernel.
According to DP docs this _should_ have been the right precharge time.
Also, the commit that originally introduces this was just general snb
DP enabling and didn't mention any specific reason for this special
value. Whatever, trust the reporter that this makes things worse and
let's just revert it.
v2: Less spelling fail.
Cc: Adam Jackson <ajax@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reported-by: "Wouter M. Koolen" <W.M.Koolen-Wijkstra@cwi.nl>
Buglink: https://lkml.org/lkml/2012/6/14/301
Cc: stable@vger.kernel.org (only for 3.4)
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The new oui probe has been missing these.
This issue has been introduce in
commit 0d19832853
Author: Adam Jackson <ajax@redhat.com>
Date: Mon May 14 16:05:47 2012 -0400
drm/i915/dp: Probe branch/sink OUIs
v2: Do the eDP vdd dance of simply not probing the OUI on eDP panels
as suggested by Chris Wilson.
v3: Fix up the error path fail - I suck.
Cc: Adam Jackson <ajax@redhat.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50808
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Bugreport: http://permalink.gmane.org/gmane.comp.video.dri.devel/69695
Tested-by: Yang Guang <guang.a.yang@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This prevents the HDMI detect functions from poking at an eDP
connected panel, which can lead to trouble.
[danvet: Note that we have some other reports of DP vs. HDMI fighting,
but the general case is a much bigger fish to fry.]
References: https://bugs.freedesktop.org/show_bug.cgi?id=42278
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Required for streamout. Bump drm minor.
Marek v2: fix pkt->count check
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- SMX_SAR_CTL0 needs to be programmed correctly to prevent
problems with memory exports in certain cases.
- VC_ENHANCE needs to be initialized on 6xx/7xx.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
After recent changes HDMI code is ready to be enabled on DCE5. This
patch just changes conditions to execute already present code on DCE5.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Christian König <christian.koenig@amd.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Tested-by: Zoltán Böszörményi <zboszor@pr.hu>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The filed object_idr of struct drm_sis_private was introduced with
commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=6de8a748881f1cd9d795454da2b6db616d5ca3d7 .
The idr_init(&dev->object_name_idr) is called instead of
idr_init(&dev_priv->object_idr) by mistake, leaving object_idr
uninitialized. Correct this.
This patch was not tested because of lack of hardware.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The field obejct_idr of struct drm_via_private was introduced with the
commit http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commitdiff;h=77ee8f3825054f23b17e9c8f728f061defd86cdc .
In that patch idr_init(&dev->object_name_idr) was called instead of
idr_init(&dev_priv->object_idr) by mistake, leaving the dev_priv->object_idr
uninitialized. To be more exact, the object_idr buffer is filled with zeros
because of kzalloc(), but the dev_priv->object_idr.lock spinlock can cause
system freeze at lib/idr.c:move_to_free_list() when spin_lock_irqsave()
is called on this spinlock.
The patch was tested on Clevo D4J, model D410J laptop, on the following
hardware, without AGP kernel module loaded:
# lspci -s 01:00.0 -n
01:00.0 0300: 1106:3108 (rev 01)
# lspci -s 01:00.0 -v
01:00.0 VGA compatible controller: VIA Technologies, Inc. K8M800/K8N800/K8N800A [S3 UniChrome Pro] (rev 01) (prog-if 00 [VGA controller])
Subsystem: CLEVO/KAPOK Computer Device 4702
Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 16
Memory at f0000000 (32-bit, prefetchable) [size=64M]
Memory at d1000000 (32-bit, non-prefetchable) [size=16M]
Expansion ROM at <unassigned> [disabled]
Capabilities: [60] Power Management version 2
Capabilities: [70] AGP version 3.0
Signed-off-by: Márton Németh <nm127@freemail.hu>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
I finally got to test this code a bit more and hit the ttm
no reserved assert, so add the reservations around the pinning.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Not all asics have all rings, so make sure the ring is ready
before attempting to check it in the dynpm work handler.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=43367
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is a couple of minor fixes, one for a preempt warning in the mpt2sas
driver and one is a config failure with the new sd async domain.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJP2fuGAAoJEDeqqVYsXL0Md88IAMw1nLZkg39TzEM4tAkkCa4C
o3e3xcmUdO1lqswmgUDaD95Z0H9MUBxwHWQGiAQ7fheuyXXyGOLINkBTx7wOGksk
JpsjEHNhVwW2rxFwZDLYxvtBjRy9E6wJPeuBQxQdU2gGVzjmk2bAV6mJnf+/wDkH
uqJKnrmVNU7x5drw1wP2z0i3zm8UZVlB+eW3J5ReZzfQlpBYWmFcwxrSTp8Q03ko
rx+rMNYlQO+5Cp0/UZxdIlTw4TTaU+F6bXC8jPzZ2zj0mUWtBxiF6rYZQlebNM5n
/byCuivfM9OMeWaiwk5ERIQ/1iOUF4L5apCNUIG2PFtS7RY4349luWpBoeYkaVY=
=eNSh
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a couple of minor fixes, one for a preempt warning in the
mpt2sas driver and one is a config failure with the new sd async
domain."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] Fix sd_probe_domain config problem
[SCSI] mpt2sas: Fix unsafe using smp_processor_id() in preemptible
- When booting as PVHVM we would try to use PV console - but would not validate
the parameters causing us to crash during restore b/c we re-use the wrong event
channel.
- When booting on machines with SR-IOV PCI bridge we didn't check for the bridge
and tried to use it.
- Under AMD machines would advertise the APERFMPERF resulting in needless amount
of MSRs from the guest.
- A global value (xen_released_pages) was not subtracted at bootup when pages
were added back in. This resulted in the balloon worker having the wrong
account of how many pages were truly released.
- Fix dead-lock when xen-blkfront is run in the same domain as xen-blkback.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJP2kcmAAoJEFjIrFwIi8fJXLcH/0a2m6KMcyjc4WaCHspAEFDL
9B055QUFDEOlH55wE2QeED/8D+0HUbTYnQBycH126XLKzLfRv1fsrKFKDSA/SWW2
Mh8N316UrY5Wc3KMdxXdCXJCDqDs7VhARTv6JdlUqUlH9oLRYE6CMRO8MujT0iwd
r+uEnNuW0udMFt8x9SnJW7pEaq7u2N5koEGdWEzZhfoumDaCRxm5OKAKXZ0DZlEZ
/BPjTW/N+Pf4u+bJZY+wQq41y4zGMqu7TDo/hOpuGZxeqtVnCE9trBbuGLnp4K+W
n4TfZZs9Y1kovSMj6qTeB0aP0F77tqHyXPb1oPKxm2kWfqT2dFtIRpuLtXYSC+o=
=cQl2
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.5-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull five Xen bug-fixes from Konrad Rzeszutek Wilk:
- When booting as PVHVM we would try to use PV console - but would not validate
the parameters causing us to crash during restore b/c we re-use the wrong event
channel.
