Pull libata updates from Tejun Heo:
"Mostly low level driver specific changes.
Two changes are somewhat noteworthy. First, Dan's patchset to support
per-port msix interrupt handling for ahci, which was tried last cycle
but had to be backed out due to a couple issues, is back and seems to
be working fine. Second, libata exception handling now uses
usleep_range() instead of msleep() for sleeps < 20ms which can make
things snappier in some corner cases"
* 'for-4.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: skip debounce delay on link resume
ata: ahci_brcmstb: disable DIPM support
ata: ahci_brcmstb: enable support for ALPM
drivers: libata-core: Use usleep_range() instead of msleep() for short sleeps (<20 ms)
sata_sx4: correctly handling failed allocation
ata: ahci_brcmstb: add support for MIPS-based platforms
ahci: qoriq: Adjust the default register values on ls1021a
ahci: qoriq: Update the default Rx watermark value
ahci: qoriq: Adjust the default register values on ls1043a
ahci: compile out msi/msix infrastructure
ata: core: fix irq description on AHCI single irq systems
ata: ahci_brcmstb: remove unused definitions
ata: ahci_brcmstb: add a quirk for MIPS-based platforms
ata: ahci_brcmstb: disable NCQ for MIPS-based platforms
ata: sata_rcar: Remove obsolete platform_device_id entries
sata_rcar: Add compatible string for r8a7795
ahci: kill 'intr_status'
ahci: switch from 'threaded' to 'hardirq' interrupt handling
ahci: per-port msix support
The link resume logic uses a 200msec delay while debouncing
the SControl register. The rationale behind that delay is
to accommodate some PHYs that behave badly if their SStatus/
SControl registers are pounded immediately on resume.
The Broadcom STB SATA PHY does not seem to have this issue.
This patch introduces a new link flag that allows platforms
to skip the debounce delay if it isn't needed.
Signed-off-by: Danesh Petigara <dpetigara@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some controller lockup on a ata_read_log_page.
Add new ata port flag ATA_FLAG_NO_LOG_PAGE which can used
to blacklist a controller.
If this flag is set, any attempt to read a log page returns an error
without actually issuing the command.
Signed-off-by: Andreas Werner <andreas.werner@men.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
If the AHCI ports' HPCP or ESP bits are set, the port
should be considered external (e.g. eSATA) and is marked
as removable. Userspace tools like udisks then treat it
like an usb drive.
With this patch applied, when I plug a drive into the esata port,
KDE pops up a window asking what to do with the drives(s), just
like it does for any random USB stick.
Removability is indicated to the upper layers by way of the
SCSI RMB bit, as I haven't found another way to signal
userspace to treat a sata disk like any usb stick.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since no longer limiting max_sectors to BLK_DEF_MAX_SECTORS (commit 34b48db66e),
data corruption may occur on ST380013AS drive configured on 82801JI (ICH10 Family)
SATA controller. This patch will allow the driver to limit max_sectors as before
# cat /sys/block/sdb/queue/max_sectors_kb
512
I was able to double the max_sectors_kb value up to 16384 on linux-4.2.0-rc2
before seeing corruption, but seems safer to use previous limit. Without this
patch max_sectors_kb will be 32767.
tj: Minor comment update.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v3.19 and later
Fixes: 34b48db66e ("block: remove artifical max_hw_sectors cap")
Some devices lose data on TRIM whether queued or not. This patch adds
a horkage to disable TRIM.
tj: Collapsed unnecessary if() nesting.
Signed-off-by: Arne Fitzenreiter <arne_f@ipfire.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Pull libata updates from Tejun Heo:
- a number of libata core changes to better support NCQ TRIM.
- ahci now supports MSI-X in single IRQ mode to support a new
controller which doesn't implement MSI or INTX.
- ahci now supports edge-triggered IRQ mode to support a new controller
which for some odd reason did edge-triggered IRQ.
- the usual controller support additions and changes.
