The branch contains driver changes that are tightly
connected to SoC specific code. Aside from smaller
cleanups and bug fixes, here is a list of the notable
changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver
for its on-board pluggable extension bus. The
same platform also gains a firmware driver.
- The Samsung Exynos family gains a new Chipid driver
exporting using the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon
chips.
- A firmware driver for the NXP i.MX DSP IPC protocol
using shared memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the
NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for
the S905X3 and A311D chips
- A rework of the TI Davinci framebuffer driver to
allow important cleanups in the platform code
- A couple of device drivers for removed ARM SoC
platforms are removed. Most of the removals were
picked up by other maintainers, this contains
whatever was left.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=lxFi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This contains driver changes that are tightly connected to SoC
specific code. Aside from smaller cleanups and bug fixes, here is a
list of the notable changes.
New device drivers:
- The Turris Mox router has a new "moxtet" bus driver for its
on-board pluggable extension bus. The same platform also gains a
firmware driver.
- The Samsung Exynos family gains a new Chipid driver exporting using
the soc device sysfs interface
- A similar socinfo driver for Qualcomm Snapdragon chips.
- A firmware driver for the NXP i.MX DSP IPC protocol using shared
memory and a mailbox
Other changes:
- The i.MX reset controller driver now supports the NXP i.MX8MM chip
- Amlogic SoC specific drivers gain support for the S905X3 and A311D
chips
- A rework of the TI Davinci framebuffer driver to allow important
cleanups in the platform code
- A couple of device drivers for removed ARM SoC platforms are
removed. Most of the removals were picked up by other maintainers,
this contains whatever was left"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (123 commits)
bus: uniphier-system-bus: use devm_platform_ioremap_resource()
soc: ti: ti_sci_pm_domains: Add support for exclusive and shared access
dt-bindings: ti_sci_pm_domains: Add support for exclusive and shared access
firmware: ti_sci: Allow for device shared and exclusive requests
bus: imx-weim: remove incorrect __init annotations
fbdev: remove w90x900/nuc900 platform drivers
spi: remove w90x900 driver
net: remove w90p910-ether driver
net: remove ks8695 driver
firmware: turris-mox-rwtm: Add sysfs documentation
firmware: Add Turris Mox rWTM firmware driver
dt-bindings: firmware: Document cznic,turris-mox-rwtm binding
bus: moxtet: fix unsigned comparison to less than zero
bus: moxtet: remove set but not used variable 'dummy'
ARM: scoop: Use the right include
dt-bindings: power: add Amlogic Everything-Else power domains bindings
soc: amlogic: Add support for Everything-Else power domains controller
fbdev: da8xx: use resource management for dma
fbdev: da8xx-fb: drop a redundant if
fbdev: da8xx-fb: use devm_platform_ioremap_resource()
...
The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody is
using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still in
active use and are converted to the ARCH_MULTIPLATFORM build, meaning
that we can compile a kernel that works on these along with most other
ARMv5 platforms. Changes toward that goal are also merged for IOP32x,
but additional work is needed to complete this. Patches for the
remaining ARMv5 platforms have started but need more work and some
testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform
and the move of the TI Davinci platform to a new clocksource driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=u+ew
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Arnd Bergmann:
"The main change this time around is a cleanup of some of the oldest
platforms based on the XScale and ARM9 CPU cores, which are between 10
and 20 years old.
The Kendin/Micrel/Microchip KS8695, Winbond/Nuvoton W90x900 and Intel
IOP33x/IOP13xx platforms are removed after we determined that nobody
is using them any more.
The TI Davinci and NXP LPC32xx platforms on the other hand are still
in active use and are converted to the ARCH_MULTIPLATFORM build,
meaning that we can compile a kernel that works on these along with
most other ARMv5 platforms. Changes toward that goal are also merged
for IOP32x, but additional work is needed to complete this. Patches
for the remaining ARMv5 platforms have started but need more work and
some testing.
