Add base address for GIC as unit address. This also squashes the
following warnings when built with W=1:
arch/arm/boot/dts/keystone-k2hk-evm.dtb: Warning (unit_address_vs_reg): Node /interrupt-controller has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2l-evm.dtb: Warning (unit_address_vs_reg): Node /interrupt-controller has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2e-evm.dtb: Warning (unit_address_vs_reg): Node /interrupt-controller has a reg or ranges property, but no unit name
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
skeleton.dtsi doesn't offer us any real benefits with most of the
parameters being overridden. So, just drop the same entirely and
introduce appropriate changes for chosen node and memory back to
our top level definition.
This also squashes the following warnings with W=1:
arch/arm/boot/dts/keystone-k2hk-evm.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2l-evm.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2e-evm.dtb: Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Provide a soc0 node and reference the same to simplify dts. This also
resolves the following warnings when built with W=1:
arch/arm/boot/dts/keystone-k2hk-evm.dtb: Warning (unit_address_vs_reg): Node /soc has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2l-evm.dtb: Warning (unit_address_vs_reg): Node /soc has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2e-evm.dtb: Warning (unit_address_vs_reg): Node /soc has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2g-evm.dtb: Warning (unit_address_vs_reg): Node /soc has a reg or ranges property, but no unit name
arch/arm/boot/dts/keystone-k2g-ice.dtb: Warning (unit_address_vs_reg): Node /soc has a reg or ranges property, but no unit name
NOTE: Though we can reformat files by reducing 1 level of indent due to
the use of soc0 phandle, we omit that change to prevent un-necessary
churn in code base.
Reported-by: Rob Herring <robh@kernel.org>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Standardize the licenses with SPDX license tag and standardize TI's
copyright statement to be consistently after file description.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Fix dtc warnings for 'simple_bus_reg' due to leading 0s. Converted using
the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find arch/arm/boot/dts -type -f -name '*.dts*'
Dropped changes to ARM, Ltd. boards LED nodes and manually fixed up some
occurrences of uppercase hex.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since everybody copied my own mistake from the DT binding example,
let's address all the offenders in one swift go.
Most of them got the CPU interface size wrong (4kB, while it should
be 8kB), except for both keystone platforms which got the control
interface wrong (4kB instead of 8kB).
In a few cases where I knew for sure what implementation was used,
I've added the "arm,gic-400" compatible string. I'm 99% sure that
this is what everyone is using, but short of having the TRM for
all the other SoCs, I've left them alone.
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Power Sleep Controller (PSC) module is responsible
for the power and clock management for each of the peripherals
present on the SoC. Represent this as a syscon node so that
multiple users can leverage it for various functionalities.
Signed-off-by: Suman Anna <s-anna@ti.com>
[afd@ti.com: add simple-mfd compatible]
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The TI Keystone SoCs have extra UART registers beyond the standard 8250
registers, so we need a new compatible string to indicate this. Also, at
least one of these registers uses the full 32 bits, so we need to specify
reg-io-width in addition to reg-shift.
"ns16550a" is left in the compatible specification since it does work as
long as the bootloader configures the SoC UART power management registers.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The USB OTG mode is not supported by Kestone 2 devices, as result, the
USB devices enumeration and detection will not work properly when
kernel is built with CONFIG_USB_DWC3_DUAL_ROLE=y (default for multi
platform build):
- it's required to load gadget drivers manually to make host mode
work and this confuses current Keystone 2 users
- device mode is not working, because port can't detect and switch to
peripheral/host mode dynamically.
Hence, specify usb mode explicitly in DT: usb0 = "host" for all KS2
devices and usb1 = "peripheral" for K2E.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Revert commit 51d5d12b8f ("ARM: keystone: dts: add psci command
definition"), which was inadvertently added twice.
Cc: Russell King - ARM Linux <linux@armlinux.org.uk>
Cc: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit adds definition for cpu_on, cpu_off and cpu_suspend
commands. These definitions must match the corresponding PSCI
definitions in boot monitor.
Having those command and corresponding PSCI support in boot monitor
allows run time CPU hot plugin.