* 'for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (27 commits)
libata: Do not blacklist Micron M500DC
ata: ahci_mvebu: add suspend/resume support
ahci, msix: Fix build error for !PCI_MSI
ahci: Add support for Cavium's ThunderX host controller
ahci: Add generic MSI-X support for single interrupts to SATA PCI driver
libata: finally use __initconst in ata_parse_force_one()
drivers: ata: add support for Ceva sata host controller
devicetree:bindings: add devicetree bindings for ceva ahci
ahci: added support for Freescale AHCI sata
ahci: Store irq number in struct ahci_host_priv
ahci: Move interrupt enablement code to a separate function
Doc: libata: Fix spelling typo found in libata.xml
ata:sata_nv - Change 1 to true for bool type variable.
ata: add Broadcom AHCI SATA3 driver for STB chips
Documentation: devicetree: add Broadcom SATA binding
libata: Fix regression when the NCQ Send and Receive log page is absent
ata: hpt366: fix constant cast warning
ata: ahci_xgene: potential NULL dereference in probe
ata: ahci_xgene: Add AHCI Support for 2nd HW version of APM X-Gene SoC AHCI SATA Host controller.
libahci: Add support to handle HOST_IRQ_STAT as edge trigger latch.
...
This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There are also one new driver: the Cisco snic; the advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions).
Signed-off-by: James Bottomley <JBottomley@Odin.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJViKWdAAoJEDeqqVYsXL0MAr8IAMmlA6HBVjMJJFCEOY9corHj
e70MNQa7LUgf+JCdOtzGcvHXTiFFd4IHZAwXUJAnsC4IU2QWEfi1bjUTErlqBIGk
LoZlXXpEHnFpmWot3OluOzzcGcxede8rVgPiKWVVdojIngBC2+LL/i2vPCJ84ri9
WCVlk6KBvWZXuU6JuOKAb2FO9HOX7Q61wuKAMast2Qc6RNc2ksgc7VbstsITqzZ9
FVEsjmQ5lqUj+xdxBpiUOdUpc22IJ4VcpBgQ2HrThvg6vf4aq937RJ/g4vi/g0SU
Utk0a3bUw1H/WnYAfJVFx83nVEsS/954Z7/ERDg1sjlfLYwQtQnpov0XIbPIbZU=
=k9IT
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
'0' is now used as the default cmd_per_lun value,
so there's no need to explicitly set it to '1' in the
host template.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Some devices advertise support for the READ/WRITE LOG DMA EXT commands
but fail when we try to issue them. This can lead to queued TRIM being
unintentionally disabled since the relevant feature flag is located in a
general purpose log page.
Fall back to unqueued READ LOG EXT if the DMA variant fails while
reading a log page.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
When the LPM policy is set to ATA_LPM_MAX_POWER, the device might
generate a spurious PHY event that cuases errors on the link.
Ignore this event if it occured within 10s after the policy change.
The timeout was chosen observing that on a Dell XPS13 9333 these
spurious events can occur up to roughly 6s after the policy change.
Link: http://lkml.kernel.org/g/3352987.ugV1Ipy7Z5@xps13
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This is a preparation commit that will allow to add other criteria
according to which PHY events should be dropped.
Signed-off-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Pull libata updates from Tejun Heo:
- Hannes's patchset implements support for better error reporting
introduced by the new ATA command spec.
- the deperecated pci_ dma API usages have been replaced by dma_ ones.
- a bunch of hardware specific updates and some cleanups.
* 'for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: remove deprecated use of pci api
ahci: st: st_configure_oob must be called after IP is clocked.
ahci: st: Update the ahci_st DT documentation
ahci: st: Update the DT example for how to obtain the PHY.
sata_dwc_460ex: indent an if statement
libata: Add tracepoints
libata-eh: Set 'information' field for autosense
libata: Implement support for sense data reporting
libata: Implement NCQ autosense
libata: use status bit definitions in ata_dump_status()
ide,ata: Rename ATA_IDX to ATA_SENSE
libata: whitespace fixes in ata_to_sense_error()
libata: whitespace cleanup in ata_get_cmd_descript()
libata: use READ_LOG_DMA_EXT
libata: remove ATA_FLAG_LOWTAG
sata_dwc_460ex: re-use hsdev->dev instead of dwc_dev
sata_dwc_460ex: move to generic DMA driver
sata_dwc_460ex: join messages back
sata: xgene: add ACPI support for APM X-Gene SATA ports
ata: sata_mv: add proper definitions for LP_PHY_CTL register values
sata_sil24 for some reason pukes when tags are allocated round-robin
which helps tag ordered controllers. To work around the issue,
72dd299d50 ("libata: allow sata_sil24 to opt-out of tag ordered
submission") introduced ATA_FLAG_LOWTAG which tells libata tag
allocation to do lowest-first.
