Add level active IRQ support to regmap-irq irqchip. Change breaks
existing regmap-irq type setting. Convert the existing drivers which
use regmap-irq with trigger type setting (gpio-max77620) to work
with this new approach. So we do not magically support level-active
IRQs on gpio-max77620 - but add support to the regmap-irq for chips
which support them =)
We do not support distinguishing situation where HW supports rising
and falling edge detection but not both. Separating this would require
inventing yet another flags for IRQ types.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some interrupt controllers use separate bits for controlling rising
and falling edge interrupts in the mask register i.e. they have one
interrupt for rising edge and one for falling.
We already handle the case where we have a single interrupt in the
mask register and a separate type configuration register.
Add a new switch to regmap_irq_chip which tells the framework to use
the mask_base address for configuring the edge of the interrupts that
define type_falling/rising_mask values.
For such interrupts we never update the type_base bits. For interrupts
that don't define type masks or their regmap irq chip doesn't set the
type_in_mask to true everything stays the same.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
if there are lots of irqs for a device and the register addresses for these
irqs is continuous, we can use this macro to initialize regmap_irq value.
Signed-off-by: Tony Xie <tony.xie@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The regmap API had a noinc_read function added for instances where devices
supported returning data from an internal FIFO in a single read.
This commit adds the noinc_write variant to allow writing to a non
incrementing register, this is used in devices such as the sx1301 for
loading firmware.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split regmap_config.use_single_rw into use_single_read and
use_single_write. This change enables drivers of devices which only
support bulk operations in one direction to use the regmap_bulk_*()
functions for both directions and have their bulk operation split into
single operations only when necessary.
Update all struct regmap_config instances where use_single_rw==true to
instead set both use_single_read and use_single_write. No attempt was
made to evaluate whether it is possible to set only one of
use_single_read or use_single_write.
Signed-off-by: David Frey <dpfrey@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices have individual registers that don't autoincrement the
register address during bulk reads but instead repeatedly read the same
value, for example for monitoring GPIOs or ADCs. Add support for these.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltsE8YTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DeLB/sHEWAdyUCz9dO9pDdpi6WfpnKXuCCd
ZFnx8VXBvzVLRCZYGXuMOUEzBQU2lTr2KPFDmE1k4FclyiWaI+hRIJ0s/x8FAl51
EFDoR4TM7t2n2aY0sPQCZKnoAhdQ9YPxlA9JjDUE57h0KoC76Dh8OB44dlAlxUAY
PUjkv64/7AtvkBX7UZPQxckaPOLKM00P/hXwCB9MZCkjqnSWkUGgNCWPgKn9j2yL
jiUQO0Wo9u8RkvYvndHPkh4NzgeH1sUFUdNys/Fopu6C2miIYBNKzvEo2OXhelHf
k5rsoMQXYdiPdy4vRbeaWFetyEeBjxKIAQHKD0WJviFPw8j+ET+2GNjx
=p0Mu
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltsFCwTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0NcxB/wMqH+78D7GdJfMkxMKhCHFUxozfCe9
cgWgZ7+vlWpIwEGvM65FHMrFyc5ZrS3/vD6Hy8lqpsqGBVv6wS6Z0lsoOyj/QvTl
T8USWKvQnvtzlPY5lRZL0xuGiaGGtpGa0eaLKH2lY7uvoge0oHz8VV6ar5y7eA1S
1INBpgTdHJgCQLZoc1pFNOcZ0EMFl6ZAygIWJTpqIwoQlvPEgtCQ4wjPlMUKrevP
psJWd9obyM6+02mYFVMAlYpcMSoZ/MjPeMb7VGhLGwA1BA6dNcbiIeS7GCeH2r/i
/vxvarsEm38MfLBIyORW06onHyRhVwXdLoD1jblmvYtRlfW5ANjr5g/O
=mbi1
-----END PGP SIGNATURE-----
Merge tag 'regmap-noinc-read' into regmap-4.19
regmap: Support non-incrementing registers
Some devices have individual registers that don't autoincrement the
register address during bulk reads but instead repeatedly read the same
value, for example for monitoring GPIOs or ADCs. Add support for these.