Support for the new ASpeed AST2600 gets added, this is based on the
Cortex-A7 ARMv7 core, and is a newer version of the existing ARMv5 and
ARMv6 chips in the same family.
Other changes include a cleanup of the ST-Ericsson ux500 platform and
the move of the TI Davinci platform to a new clocksource driver"
[ The changes had marked INTEL_IOP_ADMA and USB_LPC32XX as being
buildable on other platforms through COMPILE_TEST, but that causes new
warnings that I most definitely do not want to see during the merge
window as that could hide other issues.
So the COMPILE_TEST option got disabled for them again - Linus ]
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (61 commits)
ARM: multi_v5_defconfig: make DaVinci part of the ARM v5 multiplatform build
ARM: davinci: support multiplatform build for ARM v5
arm64: exynos: Enable exynos-chipid driver
ARM: OMAP2+: Delete an unnecessary kfree() call in omap_hsmmc_pdata_init()
ARM: OMAP2+: move platform-specific asm-offset.h to arch/arm/mach-omap2
ARM: davinci: dm646x: Fix a typo in the comment
ARM: davinci: dm646x: switch to using the clocksource driver
ARM: davinci: dm644x: switch to using the clocksource driver
ARM: aspeed: Enable SMP boot
ARM: aspeed: Add ASPEED AST2600 architecture
ARM: aspeed: Select timer in each SoC
dt-bindings: arm: cpus: Add ASPEED SMP
ARM: imx: stop adjusting ar8031 phy tx delay
mailmap: map old company name to new one @microchip.com
MAINTAINERS: at91: remove the TC entry
MAINTAINERS: at91: Collect all pinctrl/gpio drivers in same entry
ARM: at91: move platform-specific asm-offset.h to arch/arm/mach-at91
MAINTAINERS: Extend patterns for Samsung SoC, Security Subsystem and clock drivers
ARM: s3c64xx: squash samsung_usb_phy.h into setup-usb-phy.c
ARM: debug-ll: Add support for r7s9210
...
Pull networking fixes from David Miller:
1) Don't corrupt xfrm_interface parms before validation, from Nicolas
Dichtel.
2) Revert use of usb-wakeup in btusb, from Mario Limonciello.
3) Block ipv6 packets in bridge netfilter if ipv6 is disabled, from
Leonardo Bras.
4) IPS_OFFLOAD not honored in ctnetlink, from Pablo Neira Ayuso.
5) Missing ULP check in sock_map, from John Fastabend.
6) Fix receive statistic handling in forcedeth, from Zhu Yanjun.
7) Fix length of SKB allocated in 6pack driver, from Christophe
JAILLET.
8) ip6_route_info_create() returns an error pointer, not NULL. From
Maciej Żenczykowski.
9) Only add RDS sock to the hashes after rs_transport is set, from
Ka-Cheong Poon.
10) Don't double clean TX descriptors in ixgbe, from Ilya Maximets.
11) Presence of transmit IPSEC offload in an SKB is not tested for
correctly in ixgbe and ixgbevf. From Steffen Klassert and Jeff
Kirsher.
12) Need rcu_barrier() when register_netdevice() takes one of the
notifier based failure paths, from Subash Abhinov Kasiviswanathan.
13) Fix leak in sctp_do_bind(), from Mao Wenan.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (72 commits)
cdc_ether: fix rndis support for Mediatek based smartphones
sctp: destroy bucket if failed to bind addr
sctp: remove redundant assignment when call sctp_get_port_local
sctp: change return type of sctp_get_port_local
ixgbevf: Fix secpath usage for IPsec Tx offload
sctp: Fix the link time qualifier of 'sctp_ctrlsock_exit()'
ixgbe: Fix secpath usage for IPsec TX offload.