- When booting on machines with SR-IOV PCI bridge we didn't check for the bridge
and tried to use it.
- Under AMD machines would advertise the APERFMPERF resulting in needless amount
of MSRs from the guest.
- A global value (xen_released_pages) was not subtracted at bootup when pages
were added back in. This resulted in the balloon worker having the wrong
account of how many pages were truly released.
- Fix dead-lock when xen-blkfront is run in the same domain as xen-blkback.
* tag 'stable/for-linus-3.5-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: mark local pages as FOREIGN in the m2p_override
xen/setup: filter APERFMPERF cpuid feature out
xen/balloon: Subtract from xen_released_pages the count that is populated.
xen/pci: Check for PCI bridge before using it.
xen/events: Add WARN_ON when quick lookup found invalid type.
xen/hvc: Check HVM_PARAM_CONSOLE_[EVTCHN|PFN] for correctness.
xen/hvc: Fix error cases around HVM_PARAM_CONSOLE_PFN
xen/hvc: Collapse error logic.
Here are a bunch of tiny fixes for the USB core and drivers for 3.5-rc3
A bunch of gadget fixes, and new device ids, as well as some fixes for a number
of different regressions that have been reported recently. We also fixed some
PCI host controllers to resolve a long-standing bug with a whole class of host
controllers that have been plaguing people for a number of kernel releases,
preventing their systems from suspending properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk/byIEACgkQMUfUDdst+ykLBwCgiAi/cS4ObblcBEbnBvosPgsA
PqEAoJLMAwhcozeEOWLhb++45Vs+UjKv
=HAWc
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a bunch of tiny fixes for the USB core and drivers for
3.5-rc3
A bunch of gadget fixes, and new device ids, as well as some fixes for
a number of different regressions that have been reported recently.
We also fixed some PCI host controllers to resolve a long-standing bug
with a whole class of host controllers that have been plaguing people
for a number of kernel releases, preventing their systems from
suspending properly.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (41 commits)
USB: fix gathering of interface associations
usb: ehci-sh: fix illegal phy_init() running when platform_data is NULL
usb: cdc-acm: fix devices not unthrottled on open
Fix OMAP EHCI suspend/resume failure (i693)
USB: ohci-hub: Mark ohci_finish_controller_resume() as __maybe_unused
usb: use usb_serial_put in usb_serial_probe errors
USB: EHCI: Fix build warning in xilinx ehci driver
USB: fix PS3 EHCI systems
xHCI: Increase the timeout for controller save/restore state operation
xhci: Don't free endpoints in xhci_mem_cleanup()
xhci: Fix invalid loop check in xhci_free_tt_info()
xhci: Fix error path return value.
USB: Checking the wrong variable in usb_disable_lpm()
usb-storage: Add 090c:1000 to unusal-devs
USB: serial-generic: use a single set of device IDs
USB: serial: Enforce USB driver and USB serial driver match
USB: add NO_D3_DURING_SLEEP flag and revert 151b612847
USB: option: add more YUGA device ids
USB: mos7840: Fix compilation of usb serial driver
USB: option: fix memory leak
...
Pull IDE fixes from David S. Miller:
1) Two fixes to icside, one for a build failure and another for a
warning. From Christian Dietrich.
2) Fix a bit operation that did erroneous masking, from Julia Lawall.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/ide:
drivers/ide/ide-cs.c: adjust suspicious bit operation
ide: icside.c: fix printk format string compile warning
ide: icside.c: Fix compile with CONFIG_BLK_DEV_IDEDMA_ICS=n
Pull target updates from Nicholas Bellinger:
"This series contains post merge qla_target.c / tcm_qla2xxx bugfixes
from the past weeks, including the patch to allow target-core to use
an optional session shutdown callback to help address an active I/O
shutdown bug in tcm_qla2xxx code (Joern).
Also included is a target regression bugfix releated to explict ALUA
target port group CDB emulation that is CC'ed to stable (Roland)."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
qla2xxx: Remove version.h header file inclusion
tcm_qla2xxx: Handle malformed wwn strings properly
tcm_qla2xxx: tcm_qla2xxx_handle_tmr() can be static
qla2xxx: Don't leak commands we give up on in qlt_do_work()
qla2xxx: Don't crash if we can't find cmd for failed CTIO
tcm_qla2xxx: Don't insert nacls without sessions into the btree
target: Return error to initiator if SET TARGET PORT GROUPS emulation fails
tcm_qla2xxx: Clear session s_id + loop_id earlier during shutdown
tcm_qla2xxx: Convert to TFO->put_session() usage
target: Add TFO->put_session() caller for HW fabric session shutdown
The adapter->npars[] array has QLCNIC_MAX_PCI_FUNC elements. We
allocate it that way a few lines earlier in the function. So this test
is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a off by one error in the minimal number of BD in
bnx2x_start_xmit() and bnx2x_tx_int() before stopping/resuming tx queue.
A full size GSO packet, with data included in skb->head really needs
(MAX_SKB_FRAGS + 4) BDs, because of bnx2x_tx_split()
This error triggers if BQL is disabled and heavy TCP transmit traffic
occurs.
bnx2x_tx_split() definitely can be called, remove a wrong comment.
Reported-by: Tomas Hruby <thruby@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(CAN_CTRLMODE_LISTENONLY & CAN_CTRLMODE_LOOPBACK) is (0x02 & 0x01) which
is zero so the condition is never true. The intent here was to test
that both flags were set.
Cc: <stable@kernel.org> # 2.6.39+
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide an iterator to receive the log buffer content, and convert all
kmsg_dump() users to it.
The structured data in the kmsg buffer now contains binary data, which
should no longer be copied verbatim to the kmsg_dump() users.
The iterator should provide reliable access to the buffer data, and also
supports proper log line-aware chunking of data while iterating.
Signed-off-by: Kay Sievers <kay@vrfy.org>
Tested-by: Tony Luck <tony.luck@intel.com>
Reported-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Tested-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are two new devices for this driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of ep_dequeue , if dequeued request was submitted for dma
transfer, then endpoint is stopped. Once endpoint is stooped, callback
for the dequeued request must be called.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When matching devices against an OF device ID table, the first string of
the compatible property that is listed in the table should match,
regardless of its position in the table.
