With this patch, the IGMP and MLD message validation functions are moved
from the bridge code to IPv4/IPv6 multicast files. Some small
refactoring was done to enhance readibility and to iron out some
differences in behaviour between the IGMP and MLD parsing code (e.g. the
skb-cloning of MLD messages is now only done if necessary, just like the
IGMP part always did).
Finally, these IGMP and MLD message validation functions are exported so
that not only the bridge can use it but batman-adv later, too.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch divides the IPv6 flow label space into two ranges:
0-7ffff is reserved for flow label manager, 80000-fffff will be
used for creating auto flow labels (per RFC6438). This only affects how
labels are set on transmit, it does not affect receive. This range split
can be disbaled by systcl.
Background:
IPv6 flow labels have been an unmitigated disappointment thus far
in the lifetime of IPv6. Support in HW devices to use them for ECMP
is lacking, and OSes don't turn them on by default. If we had these
we could get much better hashing in IPv6 networks without resorting
to DPI, possibly eliminating some of the motivations to to define new
encaps in UDP just for getting ECMP.
Unfortunately, the initial specfications of IPv6 did not clarify
how they are to be used. There has always been a vague concept that
these can be used for ECMP, flow hashing, etc. and we do now have a
good standard how to this in RFC6438. The problem is that flow labels
can be either stateful or stateless (as in RFC6438), and we are
presented with the possibility that a stateless label may collide
with a stateful one. Attempts to split the flow label space were
rejected in IETF. When we added support in Linux for RFC6438, we
could not turn on flow labels by default due to this conflict.
This patch splits the flow label space and should give us
a path to enabling auto flow labels by default for all IPv6 packets.
This is an API change so we need to consider compatibility with
existing deployment. The stateful range is chosen to be the lower
values in hopes that most uses would have chosen small numbers.
Once we resolve the stateless/stateful issue, we can proceed to
look at enabling RFC6438 flow labels by default (starting with
scaled testing).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In my earlier commit:
653437d02f ("ipv6: Stop /128 route from disappearing after pmtu update"),
there was a horrible typo. Instead of checking RTF_LOCAL on
rt->rt6i_flags, it was checked on rt->dst.flags. This patch fixes
it.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hajime Tazaki <tazaki@sfc.wide.ad.jp>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
_rt6i_peer is no longer needed after the last patch,
'ipv6: Stop rt6_info from using inet_peer's metrics'.
DST_METRICS_FORCE_OVERWRITE is added by
commit e5fd387ad5 ("ipv6: do not overwrite inetpeer metrics prematurely").
Since inetpeer is no longer used for metrics, this bit is also not needed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Michal Kubeček <mkubecek@suse.cz>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_peer is indexed by the dst address alone. However, the fib6 tree
could have multiple routing entries (rt6_info) for the same dst. For
example,
1. A /128 dst via multiple gateways.
2. A RTF_CACHE route cloned from a /128 route.
In the above cases, all of them will share the same metrics and
step on each other.
This patch will steer away from inet_peer's metrics and use
dst_cow_metrics_generic() for everything.
Change Highlights:
1. Remove rt6_cow_metrics() which currently acquires metrics from
inet_peer for DST_HOST route (i.e. /128 route).
2. Add rt6i_pmtu to take care of the pmtu update to avoid creating a
full size metrics just to override the RTAX_MTU.
3. After (2), the RTF_CACHE route can also share the metrics with its
dst.from route, by:
dst_init_metrics(&cache_rt->dst, dst_metrics_ptr(cache_rt->dst.from), true);
4. Stop creating RTF_CACHE route by cloning another RTF_CACHE route. Instead,
directly clone from rt->dst.
[ Currently, cloning from another RTF_CACHE is only possible during
rt6_do_redirect(). Also, the old clone is removed from the tree
immediately after the new clone is added. ]
In case of cloning from an older redirect RTF_CACHE, it should work as
before.
In case of cloning from an older pmtu RTF_CACHE, this patch will forget
the pmtu and re-learn it (if there is any) from the redirected route.