net: qrtr: fix memort leak in qrtr_tun_write_iter
net: Fix null de-reference of device refcount
ipv6: Fix the link time qualifier of 'ping_v6_proc_exit_net()'
tun: fix use-after-free when register netdev failed
tcp: fix tcp_ecn_withdraw_cwr() to clear TCP_ECN_QUEUE_CWR
ixgbe: fix double clean of Tx descriptors with xdp
ixgbe: Prevent u8 wrapping of ITR value to something less than 10us
mlx4: fix spelling mistake "veify" -> "verify"
net: hns3: fix spelling mistake "undeflow" -> "underflow"
net: lmc: fix spelling mistake "runnin" -> "running"
NFC: st95hf: fix spelling mistake "receieve" -> "receive"
net/rds: An rds_sock is added too early to the hash table
mac80211: Do not send Layer 2 Update frame before authorization
...
A Mediatek based smartphone owner reports problems with USB
tethering in Linux. The verbose USB listing shows a rndis_host
interface pair (e0/01/03 + 10/00/00), but the driver fails to
bind with
[ 355.960428] usb 1-4: bad CDC descriptors
The problem is a failsafe test intended to filter out ACM serial
functions using the same 02/02/ff class/subclass/protocol as RNDIS.
The serial functions are recognized by their non-zero bmCapabilities.
No RNDIS function with non-zero bmCapabilities were known at the time
this failsafe was added. But it turns out that some Wireless class
RNDIS functions are using the bmCapabilities field. These functions
are uniquely identified as RNDIS by their class/subclass/protocol, so
the failing test can safely be disabled. The same applies to the two
types of Misc class RNDIS functions.
Applying the failsafe to Communication class functions only retains
the original functionality, and fixes the problem for the Mediatek based
smartphone.
Tow examples of CDC functional descriptors with non-zero bmCapabilities
from Wireless class RNDIS functions are:
0e8d:000a Mediatek Crosscall Spider X5 3G Phone
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x0f
connection notifications
sends break
line coding and serial state
get/set/clear comm features
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
and
19d2:1023 ZTE K4201-z
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
CDC Union:
bMasterInterface 0
bSlaveInterface 1
The Mediatek example is believed to apply to most smartphones with
Mediatek firmware. The ZTE example is most likely also part of a larger
family of devices/firmwares.
Suggested-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port the same fix for ixgbe to ixgbevf.
The ixgbevf driver currently does IPsec Tx offloading
based on an existing secpath. However, the secpath
can also come from the Rx side, in this case it is
misinterpreted for Tx offload and the packets are
dropped with a "bad sa_idx" error. Fix this by using
the xfrm_offload() function to test for Tx offload.
CC: Shannon Nelson <snelson@pensando.io>
Fixes: 7f68d43067 ("ixgbevf: enable VF IPsec offload operations")
Reported-by: Jonathan Tooker <jonathan@reliablehosting.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ixgbe driver currently does IPsec TX offloading
based on an existing secpath. However, the secpath
can also come from the RX side, in this case it is
misinterpreted for TX offload and the packets are
dropped with a "bad sa_idx" error. Fix this by using
the xfrm_offload() function to test for TX offload.
Fixes: 5925947047 ("ixgbe: process the Tx ipsec offload")
Reported-by: Michael Marley <michael@michaelmarley.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx code doesn't clear the descriptors' status after cleaning.
So, if the budget is larger than number of used elems in a ring, some
descriptors will be accounted twice and xsk_umem_complete_tx will move
prod_tail far beyond the prod_head breaking the completion queue ring.
Fix that by limiting the number of descriptors to clean by the number
of used descriptors in the Tx ring.
'ixgbe_clean_xdp_tx_irq()' function refactored to look more like
'ixgbe_xsk_clean_tx_ring()' since we're allowed to directly use
'next_to_clean' and 'next_to_use' indexes.