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The documentation lives in drivers/staging/iio/Documentation, but
according to Jonathan it's obsolete and needs fixing.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't create a link from the device to the compatibility switch class
since we already create a link from the device to to the extcon class
object and we try to use the same name for both links. This causes a loud
complaint from sysfs on boot.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TEAC's UD-H01 (and probably other devices) have a gap in the interface
number allocation of their descriptors:
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 220
bNumInterfaces 3
[...]
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
[...]
Interface Association:
bLength 8
bDescriptorType 11
bFirstInterface 2
bInterfaceCount 2
bFunctionClass 1 Audio
bFunctionSubClass 0
bFunctionProtocol 32
iFunction 4
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
[...]
Once a configuration is selected, usb_set_configuration() walks the
known interfaces of a given configuration and calls find_iad() on
each of them to set the interface association pointer the interface
is included in.
The problem here is that the loop variable is taken for the interface
number in the comparison logic that gathers the association. Which is
fine as long as the descriptors are sane.
In the case above, however, the logic gets out of sync and the
interface association fields of all interfaces beyond the interface
number gap are wrong.
Fix this by passing the interface's bInterfaceNumber to find_iad()
instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: bEN <ml_all@circa.be>
Reported-by: Ivan Perrone <ivanperrone@hotmail.com>
Tested-by: ivan perrone <ivanperrone@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the platform_data is not set, pdata will be uninitialized value.
Since the driver has the following code, if the condition is true when
the pdata is uninitialized value, the driver may jump to the illegal
phy_init().
if (pdata && pdata->phy_init)
pdata->phy_init();
This patch also fixes the following warning:
CC drivers/usb/host/ehci-hcd.o
drivers/usb/host/ehci-sh.c: In function ‘ehci_hcd_sh_probe’:
drivers/usb/host/ehci-sh.c:104: warning: ‘pdata’ may be used uninitialized in this function
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently CDC-ACM devices stay throttled when their TTY is closed while
throttled, stalling further communication attempts after the next open.
Unthrottling during open/activate got lost starting with kernel
3.0.0 and this patch reintroduces it.
Signed-off-by: Otto Meta <otto.patches@sister-shadow.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dev->sgid_tbl[] array is allocated in ocrdma_alloc_resources().
It has OCRDMA_MAX_SGID elements so the test here is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
When booting with Device Tree enabled, platform specific information
is gathered by parsing the DT binary. Platform data is subsequently
populated with the result. The memory required for this is not
automatically allocated during Device Tree boot, so we'll do it here
instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- section markup fixes
- clk_prepare() fix to conform to the clk API
- memory leaks
- incorrect debug messages
- bad errorpaths
- typos
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=F/II
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pinctrl fixes from Linus Walleij:
- section markup fixes
- clk_prepare() fix to conform to the clk API
- memory leaks
- incorrect debug messages
- bad errorpaths
- typos
* tag 'pinctrl-fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: pinctrl-mxs: set platform driver data to NULL at errpath and at unregister
pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails
pinctrl: pinctrl-imx: fix incorrect debug message of maps
pinctrl: pinctrl-imx: free if of_get_parent fails to get the parent node
pinctrl: pinctrl-imx: free allocated pinctrl_map structure only once and use kernel facilities for IMX_PMX_DUMP
pinctrl: nomadik: fix up typo
pinctrl: nomadik: add clk_prepare() call
pinctrl: fix a minor harmless typo
pinctrl: sirf: mark of_device_id match table as __devinitconst
- Fix a regression of USB-audio PCM assignment since 3.4
- A few VGA-switcheroo-related fixes for proper HDMI audio enablement
- Fixed the missing initializations of HD-audio verbs, which may have
resulted in various breakage
- Some driver-specific ASoC updates
- A few fixes for the dynamic PCM code
- The addition of pinctrl support for the i.MX audmux which didn't make it
into -rc1 due to cross tree dependency issues
- A few minor fixes in compress API codes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=Hrh7
-----END PGP SIGNATURE-----
Merge tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- Fix a regression of USB-audio PCM assignment since 3.4
- A few VGA-switcheroo-related fixes for proper HDMI audio enablement
- Fixed the missing initializations of HD-audio verbs, which may have
resulted in various breakage
- Some driver-specific ASoC updates
- A few fixes for the dynamic PCM code
- The addition of pinctrl support for the i.MX audmux which didn't make
it into -rc1 due to cross tree dependency issues
- A few minor fixes in compress API codes
* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Don't forget to call init verbs added by fixup list
ALSA: HDA: Pin fixup for Zotac Z68 motherboard
ALSA: compress_core: cleanup pointers on stop
ALSA: compress_core: don't wake up on pause
ALSA: hda - Fix detection of Creative SoundCore3D controllers
vga_switcheroo: Enable/disable audio clients at the right time
ALSA: hda - HDMI Audio init all connectors when VGA-switcheroo is off
vga_switcheroo: Fix error without CONFIG_VGA_SWITCHEROO
ALSA: hda - Fix uninitialized HDMI controllers with VGA-switcheroo
vga_switcheroo: Add a helper function to get the client state
ALSA: usb-audio: Fix substream assignments
ASoC: tegra: add MODULE_DEVICE_TABLE to tegra30_ahub
ASoC: wm2000: Always use a 4s timeout for the firmware
ASoC: dapm: Fix input list to use source widgets
ASoC: dpcm: Fix dpcm_get_be() to check that DAI is BE
ASoC: wm8994: Apply volume updates with clocks enabled
ASoC: wm8994: Ensure all AIFnCLK events are run from the _late variants
ASoC: imx-audmux: add pinctrl support
ASoC: dapm: Fix connected widget capture path query.
Pull networking fixes from David S. Miller:
This has the fix for the wireless issues I ran into the other week as
well as:
1) Fix CAN c_can driver transmit handling resulting in BUG check
triggers, from AnilKumar Ch.
2) Fix packet drop monitor sleeping in atomic context, from Eric
Dumazet.
3) Fix mv643xx_eth driver build regression, from Andrew Lunn.
4) Inetpeer freeing needs an RCU grace period in order to avoid races
during tree invalidation. From Eric Dumazet.
5) Fix endianness bugs in xt_HMARK netfilter module, from Hans
Schillstrom.
6) Add proper module refcounting to l2tp_eth to avoid crash on module
unload, from Eric Dumazet.
7) Fix truncation of neighbour entry dumps due to logic errors in
neigh_dump_info() and friends, from Eric Dumazet.
