Add support for the Broadcom Omega SoC internal ethernet switch
to the b53 srab driver in the DSA framework.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow propagating ethtool::rxnfc programming to the CPU/management port
such that it is possible for such a CPU to perform e.g: Wake-on-LAN
using filters configured by the switch. We need a tiny bit of
cooperation between the switch drivers which is able to do the full flow
matching, whereas the CPU/management port might not. The CPU/management
driver needs to return -EOPNOTSUPP to indicate an non critical error,
any other error code otherwise.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are in Wake-on-LAN, we operate with the host sofware not running
a network stack, so we want to the switch to flood packets in order to
cause a system wake-up when matching specific filters (unicast or
multicast). This was not necessary before since we supported Magic
Packet which are targeting a broadcast MAC address which the switch
already floods.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ds->enabled_port_mask only contains a bitmask of user-facing enabled
ports, we also need to allow programming CFP rules that target CPU ports
(e.g: ports 5 and 8).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BTF conflicts were simple overlapping changes.
The virtio_net conflict was an overlap of a fix of statistics counter,
happening alongisde a move over to a bonafide statistics structure
rather than counting value on the stack.
Signed-off-by: David S. Miller <davem@davemloft.net>
Version 1 of the patch adding SERDES support to the 88E6141/6341
correctly added the ops to the 88E6141/6341. However, by the time
version 3 was committed, the ops had moved to the 88E6085/6175. Put
them back where they belong.
Fixes: 5bafeb6e7e ("net: dsa: mv88e6xxx: 88E6141/6341 SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MODULE_LICENSE() to net/dsa/realtek.o to fix build warning message.
WARNING: modpost: missing MODULE_LICENSE() in drivers/net/dsa/realtek.o
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
free_irq() waits until all handlers for this IRQ have completed. As the
relevant handler (mv88e6xxx_g1_irq_thread_fn()) takes the chip's reg_lock
it might never return if the thread calling free_irq() holds this lock.
For the same reason kthread_cancel_delayed_work_sync() in the polling case
must not hold this lock.
Also first free the irq (or stop the worker respectively) such that
mv88e6xxx_g1_irq_thread_work() isn't called any more before the irq
mappings are dropped in mv88e6xxx_g1_irq_free_common() to prevent the
worker thread to call handle_nested_irq(0) which results in a NULL-pointer
exception.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
For slow processors using bit-banging MDIO, 20ms can be too short a
timeout when waiting for the transmit timestamp to become
available. Double it to 40ms.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the 6352 and newer switches, the PTP Ethertype defaults to
ETH_P_1588. Hence it was not explicitly set. The 6165 however defaults
to 0. So explicitly set the EtherType.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6165 family supports a more restricted version of hardware time
stamps. Only L2 PTP is supported. All ports have to use the same
EtherType, and transport spec configuration. PTP can only be
enabled/disabled globally, not per port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6165 only supports layer L2 PTP, where as the more modern devices
also support UDP and UDPv6, i.e. L4. Abstract the supported receive
filters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6165 family does not have per port PTP control registers. Also, it
places the timestamp data in different registers. Abstract the current
implementation of 6352 compatible PTP devices so that 6165 can be
added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6165 family has its global clock in the PTP global
registers. It does not support any form of PTP events. Add a function
to read the clock, fill in an ops structure, and register it with the
two members of the family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MV88E6165 PTP registers are all in AVB bank F, unlike newer
generations which spread them over AVB bank E and F. Implement AVB ops
for the MV88E6165 which hides this difference.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6165 family supports PTP, but its registers use a different
layout to the currently supported devices. Abstract accessing the PTP
registers into a set of ops, so making space for a second
implementation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_DSA_BCM_SF2 does not need to depend on CONFIG_OF anymore since we have
stubs when that option is disabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/dsa/rtl8366.c: In function ‘rtl8366_reset_vlan’:
drivers/net/dsa/rtl8366.c:234:25: warning: unused variable ‘vlan4k’ [-Wunused-variable]
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a driver core for the Realtek SMI chips and a
subdriver for the RTL8366RB. I just added this chip simply
because it is all I can test.
The code is a massaged variant of the code that has been
sitting out-of-tree in OpenWRT for years in the absence of
a proper switch subsystem. This creates a DSA driver for it.