CC: stable@vger.kernel.org
Fixes: 8221c5eba8 ("ixgbe: add AF_XDP zero-copy Tx support")
Signed-off-by: Ilya Maximets <i.maximets@samsung.com>
Tested-by: William Tu <u9012063@gmail.com>
Tested-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There were a couple cases where the ITR value generated via the adaptive
ITR scheme could exceed 126. This resulted in the value becoming either 0
or something less than 10. Switching back and forth between a value less
than 10 and a value greater than 10 can cause issues as certain hardware
features such as RSC to not function well when the ITR value has dropped
that low.
CC: stable@vger.kernel.org
Fixes: b4ded8327f ("ixgbe: Update adaptive ITR algorithm")
Reported-by: Gregg Leventhal <gleventhal@janestreet.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is a spelling mistake in a mlx4_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in a .msg literal string. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in the lmc_trace message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sonic_send_packet will be processed in irq or non-irq
context, so it would better use dev_kfree_skb_any
instead of dev_kfree_skb.
Fixes: d9fb9f3842 ("*sonic/natsemi/ns83829: Move the National Semi-conductor drivers")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In i2400m_op_rfkill_sw_toggle cmd buffer should be released along with
skb response.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1c2977c094 ("net/ibmvnic: free reset work of removed device from queue")
adds a } without corresponding { causing build break.
Fixes: 1c2977c094 ("net/ibmvnic: free reset work of removed device from queue")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Reviewed-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flower control message replies are handled in different locations. The truly
high priority replies are handled in the BH (tasklet) context, while the
remaining replies are handled in a predefined Linux work queue. The work
queue handler orders replies into high and low priority groups, and always
start servicing the high priority replies within the received batch first.
Reply Type: Rtnl Lock: Handler:
CMSG_TYPE_PORT_MOD no BH tasklet (mtu)
CMSG_TYPE_TUN_NEIGH no BH tasklet
CMSG_TYPE_FLOW_STATS no BH tasklet
CMSG_TYPE_PORT_REIFY no WQ high
CMSG_TYPE_PORT_MOD yes WQ high (link/mtu)
CMSG_TYPE_MERGE_HINT yes WQ low
CMSG_TYPE_NO_NEIGH no WQ low
CMSG_TYPE_ACTIVE_TUNS no WQ low
CMSG_TYPE_QOS_STATS no WQ low
CMSG_TYPE_LAG_CONFIG no WQ low
A subset of control messages can block waiting for an rtnl lock (from both
work queue priority groups). The rtnl lock is heavily contended for by
external processes such as systemd-udevd, systemd-network and libvirtd,
especially during netdev creation, such as when flower VFs and representors
are instantiated.
Kernel netlink instrumentation shows that external processes (such as
systemd-udevd) often use successive rtnl_trylock() sequences, which can result
in an rtnl_lock() blocked control message to starve for longer periods of time
during rtnl lock contention, i.e. netdev creation.
In the current design a single blocked control message will block the entire
work queue (both priorities), and introduce a latency which is
nondeterministic and dependent on system wide rtnl lock usage.
In some extreme cases, one blocked control message at exactly the wrong time,
just before the maximum number of VFs are instantiated, can block the work
queue for long enough to prevent VF representor REIFY replies from getting
handled in time for the 40ms timeout.
The firmware will deliver the total maximum number of REIFY message replies in
around 300us.
Only REIFY and MTU update messages require replies within a timeout period (of
40ms). The MTU-only updates are already done directly in the BH (tasklet)
handler.
Move the REIFY handler down into the BH (tasklet) in order to resolve timeouts
caused by a blocked work queue waiting on rtnl locks.
Signed-off-by: Fred Lotter <frederik.lotter@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 36f1031c51 ("ibmvnic: Do not process reset during or after
device removal") made the change to exit reset if the driver has been
removed, but does not free reset work items of the adapter from queue.
Ensure all reset work items are freed when breaking out of the loop early.
