There are several corner cases where driver might get a 2nd notification
about the same link change. Don't log any additional changes if the
physical carrier is already reported as it should.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a corner-case in HW where an SKB queued for transmission that
contains too many frags will cause FW to assert.
This patch solves this by linearizing the SKB if necessary.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device ID for the 10g module has changed. Populate the pci_ids table
accordingly.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce the use of kobj_to_dev() helper function instead of open
coding it with container_of()
The Coccinelle semantic patch used to make this change is as follows:
//<smpl>
@@
expression a;
symbol kobj;
@@
- container_of(a, struct device, kobj)
+ kobj_to_dev(a)
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW hsi contains regpairs, mostly for 64-bit address representations.
Since same paradigm is applied each time a regpair is filled, this
introduces a new utility macro for setting such regpairs.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each configuration element send via ramrod requires a Slow Path Queue
entry. This slightly changes the way such an entry is configured, but
contains mostly semantic changes [where more parameters are gathered
in a sub-struct instead of being directly passed].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to HW design, some of the memories are wide-bus and access to those
needs to be sequentialized on a per-HW-block level; Read/write to a
given HW-block might break other read/write to wide-bus memory done at
~same time.
Status blocks initialization in CAU is done into such a wide-bus memory.
This moves the initialization into using DMAE which is guaranteed to be
safe to use on such memories.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial driver submission used GFP_ATOMIC almost inclusively when
allocating memory. We now remedy this point, using GFP_KERNEL where
it's possible.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device would start receiving only vlan-tagged traffic with tags matching
that of one of the configured vlan IDs, unless:
- Device is expliicly placed in PROMISC mode.
- Device exhausts its vlan filter credits.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Today, interfaces are working in vlan-promisc mode; But once
vlan filtering offloaded would be supported, we'll need a method to
control it directly [e.g., when setting device to PROMISC, or when
running out of vlan credits].
This adds the necessary API for L2 client to manually choose whether to
accept all vlans or only those for which filters were configured.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the qed* driver into utilizing the 8.7.3.0 FW.
This new FW is required for a lot of new SW features, including:
- Vlan filtering offload
- Encapsulation offload support
- HW ingress aggregations
As well as paving the way for the possibility of adding storage protocols
in the future.
V2:
- Fix kbuild test robot error/warnings.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since qlcnic_alloc_mbx_args can be failed,
return value should be checked.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qlcnic_dcb_ops structures are never modified, so declare them as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code, if we succeeded on the last iteration through the
loop then we still returned failure.
Fixes: 389e4e04ad ('qlcnic: fix a timeout loop')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem here is that at the end of the loop we test for if
idc->vnic_wait_limit is zero, but since idc->vnic_wait_limit-- is a
post-op, it actually ends up set to (u8)-1. I have fixed this by
moving the decrement inside the loop.
Fixes: 486a5bc77a ('qlcnic: Add support for 83xx suspend and resume.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The problem here is that after the loop we test for "if (!i) " but
because "i--" is a post-op we exit with i set to -1. I have fixed this
by changing it to a pre-op instead. I had to change the starting value
from 3 to 4 so that we still iterate 3 times.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using INTa, ISR might be called before device is configured
for INTa [E.g., due to other device asserting the shared interrupt line],
in which case the ISR would read the SISR registers that shouldn't be
read unless HW is already configured for INTa. This might break interrupts
later on. There's also an MSI-X issue due to this difference, although
it's mostly theoretical.
This patch changes the initialization order, calling request_irq() for the
slowpath interrupt only after the chip is configured for working
in the preferred interrupt mode.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Can't rely on pci config space to discover bar size,
as in some environments this returns a wrong, too large value.
Instead, rely on device register, which contains the value
provided by MFW at preboot.
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Concurrent non-blocking slowpath ramrods can be completed
out-of-order on the completion chain. Recycling completed elements,
while previously sent elements are still completion pending,
can lead to overriding of active elements on the chain. Furthermore,
sending pending slowpath ramrods currently lacks the update of the
chain element physical pointer.
This patch:
* Ensures that ramrods are sent to the FW with
consecutive echo values.
* Handles out-of-order completions by freeing only first
successive completed entries.
* Updates the chain element physical pointer when copying
a pending element into a free element for sending.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical LEDs are being controlled by the management FW.
This adds the qed functionality required to request management FW to
change the LED configuration, as well as the necessary APIs for this
functionality to later be used by the protocol drivers.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_napi_add() is a variant of netif_napi_add()
It should be used by drivers that use a napi structure
to exclusively poll TX.
We do not want to add this kind of napi in napi_hash[] in following
patches, adding generic busy polling to all NAPI drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added qlogic qed driver uses the zlib library, but
misses the dependency:
drivers/built-in.o: In function `qed_alloc_stream_mem':
drivers/net/ethernet/qlogic/qed/qed_main.c:707: undefined reference to `zlib_inflate_workspacesize'
drivers/built-in.o: In function `qed_unzip_data':
drivers/net/ethernet/qlogic/qed/qed_main.c:675: undefined reference to `zlib_inflateInit2'
This changes Kconfig to always select zlib when needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: David S. Miller <davem@davemloft.net>
The bonding driver saves a copy of slaves' original mac address and then
assigns whatever mac as needed to the slave, depending on mode. In at
least modes 5 and 6 (balance-tlb, balance-alb), it often ends up being the
mac address of another slave. On release from the bond, the original mac
address is supposed to get restored via a dev_set_mac_address() call in
the bonding driver's __bond_release_one() function, which calls the
slave's ndo_set_mac_address function, which for qlcnic, is
qlcnic_set_mac().