8) The conversion of fib6_age() to dst_neigh_lookup() accidently
reversed the logic of a flags test, fix from Thomas Graf.
9) Fix checksum configuration in newer sky2 chips, from Stephen
Hemminger.
10) Revert BQL support in NIU driver, doesn't work.
11) l2tp_ip_sendmsg() illegally uses a route without a proper reference.
From Eric Dumazet.
12) be2net driver references an SKB after it's potentially been freed,
also from Eric Dumazet.
13) Fix RCU stalls in dummy net driver init. Also from Eric Dumazet.
14) lpc_eth has several bugs in it's transmit engine leading to packet
leaks and improper queue wakes, from Eric Dumazet.
15) Apply short DMA workaround to more tg3 chips, from Matt Carlson.
16) Add tilegx network driver.
17) Bonding queue mapping for a packet can get corrupted, fix from Eric
Dumazet.
18) Fix bug in netpoll_send_udp() SKB management that can leave garbage
in the payload in certain situations. From Eric Dumazet.
19) bnx2x driver interprets chip RX checksum offload incorrectly in
encapsulation situations. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
bnx2x: fix checksum validation
netpoll: fix netpoll_send_udp() bugs
bonding: Fix corrupted queue_mapping
bonding:record primary when modify it via sysfs
tilegx network driver: initial support
tg3: Apply short DMA frag workaround to 5906
net: stmmac: Fix clock en-/disable calls
lpc_eth: fix tx completion
lpc_eth: add missing ndo_change_mtu()
dummy: fix rcu_sched self-detected stalls
net: Reorder initialization in ip_route_output to fix gcc warning
virtio-net: fix a race on 32bit arches
r8169: avoid NAPI scheduling delay.
net: Make linux/tcp.h C++ friendly (trivial)
netdev: fix drivers/net/phy/ kernel-doc warnings
net/core: fix kernel-doc warnings
be2net: fix a race in be_xmit()
l2tp: fix a race in l2tp_ip_sendmsg()
mac80211: add back channel change flag
NFC: Fix possible NULL ptr deref when getting the name of a socket
...
pl330_update() stores a pointer to the thrd->req that finished, which
contains a pointer to the corresponding pl330_req. This is done with
the pl330_lock held. Then, it iterates through the req_done list,
calling the callback for each of the requests that are done. The
problem is that the driver releases the lock before calling the
callback for each of the callbacks. pl330_submit_req() running in
another processor can then acquire the lock and insert another request
in one of the thrd->req that hasn't been processed yet, replacing the
pointer to pl330_req there. When the callback returns in
pl330_update() and the next rqdone is popped from the list, it
dereferences the pl330_req pointer to the just scheduled pl330_req,
instead of the one that has finished, calling pl330 with the wrong r.
This patch fixes this by storing the pointer to pl330_req directly in
the list.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Its observed with some PHY, the 60Mhz clock gets
cut too soon for OMAP EHCI, leaving OMAP-EHCI in a bad state.
So on starting port suspend, make sure the 60Mhz clock to EHCI
is kept alive using an internal clock, so that EHCi can cleanly
transition its hw state machine on a port suspend.
Its not proven if this is the issue hit on USB3333,
but the symptoms look very similar.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Volodymyr Mieshkov <x0182794@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ohci_finish_controller_resume() is intended to be used in platform specific
drivers ohci-*.c, included from ohci-hcd.c. Some of them don't actually use
ohci_finish_controller_resume(), so mark it as __maybe_unused.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The use of kfree(serial) in error cases of usb_serial_probe
was invalid - usb_serial structure allocated in create_serial()
gets reference of usb_device that needs to be put, so we need
to use usb_serial_put() instead of simple kfree().
Signed-off-by: Jan Safrata <jan.nikitenko@gmail.com>
Acked-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the following warning:
In file included from drivers/usb/host/ehci-hcd.c:1246:0:
drivers/usb/host/ehci-xilinx-of.c:293:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/usb/host/ehci-xilinx-of.c:293:2: warning: (near initialization for 'ehci_hcd_xilinx_of_driver.shutdown') [enabled by default]
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit aaa0ef289a "PS3 EHCI QH
read work-around", Terratec Grabby (em28xx) stopped working with AMD
Geode LX 800 (USB controller AMD CS5536). Since this is a PS3 only
fix, the following patch adds a conditional block around it.
Signed-off-by: Ricardo Martins <rasm@fe.up.pt>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hi Greg,
Here's five bug fixes for 3.5. They fix some memory leaks in the
bandwidth calculation code, fix a couple bugs in the USB3 Link PM
patchset, and make system suspend and resume work on platforms with the
AsMedia ASM1042 xHCI host controller.
Sarah Sharp
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=oodF
-----END PGP SIGNATURE-----
Merge tag 'for-usb-linus-2012-06-13' of git://git.kernel.org/pub/scm/linux/kernel/git/sarah/xhci into usb-linus
xhci: Bug fixes for 3.5
Hi Greg,
Here's five bug fixes for 3.5. They fix some memory leaks in the
bandwidth calculation code, fix a couple bugs in the USB3 Link PM
patchset, and make system suspend and resume work on platforms with the
AsMedia ASM1042 xHCI host controller.
Sarah Sharp
When system software decides to power down the xHC with the intent of
resuming operation at a later time, it will ask xHC to save the internal
state and restore it when resume to correctly recover from a power event.
Two bits are used to enable this operation: Save State and Restore State.
xHCI spec 4.23.2 says software should "Set the Controller Save/Restore
State flag in the USBCMD register and wait for the Save/Restore State
Status flag in the USBSTS register to transition to '0'". However, it does
not define how long software should wait for the SSS/RSS bit to transition
to 0.
Currently the timeout is set to 1ms. There is bug report
(https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1002697)
indicates that the timeout is too short for ASMedia ASM1042 host controller
to save/restore the state successfully. Increase the timeout to 10ms helps to
resolve the issue.
This patch should be backported to stable kernels as old as 2.6.37, that
contain the commit 5535b1d5f8 "USB: xHCI:
PCI power management implementation"
Signed-off-by: Andiry Xu <andiry.xu@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: stable@vger.kernel.org
This patch fixes a few issues introduced in the recent fix
[f8a9e72d: USB: fix resource leak in xhci power loss path]
- The endpoints listed in bw table are just links and each entry is an
array member of dev->eps[]. But the commit above adds a kfree() call
to these instances, and thus it results in memory corruption.
- It clears only the first entry of rh_bw[], but there can be multiple
ports.
- It'd be safer to clear the list_head of ep as well, not only
removing from the list, as it's checked in
xhci_discover_or_reset_device().