Fixes: 36f1031c51 ("ibmnvic: Do not process reset during or after device removal”)
Signed-off-by: Juliet Kim <julietk@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regarding to IEEE 802.3-2015 standard section 2
28B.3 Priority resolution - Table 28-3 - Pause resolution
In case of Local device Pause=1 AsymDir=0, Link partner
Pause=1 AsymDir=1, Local device resolution should be enable PAUSE
transmit, disable PAUSE receive.
And in case of Local device Pause=1 AsymDir=1, Link partner
Pause=1 AsymDir=0, Local device resolution should be enable PAUSE
receive, disable PAUSE transmit.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Reported-by: Shaul Ben-Mayor <shaulb@marvell.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We 'allocate' 'count' bytes here. In fact, 'dev_alloc_skb' already add some
extra space for padding, so a bit more is allocated.
However, we use 1 byte for the KISS command, then copy 'count' bytes, so
count+1 bytes.
Explicitly allocate and use 1 more byte to be safe.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fourth set of fixes for 5.3, and hopefully really the last one. Quite
a few CVE fixes this time but at least to my knowledge none of them
have a known exploit.
mt76
* workaround firmware hang by disabling hardware encryption on MT7630E
* disable 5GHz band for MT7630E as it's not working properly
mwifiex
* fix IE parsing to avoid a heap buffer overflow
iwlwifi
* fix for QuZ device initialisation
rt2x00
* another fix for rekeying
* revert a commit causing degradation in rx signal levels
rsi
* fix a double free
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdcRNmAAoJEG4XJFUm622bGicIAINfu1/7FcDXXEcBmA3ySXM+
VwH9+RF/pW+2bzlPDDFD97i9F6E/9cLnJyJBk0ESpXmdBBRuMw5jQnhpcVUAx7+z
q/Xr5YUyqQYR86HK3UISvF2cgZtern/zhArJL4KJIyzYNX6iHxB8ApGGPHntU5vv
3zdIWqGMWcYpD2IGBs1IPQqn0q3LL/LigZ5v4WMoFNgCVmPfGcjaLFdaiwG/xDFU
2sduxv0hT+JqAbqjDBC/LWCeUGN3W55MEmgGZBjTDuZWZGn+obLcvOLbxJWpSM0d
By3j1FpJ4bEDntvlxdobkjFUcQAWSkvDXXS89b2j1uKEDQ0/MFkj+0QA6dx/bmI=
=0uUN
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2019-09-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 5.3
Fourth set of fixes for 5.3, and hopefully really the last one. Quite
a few CVE fixes this time but at least to my knowledge none of them
have a known exploit.
mt76
* workaround firmware hang by disabling hardware encryption on MT7630E
* disable 5GHz band for MT7630E as it's not working properly
mwifiex
* fix IE parsing to avoid a heap buffer overflow
iwlwifi
* fix for QuZ device initialisation
rt2x00
* another fix for rekeying
* revert a commit causing degradation in rx signal levels
rsi
* fix a double free
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing with a background iperf pushing 1Gbit/sec traffic and running
both ifconfig and netstat to collect statistics, some deadlocks occurred.
Ifconfig and netstat will call nv_get_stats64 to get software xmit/recv
statistics. In the commit f5d827aece ("forcedeth: implement
ndo_get_stats64() API"), the normal tx/rx variables is to collect tx/rx
statistics. The fix is to replace normal tx/rx variables with per
cpu 64-bit variable to collect xmit/recv statistics. The per cpu variable
will avoid deadlocks and provide fast efficient statistics updates.
In nv_probe, the per cpu variable is initialized. In nv_remove, this
per cpu variable is freed.
In xmit/recv process, this per cpu variable will be updated.
In nv_get_stats64, this per cpu variable on each cpu is added up. Then
the driver can get xmit/recv packets statistics.
A test runs for several days with this commit, the deadlocks disappear
and the performance is better.
