The module code assumes noone will ever ask for a per-cpu area more than
SMP_CACHE_BYTES aligned. However, as these cases show, gcc asks sometimes
asks for 32-byte alignment for the per-cpu section on a module, and if
CONFIG_X86_L1_CACHE_SHIFT is 4, we hit that BUG_ON(). This is obviously an
unusual combination, as there have been few reports, but better to warn
than die.
See:
http://www.ussg.iu.edu/hypermail/linux/kernel/0409.0/0768.html
And more recently:
http://bugs.gentoo.org/show_bug.cgi?id=97006
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes sys_set_zone_reclaim() for now. While i'm sure Martin is
trying to solve a real problem, we must not hard-code an incomplete and
insufficient approach into a syscall, because syscalls are pretty much
for eternity. I am quite strongly convinced that this syscall must not
hit v2.6.13 in its current form.
Firstly, the syscall lacks basic syscall design: e.g. it allows the
global setting of VM policy for unprivileged users. (!) [ Imagine an
Oracle installation and a SAP installation on the same NUMA box fighting
over the 'optimal' setting for this flag. What will they do? Will they
try to set the flag to their own preferred value every second or so? ]
Secondly, it was added based on a single datapoint from Martin:
http://marc.theaimsgroup.com/?l=linux-mm&m=111763597218177&w=2
where Martin characterizes the numbers the following way:
' Run-to-run variability for "make -j" is huge, so these numbers aren't
terribly useful except to see that with reclaim the benchmark still
finishes in a reasonable amount of time. '
in other words: the fundamental problem has likely not been solved, only
a tendential move into the right direction has been observed, and a
handful of numbers were picked out of a set of hugely variable results,
without showing the variability data. How much variance is there
run-to-run?
I'd really suggest to first walk the walk and see what's needed to get
stable & predictable kernel compilation numbers on that NUMA box, before
adding random syscalls to tune a particular aspect of the VM ... which
approach might not even matter once the whole picture has been analyzed
and understood!
The third, most important point is that the syscall exposes VM tuning
internals in a completely unstructured way. What sense does it make to
have a _GLOBAL_ per-node setting for 'should we go to another node for
reclaim'? If then it might make sense to do this per-app, via numalib or
so.
The change is minimalistic in that it doesnt remove the syscall and the
underlying infrastructure changes, only the user-visible changes. We
could perhaps add a CAP_SYS_ADMIN-only sysctl for this hack, a'ka
/proc/sys/vm/swappiness, but even that looks quite counterproductive
when the generic approach is that we are trying to reduce the number of
external factors in the VM balance picture.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This snuck in with an x86_64 change. Thanks to Richard Purdie
<rpurdie@rpsys.net> for spotting it.
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If device_suspend(PMSG_FREEZE) is not ready to be called in
kernel_restart it is definitely not ready to be called in the even more
fickle kernel_kexec.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(We found this (after a customer complained) and it is in the kernel.org
kernel. Seems that for CLOCK_MONOTONIC absolute timers and clock_nanosleep
calls both the request time and wall_to_monotonic are subtracted prior to
the normalize resulting in an overflow in the existing normalize test.
This causes the result to be shifted ~4 seconds ahead instead of ~2 seconds
back in time.)
The normalize code in posix-timers.c fails when the tv_nsec member is ~1.2
seconds negative. This can happen on absolute timers (and
clock_nanosleeps) requested on CLOCK_MONOTONIC (both the request time and
wall_to_monotonic are subtracted resulting in the possibility of a number
close to -2 seconds.)
This fix uses the set_normalized_timespec() (which does not have an
overflow problem) to fix the problem and as a side effect makes the code
cleaner.
Signed-off-by: George Anzinger <george@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This avoids some potential stack overflows with very deep softirq callchains.
i386 does this too.
TOADD CFI annotation
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My fairly ordinary x86 test box gets stuck during reboot on the
wait_for_completion() in ide_do_drive_cmd():
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
`gcc -W' likes to complain if the static keyword is not at the beginning of
the declaration. This patch fixes all remaining occurrences of "inline
static" up with "static inline" in the entire kernel tree (140 occurrences in
47 files).
While making this change I came across a few lines with trailing whitespace
that I also fixed up, I have also added or removed a blank line or two here
and there, but there are no functional changes in the patch.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add kerneldoc to kernel/cpuset.c
Fix cpuset typos in init/Kconfig
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Split spin lock and r/w lock implementation into a single try which is done
inline and an out of line function that repeatedly tries to get the lock
before doing the cpu_relax(). Add a system control to set the number of
retries before a cpu is yielded.
The reason for the spin lock retry is that the diagnose 0x44 that is used to
give up the virtual cpu is quite expensive. For spin locks that are held only
for a short period of time the costs of the diagnoses outweights the savings
for spin locks that are held for a longer timer. The default retry count is
1000.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the recent off-by-one fix in the itimer code:
1. The repeating timer is figured using the requested time
(not +1 as we know where we are in the jiffie).
2. The tests for interval too large are left to the time_val to jiffie code.
Signed-off-by: George Anzinger <george@mvista.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a warning in the disable_nonboot_cpus call in
kernel/power/smp.c.
Signed-off by: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here's the patch again to fix the code to handle if the values between
MAX_USER_RT_PRIO and MAX_RT_PRIO are different.
Without this patch, an SMP system will crash if the values are
different.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
RLIMIT_RTPRIO is supposed to grant non privileged users the right to use
SCHED_FIFO/SCHED_RR scheduling policies with priorites bounded by the
RLIMIT_RTPRIO value via sched_setscheduler(). This is usually used by
audio users.