However, with the recent switch to blk-mq tag allocation, the liata
tag allocation code path is no longer used and the workaround is now
implemented in the block layer and selected by setting
scsi_host_template->tag_alloc_policy to BLK_TAG_ALLOC_FIFO. See
9269e23496 ("libata: make sata_sil24 use fifo tag allocator").
This leaves ATA_FLAG_LOWTAG withoout any actual user. Remove it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Shaohua Li <shli@fb.com>
Cc: Dan Williams <dan.j.williams@intel.com>
SAS controller has its own tag allocation, which doesn't directly match to ATA
tag, so SAS and SATA have different code path for ata tags. Originally we use
port->scsi_host (98bd4be1) to destinguish SAS controller, but libsas set
->scsi_host too, so we can't use it for the destinguish, we add a new flag for
this purpose.
Without this patch, the following oops can happen because scsi-mq uses
a host-wide tag map shared among all devices with some integer tag
values >= ATA_MAX_QUEUE. These unexpectedly high tag values cause
__ata_qc_from_tag() to return NULL, which is then dereferenced in
ata_qc_new_init().
BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
IP: [<ffffffff804fd46e>] ata_qc_new_init+0x3e/0x120
PGD 32adf0067 PUD 32adf1067 PMD 0
Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi igb
i2c_algo_bit ptp pps_core pm80xx libsas scsi_transport_sas sg coretemp
eeprom w83795 i2c_i801
CPU: 4 PID: 1450 Comm: cydiskbench Not tainted 4.0.0-rc3 #1
Hardware name: Supermicro X8DTH-i/6/iF/6F/X8DTH, BIOS 2.1b 05/04/12
task: ffff8800ba86d500 ti: ffff88032a064000 task.ti: ffff88032a064000
RIP: 0010:[<ffffffff804fd46e>] [<ffffffff804fd46e>] ata_qc_new_init+0x3e/0x120
RSP: 0018:ffff88032a067858 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff8800ba0d2230 RCX: 000000000000002a
RDX: ffffffff80505ae0 RSI: 0000000000000020 RDI: ffff8800ba0d2230
RBP: ffff88032a067868 R08: 0000000000000201 R09: 0000000000000001
R10: 0000000000000000 R11: 0000000000000000 R12: ffff8800ba0d0000
R13: ffff8800ba0d2230 R14: ffffffff80505ae0 R15: ffff8800ba0d0000
FS: 0000000041223950(0063) GS:ffff88033e480000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000000058 CR3: 000000032a0a3000 CR4: 00000000000006e0
Stack:
ffff880329eee758 ffff880329eee758 ffff88032a0678a8 ffffffff80502dad
ffff8800ba167978 ffff880329eee758 ffff88032bf9c520 ffff8800ba167978
ffff88032bf9c520 ffff88032bf9a290 ffff88032a0678b8 ffffffff80506909
Call Trace:
[<ffffffff80502dad>] ata_scsi_translate+0x3d/0x1b0
[<ffffffff80506909>] ata_sas_queuecmd+0x149/0x2a0
[<ffffffffa0046650>] sas_queuecommand+0xa0/0x1f0 [libsas]
[<ffffffff804ea544>] scsi_dispatch_cmd+0xd4/0x1a0
[<ffffffff804eb50f>] scsi_queue_rq+0x66f/0x7f0
[<ffffffff803e5098>] __blk_mq_run_hw_queue+0x208/0x3f0
[<ffffffff803e54b8>] blk_mq_run_hw_queue+0x88/0xc0
[<ffffffff803e5c74>] blk_mq_insert_request+0xc4/0x130
[<ffffffff803e0b63>] blk_execute_rq_nowait+0x73/0x160
[<ffffffffa0023fca>] sg_common_write+0x3da/0x720 [sg]
[<ffffffffa0025100>] sg_new_write+0x250/0x360 [sg]
[<ffffffffa0025feb>] sg_write+0x13b/0x450 [sg]
[<ffffffff8032ec91>] vfs_write+0xd1/0x1b0
[<ffffffff8032ee54>] SyS_write+0x54/0xc0
[<ffffffff80689932>] system_call_fastpath+0x12/0x17
tj: updated description.