Tested:
- iperf SMP x86_64 ->
Client connecting to 1.1.1.108, TCP port 5001
TCP window size: 85.0 KByte (default)
------------------------------------------------------------
[ 3] local 1.1.1.105 port 38888 connected with 1.1.1.108 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-10.0 sec 1.10 GBytes 943 Mbits/sec
ifconfig results:
enp0s9 Link encap:Ethernet HWaddr 00:21:28:6f:de:0f
inet addr:1.1.1.105 Bcast:0.0.0.0 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5774764531 errors:0 dropped:0 overruns:0 frame:0
TX packets:633534193 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:7646159340904 (7.6 TB) TX bytes:11425340407722 (11.4 TB)
netstat results:
Kernel Interface table
Iface MTU Met RX-OK RX-ERR RX-DRP RX-OVR TX-OK TX-ERR TX-DRP TX-OVR Flg
...
enp0s9 1500 0 5774764531 0 0 0 633534193 0 0 0 BMRU
...
Fixes: f5d827aece ("forcedeth: implement ndo_get_stats64() API")
CC: Joe Jin <joe.jin@oracle.com>
CC: JUNXIAO_BI <junxiao.bi@oracle.com>
Reported-and-tested-by: Nan san <nan.1986san@gmail.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NETDEV_TX_BUSY really should only be used by drivers that call
netif_tx_stop_queue() at the wrong moment. If dma_map_single() is
failed to map tx DMA buffer, it might trigger an infinite loop.
This patch use NETDEV_TX_OK instead of NETDEV_TX_BUSY, and change
printk to pr_err_ratelimited.
Fixes: d9fb9f3842 ("*sonic/natsemi/ns83829: Move the National Semi-conductor drivers")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change lowers ring buffer reclaim threshold from 1/2*queue to budget
for better performance. According to our test with qemu + dpdk, packet
dropping happens when the guest is not able to provide free buffer in
avail ring timely with default 1/2*queue. The value in the patch has been
tested and does show better performance.
Test setup: iperf3 to generate packets to guest (total 30mins, pps 400k, UDP)
avg packets drop before: 2842
avg packets drop after: 360(-87.3%)
Further, current code suffers from a starvation problem: the amount of
work done by try_fill_recv is not bounded by the budget parameter, thus
(with large queues) once in a while userspace gets blocked for a long
time while queue is being refilled. Trigger refills earlier to make sure
the amount of work to do is limited.
Signed-off-by: jiangkidd <jiangkidd@hotmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
`dev` (struct rsi_91x_usbdev *) field of adapter
(struct rsi_91x_usbdev *) is allocated and initialized in
`rsi_init_usb_interface`. If any error is detected in information
read from the device side, `rsi_init_usb_interface` will be
freed. However, in the higher level error handling code in
`rsi_probe`, if error is detected, `rsi_91x_deinit` is called
again, in which `dev` will be freed again, resulting double free.
This patch fixes the double free by removing the free operation on
`dev` in `rsi_init_usb_interface`, because `rsi_91x_deinit` is also
used in `rsi_disconnect`, in that code path, the `dev` field is not
(and thus needs to be) freed.
This bug was found in v4.19, but is also present in the latest version
of kernel. Fixes CVE-2019-15504.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 9ad3b55654.
As reported by Sergey:
"I got some problem after upgrade kernel to 5.2 version (debian testing
linux-image-5.2.0-2-amd64). 5Ghz client stopped to see AP.
Some tests with 1metre distance between client-AP: 2.4Ghz -22dBm, for
5Ghz - 53dBm !, for longer distance (8m + walls) 2.4 - 61dBm, 5Ghz not
visible."
It was identified that rx signal level degradation was caused by
9ad3b55654 ("rt2800: enable TX_PIN_CFG_LNA_PE_ bits per band").
So revert this commit.
Cc: <stable@vger.kernel.org> # v5.1+
Reported-and-tested-by: Sergey Maranchuk <slav0nic0@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After looking at code I realized that my previous fix
9584412438 ("rt2x00: clear IV's on start to fix AP mode regression")
was incomplete. We can still have wrong IV's after re-keyring.