Now, this function tries to be somewhat intelligent and exit early if
you're trying to set the mac address to the same thing that is already
set. The problem here is that adapter->mac_addr isn't in sync with
netdev->dev_addr. The qlcnic driver still has the original mac stored in
adapter->mac_addr, while the bonding driver has updated netdev->dev_addr,
so qlcnic thinks we're trying to set the same address it already has.
I think the way to go here, since the function updates both netdev and
adapter's stored mac addresses, is to check if either of them doesn't
match the newly requested mac. Simply checking netdev's value only could
result in a similar mismatch and non-update, so look at both.
CC: Dept-GELinuxNICDev@qlogic.com
CC: netdev@vger.kernel.org
CC: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally return success instead of -ENOMEM here.
Fixes: fe56b9e6a8 ('qed: Add module with basic common support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com
Signed-off-by: David S. Miller <davem@davemloft.net>
MODE_MF_SI is 9. We should be testing bit 9 instead of AND 0x9.
Fixes: fe56b9e6a8 ('qed: Add module with basic common support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We check if "p_hwfn" is NULL and then dereference it in the error
handling code. I read the code and it isn't NULL so let's remove the
check.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic ethtool operations to the qed driver, allowing support in:
- Statistics gathering [ethtool -S]
- Setting of debug level [ethtool -s <interface> msglvl]
- Getting basic information [ethtool, ethtool -i]
In addition it adds the ability to change the MTU.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Device statistics can be gathered on-demand. This adds the qed support for
reading the statistics [both function and port] from the device, and adds
to the public API a method for requesting the current statistics.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds basic link functionality to qede - driver still doesn't provide
users with an API to change any link property, but it does request qed to
initialize the link using default configuration, and registers a callback
that allows it to get link notifications.
This patch adds the ability of the driver to set the carrier as active and
to enable traffic as a result of async. link notifications.
Following this patch, driver should be capable of running traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Physical link is handled by the management Firmware.
This patch lays the infrastructure for attention handling in the driver,
as link change notifications arrive via async. attentions,
as well the handling of such notifications.
This patch also extends the API with the protocol drivers by adding
registered callbacks which the protocol driver passes to qed in order
to be notified of async. events originating from the FW/HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to configure basic classification in driver by
implementing ndo_set_mac_address() and ndo_set_rx_mode().
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch includes the basic Rx/Tx support for the driver [although
carrier will still never be turned on].
Following this patch the driver registers a network device, initializes
it and prepares it for traffic.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds to the qed the support to configure various L2 elements,
such as channels and basic filtering conditions.
It also enhances its public API to allow qede to later utilize this
functionality.
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver for Ethernet is the Ethernet specific module for
QL4xxx ethernet products by Qlogic.
This patch adds a very minimal PCI driver, one that doesn't yet register
a network device, but one that does interact with qed and does a basic
initialization of the HW.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a public API for a network driver to work on top of QED.
The interface itself is very minimal - it's mostly infrastructure, as the
only content it has after this patch is a query for HW-based information
required for the creation of a network interface [I.e., no actual
protocol-specific configurations are supported].
Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Qlogic Everest Driver is the backend module for the QL4xxx ethernet
products by Qlogic.
This module serves two main purposes:
1. It's responsible to contain all the common code that will be shared
between the various drivers that would be used with said line of
products. Flows such as chip initialization and de-initialization
fall under this category.
2. It would abstract the protocol-specific HW & FW components, allowing
the protocol drivers to have a clean APIs which is detached in its
slowpath configuration from the actual HSI.
This adds a very basic module without any protocol-specific bits.
I.e., this adds a basic implementation that almost entirely falls under
the first category.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only instance of a qlcnic_mbx_ops structure is never modified. Thus
the declaration of the structure and all references to the structure type
can be made const.
In the definition of the qlcnic_mailbox structure, the ops field is no
longer lined up with the other fields. This was left as is, to avoid a lot
of trivial changes on the other lines.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback for adding vxlan port can be called with the same port for
both IPv4 and IPv6. Do not disable the offloading when the same port for
both protocols is added and later one of them removed.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all cases, mbx->req.arg and mbx->rsp.arg have just been allocated
using kcalloc(), so these six memsets are redundant.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver allocates a large chunk of temporary buffer using kzalloc
to copy FW image. As there is no real need of this memory to be
physically contiguous, use vzalloc instead.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases it is required to capture minidump for iSCSI functions
as part of default minidump collection process. To enable this, firmware
exports it's capability and driver need to enable that capability
by issuing a mailbox command.
With this feature, firmware can provide additional iSCSI function's
minidump with smaller minidump capture mask (0x1f).
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include local headers files after kernel's header files.
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use proper typecasting while performing byte-by-byte copy
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to memset memory allocated with vzalloc.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/amd-xgbe-phy.c
drivers/net/wireless/iwlwifi/Kconfig
include/net/mac80211.h
iwlwifi/Kconfig and mac80211.h were both trivial overlapping
changes.