Fixes: 12cb5ce101 ("libata: use blk taging")
Reported-and-tested-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull block driver changes from Jens Axboe:
"This contains:
- The 4k/partition fixes for brd from Boaz/Matthew.
- A few xen front/back block fixes from David Vrabel and Roger Pau
Monne.
- Floppy changes from Takashi, cleaning the device file creation.
- Switching libata to use the new blk-mq tagging policy, removing
code (and a suboptimal implementation) from libata. This will
throw you a merge conflict, since a bug in the original libata
tagging code was fixed since this code was branched. Trivial.
From Shaohua.
- Conversion of loop to blk-mq, from Ming Lei.
- Cleanup of the io_schedule() handling in bsg from Peter Zijlstra.
He claims it improves on unreadable code, which will cost him a
beer.
- Maintainer update or NDB, now handled by Markus Pargmann.
- NVMe:
- Optimization from me that avoids a kmalloc/kfree per IO for
smaller (<= 8KB) IO. This cuts about 1% of high IOPS CPU
overhead.
- Removal of (now) dead RCU code, a relic from before NVMe was
converted to blk-mq"
* 'for-3.20/drivers' of git://git.kernel.dk/linux-block:
xen-blkback: default to X86_32 ABI on x86
xen-blkfront: fix accounting of reqs when migrating
xen-blkback,xen-blkfront: add myself as maintainer
block: Simplify bsg complete all
floppy: Avoid manual call of device_create_file()
NVMe: avoid kmalloc/kfree for smaller IO
MAINTAINERS: Update NBD maintainer
libata: make sata_sil24 use fifo tag allocator
libata: move sas ata tag allocation to libata-scsi.c
libata: use blk taging
NVMe: within nvme_free_queues(), delete RCU sychro/deferred free
null_blk: suppress invalid partition info
brd: Request from fdisk 4k alignment
brd: Fix all partitions BUGs
axonram: Fix bug in direct_access
loop: add blk-mq.h include
block: loop: don't handle REQ_FUA explicitly
block: loop: introduce lo_discard() and lo_req_flush()
block: loop: say goodby to bio
block: loop: improve performance via blk-mq
09c32aaa36 ("ahci_xgene: Fix the dma state machine lockup for the
ATA_CMD_SMART PIO mode command.") missed 3.19 release. Fold it into
for-3.20.
Signed-off-by: Tejun Heo <tj@kernel.org>
The owner module reference of the ahci platform's scsi_host is
initialized to libahci_platform's one, because these drivers use a
scsi_host_template defined in libahci_platform. So these drivers can
be unloaded even if the scsi device is being accessed.
This fixes it by pushing the scsi_host_template from libahci_platform
to all leaf drivers. The scsi_host_template is passed through a new
argument of ahci_platform_init_host().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: linux-ide@vger.kernel.org
Cc: linux-scsi@vger.kernel.org
libata uses its own tag management which is duplication and the
implementation is poor. And if we switch to blk-mq, tag is build-in.
It's time to switch to generic taging.
The SAS driver has its own tag management, and looks we can't directly
map the host controler tag to SATA tag. So I just bypassed the SAS case.
I changed the code/variable name for the tag management of libata to
make it self contained. Only sas will use it. Later if libsas implements
its tag management, the tag management code in libata can be deleted
easily.
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Shaohua Li <shli@fb.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Ronny reports: https://bugzilla.kernel.org/show_bug.cgi?id=87101
"Since commit 8a4aeec8d "libata/ahci: accommodate tag ordered
controllers" the access to the harddisk on the first SATA-port is
failing on its first access. The access to the harddisk on the
second port is working normal.
When reverting the above commit, access to both harddisks is working
fine again."