The _rt6i_peer and DST_METRICS_FORCE_OVERWRITE will be removed
in the next cleanup patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is mostly from Steffen Klassert <steffen.klassert@secunet.com>.
I only removed the (rt6->rt6i_dst.plen == 128) check from
ip6_rt_update_pmtu() because the (rt6->rt6i_flags & RTF_CACHE) test
has already implied it.
This patch:
1. Create RTF_CACHE route for /128 non local route
2. After (1), all routes that allow pmtu update should have a RTF_CACHE
clone. Hence, stop updating MTU for any non RTF_CACHE route.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We search only for routes with highest priority metric in
find_rr_leaf(). However if one of these routes is marked
as invalid, we may fail to find a route even if there is
a appropriate route with lower priority. Then we loose
connectivity until the garbage collector deletes the
invalid route. This typically happens if a host route
expires afer a pmtu event. Fix this by searching also
for routes with a lower priority metric.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a prep work for the later bug-fix patch which will stop /128 route
from disappearing after pmtu update.
The later bug-fix patch will allow a /128 route and its RTF_CACHE clone
both exist at the same fib6_node. To do this, we need to prepare the
existing fib6 tree search to expect RTF_CACHE for /128 route.
Note that the fn->leaf is sorted by rt6i_metric. Hence,
RTF_CACHE (if there is any) is always at the front. This property
leads to the following:
1. When doing ip6_route_del(), it should honor the RTF_CACHE flag which
the caller is used to ask for deleting clone or non-clone.
The rtm_to_fib6_config() should also check the RTM_F_CLONED and
then set RTF_CACHE accordingly so that:
- 'ip -6 r del...' will make ip6_route_del() to delete a route
and all its clones. Note that its clones is flushed by fib6_del()
- 'ip -6 r flush table cache' will make ip6_route_del() to
only delete clone(s).
2. Exclude RTF_CACHE from addrconf_get_prefix_route() which
should not configure on a cloned route.
3. No change is need for rt6_device_match() since it currently could
return a RTF_CACHE clone route, so the later bug-fix patch will not
affect it.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ 3897.923145] BUG: unable to handle kernel NULL pointer dereference at
0000000000000080
[ 3897.931025] IP: [<ffffffffa9f27686>] reqsk_timer_handler+0x1a6/0x243
There is a race when reqsk_timer_handler() and tcp_check_req() call
inet_csk_reqsk_queue_unlink() on the same req at the same time.
Before commit fa76ce7328 ("inet: get rid of central tcp/dccp listener
timer"), listener spinlock was held and race could not happen.
To solve this bug, we change reqsk_queue_unlink() to not assume req
must be found, and we return a status, to conditionally release a
refcount on the request sock.
This also means tcp_check_req() in non fastopen case might or not
consume req refcount, so tcp_v6_hnd_req() & tcp_v4_hnd_req() have
to properly handle this.
(Same remark for dccp_check_req() and its callers)
inet_csk_reqsk_queue_drop() is now too big to be inlined, as it is
called 4 times in tcp and 3 times in dccp.
Fixes: fa76ce7328 ("inet: get rid of central tcp/dccp listener timer")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code there just open-codes the same, so use the provided macro instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
A final pull request, I know it's very late but this time I think it's worth a
bit of rush.
The following patchset contains Netfilter/nf_tables updates for net-next, more
specifically concatenation support and dynamic stateful expression
instantiation.
This also comes with a couple of small patches. One to fix the ebtables.h
userspace header and another to get rid of an obsolete example file in tree
that describes a nf_tables expression.
This time, I decided to paste the original descriptions. This will result in a
rather large commit description, but I think these bytes to keep.
Patrick McHardy says:
====================
netfilter: nf_tables: concatenation support
The following patches add support for concatenations, which allow multi
dimensional exact matches in O(1).
The basic idea is to split the data registers, currently consisting of
4 registers of 16 bytes each, into smaller units, 16 registers of 4
bytes each, and making sure each register store always leaves the
full 32 bit in a well defined state, meaning smaller stores will
zero the remaining bits.