Link: http://lkml.kernel.org/r/E1b8koV-0004Hf-2j@rmk-PC.armlinux.org.uk
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Pratyush Anand <panand@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCI DT bindings contain a bogus entry for IO space which is not
supported on Keystone. The current bogus entry has an invalid size
and throws following error during boot.
[0.420713] keystone-pcie 21021000.pcie: error -22: failed to map
resource [io 0x0000-0x400000003fff]
So remove it from the dts. While at it also add a bus-range
value that eliminates following log at boot up.
[0.420659] No bus range found for /soc/pcie@21020000, using [bus 00-ff]
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
This commit adds definition for cpu_on, cpu_off and cpu_suspend commands.
These definitions must match the corresponding PSCI definitions in
boot monitor.
Having those command and corresponding PSCI support in boot monitor allows
run time CPU hot plugin.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add aliases for SPI nodes, this is required to probe the SPI devices in
U-Boot.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add ti,keystone-spi to the compatible field for the SPI node. This new
entry insures that the proper prescaler limit is used for keystone devices
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
These are necessary to get the NIC card working on all Keystone
EVMs. Couple of boards are nroken without these two fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=R5Tu
-----END PGP SIGNATURE-----
Merge tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into fixes
ARM: Couple of Keysyone MDIO DTS fixes for 4.2-rc6+
These are necessary to get the NIC card working on all Keystone
EVMs. Couple of boards are broken without these two fixes.
* tag 'keystone-dts-late-fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: Fix the mdio bindings by moving it to soc specific file
ARM: dts: keystone: fix the clock node for mdio
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently mdio bindings are defined in keystone.dtsi and this results
in incorrect unit address for the node on K2E and K2L SoCs. Fix this
by moving them to SoC specific DTS file.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Currently the MDIO clock is pointing to clkpa instead of clkcpgmac.
MDIO is part of the ethss and the clock should be clkcpgmac.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Now that PCIe DT binding is disabled in SoC specific DTS,
we need a way to override it in a board specific DTS. So
rename the PCIe nodes accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Currently PCIe DT bindings are broken. PCIe driver can't function
without having a SerDes driver that provide the phy configuration.
On K2E EVM, this causes problem since the EVM has Marvell SATA
controller present and with default values in the SerDes register,
it seems to pass the PCIe link check, but causes issues since
the configuration is not correct. The manifestation is that when
EVM is booted with NFS rootfs, the boot hangs. We shouldn't enable
PCIe on this EVM since to work, SerDes driver has to be present as
well. So by default, the PCIe DT binding should be disabled in SoC
specific DTS. It can be enabled in the board specific DTS when the
SerDes device driver is also present.
So fix the status of PCIe DT bindings in the SoC specific DTS to
"disabled". To enable PCIe, the status should be set to "ok" in
the EVM DTS file when SerDes driver support becomes available in
the upstream tree.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add common DT bindings to support PCI controller driver for port 0 on all
of the K2 SoCs that has Synopsis Designware based pcie h/w.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The IO range size is set incorrectly for USB PHY0 deivice
it should be 24 instead of 32. Otherwise, It causes
USB PHY1 probing failure.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add Keystone IRQ controller IP node which allows ARM
CorePac core to receive signals from DSP cores.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The Keystone 2 has MDIO HW block which are compatible
to Davinci SoCs:
See "Gigabit Ethernet (GbE) Switch Subsystem"
See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
Hence, add corresponding DT entry for Keystone 2.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This is a small follow-up to the larger ARM SoC updates merged
last week, almost entirely for the keystone platform.
The main change here is to use the new dma-ranges parsing code
that came in through Russell's ARM tree. This allows the keystone
platform to do cache-coherent DMA and to finally support all the
available physical memory when LPAE is enabled.
Aside from this, the keystone reset driver has been rewritten,
and there is a small bug fix to allow building the orion5x platform
again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=AqkT
-----END PGP SIGNATURE-----
Merge tag 'soc2-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull part two of ARM SoC updates from Arnd Bergmann:
"This is a small follow-up to the larger ARM SoC updates merged last
week, almost entirely for the keystone platform.
The main change here is to use the new dma-ranges parsing code that
came in through Russell's ARM tree. This allows the keystone platform
to do cache-coherent DMA and to finally support all the available
physical memory when LPAE is enabled.