Maintain tag ordered submission as the default, but allow sata_sil24 to
continue with the old behavior.
Cc: <stable@vger.kernel.org>
Cc: Tejun Heo <tj@kernel.org>
Reported-by: Ronny Hegewald <Ronny.Hegewald@online.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As defined, the DRAT (Deterministic Read After Trim) and RZAT (Return
Zero After Trim) flags in the ATA Command Set are unreliable in the
sense that they only define what happens if the device successfully
executed the DSM TRIM command. TRIM is only advisory, however, and the
device is free to silently ignore all or parts of the request.
In practice this renders the DRAT and RZAT flags completely useless and
because the results are unpredictable we decided to disable discard in
MD for 3.18 to avoid the risk of data corruption.
Hardware vendors in the real world obviously need better guarantees than
what the standards bodies provide. Unfortuntely those guarantees are
encoded in product requirements documents rather than somewhere we can
key off of them programatically. So we are compelled to disabling
discard_zeroes_data for all devices unless we explicitly have data to
support whitelisting them.
This patch whitelists SSDs from a few of the main vendors. None of the
whitelists are based on written guarantees. They are purely based on
empirical evidence collected from internal and external users that have
tested or qualified these drives in RAID deployments.
The whitelist is only meant as a starting point and is by no means
comprehensive:
- All intel SSD models except for 510
- Micron M5?0/M600
- Samsung SSDs
- Seagate SSDs
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata changes from Tejun Heo:
"The only interesting piece is the support for shingled drives. The
changes in libata layer are minimal. All it does is identifying the
new class of device and report upwards accordingly"
* 'for-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Remove FIXME comment in atapi_request_sense()
sata_rcar: Document deprecated "renesas,rcar-sata"
sata_rcar: Add clocks to sata_rcar bindings
ahci_sunxi: Make AHCI_HFLAG_NO_PMP flag configurable with a module option
libata-scsi: Update SATL for ZAC drives
libata: Implement ATA_DEV_ZAC
libsas: use ata_dev_classify()
Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Add new ATA device type for ZAC devices.
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
The return value is not used by callers of these functions nor
by uses of all macros so change the functions to return void.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The AHCI spec allows implementations to issue commands in tag order
rather than FIFO order:
5.3.2.12 P:SelectCmd
HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1)
or HBA selects the command to issue that has had the
PxCI bit set to '1' longer than any other command
pending to be issued.
The result is that commands posted sequentially (time-wise) may play out
of sequence when issued by hardware.
This behavior has likely been hidden by drives that arrange for commands
to complete in issue order. However, it appears recent drives (two from
different vendors that we have found so far) inflict out-of-order
completions as a matter of course. So, we need to take care to maintain
ordered submission, otherwise we risk triggering a drive to fall out of
sequential-io automation and back to random-io processing, which incurs
large latency and degrades throughput.
This issue was found in simple benchmarks where QD=2 seq-write
performance was 30-50% *greater* than QD=32 seq-write performance.
Tagging for -stable and making the change globally since it has a low
risk-to-reward ratio. Also, word is that recent versions of an unnamed
OS also does it this way now. So, drives in the field are already
experienced with this tag ordering scheme.
Cc: <stable@vger.kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ed Ciechanowski <ed.ciechanowski@intel.com>
Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit bc6e7c4b0d "libata, libsas: kill pm_result and related cleanup"
renamed ata_sas_port_async_resume() to ata_sas_port_resume(), but missed
a CONFIG_PM=n stub conversion. Randy fixed that up in commit
a5a6569959 "libata.h: add stub for ata_sas_port_resume", but missed
the deletion of the now unused ata_sas_port_async_resume() routine.
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Fix build error when CONFIG_PM is not enabled by adding a stub
function in <linux/libata.h>.
drivers/scsi/libsas/sas_ata.c: In function 'sas_resume_sata':
drivers/scsi/libsas/sas_ata.c:756:3: error: implicit declaration of function 'ata_sas_port_resume' [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Tejun says:
"At least for libata, worrying about suspend/resume failures don't make
whole lot of sense. If suspend failed, just proceed with suspend. If
the device can't be woken up afterwards, that's that. There isn't
anything we could have done differently anyway. The same for resume, if
spinup fails, the device is dud and the following commands will invoke
EH actions and will eventually fail. Again, there really isn't any
*choice* to make. Just making sure the errors are handled gracefully
(ie. don't crash) and the following commands are handled correctly
should be enough."