Based on that, we can load multiple adjacent registers with different
values, thereby building a concatenated bigger value, and use that
value for set lookups.
Sets are changed to use variable sized extensions for their key and
data values, removing the fixed limit of 16 bytes while saving memory
if less space is needed.
As a side effect, these patches will allow some nice optimizations in
the future, like using jhash2 in nft_hash, removing the masking in
nft_cmp_fast, optimized data comparison using 32 bit word size etc.
These are not done so far however.
The patches are split up as follows:
* the first five patches add length validation to register loads and
stores to make sure we stay within bounds and prepare the validation
functions for the new addressing mode
* the next patches prepare for changing to 32 bit addressing by
introducing a struct nft_regs, which holds the verdict register as
well as the data registers. The verdict members are moved to a new
struct nft_verdict to allow to pull struct nft_data out of the stack.
* the next patches contain preparatory conversions of expressions and
sets to use 32 bit addressing
* the next patch introduces so far unused register conversion helpers
for parsing and dumping register numbers over netlink
* following is the real conversion to 32 bit addressing, consisting of
replacing struct nft_data in struct nft_regs by an array of u32s and
actually translating and validating the new register numbers.
* the final two patches add support for variable sized data items and
variable sized keys / data in set elements
The patches have been verified to work correctly with nft binaries using
both old and new addressing.
====================
Patrick McHardy says:
====================
netfilter: nf_tables: dynamic stateful expression instantiation
The following patches are the grand finale of my nf_tables set work,
using all the building blocks put in place by the previous patches
to support something like iptables hashlimit, but a lot more powerful.
Sets are extended to allow attaching expressions to set elements.
The dynset expression dynamically instantiates these expressions
based on a template when creating new set elements and evaluates
them for all new or updated set members.
In combination with concatenations this effectively creates state
tables for arbitrary combinations of keys, using the existing
expression types to maintain that state. Regular set GC takes care
of purging expired states.
We currently support two different stateful expressions, counter
and limit. Using limit as a template we can express the functionality
of hashlimit, but completely unrestricted in the combination of keys.
Using counter we can perform accounting for arbitrary flows.
The following examples from patch 5/5 show some possibilities.
Userspace syntax is still WIP, especially the listing of state
tables will most likely be seperated from normal set listings
and use a more structured format:
1. Limit the rate of new SSH connections per host, similar to iptables
hashlimit:
flow ip saddr timeout 60s \
limit 10/second \
accept
2. Account network traffic between each set of /24 networks:
flow ip saddr & 255.255.255.0 . ip daddr & 255.255.255.0 \
counter
3. Account traffic to each host per user:
flow skuid . ip daddr \
counter
4. Account traffic for each combination of source address and TCP flags:
flow ip saddr . tcp flags \
counter
The resulting set content after a Xmas-scan look like this:
{
192.168.122.1 . fin | psh | urg : counter packets 1001 bytes 40040,
192.168.122.1 . ack : counter packets 74 bytes 3848,
192.168.122.1 . psh | ack : counter packets 35 bytes 3144
}
In the future the "expressions attached to elements" will be extended
to also support user created non-stateful expressions to allow to
efficiently select beween a set of parameter sets, f.i. a set of log
statements with different prefixes based on the interface, which currently
require one rule each. This will most likely have to wait until the next
kernel version though.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-socfpga.c conflict was a case of a bug fix overlapping
changes in net-next to handle an error pointer differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a timer wheel for timewait sockets was nice ~15 years ago when
memory was expensive and machines had a single processor.
This does not scale, code is ugly and source of huge latencies
(Typically 30 ms have been seen, cpus spinning on death_lock spinlock.)
We can afford to use an extra 64 bytes per timewait sock and spread
timewait load to all cpus to have better behavior.
Tested:
On following test, /proc/sys/net/ipv4/tcp_tw_recycle is set to 1
on the target (lpaa24)
Before patch :
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
419594
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
437171
While test is running, we can observe 25 or even 33 ms latencies.