The drivers/net/phy/amd-xgbe-phy.c file got removed in 'net-next' and
the bug fix that happened on the 'net' side is already integrated
into the rest of the amd-xgbe driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace confusing QL_STATUS_INVALID_PARAM == -1 == -EPERM with -EINVAL
and QLC_STATUS_UNSUPPORTED_CMD == -2 == -ENOENT with -EOPNOTSUPP, the
latter error code is arguable, but it is already used in the driver,
so let it be here as well.
Also remove always false (!buf) check on read(), the driver should
not care if userspace gets its EFAULT or not.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If read() syscall requests unexpected number of bytes from "dimm" binary
attribute file, return EINVAL instead of EPERM.
At the same time pin down sysfs file size to the fixed
sizeof(struct netxen_dimm_cfg), which allows to exploit some missing
sanity checks from kernfs (file boundary checks vs offset etc.)
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
30 usecs (or really, 1 jiffy) can go by pretty fast.
Move the set of the timeout immediately before the loop.
Remove the unnecessary max(1ul, usecs_to_jiffies(30)) as
usecs_to_jiffies with a non-zero constant is guaranteed
to be non-zero.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch should have been part of the previous patch having the
same summary. See http://marc.info/?l=linux-kernel&m=143039470103795&w=2
Unfortunately, I didn't check to see where else this lock was used before
submitting that patch. This should take care of it for netxen_nic, as I
did a thorough search this time.
To recap from the original patch; although testing this driver with
DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled did not produce any traces,
it would be more prudent in the case of tx_clean_lock to use _bh
versions of spin_[un]lock, since this lock is manipulated in both
the process and softirq contexts.
This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Acked-By: Neil Horman <nhorman@tuxdriver.com>
Acked-By: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing this driver with DEBUG_LOCKDEP and DEBUG_SPINLOCK
enabled did not produce any traces, it would be more prudent in the
case of tx_clean_lock to use spin_[un]lock_bh, since this lock is
manipulated in both the process and softirq contexts.
This patch was tested for functionality and regressions with netperf
and DEBUG_LOCKDEP and DEBUG_SPINLOCK enabled.
Signed-off-by: Tony Camuso <tcamuso@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
To allow drivers to handle the features check for multiple tags,
move the check to ndo_features_check().
As no drivers currently handle multiple tagged TSO, introduce
dflt_features_check() and call it if the driver does not have
ndo_features_check().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change 'mutliple' to 'multiple'
Change 'Firmare' to 'Firmware'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver keeps adding multicast addresses without deleting removed MACs and
worrying about adapters filter limit. This results into actual count of programmed
multicast addresses get accumulated over the time and overruns the adapter's
filter limit without putting device in ACCEPT_ALL_MULTI mode. This causes
newly added multicast traffic to fail after the sequence of addition - deletion
in certain pattern.
This issue is seen only when netdev's mcast list count is less than adapters
mcast filter limit.
e.g. If adapters multicast filter limit is 38 per function
then following sequence would result in multicast traffic failure for
newly added MACs.
- add less than 38 multicast MACs
- remove previously added multicast MACs
- add new multicast MACs (less than 38)
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions kfree() and vfree() perform also input parameter validation.
Thus the test around their calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
After d75b1ade56 ("net: less interrupt masking in NAPI")
driver's NAPI poll routine is expected to return
exact budget value if it wants to be re-called.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Fixes: d75b1ade56 ("net: less interrupt masking in NAPI")
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently qlge_update_hw_vlan_features() will always first put the
interface down, then update features and then bring it up again. But it
is possible to hit this code while the adapter is down and this causes a
non-paired call to napi_disable(), which will get stuck.
This patch fixes it by skipping these down/up actions if the interface
is already down.
Fixes: a45adbe8d3 ("qlge: Enhance nested VLAN (Q-in-Q) handling.")
Cc: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
NAPI poll logic now enforces that a poller returns exactly the budget
when it wants to be called again.
If a driver limits TX completion, it has to return budget as well when
the limit is hit, not the number of received packets.
Reported-and-tested-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: d75b1ade56 ("net: less interrupt masking in NAPI")
Cc: Manish Chopra <manish.chopra@qlogic.com>
Acked-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The counter variable wasn't increased at all which may stuck under
certain circumstances.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use normal facilities to avoid printing each byte
on a separate line.
Now emits at KERN_DEBUG instead of KERN_INFO.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the check of adapter fails and goes into the 'else' branch, the
return value 'err' should not still be zero.
Signed-off-by: Yongjian Xu <xuyongjiande@gmail.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GSO isn't the only offload feature with restrictions that
potentially can't be expressed with the current features mechanism.
Checksum is another although it's a general issue that could in
theory apply to anything. Even if it may be possible to
implement these restrictions in other ways, it can result in
duplicate code or inefficient per-packet behavior.
This generalizes ndo_gso_check so that drivers can remove any
features that don't make sense for a given packet, similar to
netif_skb_features(). It also converts existing driver
restrictions to the new format, completing the work that was
done to support tunnel protocols since the issues apply to
checksums as well.
By actually removing features from the set that are used to do
offloading, it solves another problem with the existing
interface. In these cases, GSO would run with the original set
of features and not do anything because it appears that
segmentation is not required.