The regmap API usually assumes that bulk read operations will read a
range of registers but some I2C/SPI devices have certain registers for
which a such a read operation will return data from an internal FIFO
instead. Add an explicit API to support bulk read without range semantics.
Some linux drivers use regmap_bulk_read or regmap_raw_read for such
registers, for example mpu6050 or bmi150 from IIO. This only happens to
work because when caching is disabled a single regmap read op will map
to a single bus read op (as desired). This breaks if caching is enabled and
reg+1 happens to be a cacheable register.
Without regmap support refactoring a driver to enable regmap caching
requires separate I2C and SPI paths. This is exactly what regmap is
supposed to help avoid.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Crestez Dan Leonard <leonard.crestez@intel.com>
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds Serial Camera Control Bus (SCCB) support for regmap API that
is intended to be used by some of Omnivision sensor drivers.
The ov772x and ov9650 drivers are going to use this SCCB regmap API.
The ov772x driver was previously only worked with the i2c controller
drivers that support I2C_FUNC_PROTOCOL_MANGLING, because the ov772x
device doesn't support repeated starts. After commit 0b964d183c
("media: ov772x: allow i2c controllers without
I2C_FUNC_PROTOCOL_MANGLING"), reading ov772x register is replaced with
issuing two separated i2c messages in order to avoid repeated start.
Using this SCCB regmap hides the implementation detail.
The ov9650 driver also issues two separated i2c messages to read the
registers as the device doesn't support repeated start. So it can
make use of this SCCB regmap.
Cc: Mark Brown <broonie@kernel.org>
Cc: Peter Rosin <peda@axentia.se>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Jacopo Mondi <jacopo+renesas@jmondi.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason the devm variant of slimbus init is not added
into the header eventhough this __devm_regmap_init_slimbus()
is an exported function.
This patch adds this. This also fixes below warning in regmap-slimbus.c
regmap-slimbus.c:65:15: warning: symbol '__devm_regmap_init_slimbus'
was not declared. Should it be static?
regmap-slimbus.c:65:16: warning: no previous prototype for
'__devm_regmap_init_slimbus' [-Wmissing-prototypes]
Fixes: 7d6f7fb053 ("regmap: add SLIMbus support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Similar to the readx_poll_timeout() macro calling ktime_* and using
ktime_t type, which is declared in <linux/ktime.h>. So, make
include/linux/regmap.h explicitly include <linux/ktime.h>, like
include/linux/iopoll.h does. Otherwise, users of the macro will see
below errors.
error: implicit declaration of function ‘ktime_add_us’
[-Werror=implicit-function-declaration]
error: implicit declaration of function ‘ktime_get’
[-Werror=implicit-function-declaration]
error: implicit declaration of function ‘ktime_compare’
[-Werror=implicit-function-declaration]
include/linux/regmap.h:128:2: error: unknown type name ‘ktime_t’
ktime_t __timeout = ktime_add_us(ktime_get(), __timeout_us); \
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
regmap_init_mmio_clk allows to specify a clock that needs to be enabled
while accessing the registers.
However, that clock is retrieved through its clock ID, which means it will
lookup that clock based on the current device that registers the regmap,
and, in the DT case, will only look in that device OF node.
This might be problematic if the clock to enable is stored in another node.
Let's add a function that allows to attach a clock that has already been
retrieved to a regmap in order to fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android binder
fixes, the usual handful of hyper-v updates, and lots of other smaller
driver updates.
All of these have been in linux-next for a long time, with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLuZw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynS4QCcCrPmwfD5PJwaF+q2dPfyKaflkQMAn0x6Wd+u
Gw3Z2scgjETUpwJ9ilnL
=xcQ0
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big pull request for char/misc drivers for 4.16-rc1.
There's a lot of stuff in here. Three new driver subsystems were added
for various types of hardware busses:
- siox
- slimbus
- soundwire
as well as a new vboxguest subsystem for the VirtualBox hypervisor
drivers.