Unfortunately this is broken in 2.6.13rc3 as you can see in the excerpt
from sched_setscheduler below:
/*
* Allow unprivileged RT tasks to decrease priority:
*/
if (!capable(CAP_SYS_NICE)) {
/* can't change policy */
if (policy != p->policy)
return -EPERM;
After the above unconditional test which causes sched_setscheduler to
fail with no regard to the RLIMIT_RTPRIO value the following check is made:
/* can't increase priority */
if (policy != SCHED_NORMAL &&
param->sched_priority > p->rt_priority &&
param->sched_priority >
p->signal->rlim[RLIMIT_RTPRIO].rlim_cur)
return -EPERM;
Thus I do believe that the RLIMIT_RTPRIO value must be taken into
account for the policy check, especially as the RLIMIT_RTPRIO limit is
of no use without this change.
The attached patch fixes this problem.
Signed-off-by: Andreas Steinmetz <ast@domdv.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The suspend to disk code was a poor copy of the code in
sys_reboot now that we have kernel_power_off, kernel_restart
and kernel_halt use them instead of poorly duplicating them inline.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We know the system is in trouble so there is no question if this
is an emergecy :)
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We already do all of the gymnastics to run from process context
to call the power off code so call into the power off code cleanly.
This especially helps acpi as part of it's shutdown logic should
run acpi_shutdown called from device_shutdown which was not
being called from here.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the kernel is working well and we want to restart cleanly
kernel_restart is the function to use. But in many instances
the kernel wants to reboot when thing are expected to be working
very badly such as from panic or a software watchdog handler.
This patch adds the function emergency_restart() so that
callers can be clear what semantics they expect when calling
restart. emergency_restart() is expected to be callable
from interrupt context and possibly reliable in even more
trying circumstances.
This is an initial generic implementation for all architectures.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is obvious we wanted to call kernel_restart here
but since we don't have it the code was expanded inline and hasn't
been correct since sometime in 2.4.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Because the factors of sys_reboot don't exist people calling
into the reboot path duplicate the code badly, leading to
inconsistent expectations of code in the reboot path.
This patch should is just code motion.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the recent addition of device_suspend calls into
sys_reboot two code paths were missed.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... by generating serial numbers only if an audit context is actually
_used_, rather than doing so at syscall entry even when the context
isn't necessarily marked auditable.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we flush a pending syscall audit record due to audit_free(), we
might be doing that in the context of the idle thread. So use GFP_ATOMIC
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix the sparse warning "implicit cast to nocast type"
Signed-off-by: Victor Fusco <victor@cetuc.puc-rio.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This moves the inotify sysctl knobs to "/proc/sys/fs/inotify" from
"/proc/sys/fs". Also some related cleanup.
Signed-off-by: Robert Love <rml@novell.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
inotify is intended to correct the deficiencies of dnotify, particularly
its inability to scale and its terrible user interface:
* dnotify requires the opening of one fd per each directory
that you intend to watch. This quickly results in too many
open files and pins removable media, preventing unmount.
* dnotify is directory-based. You only learn about changes to
directories. Sure, a change to a file in a directory affects
the directory, but you are then forced to keep a cache of
stat structures.
* dnotify's interface to user-space is awful. Signals?
inotify provides a more usable, simple, powerful solution to file change
notification:
* inotify's interface is a system call that returns a fd, not SIGIO.
You get a single fd, which is select()-able.
* inotify has an event that says "the filesystem that the item
you were watching is on was unmounted."
* inotify can watch directories or files.
Inotify is currently used by Beagle (a desktop search infrastructure),
Gamin (a FAM replacement), and other projects.
See Documentation/filesystems/inotify.txt.
Signed-off-by: Robert Love <rml@novell.com>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
dup_mmap of a VM_DONTCOPY vma forgot to lower the child's total_vm. (But
no way does this account for the recent report of total_vm seen too low.)
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kernel/power/disk.c needs a declaration of name_to_dev_t() in scope. mount.h
seems like an appropriate choice.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Free some RAM before entering S3 so that upon
resume we can be sure early allocations will succeed.
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Register an "acpi" system device to be notified of shutdown preparation.
This depends on CONFIG_PM
http://bugzilla.kernel.org/show_bug.cgi?id=4041
Signed-off-by: Alexey Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The BKS might be reacquired before we have dropped PREEMPT_ACTIVE, which
could trigger a second could trigger a second cond_resched() call. Bug
found by Hirofumi Ogawa.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new section called ".data.read_mostly" for data items that are read
frequently and rarely written to like cpumaps etc.
If these maps are placed in the .data section then these frequenly read
items may end up in cachelines with data is is frequently updated. In that
case all processors in an SMP system must needlessly reload the cachelines
again and again containing elements of those frequently used variables.
The ability to share these cachelines will allow each cpu in an SMP system
to keep local copies of those shared cachelines thereby optimizing
performance.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Shobhit Dayal <shobhit@calsoftinc.com>
Signed-off-by: Christoph Lameter <christoph@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
freezeable() already tests for TRACED/STOPPED processes, no need to do it
twice.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix error handling and whitespace in swsusp.c. swsusp_free() was called when
there was nothing allocating, leading to oops.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move device name resolution code around so that it is not called from
resume-from-initrd. name_to_dev_t may be unavailable at that point.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following renames arch_init, a kprobes function for performing any
architecture specific initialization, to arch_init_kprobes in order to
cleanup the namespace.