CC: Tom Herbert <therbert@google.com>
CC: Joe Stringer <joestringer@nicira.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Tom Herbert <therbert@google.com>
Fixes: 04ffcb255f ("net: Add ndo_gso_check")
Tested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So this can be reused for identification of other "items" as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use vxlan_gso_check() to advertise offload support for this NIC.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Poll for the link events only if firmware doesn't have capability
to notify the driver for the link events.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Number of arguments taken by destroy tx command is three
instead of two.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Initially we were programming maximum number of arguments.
Instead we should program number of arguments required in
a command.
o Maximum number of arguments for 82xx adapter is four. Fix it
for GET_ESWITCH_STATS command.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver is not updating sw_consumer while processing Tx completion
when interface is going down. Due to this interface down path gets
stuck forever waiting for NAPI to complete.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o __netxen_nic_down() function might sleep while holding spinlock_t(tx_clean_lock).
Acquire this lock for only releasing TX buffers instead of taking it
for whole down path.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o When TX queues are not allocated, driver does not fill TX queues stats in the buffer.
However, it is also not advancing data pointer by TX queue stats length, which would
misplace all successive stats data in the buffer and will result in mismatch between
stats strings and it's values.
o Fix this by advancing data pointer by TX queue stats length when
queues are not allocated.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o TX queues stats must be read when queues are allocated regardless
of interface is up or not.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver is doing memset with zero for total number of stats bytes when
it has already filled some data in the stats buffer, which can overwrite
memory area beyond the length of stats buffer.
o Fix this by initializing stats buffer with zero before filling any data in it.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In qlcnic_83xx_setup_idc_parameters() routine use qlcnic_83xx_flash_read32() API
which takes flash lock internally instead of the lockless version
qlcnic_83xx_lockless_flash_read32().
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the below warning message:
qlge_main.c:1754: warning: 'lbq_desc' may be used uninitialized in this function
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set skb->csum_level instead of skb->encapsulation when indicating
CHECKSUM_UNNECESSARY for an encapsulated checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to run Power On Self Test (POST) for 83xx adapters.
POST can be run in 3 different speed modes :
i) Fast mode (takes about 690 ms)
ii) Medium mode (takes about 2930 ms)
iii) Slow mode (takes about 7500 ms)
To run POST, firmware file with name "83xx_post_fw.bin" should be present under
/lib/firmware directory. load_fw_file module parameter is used to specify
POST operation and its speed mode.
load_fw_file = 2 : Fast mode
load_fw_file = 3 : Medium mode
load_fw_file = 4 : Slow mode
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per recommendation, msleep() may sleep longer than intended time for
values less than 20ms. So, use usleep_range() instead of msleep()
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Update the port type information
o Advertise correct link modes and autonegotiation
o Add support to change link speed
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix spelling typo in printk within vairous
part of the code.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This device claims TSO support for vlans. It also allows a user to
control vlan acceleration offloading. As such, it is possible to turn
off vlan acceleration and configure a vlan which will continue to send
TSO traffic.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information.
This results in corrupted frames sent on the wire.
This patch extracts the protocol value correctly by using a
vlan_get_protocol() helper and corrects corrupt TSO frames.
CC: Shahed Shaikh <shahed.shaikh@qlogic.com>
CC: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
CC: Ron Mercer <ron.mercer@qlogic.com>
CC: linux-driver@qlogic.com
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware binary file is in little endian. On big-endian architecture, while
writing this binary FW file to adapters memory, writel() swaps the data resulting into
corruption of FW image. So, swap the data before writing into adapters memory.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware dump template header is read from adapter using
readl() which swaps the data. So, adjust structure
element on the boundary of 32bit dword.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Application expects flash data in little endian, but driver reads/writes
flash data using readl()/writel() APIs which swaps data on big endian machine.
So, swap the data after reading from and before writing to flash memory.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Miscellaneous
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=jJGu
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull DEFINE_PCI_DEVICE_TABLE removal from Bjorn Helgaas:
"Part two of the PCI changes for v3.17:
- Remove DEFINE_PCI_DEVICE_TABLE macro use (Benoit Taine)
It's a mechanical change that removes uses of the
DEFINE_PCI_DEVICE_TABLE macro. I waited until later in the merge
window to reduce conflicts, but it's possible you'll still see a few"
* tag 'pci-v3.17-changes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Remove DEFINE_PCI_DEVICE_TABLE macro use
Pull networking fixes from David Miller:
"Several networking final fixes and tidies for the merge window:
1) Changes during the merge window unintentionally took away the
ability to build bluetooth modular, fix from Geert Uytterhoeven.
2) Several phy_node reference count bug fixes from Uwe Kleine-König.
3) Fix ucc_geth build failures, also from Uwe Kleine-König.
4) Fix klog false positivies when netlink messages go to network
taps, by properly resetting the network header. Fix from Daniel
Borkmann.
5) Sizing estimate of VF netlink messages is too small, from Jiri
Benc.
6) New APM X-Gene SoC ethernet driver, from Iyappan Subramanian.
7) VLAN untagging is erroneously dependent upon whether the VLAN
module is loaded or not, but there are generic dependencies that
matter wrt what can be expected as the SKB enters the stack.
