This is used to configure the pins of the sd_emmc_a controller to
which an SDIO module is connected (when available).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic reference driver uses the "mc_val" devicetree property to
configure the PRG_ETHERNET_ADDR0 register. Unfortunately it uses magic
values for this configuration.
According to the datasheet the PRG_ETHERNET_ADDR0 register is at address
0xc8834108. However, the reference driver uses 0xc8834540 instead.
According to my tests, the value from the reference driver is correct.
No changes are required to the board dts files because the only
required configuration option is the phy-mode, which had to be
configured correctly before as well.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All of these have a Realtek Gbit RGMII PHY.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the NVMEM device node in the DTSI.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
[khilman: dropped driver cleanup hunk]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the secure monitor node in the Amlogic Meson GXBB DTSI file to
enable it.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Enable the Infrared Remote Controller on boards which have an Infrared
receiver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the Infrared Remote Controller node so boards with an IR
remote can simply enable it.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the AO clock controller node for the AmLogic GXBB SoC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This reverts commit f3abd62961, which caused a build regression:
arch/arm64/boot/dts/amlogic/meson-gxbb.dtsi:48:41: fatal error: dt-bindings/clock/gxbb-clkc.h: No such file or directory
We should apply this patch one merge window later, once the clk branch
is merged as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the clock controller node for the AmLogic GXBB machine.
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Update DTSI file to add the reset controller node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add node for ethernet interface and pinctrl pins.
Enable on odroid-C2 and P20x boards.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add DT nodes for additional UARTs (UART B & C in EE domain) and add pins
for all EE domain UARTs.
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Update DTS and DTSI files to enable the pin controller. We also now
support the blinking blue LED on the Odroid-C2.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add two new buses in the DTS: hiu and periphs buses.
In the Amlogic S905/GXBB SoC several devices (clock / eth / pin
controllers, etc...) are mapped under these two buses. Add them in the
DT before starting to add new devices.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add minimal DT files for the Amlogic P20x development boards, based on
the Amlogic S905/GXBB SoC.
Cc: Andreas Färber <afaerber@suse.de>
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add minimal DT files for the Hardkernel ODROID-C2 board based on the
Amlogic S905/GXBB SoC.
Used the other gxbb boards from Andreas Färber as a starting point.
Cc: Andreas Färber <afaerber@suse.de>
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Apparently, it's not valid to have an alias point to a disabled device.
Fix this by moving the aliases that are used (serial0) into the files
that use them, and remove aliases to disabled devices (serial1).
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Resolve the following warnings from new dtc by adding the unit address:
DTC arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95-pro.dtb
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
DTC arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95-meta.dtb
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
DTC arch/arm64/boot/dts/amlogic/meson-gxbb-vega-s95-telos.dtb
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Fixes: cc733bc906 ("ARM64: dts: amlogic: Add Tronsmart Vega S95 configs")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Add Device Trees for Tronsmart Vega S95 Pro, Meta and Telos TV boxes.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