Also, this patch adds arch_init_kprobes to sparc64 to fix the sparc64 kprobes
build from the last return probe patch.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pid in the audit context isn't always set up. Use tsk->pid when
checking whether it's auditd in audit_filter_syscall(), instead of
ctx->pid. Remove a band-aid which did the same elsewhere.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We force a rate-limit on auditable events by making them wait for space
on the backlog queue. However, if auditd really is AWOL then this could
potentially bring the entire system to a halt, depending on the audit
rules in effect.
Firstly, make sure the wait time is honoured correctly -- it's the
maximum time the process should wait, rather than the time to wait
_each_ time round the loop. We were getting re-woken _each_ time a
packet was dequeued, and the timeout was being restarted each time.
Secondly, reset the wait time after audit_panic() is called. In general
this will be reset to zero, to allow progress to be made. If the system
is configured to _actually_ panic on audit_panic() then that will
already have happened; otherwise we know that audit records are being
lost anyway.
These two tunables can't be exposed via AUDIT_GET and AUDIT_SET because
those aren't particularly well-designed. It probably should have been
done by sysctls or sysfs anyway -- one for a later patch.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Anyone reporting a stuck IRQ should try these options. Its effectiveness
varies we've found in the Fedora case. Quite a few systems with misdescribed
IRQ routing just work when you use irqpoll. It also fixes up the VIA systems
although thats now fixed with the VIA quirk (which we could just make default
as its what Redmond OS does but Linus didn't like it historically).
A small number of systems have jammed IRQ sources or misdescribes that cause
an IRQ that we have no handler registered anywhere for. In those cases it
doesn't help.
Signed-off-by: Alan Cox <number6@the-village.bc.nu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As Steven Rostedt pointed out, there are 2 problems with ITIMER_REAL
timers.
1. do_setitimer() does not call del_timer_sync() in case
when the timer is not pending (it_real_value() returns 0).
This is wrong, the timer may still be running, and it can
rearm itself.
2. It calls del_timer_sync() with tsk->sighand->siglock held.
This is deadlockable, because timer's handler needs this
lock too.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use msleep() in a few places.
Signed-off-by: Luca Falavigna <dktrkranz@gmail.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch tweaks idle thread setup semantics a bit: instead of setting
NEED_RESCHED in init_idle(), we do an explicit schedule() before calling
into cpu_idle().
This patch, while having no negative side-effects, enables wider use of
cond_resched()s. (which might happen in the stock kernel too, but it's
particulary important for voluntary-preempt)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following is the second version of the function return probe patches
I sent out earlier this week. Changes since my last submission include:
* Fix in ppc64 code removing an unneeded call to re-enable preemption
* Fix a build problem in ia64 when kprobes was turned off
* Added another BUG_ON check to each of the architecture trampoline
handlers
My initial patch description ==>
From my experiences with adding return probes to x86_64 and ia64, and the
feedback on LKML to those patches, I think we can simplify the design
for return probes.
The following patch tweaks the original design such that:
* Instead of storing the stack address in the return probe instance, the
task pointer is stored. This gives us all we need in order to:
- find the correct return probe instance when we enter the trampoline
(even if we are recursing)
- find all left-over return probe instances when the task is going away
This has the side effect of simplifying the implementation since more
work can be done in kernel/kprobes.c since architecture specific knowledge
of the stack layout is no longer required. Specifically, we no longer have:
- arch_get_kprobe_task()
- arch_kprobe_flush_task()
- get_rp_inst_tsk()
- get_rp_inst()
- trampoline_post_handler() <see next bullet>
* Instead of splitting the return probe handling and cleanup logic across
the pre and post trampoline handlers, all the work is pushed into the
pre function (trampoline_probe_handler), and then we skip single stepping
the original function. In this case the original instruction to be single
stepped was just a NOP, and we can do without the extra interruption.
The new flow of events to having a return probe handler execute when a target
function exits is:
* At system initialization time, a kprobe is inserted at the beginning of
kretprobe_trampoline. kernel/kprobes.c use to handle this on it's own,
but ia64 needed to do this a little differently (i.e. a function pointer
is really a pointer to a structure containing the instruction pointer and
a global pointer), so I added the notion of arch_init(), so that
kernel/kprobes.c:init_kprobes() now allows architecture specific
initialization by calling arch_init() before exiting. Each architecture
now registers a kprobe on it's own trampoline function.
* register_kretprobe() will insert a kprobe at the beginning of the targeted
function with the kprobe pre_handler set to arch_prepare_kretprobe
(still no change)
* When the target function is entered, the kprobe is fired, calling
arch_prepare_kretprobe (still no change)
* In arch_prepare_kretprobe() we try to get a free instance and if one is
available then we fill out the instance with a pointer to the return probe,
the original return address, and a pointer to the task structure (instead
of the stack address.) Just like before we change the return address
to the trampoline function and mark the instance as used.
If multiple return probes are registered for a given target function,
then arch_prepare_kretprobe() will get called multiple times for the same
task (since our kprobe implementation is able to handle multiple kprobes
at the same address.) Past the first call to arch_prepare_kretprobe,
we end up with the original address stored in the return probe instance
pointing to our trampoline function. (This is a significant difference
from the original arch_prepare_kretprobe design.)
* Target function executes like normal and then returns to kretprobe_trampoline.
* kprobe inserted on the first instruction of kretprobe_trampoline is fired
and calls trampoline_probe_handler() (no change here)
* trampoline_probe_handler() consumes each of the instances associated with
the current task by calling the registered handler function and marking
the instance as unused until an instance is found that has a return address
different then the trampoline function.