Make the basic untagging generic code, and do it unconditionally.
From Vlad Yasevich.
8) xen-netfront only has so many slots in it's transmit queue so
linearize packets that have too many frags. From Zoltan Kiss.
9) Fix suspend/resume PHY handling in bcmgenet driver, from Florian
Fainelli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (55 commits)
net: bcmgenet: correctly resume adapter from Wake-on-LAN
net: bcmgenet: update UMAC_CMD only when link is detected
net: bcmgenet: correctly suspend and resume PHY device
net: bcmgenet: request and enable main clock earlier
net: ethernet: myricom: myri10ge: myri10ge.c: Cleaning up missing null-terminate after strncpy call
xen-netfront: Fix handling packets on compound pages with skb_linearize
net: fec: Support phys probed from devicetree and fixed-link
smsc: replace WARN_ON() with WARN_ON_SMP()
xen-netback: Don't deschedule NAPI when carrier off
net: ethernet: qlogic: qlcnic: Remove duplicate object file from Makefile
wan: wanxl: Remove typedefs from struct names
m68k/atari: EtherNEC - ethernet support (ne)
net: ethernet: ti: cpmac.c: Cleaning up missing null-terminate after strncpy call
hdlc: Remove typedefs from struct names
airo_cs: Remove typedef local_info_t
atmel: Remove typedef atmel_priv_ioctl
com20020_cs: Remove typedef com20020_dev_t
ethernet: amd: Remove typedef local_info_t
net: Always untag vlan-tagged traffic on input.
drivers: net: Add APM X-Gene SoC ethernet driver support.
...
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
In the Makefile, qlcnic_minidump.o is included twice in the list of
object files linked into qlcnic.o.
This change removes the superfluous include.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/Makefile
net/ipv6/sysctl_net_ipv6.c
Two ipv6_table_template[] additions overlap, so the index
of the ipv6_table[x] assignments needed to be adjusted.
In the drivers/net/Makefile case, we've gotten rid of the
garbage whereby we had to list every single USB networking
driver in the top-level Makefile, there is just one
"USB_NETWORKING" that guards everything.
Signed-off-by: David S. Miller <davem@davemloft.net>
o Initialization of dcbnl_ops after register netdev may result in
dcbnl_ops not getting set before it is being accessed from open.
So, moving it before register_netdev.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Earlier, set_drv_version was getting called after register_netdev.
This was resulting in a race between set_drv_version and FLR called
from open(). Moving set_drv_version before register_netdev avoids
the race.
o Log response code in error message on CDRP failure.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Aggregating tx stats in adapter variable was resulting in
an increase in stats even after no traffic was run and
user runs ifconfig/ethtool command.
o qlcnic_update_stats used to accumulate stats in adapter
struct at each function call, instead accumulate tx stats
in local variable and then assign it to adapter structure.
Reported-by: Holger Kiehl <holger.kiehl@dwd.de>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: fixed issue with checking return of dcbnl_rtnl_ops->getapp()
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumping a bridge fdb dumps every fdb entry
held. With this change we are going to filter
on selected bridge port.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Collect a firmware dump on first Tx timeout if netif_msg_tx_err() is set
- Log Receive and Status ring info on Tx timeout, in addition to Tx ring info
- Log additional Tx ring info if netif_msg_tx_err() is set
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Check interrupt mode at the start of qlcnic_set_channels().
- Do not validate ring count if they are not going to change.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pre-allocate the physically contiguous DMA buffer used for
minidump collection at driver load time, rather than at
run time, to minimize allocation failures. Driver will allocate
the buffer at load time if PEX DMA support capability is indicated
by the adapter.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QLC_83XX_GET_LSO_CAPABILITY define is cut and pasted twice so we can
delete the second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netback/netback.c
net/core/filter.c
A filter bug fix overlapped some cleanups and a conversion
over to some new insn generation macros.
A xen-netback bug fix overlapped the addition of multi-queue
support.
Signed-off-by: David S. Miller <davem@davemloft.net>
o Uninitialzed fields in mailbox command structure
caused commands to time out randomly due to garbage
values so initialize it to zero.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/net/inetpeer.h
net/ipv6/output_core.c
Changes in net were fixing bugs in code removed in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is called from dcbnl_build_peer_app(). The "info"
struct isn't initialized at all so we disclose 2 bytes of uninitialized
stack data. We should clear it before passing it to the user.
Fixes: 48365e4852 ('qlcnic: dcb: Add support for CEE Netlink interface.')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
to have a bandwidth of at least this value.
max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
of up to this value.
o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
which takes 4 arguments:
netdev, VF number, min_tx_rate, max_tx_rate
o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.
o Drivers that currently implement ndo_set_vf_tx_rate should now call
ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
implemented by driver.
o If user enters only one of either min_tx_rate or max_tx_rate, then,
userland should read back the other value from driver and set both
for IFLA_VF_RATE.