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce6 "xhci: Store
information about roothubs and TTs."
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Oliver Neukum <oneukum@suse.de>
Cc: <stable@vger.kernel.org>
xhci_free_tt_info() may access the invalid memory when it removes the
last entry but the list is not empty. Then tt_next reaches to the
list head but it still tries to check the tt_info of that entry.
This patch fixes the bug and cleans up the messy code by rewriting
with a simple list_for_each_entry_safe().
This patch should be backported to kernels as old as 3.2, that contain
the commit 839c817ce6 "xhci: Store
information about roothubs and TTs."
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Oliver Neukum <oneukum@suse.de>
Cc: <stable@vger.kernel.org>
This patch fixes an issue discovered by Dan Carpenter:
The patch 3b3db02641: "xhci: Add infrastructure for host-specific
LPM policies." from May 9, 2012, leads to the following warning:
drivers/usb/host/xhci.c:3909 xhci_get_timeout_no_hub_lpm()
warn: signedness bug returning '-22'
3906 default:
3907 dev_warn(&udev->dev, "%s: Can't get timeout for non-U1 or U2 state.\n",
3908 __func__);
3909 return -EINVAL;
^^^^^^^^^^^^^^
This should be a u16 like USB3_LPM_DISABLED or something.
3910 }
3911
3912 if (sel <= max_sel_pel && pel <= max_sel_pel)
3913 return USB3_LPM_DEVICE_INITIATED;
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
We check "u1_params" instead of checking "u2_params".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This device gives a bogus answer to get_capacity(16):
[ 8628.278614] scsi 8:0:0:0: Direct-Access USB 2.0 USB Flash Drive 1100 PQ: 0 ANSI: 4
[ 8628.279452] sd 8:0:0:0: Attached scsi generic sg4 type 0
[ 8628.280338] sd 8:0:0:0: [sdd] 35747322042253313 512-byte logical blocks: (18.3 EB/15.8 EiB)
So set the quirk flag to avoid using get_capacity(16) with it:
[11731.386014] usb-storage 2-1.6:1.0: Quirks match for vid 090c pid 1000: 80000
[11731.386075] scsi9 : usb-storage 2-1.6:1.0
[11731.386172] usbcore: registered new interface driver usb-storage
[11731.386175] USB Mass Storage support registered.
[11732.387394] scsi 9:0:0:0: Direct-Access USB 2.0 USB Flash Drive 1100 PQ: 0 ANSI: 4
[11732.388462] sd 9:0:0:0: Attached scsi generic sg3 type 0
[11732.389432] sd 9:0:0:0: [sdc] 7975296 512-byte logical blocks: (4.08 GB/3.80 GiB)
Which makes the capacity look a lot more sane :)
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Simon Raffeiner <sturmflut@lieberbiber.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bnx2x driver incorrectly sets ip_summed to CHECKSUM_UNNECESSARY on
encapsulated segments. TCP stack happily accepts frames with bad
checksums, if they are inside a GRE or IPIP encapsulation.
Our understanding is that if no IP or L4 csum validation was done by the
hardware, we should leave ip_summed as is (CHECKSUM_NONE), since
hardware doesn't provide CHECKSUM_COMPLETE support in its cqe.
Then, if IP/L4 checksumming was done by the hardware, set
CHECKSUM_UNNECESSARY if no error was flagged.
Patch based on findings and analysis from Robert Evans
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mei watchdog doesn't reboot the system it only produces event
therefore mark it as WDIOF_ALARMONLY.
This patch depends on:
commit 2bbeed016d
Author: Alan Cox <alan@linux.intel.com>
watchdog: Add a flag to indicate the watchdog doesn't reboot things
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since MSI is enabled right before that, we should disable it when
registration fails.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb-serial-generic driver uses different device IDs for its USB
matching and its serial matching. This can lead to problems: The
driver can end up getting bound to a USB interface without being
allowed to bind to the corresponding serial port.
This patch (as1557) fixes the problem by using the same device ID
table (the one that can be altered by the "vendor=" and "product="
module parameters) for both purposes. The unused table is removed.
Now the driver will bind only to the intended devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to make sure that the USB serial driver we find
matches the USB driver whose probe we are currently
executing. Otherwise we will end up with USB serial
devices bound to the correct serial driver but wrong
USB driver.
An example of such cross-probing, where the usbserial_generic
USB driver has found the sierra serial driver:
May 29 18:26:15 nemi kernel: [ 4442.559246] usbserial_generic 4-4:1.0: Sierra USB modem converter detected
May 29 18:26:20 nemi kernel: [ 4447.556747] usbserial_generic 4-4:1.2: Sierra USB modem converter detected
May 29 18:26:25 nemi kernel: [ 4452.557288] usbserial_generic 4-4:1.3: Sierra USB modem converter detected
sysfs view of the same problem:
bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root 0 May 29 18:23 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/sierra/
total 0
--w------- 1 root root 4096 May 29 18:23 bind
lrwxrwxrwx 1 root root 0 May 29 18:23 module -> ../../../../module/sierra
-rw-r--r-- 1 root root 4096 May 29 18:23 new_id
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0/ttyUSB0
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB1 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2/ttyUSB1
lrwxrwxrwx 1 root root 0 May 29 18:32 ttyUSB2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3/ttyUSB2
--w------- 1 root root 4096 May 29 18:23 uevent
--w------- 1 root root 4096 May 29 18:23 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb/drivers/usbserial_generic/
total 0
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.0 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.0
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.2 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.2
lrwxrwxrwx 1 root root 0 May 29 18:33 4-4:1.3 -> ../../../../devices/pci0000:00/0000:00:1d.7/usb4/4-4/4-4:1.3
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root 0 May 29 18:33 module -> ../../../../module/usbserial
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind
bjorn@nemi:~$ ls -l /sys/bus/usb-serial/drivers/generic/
total 0
--w------- 1 root root 4096 May 29 18:33 bind
lrwxrwxrwx 1 root root 0 May 29 18:33 module -> ../../../../module/usbserial
-rw-r--r-- 1 root root 4096 May 29 18:33 new_id
--w------- 1 root root 4096 May 29 18:22 uevent
--w------- 1 root root 4096 May 29 18:33 unbind
So we end up with a mismatch between the USB driver and the
USB serial driver. The reason for the above is simple: The
USB driver probe will succeed if *any* registered serial
driver matches, and will use that serial driver for all
serial driver functions.