The only libata user that actually cares about the result from a suspend
operation is libsas. However, it only cares about whether queuing a new
operation collides with an in-flight one. All libsas does with the
error is retry, but we can just let libata wait for the previous
operation before continuing.
Other cleanups include:
1/ Unifying all ata port pm operations on an ata_port_pm_ prefix
2/ Marking all ata port pm helper routines as returning void, only
ata_port_pm_ entry points need to fake a 0 return value.
3/ Killing ata_port_{suspend|resume}_common() in favor of calling
ata_port_request_pm() directly
4/ Killing the wrappers that just do a to_ata_port() conversion
5/ Clearly marking the entry points that do async operations with an
_async suffix.
Reference: http://marc.info/?l=linux-scsi&m=138995409532286&w=2
Cc: Phillip Susi <psusi@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Todd Brandt <todd.e.brandt@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For some reason, some early WD drives spin up and down drives
erratically when the link is put into slumber mode which can reduce
the life expectancy of the device significantly. Unfortunately, we
don't have full list of devices and given the nature of the issue it'd
be better to err on the side of false positives than the other way
around. Let's disable LPM on all WD devices which match one of the
known problematic model prefixes and are SATA-I.
As horkage list doesn't support matching SATA capabilities, this is
implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is
set for the known prefixes and sets the latter if the matched device
is SATA-I.
Note that this isn't optimal as this disables all LPM operations and
partial link power state reportedly works fine on these; however, the
way LPM is implemented in libata makes it difficult to precisely map
libata LPM setting to specific link power state. Well, these devices
are already fairly outdated. Let's just disable whole LPM for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com>
Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=57211
Cc: stable@vger.kernel.org
Certain drives cannot handle queued TRIM commands properly, even
though support is indicated in the IDENTIFY DEVICE buffer. This patch
allows for disabling the commands for the affected drives and apply it
to the Micron/Crucial M500 SSDs which exhibit incorrect protocol
behavior when issued queued TRIM commands, which could lead to silent
data corruption.
tj: Merged two unnecessarily split patches and made minor edits
including shortening horkage name.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Link: http://lkml.kernel.org/g/1387246554-7311-1-git-send-email-marc.ceeeee@gmail.com
Cc: stable@vger.kernel.org # 3.12+
Some new SSDs support the queued version of the DSM TRIM command.
Let the driver use the new command if supported.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support for the following ATA opcodes, which are present
in SATA 3.1 and T13 ATA ACS-3:
SEND FPDMA QUEUED
RECEIVE FPDMA QUEUED
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a new port flag, ATA_FLAG_FPDMA_AUX, used to indicate
support for transmission of the H2D FIS 'auxiliary' field.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
SATA 3.1 added an "auxiliary" field to the host-to-device FIS.
Populate the host-to-device FIS with the new field via the
taskfile struct.
Signed-off-by: Marc Carino <marc.ceeeee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Binding ACPI handle to SCSI device has several drawbacks, namely:
1 During ATA device initialization time, ACPI handle will be needed
while SCSI devices are not created yet. So each time ACPI handle is
needed, instead of retrieving the handle by ACPI_HANDLE macro,
a namespace scan is performed to find the handle for the corresponding
ATA device. This is inefficient, and also expose a restriction on
calling path not holding any lock.
2 The binding to SCSI device tree makes code complex, while at the same
time doesn't bring us any benefit. All ACPI handlings are still done
in ATA module, not in SCSI.
Rework the ATA ACPI binding code to bind ACPI handle to ATA transport
devices(ATA port and ATA device). The binding needs to be done only once,
since the ATA transport devices do not go away with hotplug. And due to
this, the flush_work call in hotplug handler for ATA bay is no longer
needed.