To fix that, clear up IV's also on key removal.
Fixes: 710e6cc159 ("rt2800: do not nullify initialization vector data")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
tested-by: Emil Karlson <jekarl@iki.fi>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We were erroneously assigning the new configuration to a local
variable cfg, but that was not being assigned to anything, so the
change was getting lost. Assign directly to iwl_trans->cfg instead.
Fixes: 5a8c31aa63 ("iwlwifi: pcie: fix recognition of QuZ devices")
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_update_vs_ie(),mwifiex_set_uap_rates() and
mwifiex_set_wmm_params() call memcpy() without checking
the destination size.Since the source is given from
user-space, this may trigger a heap buffer overflow.
Fix them by putting the length check before performing memcpy().
This fix addresses CVE-2019-14814,CVE-2019-14815,CVE-2019-14816.
Signed-off-by: Wen Huang <huangwenabc@gmail.com>
Acked-by: Ganapathi Bhat <gbhat@marvell.comg>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MT7630E hardware does support 5GHz, but we do not properly configure phy
for 5GHz channels. Scanning at this band not only do not show any APs
but also can hang the firmware.
Since vendor reference driver do not support 5GHz we don't know how
properly configure 5GHz channels. So disable this band for MT7630E .
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 41634aa8d6 ("mt76: only schedule txqs from the tx tasklet")
I can observe firmware hangs on MT7630E on station mode: tx stop
functioning after minor activity (rx keep working) and on module
unload device fail to stop with messages:
[ 5446.141413] mt76x0e 0000:06:00.0: TX DMA did not stop
[ 5449.176764] mt76x0e 0000:06:00.0: TX DMA did not stop
Loading module again results in failure to associate with AP.
Only machine power off / power on cycle can make device work again.
It's unclear why commit 41634aa8d6 causes the problem, but it is
related to HW encryption. Since issue is a firmware hang, that is super
hard to debug, just disable HW encryption as fix for the issue.
Fixes: 41634aa8d6 ("mt76: only schedule txqs from the tx tasklet")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In function sun8i_dwmac_set_syscon(), local variable "val" could
be uninitialized if function regmap_field_read() returns -EINVAL.
However, it will be used directly in the if statement, which
is potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 99cd149efe ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.
Fix it now.
Rename the corresponding label to something more in line.
Fixes: 99cd149efe ("sgiseeq: replace use of dma_cache_wback_inv")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call to 'pci_free_irq_vectors()' are missing both in the error handling
path of the probe function, and in the remove function.
Add them.
Fixes: 19971f5ea0 ("enetc: add PTP clock driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change enables the use of SW timestamping on the Raspberry Pi 4.
bcmgenet's transmit function bcmgenet_xmit() implements software
timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE capability was
missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced. By using
ethtool_ops bcmgenet_ethtool_ops() as get_ts_info(), the
SOF_TIMESTAMPING_TX_SOFTWARE capability is announced.
Similar to commit a8f5cb9e79 ("smsc95xx: use ethtool_op_get_ts_info()")
Signed-off-by: Ryan M. Collins <rmc032@bucknell.edu>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a 3-Port 10/100 Ethernet Switch with 1588v2 PTP.
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On embedded environments with hard memory limits it is a normal although
rare case when skb can't be allocated on rx part under high traffic.
In such OOM cases napi_complete_done() was not called.
So the napi object became in an invalid state like it is "scheduled".
Kernel do not re-schedules the poll of that napi object.
Consequently, kernel can not remove that object the system hangs on
`ifconfig down` waiting for a poll.
We are fixing this by gracefully closing napi poll routine with correct
invocation of napi_complete_done.
This was reproduced with artificially failing the allocation of skb to
simulate an "out of memory" error case and check that traffic does
not get stuck.
Fixes: 970a2e9864 ("net: ethernet: aquantia: Vector operations")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declaring threaded irq handler should also indicate the irq is
oneshot. It is oneshot indeed, because HW implements irq automasking
on trigger.