This makes ref counting go wrong. We count the USB driver
as used, but not the USB serial driver. This may result
in Oops'es as demonstrated by Johan Hovold <jhovold@gmail.com>:
[11811.646396] drivers/usb/serial/usb-serial.c: get_free_serial 1
[11811.646443] drivers/usb/serial/usb-serial.c: get_free_serial - minor base = 0
[11811.646460] drivers/usb/serial/usb-serial.c: usb_serial_probe - registering ttyUSB0
[11811.646766] usb 6-1: pl2303 converter now attached to ttyUSB0
[11812.264197] USB Serial deregistering driver FTDI USB Serial Device
[11812.264865] usbcore: deregistering interface driver ftdi_sio
[11812.282180] USB Serial deregistering driver pl2303
[11812.283141] pl2303 ttyUSB0: pl2303 converter now disconnected from ttyUSB0
[11812.283272] usbcore: deregistering interface driver pl2303
[11812.301056] USB Serial deregistering driver generic
[11812.301186] usbcore: deregistering interface driver usbserial_generic
[11812.301259] drivers/usb/serial/usb-serial.c: usb_serial_disconnect
[11812.301823] BUG: unable to handle kernel paging request at f8e7438c
[11812.301845] IP: [<f8e38445>] usb_serial_disconnect+0xb5/0x100 [usbserial]
[11812.301871] *pde = 357ef067 *pte = 00000000
[11812.301957] Oops: 0000 [#1] PREEMPT SMP
[11812.301983] Modules linked in: usbserial(-) [last unloaded: pl2303]
[11812.302008]
[11812.302019] Pid: 1323, comm: modprobe Tainted: G W 3.4.0-rc7+ #101 Dell Inc. Vostro 1520/0T816J
[11812.302115] EIP: 0060:[<f8e38445>] EFLAGS: 00010246 CPU: 1
[11812.302130] EIP is at usb_serial_disconnect+0xb5/0x100 [usbserial]
[11812.302141] EAX: f508a180 EBX: f508a180 ECX: 00000000 EDX: f8e74300
[11812.302151] ESI: f5050800 EDI: 00000001 EBP: f5141e78 ESP: f5141e58
[11812.302160] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[11812.302170] CR0: 8005003b CR2: f8e7438c CR3: 34848000 CR4: 000007d0
[11812.302180] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[11812.302189] DR6: ffff0ff0 DR7: 00000400
[11812.302199] Process modprobe (pid: 1323, ti=f5140000 task=f61e2bc0 task.ti=f5140000)
[11812.302209] Stack:
[11812.302216] f8e3be0f f8e3b29c f8e3ae00 00000000 f513641c f5136400 f513641c f507a540
[11812.302325] f5141e98 c133d2c1 00000000 00000000 f509c400 f513641c f507a590 f5136450
[11812.302372] f5141ea8 c12f0344 f513641c f507a590 f5141ebc c12f0c67 00000000 f507a590
[11812.302419] Call Trace:
[11812.302439] [<c133d2c1>] usb_unbind_interface+0x51/0x190
[11812.302456] [<c12f0344>] __device_release_driver+0x64/0xb0
[11812.302469] [<c12f0c67>] driver_detach+0x97/0xa0
[11812.302483] [<c12f001c>] bus_remove_driver+0x6c/0xe0
[11812.302500] [<c145938d>] ? __mutex_unlock_slowpath+0xcd/0x140
[11812.302514] [<c12f0ff9>] driver_unregister+0x49/0x80
[11812.302528] [<c1457df6>] ? printk+0x1d/0x1f
[11812.302540] [<c133c50d>] usb_deregister+0x5d/0xb0
[11812.302557] [<f8e37c55>] ? usb_serial_deregister+0x45/0x50 [usbserial]
[11812.302575] [<f8e37c8d>] usb_serial_deregister_drivers+0x2d/0x40 [usbserial]
[11812.302593] [<f8e3a6e2>] usb_serial_generic_deregister+0x12/0x20 [usbserial]
[11812.302611] [<f8e3acf0>] usb_serial_exit+0x8/0x32 [usbserial]
[11812.302716] [<c1080b48>] sys_delete_module+0x158/0x260
[11812.302730] [<c110594e>] ? mntput+0x1e/0x30
[11812.302746] [<c145c3c3>] ? sysenter_exit+0xf/0x18
[11812.302746] [<c107777c>] ? trace_hardirqs_on_caller+0xec/0x170
[11812.302746] [<c145c390>] sysenter_do_call+0x12/0x36
[11812.302746] Code: 24 02 00 00 e8 dd f3 20 c8 f6 86 74 02 00 00 02 74 b4 8d 86 4c 02 00 00 47 e8 78 55 4b c8 0f b6 43 0e 39 f8 7f a9 8b 53 04 89 d8 <ff> 92 8c 00 00 00 89 d8 e8 0e ff ff ff 8b 45 f0 c7 44 24 04 2f
[11812.302746] EIP: [<f8e38445>] usb_serial_disconnect+0xb5/0x100 [usbserial] SS:ESP 0068:f5141e58
[11812.302746] CR2: 00000000f8e7438c
Fix by only evaluating serial drivers pointing back to the
USB driver we are currently probing. This still allows two
or more drivers to match the same device, running their
serial driver probes to sort out which one to use.
Cc: stable@vger.kernel.org # 3.0, 3.2, 3.3, 3.4
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This bug caused severe connectivity issue in the LMS application
(LMS is described in Documentation/misc-devices/mei/mei.txt)
The bug was introduced in patch:
commit 1ccb7b6249
staging/mei: propagate error codes up in the write flow
The patch has reverted the return value logic of some fo function but
the conditional in _mei_irq_thread_read function was not swapped
making read always entering the error path
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the misc device is registered only in the pci probe function
it has to be also unregistered in the counterpart pci remove function
and not in the module exit function.
In case of probe failure the driver was oopsing in module exit function.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
when the default irq quick handler is used then IRQF_ONESHOT must be set
otherwise the request fails and following error is displayed:
genirq: Threaded irq requested with handler=NULL and !ONESHOT for irq ...
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If driver requests probe deferral,
it will be added to deferred_probe_pending_list
by driver_deferred_probe_add(), but, it used list_add().
Because of that, deferred probe will be run as reversed order.