Drivers that have not yet implemented IFLA_VF_RATE should always
return min_tx_rate as 0 when read from ip tool.
o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
IFLA_VF_RATE should override.
o Idea is to have consistent display of rate values to user.
o Usage example: -
./ip link set p4p1 vf 0 rate 900
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
./ip link set p4p1 vf 0 max_tx_rate 600 rate 300
./ip link show p4p1
32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT qlen 1000
link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
min_tx_rate 200Mbps
vf 1 MAC f6:c6:7c:3f:3d:6c
vf 2 MAC 56:32:43:98:d7:71
vf 3 MAC d6:be:c3:b5:85:ff
vf 4 MAC ee:a9:9a:1e:19:14
vf 5 MAC 4a:d0:4c:07:52:18
vf 6 MAC 3a:76:44:93:62:f9
vf 7 MAC 82:e9:e7:e3:15:1a
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be future-proof and for better readability the time comparisons are modified
to use time_before() instead of plain, error-prone math.
Signed-off-by: Manuel Schölling <manuel.schoelling@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/altera/altera_sgdma.c
net/netlink/af_netlink.c
net/sched/cls_api.c
net/sched/sch_api.c
The netlink conflict dealt with moving to netlink_capable() and
netlink_ns_capable() in the 'net' tree vs. supporting 'tc' operations
in non-init namespaces. These were simple transformations from
netlink_capable to netlink_ns_capable.
The Altera driver conflict was simply code removal overlapping some
void pointer cast cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support to collect RDMEM section of firmware dump
using PEX DMA method.
o This patch uses most of the code used for PEX DMA support
on 83xx series adapters and some refactoring.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o SR-IOV VF can be uplinked to bridge/macvtap device.
Enable mac learning to support communication through
embedded switch.
o Learn vlan filters based on QLCNIC_VLAN_FILTERING flag.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Commands from VF may sleep during PF-VF communication.
Earlier we use to process qlcnic_sriov_vf_set_multi
function in process context. Now individual commands
that are called in atomic context are processed in
process context without waiting for completion of
command.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add support for SR-IOV VF probe in hypervisor to enable
assignment of VFs within hypervisor.
o SR-IOV VF can be uplinked to bridge/macvtap device with this change.
o Refactor SR-IOV enable/disable code. We cannot take rtnl lock
while enabling/disabling SR-IOV as VF probe will take an rtnl
lock.
o Disable spoofchk by default.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1f0f467b67 "qlcnic: Add hwmon interface to export board
temperature" introduced a randconfig build error in the case
when the hwmon framework is built as a module and the qlcnic
driver itself is built-in:
drivers/built-in.o: In function `qlcnic_register_hwmon_dev':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sysfs.c:1301:
undefined reference to `hwmon_device_register_with_groups'
drivers/built-in.o: In function `qlcnic_unregister_hwmon_dev':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sysfs.c:1309:
undefined reference to `hwmon_device_unregister'.
This changes the Kconfig logic to enforce that the qlcnic hwmon
support can only be enabled if it is possible to successfully
build it.
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not set netdev->real_num_tx_queues directly,
let netif_set_real_num_tx_queues() take care of it.
Do not overwrite netdev->num_tx_queues everytime when driver
changes its Tx ring size through ethtool -L and also notify
stack to update number of Rx queues.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o In case of non-multi TX queue mode driver does not initialize "crb_intr_mask" pointer
and driver was accessing that un-initialized pointer while dumping TX queue.
So dump "crb_intr_mask" only when it is initilaized.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o When the driver loads in legacy interrupt mode, only vNICs
with PCI function number 0-7 are supported.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Tx interrupt coalescing parameters can now be set from VF.
o Added validation code in PF to validate the parameters.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Use rx_mac_learn instead of mac_learn and eSwitch flag check in Rx path of
82xx adapter.
* Check for MAC filter overrun only after driver scans through cached MAC address list.
This will help to update the time stamp of cached MAC addresses even if
adapter runs out of MAC address filter limit.
* Remove expensive log thrown by driver when MAC address filters are exhausted
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a newline character appropriately.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o In case QLC_83XX_MBX_CMD_NO_WAIT command type the calling
function does not free the memory as it does not wait for
response. So free it when get a response from adapter after
sending the command.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware versions fails to reset the lock during
initialization. Force reset firmware API lock during driver
probe to ensure lock availability.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function qlcnic_setup_tss_rss_intr() might enter endless
loop in case pci_enable_msix() contiguously returns a
positive number of MSI-Xs that could have been allocated.
Besides, the function contains 'err = -EIO;' assignment
that never could be reached. This update fixes the
aforementioned issues.
Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Dept-HSGLinuxNICDev@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o While disabling SR-IOV when VFs are assigned to VMs causes host crash
so return -EPERM when user request to disable SR-IOV using pci sysfs in
case of VFs are assigned to VMs.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Application expect vNIC number as the array index but driver interface
return configuration in array index form.
o Pack the vNIC information array in the buffer such that application can
access it using vNIC number as the array index.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear older PVID before adding a newer PVID to the eSwicth port
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not read max rings count from qlcnic_get_nic_info(). Use driver defined
values for 82xx adapters. In case of 83xx adapters, use minimum of firmware
provided and driver defined values.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o INIT_NIC_FUNC should be first mailbox sent. Sending DCB capability and
parameter query commands after that command.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o AEN event was being received before initializing delayed_work struct
and handlers for it. This was resulting in crash. This patch fixes it.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qlcnic driver fails to build on ARM with errors like:
In file included from drivers/net/ethernet/qlogic/qlcnic/qlcnic.h:36:0,
from drivers/net/ethernet/qlogic/qlcnic/qlcnic_hw.c:8:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.h:585:1: error: unknown type name 'irqreturn_t'
irqreturn_t qlcnic_83xx_clear_legacy_intr(struct qlcnic_adapter *);
^
Nothing in the driver is explicitly including the irq definitions, so we
add an include of linux/irq.h to pick them up.