There's also big updates from the FPGA subsystem, lots of Android
binder fixes, the usual handful of hyper-v updates, and lots of other
smaller driver updates.
All of these have been in linux-next for a long time, with no reported
issues"
* tag 'char-misc-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (155 commits)
char: lp: use true or false for boolean values
android: binder: use VM_ALLOC to get vm area
android: binder: Use true and false for boolean values
lkdtm: fix handle_irq_event symbol for INT_HW_IRQ_EN
EISA: Delete error message for a failed memory allocation in eisa_probe()
EISA: Whitespace cleanup
misc: remove AVR32 dependencies
virt: vbox: Add error mapping for VERR_INVALID_NAME and VERR_NO_MORE_FILES
soundwire: Fix a signedness bug
uio_hv_generic: fix new type mismatch warnings
uio_hv_generic: fix type mismatch warnings
auxdisplay: img-ascii-lcd: add missing MODULE_DESCRIPTION/AUTHOR/LICENSE
uio_hv_generic: add rescind support
uio_hv_generic: check that host supports monitor page
uio_hv_generic: create send and receive buffers
uio: document uio_hv_generic regions
doc: fix documentation about uio_hv_generic
vmbus: add monitor_id and subchannel_id to sysfs per channel
vmbus: fix ABI documentation
uio_hv_generic: use ISR callback method
...
All zero read and write masks in the regmap config are used to signal no
special mask is needed and the bus defaults are used. In some devices
all zero read/write masks are the special mask and bus defaults should
not be used. To signal this a new variable is added.
For example SPI often sets bit 7 in address to signal to the device a
read is requested. On TI AFE44xx parts with SPI interfaces no bit
needs to be set as registers are either read or write only and the
operation can be determined from the address only. For this case both
masks must be zero to not effect the address.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SoundWire bus provides sdw_read() and sdw_write() APIs for Slave
devices to program the registers. Provide support in regmap for
SoundWire bus.
Signed-off-by: Hardik T Shah <hardik.t.shah@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the hwlock id 0 is valid for hardware spinlock core, but now id 0
is treated as one invalid value for regmap. Thus we should add one extra
flag for regmap config to indicate if a hardware spinlock should be used,
then id 0 can be valid for regmap to request.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support to read/write SLIMbus value elements.
Currently it only supports byte read/write. Adding this support in
regmap would give codec drivers more flexibility when there are more
than 2 control interfaces like SLIMbus, i2c.
Without this patch each codec driver has to directly call SLIMbus value
element apis, and this could would get messy once we want to add i2c
interface to it.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviwed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have a use case in the at24 EEPROM driver (recently converted to
using regmap instead of raw i2c/smbus calls) where we read from/write
to the regmap in a loop, while protecting the entire loop with
a mutex.
Currently this implicitly makes us use two mutexes - one in the driver
and one in regmap. While browsing the code for similar use cases I
noticed a significant number of places where locking *seems* redundant.
Allow users to completely disable any locking mechanisms in regmap
config.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
On some platforms, when reading or writing some special registers through
regmap, we should acquire one hardware spinlock to synchronize between
the multiple subsystems. Thus this patch adds the hardware spinlock
support for regmap.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we pass the result of a multiplication as the timeout or the delay,
we can get a warning from gcc-7:
drivers/mmc/host/bcm2835.c:596:149: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
drivers/mfd/arizona-core.c:247:195: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
drivers/gpu/drm/sun4i/sun4i_hdmi_i2c.c:49:27: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
The warning is a bit questionable inside of a macro, but this is
intentional on the side of the gcc developers. It is also an indication
of another problem: we evaluate the timeout and sleep arguments multiple
times, which can have undesired side-effects when those are complex
expressions.
This changes the two regmap variants to use local variables for storing
copies of the timeouts. This adds some more type safety, and avoids both
the double-evaluation and the gcc warning.