This patch uses list_add_tail(), and solved this issue.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.15 (GNU/Linux)
iEYEABECAAYFAk/YA2QACgkQGkmNcg7/o7iquwCg1dTXMRl6iC+/nGrfBylFhbvQ
IjQAnj/+piJJlqdN8HDPnnXOvbcgZLNk
=hO8d
-----END PGP SIGNATURE-----
Merge tag 'sh-for-linus' of git://github.com/pmundt/linux-sh
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
sh: Kill off additional asm-generic wrappers.
sh: Setup CROSS_COMPILE at the top
sh: Fix up link time defsym warnings.
sh: use the new generic strnlen_user() function
sh: switch to generic strncpy_from_user().
sh: Kill off last dead UBC header
serial: sh-sci: Make probe fail for ports that exceed the maximum count
serial: sh-sci: Fix probe error paths
clocksource: sh_tmu: Use clockevents_config_and_register().
clocksource: sh_tmu: Convert timer lock to raw spinlock.
clocksource: sh_mtu2: Convert timer lock to raw spinlock.
clocksource: sh_cmt: Convert timer lock to raw spinlock.
bug.h: need linux/kernel.h for TAINT_WARN.
sh: convert to kbuild asm-generic support.
sh64: Fix up fallout from generic init_task conversion.
sh: arch/sh/kernel/process.c needs asm/fpu.h for unlazy_fpu().
Pull led fixes from Bryan Wu.
* 'fixes-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
leds: Make LEDS_ASIC3 and LEDS_RENESAS_TPU depend on LEDS_CLASS=y
leds: fixed a coding style issue.
leds: don't disable blinking when writing the same value to delay_on or delay_off
This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
A similar patch has already been applied as commit
151b612847 (USB: EHCI: fix crash during
suspend on ASUS computers). The patch supersedes that one and reverts
it. There are two differences:
The old patch added the flag at the USB level; this patch
adds it at the PCI level.
The old patch applied to all chipsets with the same vendor,
subsystem vendor, and product IDs; this patch makes an
exception for a known-good system (based on DMI information).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dâniel Fraga <fragabr@gmail.com>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix a regression introduced by 7eaceaccab ("block: remove per-queue
plugging"). In that patch, Jens removed the whole mm_unplug_device()
function, which used to be the trigger to make umem start to work.
We need to implement unplugging to make umem start to work, or I/O will
never be triggered.
Signed-off-by: Tao Guo <Tao.Guo@emc.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Shaohua Li <shli@kernel.org>
Cc: <stable@vger.kernel.org>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Without this, modules can't use this API, leading to build failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org [3.0+]
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Divider value can be zero and it makes division by zero
from debug message in s3c_fb_calc_pixclk; therefore, it
should be fixed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
All bits of SHADOWCON register should be cleared when clearing
hardware window registers; however, some bits of SHADOWCON register
are not cleared previously.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
debugfs or omapdss debug support is turned off, and fixes a suspend related
crash.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yO72
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux
Pull omapdss build problem fix from Tomi Valkeinen:
"Small fixes for omapdss driver. Most importantly, fixes a build
problem when debugfs or omapdss debug support is turned off, and fixes
a suspend related crash."
This has apparently been annoying rmk for a while..
* tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux:
OMAPDSS: fix registration of DPI and SDI devices
OMAPDSS: DSI: Fix bug when calculating LP command interleaving parameters
OMAPDSS: fix bogus WARN_ON in dss_runtime_put()
OMAPDSS: Taal: fix compilation warning
OMAPDSS: fix build when DEBUG_FS or DSS_DEBUG_SUPPORT disabled
version.h header file is no longer required for qla_target code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If we make a variable an unsigned int and then expect it to be < 0 on
a bad character, we're going to have a bad time. Fix the tcm_qla2xxx
code to actually notice if hex_to_bin() returns a negative variable.
This was detected by the compiler warning:
scsi/qla2xxx/tcm_qla2xxx.c: In function ‘tcm_qla2xxx_npiv_extract_wwn’:
scsi/qla2xxx/tcm_qla2xxx.c:148:3: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits]
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If we go to the "out_term:" exit path in qlt_do_work(), we call
qlt_send_term_exchange() with a NULL cmd, which means that it can't
possibly free the cmd for us. Add an explicit call to free the
command memory, so we don't leak the allocation.
This will also fix warnings about "BUG qla_tgt_cmd_cachep: Objects
remaining on kmem_cache_close" from slub when unloading the qla2xxx
target module.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In qlt_do_ctio_completion(), there's no point in calling
qlt_term_ctio_exchange() with a NULL cmd -- all that it does is crash
in a NULL pointer dereference, since it does
qlt_send_term_exchange(vha, cmd, &cmd->atio, 1);
and dereferencing &cmd->atio is a bad idea if cmd itself is NULL.
If we really need to do this, we could take the values from the
failed CTIO we're processing, but it's not clear if it's worth
the replumbing to do that.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
When we create an explicit node ACL in tcm_qla2xxx_make_nodeacl(),
there is a call to tcm_qla2xxx_setup_nacl_from_rport(), which puts the
node ACL into the lport_fcport_map even though there is no session yet
for the initiator. Since the only time we remove entries from this
map is when we free a session, this means that if we later delete this
node ACL without the initiator ever creating a session, we'll leave
the nacl pointer in the btree pointing at freed memory.
This is especially bad if that initiator later does send us a command
that would cause us to create a dynamic ACL and session: we'll find
the stale freed nacl pointer in the btree and end up with use-after-free.
We could add more code to clear the btree entry when deleting the
explicit nacl, but the original insertion is pointless: without a
session attached, we'll just have to update the entry when a session
appears anyway. So we can just delete tcm_qla2xxx_setup_nacl_from_rport()
and the code that calls it.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The error paths in target_emulate_set_target_port_groups() are all
essentially "rc = -EINVAL; goto out;" but the code at "out:" ignores
rc and always returns success. This means that even if eg explicit
ALUA is turned off, the initiator will always see a good SCSI status
for SET TARGET PORT GROUPS.
Fix this by returning rc as is intended. It appears this bug was
added by the following patch:
commit 05d1c7c0d0
Author: Andy Grover <agrover@redhat.com>
Date: Wed Jul 20 19:13:28 2011 +0000
target: Make all control CDBs scatter-gather
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds a new tcm_qla2xxx_clear_sess_lookup() call to clear session
specific s_id + loop_id entries used for se_node_acl pointer lookup ahead
of releasing se_session within the process context workqueue callback in
tcm_qla2xxx_free_session().
It makes the call in existing tcm_qla2xxx_clear_nacl_from_fcport_map()
code invoked from qlt_unreg_sess() in interrupt context w/ hardware_lock
held, ahead of the process context callback into qlt_free_session_done()
-> tcm_qla2xxx_free_session().