(change similar to my previous ia64 RFC)
* If the task is killed with some left-over return probe instances (meaning
that a target function was entered, but never returned), then we just
free any instances associated with the task. (Not much different other
then we can handle this without calling architecture specific functions.)
There is a known problem that this patch does not yet solve where
registering a return probe flush_old_exec or flush_thread will put us
in a bad state. Most likely the best way to handle this is to not allow
registering return probes on these two functions.
(Significant change)
This patch series applies to the 2.6.12-rc6-mm1 kernel, and provides:
* kernel/kprobes.c changes
* i386 patch of existing return probes implementation
* x86_64 patch of existing return probe implementation
* ia64 implementation
* ppc64 implementation (provided by Ananth)
This patch implements the architecture independant changes for a reworking
of the kprobes based function return probes design. Changes include:
* Removing functions for querying a return probe instance off a stack address
* Removing the stack_addr field from the kretprobe_instance definition,
and adding a task pointer
* Adding architecture specific initialization via arch_init()
* Removing extern definitions for the architecture trampoline functions
(this isn't needed anymore since the architecture handles the
initialization of the kprobe in the return probe trampoline function.)
Signed-off-by: Rusty Lynch <rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that PPC64 has no-execute support, here is a second try to fix the
single step out of line during kprobe execution. Kprobes on x86_64 already
solved this problem by allocating an executable page and using it as the
scratch area for stepping out of line. Reuse that.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the CFQ io scheduler to the new time sliced design (cfq
v3). It provides full process fairness, while giving excellent
aggregate system throughput even for many competing processes. It
supports io priorities, either inherited from the cpu nice value or set
directly with the ioprio_get/set syscalls. The latter closely mimic
set/getpriority.
This import is based on my latest from -mm.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. Establish a simple API for process freezing defined in linux/include/sched.h:
frozen(process) Check for frozen process
freezing(process) Check if a process is being frozen
freeze(process) Tell a process to freeze (go to refrigerator)
thaw_process(process) Restart process
frozen_process(process) Process is frozen now
2. Remove all references to PF_FREEZE and PF_FROZEN from all
kernel sources except sched.h
3. Fix numerous locations where try_to_freeze is manually done by a driver
4. Remove the argument that is no longer necessary from two function calls.
5. Some whitespace cleanup
6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
cleared before setting PF_FROZEN, recalc_sigpending does not check
PF_FROZEN).
This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes use of ALIGN() to remove duplicate round-up code.
Signed-off-by: Nick Wilson <njw@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment for msleep_interruptible() is wrong, as it will ignore
wait-queue events, but will wake up early for signals.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch provides purely cosmetic changes and corrects CodingStyle
guide lines related certain issues like below in kexec related files
o braces for one line "if" statements, "for" loops,
o more than 80 column wide lines,
o No space after "while", "for" and "switch" key words
o Changes:
o take-2: Removed the extra tab before "case" key words.
o take-3: Put operator at the end of line and space before "*/"
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Makes kexec_crashdump() take a pt_regs * as an argument. This allows to
get exact register state at the point of the crash. If we come from direct
panic assertion NULL will be passed and the current registers saved before
crashdump.
This hooks into two places:
die(): check the conditions under which we will panic when calling
do_exit and go there directly with the pt_regs that caused the fatal
fault.
die_nmi(): If we receive an NMI lockup while in the kernel use the
pt_regs and go directly to crash_kexec(). We're probably nested up badly
at this point so this might be the only chance to escape with proper
information.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Vivek Goyal" <vgoyal@in.ibm.com>
o Support for /proc/vmcore interface. This interface exports elf core image
either in ELF32 or ELF64 format, depending on the format in which elf headers
have been stored by crashed kernel.
o Added support for CONFIG_VMCORE config option.
o Removed the dependency on /proc/kcore.
From: "Eric W. Biederman" <ebiederm@xmission.com>
This patch has been refactored to more closely match the prevailing style in
the affected files. And to clearly indicate the dependency between
/proc/kcore and proc/vmcore.c
From: Hariprasad Nellitheertha <hari@in.ibm.com>
This patch contains the code that provides an ELF format interface to the
previous kernel's memory post kexec reboot.
Signed off by Hariprasad Nellitheertha <hari@in.ibm.com>
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for retrieving the address of elf core header if one
is passed in command line.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch provides the interfaces necessary to read the dump contents,
treating it as a high memory device.
Signed off by Hariprasad Nellitheertha <hari@in.ibm.com>
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch exports kexec global variable "crash_notes" to user space
through sysfs as kernel attribute in /sys/kernel.
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a minor bug fix in kexec to resolve the problem of loading panic
kernel with initrd.
o Problem: Loading a capture kenrel fails if initrd is also being loaded.
This has been observed for vmlinux image for kexec on panic case.
o This patch fixes the problem. In segment location and size verification
logic, minor correction has been done. Segment memory end (mend) should be
mstart + memsz - 1. This one byte offset was source of failure for initrd
loading which was being loaded at hole boundary.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces the architecture independent implementation the
sys_kexec_load, the compat_sys_kexec_load system calls.
Kexec on panic support has been integrated into the core patch and is
relatively clean.
In addition the hopefully architecture independent option
crashkernel=size@location has been docuemented. It's purpose is to reserve
space for the panic kernel to live, and where no DMA transfer will ever be
setup to access.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a new preemption model: 'Voluntary Kernel Preemption'. The
3 models can be selected from a new menu:
(X) No Forced Preemption (Server)
( ) Voluntary Kernel Preemption (Desktop)
( ) Preemptible Kernel (Low-Latency Desktop)
we still default to the stock (Server) preemption model.
