If devm_clk_get() fails due to probe deferral, we shouldn't print an
error message. Just be silent in this case.
Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Link: https://lkml.kernel.org/r/20191125135910.679310-7-niklas.cassel@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This permits extending the driver to other platforms without having to
modify its source code.
Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Link: https://lkml.kernel.org/r/20191125135910.679310-6-niklas.cassel@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When COMMON_CLK_DISABLED_UNUSED is set, in an effort to save power and
to keep the software model of the clock in line with reality, the
framework transverses the clock tree and disables those clocks that
were enabled by the firmware but have not been enabled by any device
driver.
If CPUFREQ is enabled, early during the system boot, it might attempt
to change the CPU frequency ("set_rate"). If the HFPLL is selected as
a provider, it will then change the rate for this clock.
As boot continues, clk_disable_unused_subtree will run. Since it wont
find a valid counter (enable_count) for a clock that is actually
enabled it will attempt to disable it which will cause the CPU to
stop. Notice that in this driver, calls to check whether the clock is
enabled are routed via the is_enabled callback which queries the
hardware.
The following commit, rather than marking the clock critical and
forcing the clock to be always enabled, addresses the above scenario
making sure the clock is not disabled but it continues to rely on the
firmware to enable the clock.
Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lkml.kernel.org/r/20191125135910.679310-5-niklas.cassel@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Make the output of the high frequency pll a clock provider.
On the QCS404 this PLL controls cpu frequency scaling.
Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20191125135910.679310-4-niklas.cassel@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It turns out booting the modem is dependent on a bimc vote from Linux on
msm8998. To make the modem happy, add the bimc clock to rely on the
default vote from rpmcc. Once we have interconnect support, bimc should
be controlled properly.
Fixes: 6131dc8121 ("clk: qcom: smd: Add support for MSM8998 rpm clocks")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lkml.kernel.org/r/20191217165409.4919-1-jeffrey.l.hugo@gmail.com
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add a driver for the multimedia clock controller found on MSM8998
based devices. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lkml.kernel.org/r/1576596033-10189-1-git-send-email-jhugo@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
gfx3d_clk_src for msm8974 was introduced into the MMCC by
commit d8b212014e ("clk: qcom: Add support for MSM8974's multimedia
clock controller (MMCC)") to ensure that all of the clocks for
this platform are documented upstream. This clock actually belongs
on the RPM. Since then, commit 685dc94b7d ("clk: qcom: smd-rpmcc:
Add msm8974 clocks") was introduced, which contains the proper
definition for gfx3d_clk_src. Let's drop the definition from the
mmcc and register the clock with the rpm instead.
This change was tested on a Nexus 5 (hammerhead) phone.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Link: https://lkml.kernel.org/r/20191115123931.18919-1-masneyb@onstation.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Pull thermal management updates from Zhang Rui:
- Fix a deadlock regression in thermal core framework, which was
introduced in 5.3 (Wei Wang)
- Initialize thermal control framework earlier to enable thermal
mitigation during boot (Amit Kucheria)
- Convert the Intelligent Power Allocator (IPA) thermal governor to
follow the generic PM_EM instead of its own Energy Model (Quentin
Perret)
- Introduce a new Amlogic soc thermal driver (Guillaume La Roque)
- Add interrupt support for tsens thermal driver (Amit Kucheria)
- Add support for MSM8956/8976 in tsens thermal driver
(AngeloGioacchino Del Regno)
- Add support for r8a774b1 in rcar thermal driver (Biju Das)
- Add support for Thermal Monitor Unit v2 in qoriq thermal driver
(Yuantian Tang)
- Some other fixes/cleanups on thermal core framework and soc thermal
drivers (Colin Ian King, Daniel Lezcano, Hsin-Yi Wang, Tian Tao)
* 'thermal/next' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (32 commits)
thermal: Fix deadlock in thermal thermal_zone_device_check
thermal: cpu_cooling: Migrate to using the EM framework
thermal: cpu_cooling: Make the power-related code depend on IPA
PM / EM: Declare EM data types unconditionally
arm64: defconfig: Enable CONFIG_ENERGY_MODEL
drivers: thermal: tsens: fix potential integer overflow on multiply
thermal: cpu_cooling: Reorder the header file
thermal: cpu_cooling: Remove pointless dependency on CONFIG_OF
thermal: no need to set .owner when using module_platform_driver
thermal: qcom: tsens-v1: Fix kfree of a non-pointer value
cpufreq: qcom-hw: Move driver initialization earlier
clk: qcom: Initialize clock drivers earlier
cpufreq: Initialize cpufreq-dt driver earlier
cpufreq: Initialize the governors in core_initcall
thermal: Initialize thermal subsystem earlier
thermal: Remove netlink support
dt: thermal: tsens: Document compatible for MSM8976/56
thermal: qcom: tsens-v1: Add support for MSM8956 and MSM8976
MAINTAINERS: add entry for Amlogic Thermal driver
thermal: amlogic: Add thermal driver to support G12 SoCs
...