We are doing this to address a race between incoming ATIO or TMR packets
using stale se_node_acl pointer once session shutdown has been invoked via
qlt_unreg_sess() in qla_target.c LLD code, and when the entire tcm_qla2xxx
endpoint has not been forced into shutdown w/ echo 0 > ../$QLA2XXX_PORT/enable
Cc: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch converts tcm_qla2xxx code to use an internal kref_put() for
se_session->sess_kref in order to ensure that qla_hw_data->hardware_lock
can be held while calling qlt_unreg_sess() for the final put.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch adds an optional target_core_fabric_ops->put_session() caller
within the existing target_put_session() code path.
This is required by tcm_qla2xxx code in order to invoke it's own fabric
specific session shutdown handler using se_session->sess_kref.
Signed-off-by: Joern Engel <joern@logfs.org>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The driver supports a maximum number of ports configurable at compile
time. Make sure the probe() method fails when registering a port that
exceeds the maximum instead of returning success without registering the
port.
This fixes a crash at system suspend time, when the driver tried to
suspend a non-registered port using the UART core.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When probing fails, the driver must not try to cleanup resources that
have not been initialized. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The __devinitconst section can't be referenced
from usb_serial_device structure. Thus removed it as
it done in other mos* device drivers.
Error itself:
WARNING: drivers/usb/serial/mos7840.o(.data+0x8): Section mismatch in reference
from the variable moschip7840_4port_device to the variable
.devinit.rodata:id_table
The variable moschip7840_4port_device references
the variable __devinitconst id_table
[v2] no attach now
Signed-off-by: Tony Zelenoff <antonz@parallels.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix memory leak introduced by commit 383cedc3bb ("USB: serial:
full autosuspend support for the option driver") which allocates
usb-serial data but never frees it.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 8b4c6a3ab5 ("USB: option: Use generic USB wwan code")
moved option port-data allocation to usb_wwan_startup but still cast the
port data to the old struct...
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The low level helper returns 1 on success. The ioctl should however return
0. As this is the only user of the helper return, make the helper return 0 or
an error code.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=43009
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Later firmwares for this device now have proper subclass and
protocol info so we can identify it nicely without needing to use
the blacklist. I'm not removing the old 0xff matching as there
may be devices in the field that still need that.
Signed-off-by: Andrew Bird <ajb@spheresystems.co.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for Sierra Wireless AirCard 320U modem
Signed-off-by: Tomas Cassidy <tomas.cassidy@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for RT Systems USB-RTS01 USB to Serial adapter:
http://www.rtsystemsinc.com/Photos/USBRTS01.html
Tested by controlling Icom IC-718 amateur radio transceiver via hamlib.
Signed-off-by: Evan McNabb <evan@mcnabbs.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some additional IDs found in the BSD/GPL licensed out-of-tree
GobiSerial driver from Sierra Wireless.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
IO_DATA_PATH_WIDTH_8 is 0, so a bit-and with it is always false. The
value IO_DATA_PATH_WIDTH covers the bits of the IO_DATA_PATH constants, so
first pick those bits and then make the test using !=.
This problem was found using Coccinelle (http://coccinelle.lip6.fr/).
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had a boot regression in Ux500 in the merge window because
two orthogonal pin control schemes for the PL011 were merged
at the same time:
- One using the .init() and .exit() hooks into the platform
for Ux500 putting the pins into default vs sleep state
respectively as the port was started/stopped.
commit a09806607f
"ARM: ux500: switch to using pinctrl for uart0"
- One hogging the default setting at PL011 probe()
commit 258e055111
"serial: amba-pl011: adopt pinctrl support"
To get a solution that works for both let's scrap the stuff
in the platform callbacks, instead have the driver itself
select default and sleep states when the port is
started/stopped. Hopefully this works for all clients.
Platform callbacks are bad for device tree migration anyway,
so this rids us of another problem in Ux500.
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kconfig symbol test to use "defined":
drivers/tty/serial/serial_txx9.c: warning: "CONFIG_CONSOLE_POLL" is not defined [-Wundef]
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix kernel-doc warnings in drivers/tty/serial/8250/8250.c:
Warning(drivers/tty/serial/8250/8250.c:3128): No description found for parameter 'up'
Warning(drivers/tty/serial/8250/8250.c:3128): Excess function parameter 'port' description in 'serial8250_register_8250_port'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the transmit path of the bonding driver, skb->cb is used to
stash the skb->queue_mapping so that the bonding device can set its
own queue mapping. This value becomes corrupted since the skb->cb is
also used in __dev_xmit_skb.
When transmitting through bonding driver, bond_select_queue is
called from dev_queue_xmit. In bond_select_queue the original
skb->queue_mapping is copied into skb->cb (via bond_queue_mapping)
and skb->queue_mapping is overwritten with the bond driver queue.
Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes
the packet length into skb->cb, thereby overwriting the stashed
queue mappping. In bond_dev_queue_xmit (called from hard_start_xmit),
the queue mapping for the skb is set to the stashed value which is now
the skb length and hence is an invalid queue for the slave device.
If we want to save skb->queue_mapping into skb->cb[], best place is to
add a field in struct qdisc_skb_cb, to make sure it wont conflict with
other layers (eg : Qdiscc, Infiniband...)
This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8
bytes :
netem qdisc for example assumes it can store an u64 in it, without
misalignment penalty.
Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[].
The largest user is CHOKe and it fills it.
Based on a previous patch from Tom Herbert.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Tom Herbert <therbert@google.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we modify primary via sysfs and it is not a valid slave,
we should record it for future use, and this behavior is the same with
bond_check_params().
Signed-off-by: Weiping Pan <wpan@redhat.com>
Acked-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test procedure:
1. Start AP with security setting (e.g. WPA2)
2. Stop AP
3. Start AP with open security
Here it's observed that privacy is enabled in beacons and
probe responses.
This patch fixes it by checking the privacy parameter from
cfg80211_ap_settings. If privacy is not set in cfg80211_ap_settings,
set open authentication and no encryption in FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ad7298 drivers buffer implementation uses the IIO kfifo buffer, so it needs
to select IIO_KFIFO_BUF. Otherwise (if no other driver selects the symbol) the
following linker error will occur:
drivers/built-in.o: In function `ad7298_register_ring_funcs_and_init':
(.text+0x245cf2): undefined reference to `iio_kfifo_allocate'
drivers/built-in.o: In function `ad7298_register_ring_funcs_and_init':
(.text+0x245d7d): undefined reference to `iio_kfifo_free'
drivers/built-in.o: In function `ad7298_ring_cleanup':
(.text+0x245dcd): undefined reference to `iio_kfifo_free'
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 08224262ad as it's
just not right.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable <stable@vger.kernel.org>
Cc: Bart Westgeest <bart@elbrys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