Voluntary preemption works by adding a cond_resched()
(reschedule-if-needed) call to every might_sleep() check. It is lighter
than CONFIG_PREEMPT - at the cost of not having as tight latencies. It
represents a different latency/complexity/overhead tradeoff.
It has no runtime impact at all if disabled. Here are size stats that show
how the various preemption models impact the kernel's size:
text data bss dec hex filename
3618774 547184 179896 4345854 424ffe vmlinux.stock
3626406 547184 179896 4353486 426dce vmlinux.voluntary +0.2%
3748414 548640 179896 4476950 445016 vmlinux.preempt +3.5%
voluntary-preempt is +0.2% of .text, preempt is +3.5%.
This feature has been tested for many months by lots of people (and it's
also included in the RHEL4 distribution and earlier variants were in Fedora
as well), and it's intended for users and distributions who dont want to
use full-blown CONFIG_PREEMPT for one reason or another.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only sane way to clean up the current 3 lock_kernel() variants seems to
be to remove the spinlock-based BKL implementations altogether, and to keep
the semaphore-based one only. If we dont want to do that for whatever
reason then i'm afraid we have to live with the current complexity. (but
i'm open for other cleanup suggestions as well.)
To explore this possibility we'll (at a minimum) have to know whether the
semaphore-based BKL works fine on plain SMP too. The patch below enables
this.
The patch may make sense in isolation as well, as it might bring
performance benefits: code that would formerly spin on the BKL spinlock
will now schedule away and give up the CPU. It might introduce performance
regressions as well, if any performance-critical code uses the BKL heavily
and gets overscheduled due to the semaphore. I very much hope there is no
such performance-critical codepath left though.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch consolidates the CONFIG_PREEMPT and CONFIG_PREEMPT_BKL
preemption options into kernel/Kconfig.preempt. This, besides reducing
source-code, also enables more centralized tweaking of preemption related
options.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adds the core update_cpu_domains code and updated cpusets documentation
Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Acked-by: Paul Jackson <pj@sgi.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patches add dynamic sched domains functionality that was
extensively discussed on lkml and lse-tech. I would like to see this added to
-mm
o The main advantage with this feature is that it ensures that the scheduler
load balacing code only balances against the cpus that are in the sched
domain as defined by an exclusive cpuset and not all of the cpus in the
system. This removes any overhead due to load balancing code trying to
pull tasks outside of the cpu exclusive cpuset only to be prevented by
the tasks' cpus_allowed mask.
o cpu exclusive cpusets are useful for servers running orthogonal
workloads such as RT applications requiring low latency and HPC
applications that are throughput sensitive
o It provides a new API partition_sched_domains in sched.c
that makes dynamic sched domains possible.
o cpu_exclusive cpusets sets are now associated with a sched domain.
Which means that the users can dynamically modify the sched domains
through the cpuset file system interface
o ia64 sched domain code has been updated to support this feature as well
o Currently, this does not support hotplug. (However some of my tests
indicate hotplug+preempt is currently broken)
o I have tested it extensively on x86.
o This should have very minimal impact on performance as none of
the fast paths are affected
Signed-off-by: Dinakar Guniguntala <dino@in.ibm.com>
Acked-by: Paul Jackson <pj@sgi.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Presently, a process without the capability CAP_SYS_NICE can not change
its own policy, which is OK.
But it can also not decrease its RT priority (if scheduled with policy
SCHED_RR or SCHED_FIFO), which is what this patch changes.
The rationale is the same as for the nice value: a process should be
able to require less priority for itself. Increasing the priority is
still not allowed.
This is for example useful if you give a multithreaded user process a RT
priority, and the process would like to organize its internal threads
using priorities also. Then you can give the process the highest
priority needed N, and the process starts its threads with lower
priorities: N-1, N-2...
The POSIX norm says that the permissions are implementation specific, so
I think we can do that.
In a sense, it makes the permissions consistent whatever the policy is:
with this patch, process scheduled by SCHED_FIFO, SCHED_RR and
SCHED_OTHER can all decrease their priority.
From: Ingo Molnar <mingo@elte.hu>
cleaned up and merged to -mm.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The maximum rebalance interval allowed by the multiprocessor balancing
backoff is often not large enough to handle corner cases where there are
lots of tasks pinned on a CPU. Suresh reported:
I see system livelock's if for example I have 7000 processes
pinned onto one cpu (this is on the fastest 8-way system I
have access to).
After this patch, the machine is reported to go well above this number.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Consolidate balance-on-exec with balance-on-fork. This is made easy by the
sched-domains RCU patches.
As well as the general goodness of code reduction, this allows the runqueues
to be unlocked during balance-on-fork.
schedstats is a problem. Maybe just have balance-on-event instead of
distinguishing fork and exec?
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One of the problems with the multilevel balance-on-fork/exec is that it needs
to jump through hoops to satisfy sched-domain's locking semantics (that is,
you may traverse your own domain when not preemptable, and you may traverse
others' domains when holding their runqueue lock).
balance-on-exec had to potentially migrate between more than one CPU before
finding a final CPU to migrate to, and balance-on-fork needed to potentially
take multiple runqueue locks.
So bite the bullet and make sched-domains go completely RCU. This actually
simplifies the code quite a bit.
From: Ingo Molnar <mingo@elte.hu>
schedstats RCU fix, and a nice comment on for_each_domain, from Ingo.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The fundamental problem that Suresh has with balance on exec and fork is that
it only tries to balance the top level domain with the flag set.