The SM8150 list of clks is almost the same as the list for SDM845,
except there isn't an IPA clk. Just point to the SDM845 clks from the
SM8150 list for now so we can reduce the amount of struct bloat in this
driver.
Suggested-by: Vinod Koul <vkoul@kernel.org>
Cc: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20191107214018.184105-1-sboyd@kernel.org
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Some RCGs (the gfx_3d_src_clk in msm8998 for example) are basically just
some constant ratio from the input across the entire frequency range. It
would be great if we could specify the frequency table as a single entry
constant ratio instead of a long list, ie:
{ .src = P_GPUPLL0_OUT_EVEN, .pre_div = 3 },
{ }
So, lets support that.
We need to fix a corner case in qcom_find_freq() where if the freq table
is non-null, but has no frequencies, we end up returning an "entry" before
the table array, which is bad. Then, we need ignore the freq from the
table, and instead base everything on the requested freq.
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lkml.kernel.org/r/20191031185715.15504-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
When MSM8998 support was added, and analysis was done to determine what
clocks would be consumed. That analysis had a flaw, which caused the
pnoc to be skipped. The pnoc clock needs to be on to access the uart
for the console. The clock is on from boot, but has no consumer votes
in the RPM. When we attempt to boot the modem, it causes the RPM to
turn off pnoc, which kills our access to the console and causes CPU hangs.
We need pnoc to be defined, so that clk_smd_rpm_handoff() will put in
an implicit vote for linux and prevent issues when booting modem.
Hopefully pnoc can be consumed by the interconnect framework in future
so that Linux can rely on explicit votes.
Fixes: 6131dc8121 ("clk: qcom: smd: Add support for MSM8998 rpm clocks")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lkml.kernel.org/r/20191107190615.5656-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We need to control five additional clocks and a reset inorder to boot the
modem on msm8998. If we can boot the modem, we have a place to run the
wlan firmware and get wifi up and running.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lkml.kernel.org/r/20191107192136.5880-1-jeffrey.l.hugo@gmail.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the global clock controller found on SC7180
based devices. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lkml.kernel.org/r/20191014102308.27441-6-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Return NULL in the cases where the clk_hw is not registered with the
clock provider, but the clock consumer still requests for a clock id.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lkml.kernel.org/r/20191014102308.27441-3-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Update the init data name for each of the dynamic frequency switch
controlled clock associated with the RCG clock name, so that it can be
generated as per the hardware plan. Thus update the macro accordingly.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lkml.kernel.org/r/20191014102308.27441-2-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the Q6SSTOP clock control used on qcs404
based devices. This would allow wcss remoteproc driver to
control the required WCSS Q6SSTOP clock/reset controls to
bring the subsystem out of reset and shutdown the WCSS Q6DSP.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Link: https://lkml.kernel.org/r/20191011132928.9388-3-govinds@codeaurora.org
[sboyd@kernel.org: Sort makefile]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Initialize the clock drivers on sdm845 and qcs404 in core_initcall so we
can have earlier access to cpufreq during booting.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/75ae9c3a1c0e69b95818c6ffe7181fdeaaf2d70e.1571656015.git.amit.kucheria@linaro.org
clk registration by clk providers and debugfs "nice to haves" for rate
constraints. I'll highlight that we're now setting the clk_init_data pointer
inside struct clk_hw to NULL during clk_register(), which may break some
drivers that thought they could use that pointer during normal operations. That
change has been sitting in next for a while now but maybe something is still
broken. We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support, new
features for existing drivers, and bug fixes scattered throughout. The biggest
diffstat is the Amlogic driver that gained CPU clk support in addition to