Tested on an Intel test platform for binding and runtime power off for
ODD(ZPODD) and hard disk; on an ASUS S400C for binding and normal boot
and S3, where its SATA port node has _SDD and _GTF control methods when
configured as an AHCI controller and its PATA device node has _GTF
control method when configured as an IDE controller. SATA PMP binding
and ATA hotplug is not tested.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Move 'struct ata_taskfile', ata_prot_flags() and their friends from
<linux/ata.h> to <linux/libata.h>. They were misplaced from the beginning, as
<linux/ata.h> should cover ATA/ATAPI and related standards only -- to which the
aforementioned structure and function have only remote relation.
I would have moved 'enum ata_tf_protocols' closely related to 'struct
ata_taskfile' but it unfortunately gets used by 'drivers/ide/ide-ioctls.c'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Create a new ata_port_operations function pointer called
transmit_led_message and give it the default value of
ahci_transmit_led_message. This allows AHCI controllers with
non-standard LED interfaces to use the existing em_ interface.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some device require DMADIR to be enabled, but are not detected as such
by atapi_id_dmadir. One such example is "Asus Serillel 2"
SATA-host-to-PATA-device bridge: the bridge itself requires DMADIR,
even if the bridged device does not.
As atapi_dmadir module parameter can cause problems with some devices
(as per Tejun Heo's memory), enabling it globally may not be possible
depending on the hardware.
This patch adds atapi_dmadir in the form of a "force" horkage value,
allowing global, per-bus and per-device control.
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
While registering host controller track port number based upon number
of ports available on the controller, export port_no attribute through
/sys. This patch is needed by udev for composing persistent links in
/dev/disk/by-path.
/sys/devices/pci0000:00/0000:00:1f.2/ata8/ata_port/ata8
total 0
lrwxrwxrwx. 1 root root 0 Mar 6 12:43 device -> ../../../ata8
-r--r--r--. 1 root root 4096 Mar 6 12:43 idle_irq
-r--r--r--. 1 root root 4096 Mar 6 12:43 nr_pmp_links
-r--r--r--. 1 root root 4096 Mar 6 12:43 port_no
drwxr-xr-x. 2 root root 0 Mar 6 12:42 power
lrwxrwxrwx. 1 root root 0 Mar 6 12:41 subsystem -> ../../../../../../class/ata_port
-rw-r--r--. 1 root root 4096 Mar 6 12:40 uevent
1
Signed-off-by: David Milburn <dmilburn@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The ODD can be enabled for ZPODD if the following three conditions are
satisfied:
1 The ODD supports device attention;
2 The platform can runtime power off the ODD through ACPI;
3 The ODD is either slot type or drawer type.
For such ODDs, zpodd_init is called and a new structure is allocated for
it to store ZPODD related stuffs.
And the zpodd_dev_enabled function is used to test if ZPODD is currently
enabled for this ODD.
A new config CONFIG_SATA_ZPODD is added to selectively build ZPODD code.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
NCQ capability was used to check availability of SATA Settings page
from Identify Device Data Log, which contains DevSlp timing variables.
It does not work on some HDDs and leads to error messages.
IDENTIFY word 78 bit 5(Hardware Feature Control) can't work either
because it is only the sufficient condition of Identify Device data
log, not the necessary condition.
This patch replaced ata_device->sata_settings with ->devslp_timing
to only save DevSlp timing variables(8 bytes), instead of the whole
SATA Settings page(512 bytes).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=51881
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This relatively simple boiler-plate code is repeated in several platform
drivers. We should implement a common version in libata.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 66fa7f215 "libata-acpi: improve ACPI disabling" introdcued the
behaviour of disabling ATA ACPI if ata_acpi_on_devcfg failed the 2nd
time, but commit 30dcf76ac dropped this behaviour and this caused
problem for Dimitris Damigos, where his laptop can not resume correctly.
The bugzilla page for it is:
https://bugzilla.kernel.org/show_bug.cgi?id=49331
The problem is, ata_dev_push_id will fail the 2nd time it is invoked,
and due to disabling ACPI code is dropped, ata_acpi_on_devcfg which
calls ata_dev_push_id will keep failing and eventually made the device
disabled.
This patch restores the original behaviour, if acpi failed the 2nd time,
disable acpi functionality for the device(and we do not event need to
add a debug message for this as it is still there ;-).