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81484
Link: http://lkml.kernel.org/r/20170726133756.2161367-1-arnd@arndb.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a macro regmap_field_read_poll_timeout that works
similar to the readx_poll_timeout defined in linux/iopoll.h, except
that this can also return the error value returned by a failed
regmap_field_read.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renamed variable "timeout" to "__timeout" & "pollret" to "__ret" to
avoid namespace collision. Tidy up macro arguments with parentheses.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some irq controllers have writeonly/multipurpose register layouts. In
those cases we read invalid data back. Here we add the option
mask_writeonly as masking option.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most of the kernel-doc comments in regmap don't actually generate
correctly. This patch fixes up a few common issues, corrects some typos
and adds some missing argument descriptions.
The most common issues being using a : after the function name which
causes the short description to not render correctly and not separating
the long and short descriptions of the function. There are quite a few
instances of arguments not being described or given the wrong name as
well.
This patch doesn't fixup functions/structures that are currently missing
descriptions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As almost all of the callers of the regmap_read_poll_timeout macro
will include a local ret variable we will always get a Sparse warning
about the duplication of the ret variable:
warning: symbol 'ret' shadows an earlier one
Simply rename the ret variable in the marco to pollret to make this
significantly less likely to happen.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The readx_poll_timeout() macro calls usleep_range(), which is
declared in <linux/delay.h>.
Make include/linux/regmap.h include <linux/delay.h>, like
include/linux/iopoll.h does. Otherwise, users of the macro
will see "implicit declaration of function 'usleep_range'" error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently only support masking the top bit for read and write
flags. Let's make the mask unsigned long and mask the bytes based
on the configured register length to make things more generic.
This allows using regmap for more exotic combinations like SPI
devices that need little endian addressing.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds a macro regmap_read_poll_timeout that works similar
to the readx_poll_timeout defined in linux/iopoll.h, except that this
can also return the error value returned by a failed regmap_read.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regmap irq implements the generic interrupt service routine which
is common for most of devices. Some devices, like MAX77620, MAX20024
needs the special handling before and after servicing the interrupt
as generic. For the example, MAX77620 programming guidelines for
interrupt servicing says:
1. When interrupt occurs from PMIC, mask the PMIC interrupt by setting
GLBLM.
2. Read IRQTOP and service the interrupt accordingly.
3. Once all interrupts has been checked and serviced, the interrupt
service routine un-masks the hardware interrupt line by clearing
GLBLM.
The step (2) is implemented in regmap irq as generic routine. For
step (1) and (3), add callbacks from regmap irq to client driver
to handle chip specific configurations.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add device managed APIs for regmap_add_irq_chip() and
regmap_del_irq_chip() so that it can be managed by
device framework for freeing it.
This helps on following:
1. Maintaining the sequence of resource allocation and deallocation
regmap_add_irq_chip(&d);
devm_requested_threaded_irq(virq)
On free path:
regmap_del_irq_chip(d);
and then removing the irq registration.
On this case, regmap irq is deleted before the irq is free.
This force to use normal irq registration.
By using devm apis, the sequence can be maintain properly:
devm_regmap_add_irq_chip(&d);
devm_requested_threaded_irq(virq);
and resource deallocation will be done in reverse order
by device framework.
2. No need to delete the regmap_irq_chip in error path or remove
callback and hence there is less code on this path.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 23b92e4cf5fd ("regmap: remove regmap_write_bits()")
removed regmap_write_bits(), but MFD driver was using it.
So, commit e30fccd6771d ("regmap: Keep regmap_write_bits()")
turns out it, but it is using original style.
This patch uses regmap_update_bits_base() for regmap_write_bits()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch merges regmap_fields_update_bits() into macro
by using regmap_field_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch merges regmap_fields_write() into macro
by using regmap_fields_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds new regmap_fields_update_bits_base() which is using
regmap_update_bits_base().
Current regmap_fields_xxx() can be merged into it by macro.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch merges regmap_field_update_bits() into macro
by using regmap_field_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch merges regmap_field_write() into macro
by using regmap_field_update_bits_base().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