Not declaring this causes some kernel configurations to fail
on interface up, because request_threaded_irq returned an err code.
The issue was originally hidden on normal x86_64 configuration with
latest kernel, because depending on interrupt controller, irq driver
added ONESHOT flag on its own.
Issue was observed on older kernels (4.14) where no such logic exists.
Fixes: 4c83f170b3 ("net: aquantia: link status irq handling")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reported-by: Michael Symolkin <Michael.Symolkin@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of device reconfiguration the driver may reset the device invisible
for other modules, vlan module in particular. So vlans will not be
removed&created and vlan filters will not be configured in the device.
The patch reapplies the vlan filters at device start.
Fixes: 7975d2aff5 ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a limit condition of vlans on the interface before setting vlan
promiscuous mode
Fixes: 48dd73d08d ("net: aquantia: fix vlans not working over bridged network")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to absence of checking against the rx flow rule when vlan 0 is being
removed, the other rule could be removed instead of the rule with vlan 0
Fixes: 7975d2aff5 ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the register value width as the regmap_config name to prevent the
following error when the second and third regmap_configs are
initialized.
"debugfs: Directory '${bus-id}' with parent 'regmap' already present!"
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-08-31
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix 32-bit zero-extension during constant blinding which
has been causing a regression on ppc64, from Naveen.
2) Fix a latency bug in nfp driver when updating stack index
register, from Jiong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The devicetree binding lists the phy phy as optional. As such, the
driver should not bail out if it can't find a regulator. Instead it
should just skip the remaining regulator related code and continue
on normally.
Skip the remainder of phy_power_on() if a regulator supply isn't
available. This also gets rid of the bogus return code.
Fixes: 2e12f53663 ("net: stmmac: dwmac-rk: Use standard devicetree property for phy regulator")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In xgbe_mod_init(), we should do cleanup if some error occurs
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: efbaa82833 ("amd-xgbe: Add support to handle device renaming")
Fixes: 47f164deab ("amd-xgbe: Add PCI device support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to use a different firmware for C0 versions of killer Qu NICs.
Add structures for them and handle them in the if block that detects
C0 revisions.
Additionally, instead of having an inclusive check for QnJ devices,
make the selection exclusive, so that switching to QnJ is the
exception, not the default. This prevents us from having to add all
the non-QnJ cards to an exclusion list. To do so, only go into the
QnJ block if the device has an RF ID type HR and HW revision QnJ.
Cc: stable@vger.kernel.org # 5.2
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/20190821171732.2266-1-luca@coelho.fi
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A similar workaround for the suspend/resume problem is needed for yet
another ASUS machines, P6X models. Like the previous fix, the BIOS
doesn't provide the standard DMI_SYS_* entry, so again DMI_BOARD_*
entries are used instead.
Reported-and-tested-by: SteveM <swm@swm1.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent code changes to NFP allowed the offload of neighbour entries to FW
when the next hop device was an internal port. This allows for offload of
tunnel encap when the end-point IP address is applied to such a port.
Unfortunately, the neighbour event handler still rejects events that are
not associated with a repr dev and so the firmware neighbour table may get
out of sync for internal ports.
Fix this by allowing internal port neighbour events to be correctly
processed.
Fixes: 45756dfeda ("nfp: flower: allow tunnels to output to internal port")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal port TC offload is implemented through user-space applications
(such as OvS) by adding filters at egress via TC clsact qdiscs. Indirect
block offload support in the NFP driver accepts both ingress qdisc binds
and egress binds if the device is an internal port. However, clsact sends
bind notification for both ingress and egress block binds which can lead
to the driver registering multiple callbacks and receiving multiple
notifications of new filters.
Fix this by rejecting ingress block bind callbacks when the port is
internal and only adding filter callbacks for egress binds.
Fixes: 4d12ba4278 ("nfp: flower: allow offloading of matches on 'internal' ports")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