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 20601ms
rtt min/avg/max/mdev = 0.020/0.217/25.771/1.535 ms, pipe 2
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 20702ms
rtt min/avg/max/mdev = 0.019/0.183/33.761/1.441 ms, pipe 2
After patch :
About 90% increase of throughput :
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
810442
lpaa23:~# ./super_netperf 200 -H lpaa24 -t TCP_CC -l 60 -- -p0,0
800992
And latencies are kept to minimal values during this load, even
if network utilization is 90% higher :
lpaa24:~# ping -c 1000 -i 0.02 -qn lpaa23
...
1000 packets transmitted, 1000 received, 0% packet loss, time 19991ms
rtt min/avg/max/mdev = 0.023/0.064/0.360/0.042 ms
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the nf_tables registers from 128 bit addressing to 32 bit
addressing to support so called concatenations, where multiple values
can be concatenated over multiple registers for O(1) exact matches of
multiple dimensions using sets.
The old register values are mapped to areas of 128 bits for compatibility.
When dumping register numbers, values are expressed using the old values
if they refer to the beginning of a 128 bit area for compatibility.
To support concatenations, register loads of less than a full 32 bit
value need to be padded. This mainly affects the payload and exthdr
expressions, which both unconditionally zero the last word before
copying the data.
Userspace fully passes the testsuite using both old and new register
addressing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Replace the array of registers passed to expressions by a struct nft_regs,
containing the verdict as a seperate member, which aliases to the
NFT_REG_VERDICT register.
This is needed to seperate the verdict from the data registers completely,
so their size can be changed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree.
They are:
* nf_tables set timeout infrastructure from Patrick Mchardy.
1) Add support for set timeout support.
2) Add support for set element timeouts using the new set extension
infrastructure.
4) Add garbage collection helper functions to get rid of stale elements.
Elements are accumulated in a batch that are asynchronously released
via RCU when the batch is full.
5) Add garbage collection synchronization helpers. This introduces a new
element busy bit to address concurrent access from the netlink API and the
garbage collector.
5) Add timeout support for the nft_hash set implementation. The garbage
collector peridically checks for stale elements from the workqueue.
* iptables/nftables cgroup fixes:
6) Ignore non full-socket objects from the input path, otherwise cgroup
match may crash, from Daniel Borkmann.
7) Fix cgroup in nf_tables.
8) Save some cycles from xt_socket by skipping packet header parsing when
skb->sk is already set because of early demux. Also from Daniel.
* br_netfilter updates from Florian Westphal.
9) Save frag_max_size and restore it from the forward path too.
10) Use a per-cpu area to restore the original source MAC address when traffic
is DNAT'ed.
11) Add helper functions to access physical devices.
12) Use these new physdev helper function from xt_physdev.
13) Add another nf_bridge_info_get() helper function to fetch the br_netfilter
state information.
14) Annotate original layer 2 protocol number in nf_bridge info, instead of
using kludgy flags.
15) Also annotate the pkttype mangling when the packet travels back and forth
from the IP to the bridge layer, instead of using a flag.
* More nf_tables set enhancement from Patrick:
16) Fix possible usage of set variant that doesn't support timeouts.
17) Avoid spurious "set is full" errors from Netlink API when there are pending
stale elements scheduled to be released.
18) Restrict loop checks to set maps.
19) Add support for dynamic set updates from the packet path.
20) Add support to store optional user data (eg. comments) per set element.
BTW, I have also pulled net-next into nf-next to anticipate the conflict
resolution between your okfn() signature changes and Florian's br_netfilter
updates.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
More recent GCC warns about two kinds of switch statement uses:
1) Switching on an enumeration, but not having an explicit case
statement for all members of the enumeration. To show the
compiler this is intentional, we simply add a default case
with nothing more than a break statement.
2) Switching on a boolean value. I think this warning is dumb
but nevertheless you get it wholesale with -Wswitch.