Signed-off-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2b3d7b758c687("qlcnic: Add VXLAN Rx offload support") uses
vxlan_get_rx_port() which caused build failure when VXLAN=m.
This patch fixes the build failure by adding dependency on VXLAN
in Kconfig of qlcnic module and use vxlan_get_rx_port() and support
code accordingly.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
qlge driver turns off NETIF_F_HW_CTAG_FILTER, but forgets to
turn off HW_CTAG_TX and HW_CTAG_RX on vlan devices. With the
current settings, q-in-q will only generate a single vlan header.
Remember to mask off CTAG_TX and CTAG_RX features in vlan_features.
CC: Shahed Shaikh <shahed.shaikh@qlogic.com>
CC: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
CC: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting a pointer to a pointer of the same type is pointless,
so remove these unnecessary casts.
Done via coccinelle script:
$ cat typecast_2.cocci
@@
type T;
T *foo;
@@
- (T *)foo
+ foo
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds Rx checksum offload support for VXLAN.
Implements .ndo_{add|del}_vxlan_port netdev ops.
Adapter supports only one VXLAN port, so program adapter with
very first UDP port which VXLAN driver is listening to.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds LSO, LSO6 and Tx checksum offload support for VXLAN
encapsulated packets on 83xx/84xx series adapters.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->tc_cfg[] array has QLC_DCB_MAX_TC (8) elements so the check is
off by one. These functions are always called with valid values though
so it doesn't affect how the code works.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was not re-setting sds ring count to 1 after failing
to allocate msi-x interrupts.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o This patch reverts commit 1414abea04
(qlcnic: Restrict VF from configuring any VLAN mode.)
This will allow same multicast address to be used with any VLAN
instead of programming seperate (MAC, VLAN) tuples in adapter.
This will help save some multicast filters.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once interrupts are enabled, instead of using module parameters,
use flags (QLCNIC_MSI_ENABLED and QLCNIC_MSIX_ENABLED) set by driver
to check interrupt mode.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was treating -ve return value as success in case of
qlcnic_enable_msi_legacy() failure
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter allows vlan0 traffic in case of SR-IOV after setting
QLC_SRIOV_ALLOW_VLAN0 bit even though we do not add vlan0 filters.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qlogic application interface in the driver which has larger than 8 vNIC
configuration support has been updated to handle the following cases:
o Only 8 or lower total vNICs were enabled within the vNIC 0-7 range
o vNICs were enabled in the vNIC 0-15 range such that enabled vNICs were
not contiguous and only 8 or lower number of total VNICs were enabled
o Disconnect in the vNIC mapping between application and driver when the
enabled VNICs were dis contiguous
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Treat firmware minidump template headers for 82xx and 83xx/84xx adapters separately,
as it may change for 82xx and 83xx/84xx adapter type independently.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Cc: Shahed Shaikh <shahed.shaikh@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver was returning from link event handler without
setting linkup variable
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o __qlcnic_down call's netif_tx_disable which in turn stops
all the TX queues, corresponding start queue was missing in
__qlcnic_up which was leading to tx timeout.
o The commit b84caae486
(qlcnic: Fix usage of netif_tx_{wake, stop} api during link change.)
exposed this issue.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not re-initialize vlan list in case of adapter reset.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Bound checks should be >= instead of > for number of receive descriptors
and number of receive rings.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Refactored MSI-x vector calculation for All adapters.
Decoupled logic in the code which was using same call to
request MSI-x vectors in default driver load, as well as
during set_channel() operation for TSS/RSS. This refactoring
simplifies code for TSS/RSS code path as well as probe path
of the driver load for all adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Refactor configuration of interrupt coalescing parameters for
all supported adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MSI/MSI-X mode in poll controller routine.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Added hardware ops for interrupt enable/disable functions
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Dump each Tx queue details with all descriptors, queue indices
and Tx queue stats to imporve data colletion in situations
where Tx timeout occurs.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use boolean type instead of u8.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch changed prototypes, but forgot functions.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove function qlcnic_enable_eswitch which was defined
but never used in current code.
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Functions only used in one file should be static.
Found by running make namespacecheck
Compile tested only.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan gets the same netdev features except vlan filter.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 6878f79a8b
(net: qlcnic: slight optimization of addr compare)
cause a warning "sparse: incorrect type in argument 2
(different type sizes)", so fix it.
I think julia will convert ether_addr_equal to ether_addr_equal_64bits later.
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Enabling BIT_9 while configuring hardware LRO allows adapter to
perform LRO even if destination IP address is not programmed in adapter.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add __QLCNIC_SRIOV_ENABLE bit check before doing SRIOV cleanup
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Refactored code to handle beaconing test for all adapters.
o Use GET_LED_CONFIG mailbox command for 83xx/84xx series adapter
to detect current beaconing state of the adapter.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o MAC learning will be done for SRIOV PF to help program VLAN filters
onto adapter. This will help VNIC traffic to flow through without
flooding traffic.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o By default, SRIOV PF will have promiscous mode on.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o On enabling VF flood bit, PF driver will be able to receive traffic
from all its VFs.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter should allow vlan traffic only for vlans configured on a VF.