migrating to the new way of specifying clk parents. After that the Qualcomm,
i.MX, Mediatek, and Rockchip clk drivers got support for various new SoCs and
clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEE9L57QeeUxqYDyoaDrQKIl8bklSUFAl2FQEMRHHNib3lkQGtl
cm5lbC5vcmcACgkQrQKIl8bklSXHQw//XHnT5DPphpP8ua4x8wuJARdf0n58Vcdb
8fZxxs4QN7uuKhg6aMI4kgwBn+9tgIr65hvN0Gn9Wm5Bsbs3XZvdIo7DvQDrYg7W
NE7192iy2Dg+m+C24YLO7ceZgqVepbjeN+6oeUK88Ui+H+XlOKfJvjfnJ+HxN9Ip
sHnLakIxqlaWvzwTUOHOcsrHyQD2OXupbfNMxLnmr8T/kBh/nqwNEG3aYCppICsg
LpJL9Bv2V3QSk8uBszTgKK5ybWo14aDQPx4rrhgsneD0h7DSnx6M3jvngxMra6W0
fnare4FQlkbPmgAj+XtB7RdCzsuwoke/7TJsvDLQrEbyOYTGnl7bYS8NOSrIg5Tp
w4UPpXrMTQK7e/6okL1OJYAXXYurxep8QjsjpF3nahxC3IVzAZ9uio6ehJrDNEPC
ErqOSPQTMkjOA2npovsQKCH3Mv/yGzAigpsQassPneWwp//NupMLKmmIm6645Xw2
6kqSlVFYz81lhzIylGEQKIoiLcszpB6qqWUzGVt0B94joRbvg0m//8BDaZbHeTqP
m/acRYHRC1utpkAZEnBZRsd79cI+EeuARROUfGsoUMfOueTc4+qQ7Yrjbj4rTvnC
lLM9Qz9h1QkfyRF1IHHPw/fS5twpNTUdO9c1+3qzS3AQfl5dZWpChoF9Um+ycVPR
nQrpk05pHEY=
=z8wK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a small collection of core framework updates this time, mostly
around clk registration by clk providers and debugfs "nice to haves"
for rate constraints. I'll highlight that we're now setting the
clk_init_data pointer inside struct clk_hw to NULL during
clk_register(), which may break some drivers that thought they could
use that pointer during normal operations. That change has been
sitting in next for a while now but maybe something is still broken.
We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support,
new features for existing drivers, and bug fixes scattered throughout.
The biggest diffstat is the Amlogic driver that gained CPU clk support
in addition to migrating to the new way of specifying clk parents.
After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got
support for various new SoCs and clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: Drop !clk checks in debugfs dumping
clk: imx: imx8mn: fix pll mux bit
clk: imx: imx8mm: fix pll mux bit
clk: imx: clk-pll14xx: unbypass PLL by default
clk: imx: pll14xx: avoid glitch when set rate
clk: mvebu: ap80x: add AP807 clock support
clk: mvebu: ap806: Prepare the introduction of AP807 clock support
clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
clk: mvebu: ap806: be more explicit on what SaR is
clk: mvebu: ap80x-cpu: add AP807 CPU clock support
clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
dt-bindings: ap806: Document AP807 clock compatible
dt-bindings: ap80x: Document AP807 CPU clock compatible
clk: sprd: add missing kfree
clk: at91: allow 24 Mhz clock as input for PLL
clk: Make clk_bulk_get_all() return a valid "id"
clk: actions: Fix factor clk struct member access
clk: qcom: rcg: Return failure for RCG update
clk: remove extra ---help--- tags in Kconfig
clk: add include guard to clk-conf.h
...
The max register is 0x23004 as per the manual (the current
max_register that this commit is fixing is actually out of bounds).
Fixes: 892df0191b ("clk: qcom: Add QCS404 TuringCC")
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Link: https://lkml.kernel.org/r/20190909085430.8700-1-jorge.ramirez-ortiz@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for rpmh clocks found in SM8150
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lkml.kernel.org/r/20190826173120.2971-5-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Convert the rpmh clock driver to use the new parent data scheme by
specifying the parent data for board clock.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20190826173120.2971-3-vkoul@kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Update global clock controller SDCC2/4 clocks to use the floor rcg ops,
so as to use the rounded down clock rates for these clocks.
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lkml.kernel.org/r/20190909074410.18977-1-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Some MMC cards fail to enumerate properly when inserted into an MMC slot
on sdm845 devices. This is because the clk ops for qcom clks round the
frequency up to the nearest rate instead of down to the nearest rate.
For example, the MMC driver requests a frequency of 52MHz from
clk_set_rate() but the qcom implementation for these clks rounds 52MHz
up to the next supported frequency of 100MHz. The MMC driver could be
modified to request clk rate ranges but for now we can fix this in the
clk driver by changing the rounding policy for this clk to be round down
instead of round up.