This patch cures all such warnings in netfilter.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fixes: 79b16aadea ("udp_tunnel: Pass UDP socket down through udp_tunnel{, 6}_xmit_skb().")
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
right now we store this in the nf_bridge_info struct, accessible
via skb->nf_bridge. This patch prepares removal of this pointer from skb:
Instead of using skb->nf_bridge->x, we use helpers to obtain the in/out
device (or ifindexes).
Followup patches to netfilter will then allow nf_bridge_info to be
obtained by a call into the br_netfilter core, rather than keeping a
pointer to it in sk_buff.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
That was we can make sure the output path of ipv4/ipv6 operate on
the UDP socket rather than whatever random thing happens to be in
skb->sk.
Based upon a patch by Jiri Pirko.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
On the output paths in particular, we have to sometimes deal with two
socket contexts. First, and usually skb->sk, is the local socket that
generated the frame.
And second, is potentially the socket used to control a tunneling
socket, such as one the encapsulates using UDP.
We do not want to disassociate skb->sk when encapsulating in order
to fix this, because that would break socket memory accounting.
The most extreme case where this can cause huge problems is an
AF_PACKET socket transmitting over a vxlan device. We hit code
paths doing checks that assume they are dealing with an ipv4
socket, but are actually operating upon the AF_PACKET one.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the kernel deleted a vti6 interface, this interface was not removed from
the tunnels list. Thus, when the ip6_vti module was removed, this old interface
was found and the kernel tried to delete it again. This was leading to a kernel
panic.
Fixes: 61220ab349 ("vti6: Enable namespace changing")
Signed-off-by: Yao Xiwei <xiwei.yao@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/cmd.c
net/core/fib_rules.c
net/ipv4/fib_frontend.c
The fib_rules.c and fib_frontend.c conflicts were locking adjustments
in 'net' overlapping addition and removal of code in 'net-next'.
The mlx4 conflict was a bug fix in 'net' happening in the same
place a constant was being replaced with a more suitable macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not consult skb->sk for output decisions in xmit recursion
levels > 0 in the stack. Otherwise local socket settings could influence
the result of e.g. tunnel encapsulation process.
ipv6 does not conform with this in three places:
1) ip6_fragment: we do consult ipv6_npinfo for frag_size
2) sk_mc_loop in ipv6 uses skb->sk and checks if we should
loop the packet back to the local socket
3) ip6_skb_dst_mtu could query the settings from the user socket and
force a wrong MTU
Furthermore:
In sk_mc_loop we could potentially land in WARN_ON(1) if we use a
PF_PACKET socket ontop of an IPv6-backed vxlan device.
Reuse xmit_recursion as we are currently only interested in protecting
tunnel devices.
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
That way we don't have to reinstantiate another nf_hook_state
on the stack of the nf_reinject() path.
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to wait for the flying timers, since we
are going to free the mrtable right after it.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to hold rtnl lock for fib_rules_unregister()
otherwise the following race could happen:
fib_rules_unregister(): fib_nl_delrule():
... ...
... ops = lookup_rules_ops();
list_del_rcu(&ops->list);
list_for_each_entry(ops->rules) {
fib_rules_cleanup_ops(ops); ...
list_del_rcu(); list_del_rcu();
}
Note, net->rules_mod_lock is actually not needed at all,
either upper layer netns code or rtnl lock guarantees
we are safe.
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
drivers/net/usb/sr9800.c
drivers/net/usb/usbnet.c
include/linux/usb/usbnet.h
net/ipv4/tcp_ipv4.c
net/ipv6/tcp_ipv6.c
The TCP conflicts were overlapping changes. In 'net' we added a
READ_ONCE() to the socket cached RX route read, whilst in 'net-next'
Eric Dumazet touched the surrounding code dealing with how mini
sockets are handled.
With USB, it's a case of the same bug fix first going into net-next
and then I cherry picked it back into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use dev->iflink anymore.
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use dev->iflink anymore.
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to prepare the removal of the iflink field. It
introduces a new ndo function, which will be implemented by virtual interfaces.