This was worked around by removing degenerate domains, but is still a problem
if people want to start using more complex sched-domains, especially
multilevel NUMA that ia64 is already using.
This patch makes balance on fork and exec try balancing over not just the top
most domain with the flag set, but all the way down the domain tree.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove degenerate scheduler domains during the sched-domain init.
For example on x86_64, we always have NUMA configured in. On Intel EM64T
systems, top most sched domain will be of NUMA and with only one sched_group
in it.
With fork/exec balances(recent Nick's fixes in -mm tree), we always endup
taking wrong decisions because of this topmost domain (as it contains only one
group and find_idlest_group always returns NULL). We will endup loading HT
package completely first, letting active load balance kickin and correct it.
In general, this patch also makes sense with out recent Nick's fixes in -mm.
From: Nick Piggin <nickpiggin@yahoo.com.au>
Modified to account for more than just sched_groups when scanning for
degenerate domains by Nick Piggin. And allow a runqueue's sd to go NULL
rather than keep a single degenerate domain around (this happens when you run
with maxcpus=1).
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix the last 2 places that directly access a runqueue's sched-domain and
assume it cannot be NULL.
That allows the use of NULL for domain, instead of a dummy domain, to signify
no balancing is to happen. No functional changes.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of requiring architecture code to interact with the scheduler's
locking implementation, provide a couple of defines that can be used by the
architecture to request runqueue unlocked context switches, and ask for
interrupts to be enabled over the context switch.
Also replaces the "switch_lock" used by these architectures with an oncpu
flag (note, not a potentially slow bitflag). This eliminates one bus
locked memory operation when context switching, and simplifies the
task_running function.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Reimplement the balance on exec balancing to be sched-domains aware. Use this
to also do balance on fork balancing. Make x86_64 do balance on fork over the
NUMA domain.
The problem that the non sched domains aware blancing became apparent on dual
core, multi socket opterons. What we want is for the new tasks to be sent to
a different socket, but more often than not, we would first load up our
sibling core, or fill two cores of a single remote socket before selecting a
new one.
This gives large improvements to STREAM on such systems.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the very aggressive idle stuff that has recently gone into 2.6 - it is
going against the direction we are trying to go. Hopefully we can regain
performance through other methods.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do less affine wakeups. We're trying to reduce dbt2-pgsql idle time
regressions here... make sure we don't don't move tasks the wrong way in an
imbalance condition. Also, remove the cache coldness requirement from the
calculation - this seems to induce sharp cutoff points where behaviour will
suddenly change on some workloads if the load creeps slightly over or under
some point. It is good for periodic balancing because in that case have
otherwise have no other context to determine what task to move.
But also make a minor tweak to "wake balancing" - the imbalance tolerance is
now set at half the domain's imbalance, so we get the opportunity to do wake
balancing before the more random periodic rebalancing gets preformed.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do CPU load averaging over a number of different intervals. Allow each
interval to be chosen by sending a parameter to source_load and target_load.
0 is instantaneous, idx > 0 returns a decaying average with the most recent
sample weighted at 2^(idx-1). To a maximum of 3 (could be easily increased).
So generally a higher number will result in more conservative balancing.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the special casing for idle CPU balancing. Things like this are
hurting for example on SMT, where are single sibling being idle doesn't really
warrant a really aggressive pull over the NUMA domain, for example.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These conditions should now be impossible, and we need to fix them if they
happen.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SMT balancing has a couple of problems. Firstly, active_load_balance is too
complex - basically it should be a dumb helper for when the periodic balancer
has determined there is an imbalance, but gets stuck because the task is
running.
So rip out all its "smarts", and just make it move one task to the target CPU.
Second, the busy CPU's sched-domain tree was being used for active balancing.
This means that it may not see that nr_balance_failed has reached a critical
level. So use the target CPU's sched-domain tree for this. We can do this
because we hold its runqueue lock.
Lastly, reset nr_balance_failed to a point where we allow cache hot migration.
This will help ensure active load balancing is successful.
Thanks to Suresh Siddha for pointing out these issues.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up active load balancing a bit so it doesn't get called when it shouldn't.
Reset the nr_balance_failed counter at more points where we have found
conditions to be balanced. This reduces too aggressive active balancing seen
on some workloads.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
John Hawkes explained the problem best:
A large number of processes that are pinned to a single CPU results
in every other CPU's load_balance() seeing this overloaded CPU as
"busiest", yet move_tasks() never finds a task to pull-migrate. This
condition occurs during module unload, but can also occur as a
denial-of-service using sys_sched_setaffinity(). Several hundred
CPUs performing this fruitless load_balance() will livelock on the
busiest CPU's runqueue lock. A smaller number of CPUs will livelock
if the pinned task count gets high.
Expanding slightly on John's patch, this one attempts to work out whether the
balancing failure has been due to too many tasks pinned on the runqueue. This
allows it to be basically invisible to the regular blancing paths (ie. when
there are no pinned tasks). We can use this extra knowledge to shut down the
balancing faster, and ensure the migration threads don't start running which
is another problem observed in the wild.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
New sched-domains code means we don't get spans with offline CPUs in
them.
Signed-off-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Show swsuspend only on .config where it can compile. I got this on PPC32 &&
SMP:
kernel/power/smp.c:24: error: storage size of `ctxt' isn't known
Also mark swsusp as no longer experimental.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the cpu hotplug case, per-cpu data possibly isn't initialized even the
system state is 'running'. As the comments say in the original code, some
console drivers assume per-cpu resources have been allocated. radeon fb is
one such driver, which uses kmalloc. After a CPU is down, the per-cpu data
of slab is freed, so the system crashed when printing some info.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch moves the recalculation of nr_copy_pages so that the right
number is used in the calculation of the size of memory and swap needed.