Reported-by: Dimitris Damigos <damigos@freemail.gr>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a large set of updates, mostly for drivers (qla2xxx [including support
for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa, be2iscsi, isci,
lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas). There's also a rework for tape
adding virtually unlimited numbers of tape drives plus a set of dif fixes for
sd and a fix for a live lock on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQaqCFAAoJEDeqqVYsXL0MKJ4IALg/Obnk0/fNvBUNIrh5zRmj
r9UlXFJnlEDT03qRGdn8okgWMChbgaD1ZrwDTQnjNsabVQoTXI6oO6/uL2c8crpY
BFBwJvkNJS99nbcZv10CpJ3K7ykmRnKlkYon12iknhGwdtU+XJ14Z4PUcZkI9jmg
sBQQ6uNVWyosaONNE+k6o+dw6OTttJkzRX8e9in3thstxNTcG+h9iB1zZ/ETkSEj
tD4MyOgDiPf8kPV2awQThQGpni9Tu3SQr5dEn/iUUktUjiYsDNQuyaAk+QzyhUU7
D35iIJnIHlXTSTMQkrG4qpJHBvqPkWlYJzaOmheQryQ3vzp2C5Ly/hS9il45uIQ=
=49u9
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This is a large set of updates, mostly for drivers (qla2xxx [including
support for new 83xx based card], qla4xxx, mpt2sas, bfa, zfcp, hpsa,
be2iscsi, isci, lpfc, ipr, ibmvfc, ibmvscsi, megaraid_sas).
There's also a rework for tape adding virtually unlimited numbers of
tape drives plus a set of dif fixes for sd and a fix for a live lock
on hot remove of SCSI devices.
This round includes a signed tag pull of isci-for-3.6
Signed-off-by: James Bottomley <JBottomley@Parallels.com>"
Fix up trivial conflict in drivers/scsi/qla2xxx/qla_nx.c due to new PCI
helper function use in a function that was removed by this pull.
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (198 commits)
[SCSI] st: remove st_mutex
[SCSI] sd: Ensure we correctly disable devices with unknown protection type
[SCSI] hpsa: gen8plus Smart Array IDs
[SCSI] qla4xxx: Update driver version to 5.03.00-k1
[SCSI] qla4xxx: Disable generating pause frames for ISP83XX
[SCSI] qla4xxx: Fix double clearing of risc_intr for ISP83XX
[SCSI] qla4xxx: IDC implementation for Loopback
[SCSI] qla4xxx: update copyrights in LICENSE.qla4xxx
[SCSI] qla4xxx: Fix panic while rmmod
[SCSI] qla4xxx: Fail probe_adapter if IRQ allocation fails
[SCSI] qla4xxx: Prevent MSI/MSI-X falling back to INTx for ISP82XX
[SCSI] qla4xxx: Update idc reg in case of PCI AER
[SCSI] qla4xxx: Fix double IDC locking in qla4_8xxx_error_recovery
[SCSI] qla4xxx: Clear interrupt while unloading driver for ISP83XX
[SCSI] qla4xxx: Print correct IDC version
[SCSI] qla4xxx: Added new mbox cmd to pass driver version to FW
[SCSI] scsi_dh_alua: Enable STPG for unavailable ports
[SCSI] scsi_remove_target: fix softlockup regression on hot remove
[SCSI] ibmvscsi: Fix host config length field overflow
[SCSI] ibmvscsi: Remove backend abstraction
...
Device Sleep is a feature as described in AHCI 1.3.1 Technical Proposal.
This feature enables an HBA and SATA storage device to enter the DevSleep
interface state, enabling lower power SATA-based systems.
Aggressive Device Sleep enables the HBA to assert the DEVSLP signal as
soon as there are no commands outstanding to the device and the port
specific Device Sleep idle timer has expired. This enables autonomous
entry into the DevSleep interface state without waiting for software
in power sensitive systems.
This patch enables Aggressive Device Sleep only if both host controller
and device support it.
Tested on AMD reference board together with Device Sleep supported device
sample.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Reviewed-by: Aaron Lu <aaron.lwe@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