I have tried to credit the original authors wherever
possible.
The main changes I've done from the OpenWRT code:
- Added an IRQ chip inside the RTL8366RB switch to demux and
handle the line state IRQs.
- Distributed the phy handling out to the PHY driver.
- Added some RTL8366RB code that was missing in the driver at
the time, such as setting up "green ethernet" with a funny
jam table and forcing MAC5 (the CPU port) into 1 GBit.
- Select jam table and add the default jam table from the
vendor driver, also for ASIC "version 0" if need be.
- Do not store jam tables in the device tree, store them
in the driver.
- Pick in the "initvals" jam tables from OpenWRT's driver
and make those get selected per compatible for the
whole system. It's apparently about electrical settings
for this system and whatnot, not really configuration
from device tree.
- Implemented LED control: beware of bugs because there are
no LEDs on the device I am using!
We do not implement custom DSA tags. This is explained in
a comment in the driver as well: this "tagging protocol" is
not simply a few extra bytes tagged on to the ethernet
frame as DSA is used to. Instead, enabling the CPU tags
will make the switch start talking Realtek RRCP internally.
For example a simple ping will make this kind of packets
appear inside the switch:
0000 ff ff ff ff ff ff bc ae c5 6b a8 3d 88 99 a2 00
0010 08 06 00 01 08 00 06 04 00 01 bc ae c5 6b a8 3d
0020 a9 fe 01 01 00 00 00 00 00 00 a9 fe 01 02 00 00
0030 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
As you can see a custom "8899" tagged packet using the
protocol 0xa2. Norm RRCP appears to always have this
protocol set to 0x01 according to OpenRRCP. You can also
see that this is not a ping packet at all, instead the
switch is starting to talk network management issues
with the CPU port.
So for now custom "tagging" is disabled.
This was tested on the D-Link DIR-685 with initramfs and
OpenWRT userspaces and works fine on all the LAN ports
(lan0 .. lan3). The WAN port is yet not working.
Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warnings:
drivers/net/dsa/vitesse-vsc73xx.c:1054:6: warning:
symbol 'vsc73xx_get_strings' was not declared. Should it be static?
drivers/net/dsa/vitesse-vsc73xx.c:1113:5: warning:
symbol 'vsc73xx_get_sset_count' was not declared. Should it be static?
drivers/net/dsa/vitesse-vsc73xx.c:1122:6: warning:
symbol 'vsc73xx_get_ethtool_stats' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_err error message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable 'off' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'off' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a DSA driver for:
Vitesse VSC7385 SparX-G5 5-port Integrated Gigabit Ethernet Switch
Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch
Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch
Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch
These switches have a built-in 8051 CPU and can download and execute
firmware in this CPU. They can also be configured to use an external
CPU handling the switch in a memory-mapped manner by connecting to
that external CPU's memory bus.
This driver (currently) only takes control of the switch chip over
SPI and configures it to route packages around when connected to a
CPU port. The chip has embedded PHYs and VLAN support so we model it
using DSA as a best fit so we can easily add VLAN support and maybe
later also exploit the internal frame header to get more direct
control over the switch.
The four built-in GPIO lines are exposed using a standard GPIO chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Broadcom Cygnus SoC, the brcm tag needs to be inserted
in between the mac address and the ether type (should use
'DSA_PROTO_TAG_BRCM') for the packets sent to the internal
b53 switch.
Since the Cygnus was added with the BCM58XX device id and the
BCM58XX uses 'DSA_PROTO_TAG_BRCM_PREPEND', the data path is
broken, due to the incorrect brcm tag location.
Add a new b53 device id (BCM583XX) for Cygnus family to fix the
issue. Add the new device id to the BCM58XX family as Cygnus
is similar to the BCM58XX in most other functionalities.
Fixes: 1160603960 ("net: dsa: b53: Support prepended Broadcom tags")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Reported-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filling in the padding slot in the bpf structure as a bug fix in 'ne'
overlapped with actually using that padding area for something in
'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the BCM5389 switch connected through MDIO.