On configuring any vlan mode from VF, adapter will allow any vlan
traffic to pass for that VF. Do not allow VF to configure this mode.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmalloc is a limited resource. Don't use it unnecessarily.
It seems this allocation should work with kcalloc.
Remove unnecessary memset(,0,) of buf as it's completely
overwritten as the previously only unset field in
struct qlcnic_pci_func_cfg is now set to 0.
Use kfree instead of vfree.
Use ETH_ALEN instead of 6.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Consider number of Tx queues while calculating the length of
Tx statistics as part of ethtool stats.
o Calculate statistics lenght properly for 82xx and 83xx adapter
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was not updating TX stats so it was not populating
statistics in `ifconfig` command output.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver is using common tx_clean_lock for all Tx queues. This patch
adds per queue tx_clean_lock.
o Driver is not updating sw_consumer while processing Tx completion
when interface is going down. Fixed in this patch.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o TX queues allocation was getting distributed equally among all the
functions of the port including VFs and PF. Which was leading to failure
in PF's multiple TX queues creation.
o Instead of dividing queues equally allocate one TX queue for each VF as VF
doesn't support multiple TX queues.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Adapter requires that if the port is in loopback mode no traffic should
be flowing through that port, so on arrival of Link up AEN, do not advertise
Link up to the stack until port is out of loopback mode
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the possibly more efficient ether_addr_equal or
ether_addr_equal_unaligned to instead of memcmp.
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Manish Chopra <manish.chopra@qlogic.com>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netxen_process_lro() contains two bounds checks. One for the ring number
against the number of rings, and one for the Rx buffer ID against the
array of receive buffers.
Both of these have off-by-one errors, using > instead of >=. The correct
versions are used in netxen_process_rcv(), they're just wrong in
netxen_process_lro().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks the function qlcnic_83xx_clear_legacy_intr_mask(),
qlcnic_83xx_set_legacy_intr_mask() and
qlcnic_83xx_enable_legacy_msix_mbx_intr() in qlcnic_83xx_hw.c as static
because they are not used outside this file.
Thus, it also removes the following warnings
in ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:318:13: warning: no previous prototype for ‘qlcnic_83xx_clear_legacy_intr_mask’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:323:13: warning: no previous prototype for ‘qlcnic_83xx_set_legacy_intr_mask’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c:343:13: warning: no previous prototype for ‘qlcnic_83xx_enable_legacy_msix_mbx_intr’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks the function qlcnic_enable_tx_intr(),
qlcnic_83xx_enable_tx_intr() and qlcnic_83xx_disable_tx_intr() in
qlcnic_io.c as static because they are not used outside this file.
Thus, it also removes the following warnings in
ethernet/qlogic/qlcnic/qlcnic_io.c:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:130:13: warning: no previous prototype for ‘qlcnic_enable_tx_intr’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:147:13: warning: no previous prototype for ‘qlcnic_83xx_enable_tx_intr’ [-Wmissing-prototypes]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_io.c:153:13: warning: no previous prototype for ‘qlcnic_83xx_disable_tx_intr’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend virtual NIC functions from 8 to 16 for 84xx adapter.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Support multiple VLANs on 84xx VF devices
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Allow user to set sigle Tx/Rx queue in MSI-x mode,
for ALL supported adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Change function name from qlcnic_83xx_register_nic_idc_func to
qlcnic_83xx_initialize_nic
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o DCB AEN registration was reissuing INIT_NIC command. Instead, club
all options of INIT NIC command and issue this command only once.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o These operations will be supported only through PFs (SR-IOV and non-SR-IOV).
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not enable mailbox polling in case of legacy interrupt.
Process mailbox AEN/response from the interrupt.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Allow driver to collect firmware dump, during a forced firmware dump
operation, when auto firmware recovery is disabled. Also, during this
operation, driver should not allow reset recovery to be performed.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use vzalloc() instead of kzalloc() for allocation of
bootloader size memory. kzalloc() may fail to allocate
the size of bootloader
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Current code was not allowing the user to configure more
than one Tx ring using ethtool for 83xx/84xx adapter.
This regression was introduced by commit id
18afc102fd ("qlcnic: Enable
multiple Tx queue support for 83xx/84xx Series adapter.")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o TSS/RSS ring validation does not take into account that either
of these ring values can be 0. This patch fixes this validation
and would fail set_channel operation if any of these ring value
is 0. This regression was added as part of commit id
34e8c406fd ("qlcnic: refactor Tx/SDS
ring calculation and validation in driver.")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver should re-allocate all Tx queues after completing
diagnostic tests. This regression was added by commit id
c2c5e3a068 ("qlcnic: Enable
diagnostic test for multiple Tx queues.")
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver was using netif_tx_{stop,wake}_all_queues() api
during link change event. Remove these api calls to
manage queue start/stop event, as core networking stack
will manage this based on netif_carrier_{on,off} call.
These API's were modified as part of commit id
012ec81223 ("qlcnic: Multi Tx
queue support for 82xx Series adapter.")
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