It prevents swsusp from attempting to suspend if there is not enough memory
and/or swap (which is unlikely anyway).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch cleans up whitespace in swsusp.c (a bit):
- removes any trailing whitespace
- adds spaces after if, for, for_each_pbe, for_each_zone etc., wherever
necessary.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following patch removes the unnecessary function does_collide_order().
This function is no longer necessary, as currently there are only 0-order
allocations in swsusp, and the use of it is confusing.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without this patch, Linux provokes emergency disk shutdowns and
similar nastiness. It was in SuSE kernels for some time, IIRC.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using CPU hotplug to support suspend/resume SMP. Both S3 and S4 use
disable/enable_nonboot_cpus API. The S4 part is based on Pavel's original S4
SMP patch.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(The i386 CPU hotplug patch provides infrastructure for some work which Pavel
is doing as well as for ACPI S3 (suspend-to-RAM) work which Li Shaohua
<shaohua.li@intel.com> is doing)
The following provides i386 architecture support for safely unregistering and
registering processors during runtime, updated for the current -mm tree. In
order to avoid dumping cpu hotplug code into kernel/irq/* i dropped the
cpu_online check in do_IRQ() by modifying fixup_irqs(). The difference being
that on cpu offline, fixup_irqs() is called before we clear the cpu from
cpu_online_map and a long delay in order to ensure that we never have any
queued external interrupts on the APICs. There are additional changes to s390
and ppc64 to account for this change.
1) Add CONFIG_HOTPLUG_CPU
2) disable local APIC timer on dead cpus.
3) Disable preempt around irq balancing to prevent CPUs going down.
4) Print irq stats for all possible cpus.
5) Debugging check for interrupts on offline cpus.
6) Hacky fixup_irqs() to redirect irqs when cpus go off/online.
7) play_dead() for offline cpus to spin inside.
8) Handle offline cpus set in flush_tlb_others().
9) Grab lock earlier in smp_call_function() to prevent CPUs going down.
10) Implement __cpu_disable() and __cpu_die().
11) Enable local interrupts in cpu_enable() after fixup_irqs()
12) Don't fiddle with NMI on dead cpu, but leave intact on other cpus.
13) Program IRQ affinity whilst cpu is still in cpu_online_map on offline.
Signed-off-by: Zwane Mwaikambo <zwane@linuxpower.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't look up the task by its pid and then use the syscall filtering
helper. Just implement our own filter helper which operates solely on
the information in the netlink_skb_parms.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When the task refcounting was added to audit_filter_rules() it became
more of a problem that this function was violating the 'only one
return from each function' rule. In fixing it to use a variable to store
'ret' I stupidly neglected to actually change the 'return 1;' at the
end. This makes it not work very well.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Another rollup of patches which give various symbols static scope
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds version and srcversion files to
/sys/module/${modulename} containing the version and srcversion fields
of the module's modinfo section (if present).
/sys/module/e1000
|-- srcversion
`-- version
This patch differs slightly from the version posted in January, as it
now uses the new kstrdup() call in -mm.
Why put this in sysfs?
a) Tools like DKMS, which deal with changing out individual kernel
modules without replacing the whole kernel, can behave smarter if they
can tell the version of a given module. The autoinstaller feature, for
example, which determines if your system has a "good" version of a
driver (i.e. if the one provided by DKMS has a newer verson than that
provided by the kernel package installed), and to automatically compile
and install a newer version if DKMS has it but your kernel doesn't yet
have that version.
b) Because sysadmins manually, or with tools like DKMS, can switch out
modules on the file system, you can't count on 'modinfo foo.ko', which
looks at /lib/modules/${kernelver}/... actually matching what is loaded
into the kernel already. Hence asking sysfs for this.
c) as the unbind-driver-from-device work takes shape, it will be
possible to rebind a driver that's built-in (no .ko to modinfo for the
version) to a newly loaded module. sysfs will have the
currently-built-in version info, for comparison.
d) tech support scripts can then easily grab the version info for what's
running presently - a question I get often.
There has been renewed interest in this patch on linux-scsi by driver
authors.
As the idea originated from GregKH, I leave his Signed-off-by: intact,
though the implementation is nearly completely new. Compiled and run on
x86 and x86_64.
From: Matthew Dobson <colpatch@us.ibm.com>
build fix
From: Thierry Vignaud <tvignaud@mandriva.com>
build fix
From: Matthew Dobson <colpatch@us.ibm.com>
warning fix
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch makes the following changes:
(1) There's a new special key type called ".request_key_auth".
This is an authorisation key for when one process requests a key and
another process is started to construct it. This type of key cannot be
created by the user; nor can it be requested by kernel services.
Authorisation keys hold two references:
(a) Each refers to a key being constructed. When the key being
constructed is instantiated the authorisation key is revoked,
rendering it of no further use.
(b) The "authorising process". This is either:
(i) the process that called request_key(), or:
(ii) if the process that called request_key() itself had an
authorisation key in its session keyring, then the authorising
process referred to by that authorisation key will also be
referred to by the new authorisation key.
This means that the process that initiated a chain of key requests
will authorise the lot of them, and will, by default, wind up with
the keys obtained from them in its keyrings.
(2) request_key() creates an authorisation key which is then passed to
/sbin/request-key in as part of a new session keyring.