Aside from this, the keystone reset driver has been rewritten, and
there is a small bug fix to allow building the orion5x platform again"
* tag 'soc2-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: Drop use of meminfo since its not available anymore
ARM: orion5x: fix mvebu_mbus_dt_init call
ARM: configs: keystone: enable reset driver support
ARM: dts: keystone: update reset node to work with reset driver
ARM: keystone: remove redundant reset stuff
ARM: keystone: Update the dma offset for non-dt platform devices
ARM: keystone: Switch over to coherent memory address space
ARM: configs: keystone: add MTD_SPI_NOR (new dependency for M25P80)
ARM: configs: keystone: drop CONFIG_COMMON_CLK_DEBUG
The pll controller register set and device state control registers
include sets of registers with different purposes, so it's logically
to add syscon entry to be able to access them from appropriate places.
So added pll controller and device state control syscon entries.
The keystone driver requires the next additional properties:
"ti,syscon-pll" - phandle/offset pair. The phandle to syscon used to
access pll controller registers and the offset to use
reset control registers.
"ti,syscon-dev" - phandle/offset pair. The phandle to syscon used to
access device state control registers and the offset
in order to use mux block registers for all watchdogs.
"ti,wdt-list" - option to declare what watchdogs are used to reboot
the SoC, so set "0" WDT as default.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Keystone supports dma-coherent on USB master and also needs
dma-ranges to specify the hardware alias memory range in which DMA
can be operational.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The dma-ranges property has to be specified per bus and has format:
< DMA addr > - Base DMA address for Bus (Bus format 32-bits)
< CPU addr > - Corresponding base CPU address (CPU format 64-bits)
< DMA range size > - Size of supported DMA range
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
SPI nodes should always have #address-cells and #size-cells defined,
otherwise warnings will be produced in case of adding any child
nodes to the SPI bus in DT:
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/spi@21000400/n25q128a11@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/spi@21000400/n25q128a11@0
Hence, ensure that all SPIx nodes have #address-cells and #size-cells
properties defined.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
I2C devices are not the part of Keystone SoC and have to be
defined in board DTS files.
Hence, move i2c0 EEPROM device node from Keystone SoC to
k2hk, k2e, k2l EVM files as they all have similar EEPROM SoCs
installed.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
I2C nodes should always have #address-cells and #size-cells defined,
otherwise warnings will be produced in case of adding child
nodes to the I2C bus in DT:
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/i2c@2530800/pca@20
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/i2c@2530800/pca@20
Hence, ensure that all i2cX nodes have #address-cells and #size-cells
properties defined.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Current keystone.dtsi includes SoC specific definitions for K2HK
SoCs. In order to support two addition keystone devices, k2 Edison
and K2 Lamarr and corresponding EVMs, This patch restructure the
dts files for the following:-
- All clock nodes that are only available in k2hk SoC are moved
from keystone-clocks.dtsi to a new k2hk-clocks.dtsi include file
- The CPU nodes are now part of the soc specific k2hk.dtsi.
- Change the compatibility string to ti,k2hk-evm and change
the model name accordingly
- Finally include k2hk-clocks.dtsi in k2hk.dtsi and that in
k2hk-evm.dts
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch adds Keystone GPIO IP device definitions in DT which supports
up to 32 GPIO lines and each GPIO line can be configured as separate
interrupt source (so called "unbanked" IRQ).
For more information see:
http://www.ti.com/lit/ug/sprugv1/sprugv1.pdf
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add keystone timer entry to keystone device tree.
This 64-bit timer is used as backup clock event device.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Added device tree support for TI's Keystone USB driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Added device tree support for TI's Keystone USB PHY driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Update the Keystone gic device tree entry to add the maintenance
interrupt information.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Update the Keystone gic node to add the GICV and GIGH address space
needed by the KVM.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch adds K2 Kepler/Hawking evm (k2hk-evm) specific dts file.
To enable re-use of bindings across multiple evms of this family,
rename current keystone.dts to keystone.dtsi and include it in the
evm specific dts file.
K2 SoC has separate ref clock inputs for various clocks. So add
separate ref clock nodes for ARM, DDR3A, DDR3B and PA PLL input
clocks in k2hk-evm.dts. While at it, rename refclkmain to
refclksys based on device User Guide naming convention
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