There is no functional change into this patch. All readers of iflink field
now call dev_get_iflink().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those are counterparts to nla_put_in_addr and nla_put_in6_addr.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP addresses are often stored in netlink attributes. Add generic functions
to do that.
For nla_put_in_addr, it would be nicer to pass struct in_addr but this is
not used universally throughout the kernel, in way too many places __be32 is
used to store IPv4 address.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In many places, the a6 field is typecasted to struct in6_addr. As the
fields are in union anyway, just add in6_addr type to the union and
get rid of the typecasting.
Modifying the uapi header is okay, the union has still the same size.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 code uses a mixture of coding styles. In some instances check for NULL
pointer is done as x != NULL and sometimes as x. x is preferred according to
checkpatch and this patch makes the code consistent by adopting the latter
form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 code uses a mixture of coding styles. In some instances check for NULL
pointer is done as x == NULL and sometimes as !x. !x is preferred according to
checkpatch and this patch makes the code consistent by adopting the latter
form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_v6_fill_cb() will be called twice if socket's state changes from
TCP_TIME_WAIT to TCP_LISTEN. That can result in control buffer data
corruption because in the second tcp_v6_fill_cb() call it's not copying
IP6CB(skb) anymore, but 'seq', 'end_seq', etc., so we can get weird and
unpredictable results. Performance loss of up to 1200% has been observed
in LTP/vxlan03 test.
This can be fixed by copying inet6_skb_parm to the beginning of 'cb'
only if xfrm6_policy_check() and tcp_v6_fill_cb() are going to be
called again.
Fixes: 2dc49d1680 ("tcp6: don't move IP6CB before xfrm6_policy_check()")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next tree.
Basically, nf_tables updates to add the set extension infrastructure and finish
the transaction for sets from Patrick McHardy. More specifically, they are:
1) Move netns to basechain and use recently added possible_net_t, from
Patrick McHardy.
2) Use LOGLEVEL_<FOO> from nf_log infrastructure, from Joe Perches.
3) Restore nf_log_trace that was accidentally removed during conflict
resolution.
4) nft_queue does not depend on NETFILTER_XTABLES, starting from here
all patches from Patrick McHardy.
5) Use raw_smp_processor_id() in nft_meta.
Then, several patches to prepare ground for the new set extension
infrastructure:
6) Pass object length to the hash callback in rhashtable as needed by
the new set extension infrastructure.
7) Cleanup patch to restore struct nft_hash as wrapper for struct
rhashtable
8) Another small source code readability cleanup for nft_hash.
9) Convert nft_hash to rhashtable callbacks.
And finally...
10) Add the new set extension infrastructure.
11) Convert the nft_hash and nft_rbtree sets to use it.
12) Batch set element release to avoid several RCU grace period in a row
and add new function nft_set_elem_destroy() to consolidate set element
release.
13) Return the set extension data area from nft_lookup.
14) Refactor existing transaction code to add some helper functions
and document it.
15) Complete the set transaction support, using similar approach to what we
already use, to activate/deactivate elements in an atomic fashion.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not commit the new ops until we finish
all the setup, otherwise we have to NULL it on failure.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As namespaces are sometimes used with overlapping ip address ranges,
we should also use the namespace as input to the hash to select the ip
fragmentation counter bucket.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A local route may have a lower hop_limit set than global routes do.
RFC 3756, Section 4.2.7, "Parameter Spoofing"
> 1. The attacker includes a Current Hop Limit of one or another small
> number which the attacker knows will cause legitimate packets to
> be dropped before they reach their destination.
> As an example, one possible approach to mitigate this threat is to
> ignore very small hop limits. The nodes could implement a
> configurable minimum hop limit, and ignore attempts to set it below
> said limit.
Signed-off-by: D.S. Ljungmark <ljungmark@modio.se>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the #defines where appropriate.
Miscellanea:
Add explicit #include <linux/kernel.h> where it was not
previously used so that these #defines are a bit more
explicitly defined instead of indirectly included via:
module.h->moduleparam.h->kernel.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