Signed-off-by: Damien Thébault <damien.thebault@vitec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it explicit that either device tree is used or platform data. If
neither is available, abort the probe.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 877b7cb0b6 ("net: dsa: mv88e6xxx: Add minimal platform_data support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant debug prints from phy_read/write since we can trace those
calls through trace events. Enhance dynamic debug prints to print arguments
which helps figuring how what is going on at the driver level with higher level
configuration interfaces.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix warning reported by checkpatch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the GPLv2 license boilerplate with the SPDX license identifier.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement adjust_link function that allows to overwrite default CPU port
setting using fixed-link device tree subnode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default autonegotiation is enabled to configure MAC on all ports.
For the CPU port autonegotiation can not be used so we need to set
some sensible defaults manually.
This patch forces the default setting of the CPU port to 1000Mbps/full
duplex which is the chip maximum capability.
Also correct size of the bit field used to configure link speed.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is brought up/down do not enable/disable only the TXMAC
but the RXMAC as well. This is essential for the CPU port to work.
Fixes: 6b93fb4648 ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the four-port variant of the Qualcomm QCA833x switch.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
In mv88e6xxx_probe(), ("np" or "pdata") might be an invariant
but GCC can't see that, therefore:
drivers/net/dsa/mv88e6xxx/chip.c: In function ‘mv88e6xxx_probe’:
drivers/net/dsa/mv88e6xxx/chip.c:4420:13: warning: ‘compat_info’ may be used uninitialized in this function [-Wmaybe-uninitialized]
chip->info = compat_info;
Actually, it should have warned on the "if (!compat_info)" test, but
whatever.
Explicitly initialize to NULL in the variable declaration to
deal with this.
Fixes: 877b7cb0b6 ("net: dsa: mv88e6xxx: Add minimal platform_data support")
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the size of the EEPROM to the platform data, so it can also be
instantiated by a platform device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all the world uses device tree. Some parts of the world still use
platform devices and platform data. Add basic support for probing a
Marvell switch via platform data.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An IRQ domain will work without an OF node. It is not possible to
reference interrupts via a phandle, but C code can still use
irq_find_mapping() to get an interrupt from the domain.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was possible to delete only one half of an IPv6, which would leave
the second half still programmed and possibly in use. Instead of
checking for the unused bitmap, we need to check the unique bitmap, and
refuse any deletion that does not match that criteria. We also need to
move that check from bcm_sf2_cfp_rule_del_one() into its caller:
bcm_sf2_cfp_rule_del() otherwise we would not be able to delete second
halves anymore that would not pass the first test.
Fixes: ba0696c22e ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had several issues that would make the programming of IPv6 rules both
inconsistent and error prone:
- the chain ID that we would be asking the hardware to put in the
packet's Broadcom tag would be off by one, it would return one of the
two indexes, but not the one user-space specified
- when an user specified a particular location to insert a CFP rule at,
we would not be returning the same index, which would be confusing if
nothing else
- finally, like IPv4, it would be possible to overflow the last entry by
re-programming it
Fix this by swapping the usage of rule_index[0] and rule_index[1] where
relevant in order to return a consistent and correct user-space
experience.
Fixes: ba0696c22e ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we let the kernel pick up a rule location with RX_CLS_LOC_ANY, we
would be able to overwrite the last rules because of a number of issues.
The IPv4 code path would not be checking that rule_index is within
bounds, and it would also only be allowed to pick up rules from range
0..126 instead of the full 0..127 range. This would lead us to allow
overwriting the last rule when we let the kernel pick-up the location.
Fixes: 3306145866 ("net: dsa: bcm_sf2: Move IPv4 CFP processing to specific functions")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the Global 1 specific setup function only setup the statistics
unit, kill it in favor of a mv88e6xxx_stats_setup function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell switch families except 88E6390 have direct registers in
Global 1 for IEEE and IP priorities override mapping. The 88E6390 uses
indirect tables instead.
Add .ieee_pri_map and .ip_pri_map ops to distinct that and call them
from a mv88e6xxx_pri_setup helper. Only non-6390 are concerned ATM.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6390 model has its histogram mode bits moved in the
Global 1 Control 2 register. Use the previously introduced
mv88e6xxx_g1_ctl2_mask helper to set them.
At the same time complete the documentation of the said register.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted the bcm_sf2 driver to implement PHYLINK MAC
operations, we can remove the PHYLIB callbacks: adjust_link() and
fixed_link_update() which are no longer called by DSA.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