Fixes: 06391eddb6 ("clk: qcom: Add Global Clock controller (GCC) driver for SDM845")
Reported-by: Douglas Anderson <dianders@chromium.org>
Cc: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lkml.kernel.org/r/20190830195142.103564-1-swboyd@chromium.org
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The macro to generate a Bus Controller Manager (BCM) TCS command is used
by the interconnect driver but might also be interesting to other
drivers that need to construct TCS commands for sub processors so move
it out of the sdm845 specific file and into the header.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Georgi Djakov <georgi.djakov@linaro.org>
These aren't useful and they reference the init structure name. Let's
just drop them.
Cc: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190815160020.183334-5-sboyd@kernel.org
Acked-by: Taniya Das <tdas@codeaurora.org>
A future patch is going to change semantics of clk_register() so that
clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid
referencing this member here so that we don't run into NULL pointer
exceptions.
Cc: Taniya Das <tdas@codeaurora.org>
Cc: Andy Gross <agross@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20190731193517.237136-5-sboyd@kernel.org
Acked-by: Taniya Das <tdas@codeaurora.org>
Extend the probe by index API in common code to be used
by other qcom clock controller.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add support for the WCSS QDSP gcc clock control used on qcs404
based devices. This would allow wcss remoteproc driver to control
the required gcc clocks to bring the subsystem out of reset.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
QCOM_A53PLL and QCOM_CLK_APCS_MSM8916 stand out as the only options
built by default. Let's bring them back in line with the rest.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Link: https://lkml.kernel.org/r/d654907d-a3a2-a00f-d6f5-3a34ae25ebcf@free.fr
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Georgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the clocks supported in global clock controller which clock the
peripherals like BLSPs, SDCC, USB, MDSS etc. Register all the clocks
to the clock framework for the clients to be able to request for them.
Signed-off-by: Deepak Katragadda <dkatraga@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[vkoul: port to upstream and tidy-up
port to new parent scheme
Add comments for critical clocks]]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20190722074348.29582-6-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add programming sequence support for managing the Trion
PLLs.
Signed-off-by: Deepak Katragadda <dkatraga@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[vkoul: port to upstream and tidy-up
use upstream way of specifying PLLs]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20190722074348.29582-4-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
We want users to code properly and fix the post_div_table missing and
not rely on core to check. So remove the post_div_table check.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lkml.kernel.org/r/20190722074348.29582-3-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Commit 8f9fab480c ("linux/kernel.h: fix overflow for
DIV_ROUND_UP_ULL") fixed the overflow for DIV_ROUND_UP_ULL, so we no
longer need the cast for DIV_ROUND_UP_ULL, so remove the unnecessary
u64 casts.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20190722074348.29582-2-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
side. The two main highlights in the core framework are the addition of an bulk
clk_get API that handles optional clks and an extra debugfs file that tells the
developer about the current parent of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is mostly
because that SoC has started converting to the clk_hw style of clk
registration. The next big update is in the Amlogic meson clk driver that
gained some support for audio, cpu, and temperature clks while fixing some PLL
issues. Finally, the biggest thing that stands out is the conversion of a large
part of the Allwinner sunxi-ng driver to the new clk parent scheme that uses
less strings and more pointer comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks here and
there to clk data along with the normal addition of a handful of new drivers
and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1
-----BEGIN PGP SIGNATURE-----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=mK0C
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
- Add a 'clk_parent' file in clk debugfs
- Remove dead code in various clk drivers
* clk-debugfs:
clk: Add clk_parent entry in debugfs
* clk-unused:
clk: qcom: Fix -Wunused-const-variable
clk: mmp: frac: Remove set but not used variable 'prev_rate'
clk: ti: Remove unused functions
clk: mediatek: mt8516: Remove unused variable
* clk-refactor:
clk: clk-cdce706: simplify getting the adapter of a client
clk: Simplify clk_core_can_round()
* clk-qoriq:
clk: qoriq: add support for lx2160a
Enabling PCIe requires several of the PCIe related resets from GCC, so
add them all.
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Failing to toggle a GDSC as the driver core is attaching the
power-domain to a device will cause a silent probe deferral. Provide an
explicit warning to the developer, in order to reduce the amount of time
it takes to debug this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Jeffrey Hugo <jhugo@codeaurora.org>
Tested-by: Jeffrey Hugo <jhugo@codeaurora.org>
Reviewed-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