(3) When request_key() is searching for a key to hand back to the caller, if
it comes across an authorisation key in the session keyring of the
calling process, it will also search the keyrings of the process
specified therein and it will use the specified process's credentials
(fsuid, fsgid, groups) to do that rather than the calling process's
credentials.
This allows a process started by /sbin/request-key to find keys belonging
to the authorising process.
(4) A key can be read, even if the process executing KEYCTL_READ doesn't have
direct read or search permission if that key is contained within the
keyrings of a process specified by an authorisation key found within the
calling process's session keyring, and is searchable using the
credentials of the authorising process.
This allows a process started by /sbin/request-key to read keys belonging
to the authorising process.
(5) The magic KEY_SPEC_*_KEYRING key IDs when passed to KEYCTL_INSTANTIATE or
KEYCTL_NEGATE will specify a keyring of the authorising process, rather
than the process doing the instantiation.
(6) One of the process keyrings can be nominated as the default to which
request_key() should attach new keys if not otherwise specified. This is
done with KEYCTL_SET_REQKEY_KEYRING and one of the KEY_REQKEY_DEFL_*
constants. The current setting can also be read using this call.
(7) request_key() is partially interruptible. If it is waiting for another
process to finish constructing a key, it can be interrupted. This permits
a request-key cycle to be broken without recourse to rebooting.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-Off-By: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch makes it possible to pass a session keyring through to the
process spawned by call_usermodehelper(). This allows patch 3/3 to pass an
authorisation key through to /sbin/request-key, thus permitting better access
controls when doing just-in-time key creation.
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the upcoming aio_down patch, it is useful to store a private data
pointer in the kiocb's wait_queue. Since we provide our own wake up
function and do not require the task_struct pointer, it makes sense to
convert the task pointer into a generic private pointer.
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Avoid taking the tasklist_lock in sys_times if the process is single
threaded. In a NUMA system taking the tasklist_lock may cause a bouncing
cacheline if multiple independent processes continually call sys_times to
measure their performance.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes recalc_sigpending() to work correctly with tasks which are
being freezed.
The problem is that freeze_processes() sets PF_FREEZE and TIF_SIGPENDING
flags on tasks, but recalc_sigpending() called from e.g.
sys_rt_sigtimedwait or any other kernel place will clear TIF_SIGPENDING due
to no pending signals queued and the tasks won't be freezed until it
recieves a real signal or freezed_processes() fail due to timeout.
Signed-Off-By: Kirill Korotaev <dev@sw.ru>
Signed-Off-By: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new `suid_dumpable' sysctl:
This value can be used to query and set the core dump mode for setuid
or otherwise protected/tainted binaries. The modes are
0 - (default) - traditional behaviour. Any process which has changed
privilege levels or is execute only will not be dumped
1 - (debug) - all processes dump core when possible. The core dump is
owned by the current user and no security is applied. This is intended
for system debugging situations only. Ptrace is unchecked.
2 - (suidsafe) - any binary which normally would not be dumped is dumped
readable by root only. This allows the end user to remove such a dump but
not access it directly. For security reasons core dumps in this mode will
not overwrite one another or other files. This mode is appropriate when
adminstrators are attempting to debug problems in a normal environment.
(akpm:
> > +EXPORT_SYMBOL(suid_dumpable);
>
> EXPORT_SYMBOL_GPL?
No problem to me.
> > if (current->euid == current->uid && current->egid == current->gid)
> > current->mm->dumpable = 1;
>
> Should this be SUID_DUMP_USER?
Actually the feedback I had from last time was that the SUID_ defines
should go because its clearer to follow the numbers. They can go
everywhere (and there are lots of places where dumpable is tested/used
as a bool in untouched code)
> Maybe this should be renamed to `dump_policy' or something. Doing that
> would help us catch any code which isn't using the #defines, too.
Fair comment. The patch was designed to be easy to maintain for Red Hat
rather than for merging. Changing that field would create a gigantic
diff because it is used all over the place.
)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Presently either multiple kprobes or only one jprobe could be inserted.
This patch removes the above limitation and allows one jprobe and multiple
kprobes to coexist at the same address. However multiple jprobes cannot
coexist with multiple kprobes. Currently I am working on the prototype to
allow multiple jprobes coexist with multiple kprobes.
Signed-off-by: Ananth N Mavinakayanhalli <amavin@redhat.com>
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In situations where a kprobes handler calls a routine which has a probe on it,
then kprobes_handler() disarms the new probe forever. This patch removes the
above limitation by temporarily disarming the new probe. When the another
probe hits while handling the old probe, the kprobes_handler() saves previous
kprobes state and handles the new probe without calling the new kprobes
registered handlers. kprobe_post_handler() restores back the previous kprobes
state and the normal execution continues.
However on x86_64 architecture, re-rentrancy is provided only through
pre_handler(). If a routine having probe is referenced through
post_handler(), then the probes on that routine are disarmed forever, since
the exception stack is gets changed after the processor single steps the
instruction of the new probe.
This patch includes generic changes to support temporary disarming on
reentrancy of probes.
Signed-of-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the lock/unlock of the arch specific kprobe_flush_task()
to the non-arch specific kprobe_flusk_task().
Signed-off-by: Hien Nguyen <hien@us.ibm.com>
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The architecture independent code of the current kprobes implementation is
arming and disarming kprobes at registration time. The problem is that the
code is assuming that arming and disarming is a just done by a simple write
of some magic value to an address. This is problematic for ia64 where our
instructions look more like structures, and we can not insert break points
by just doing something like:
*p->addr = BREAKPOINT_INSTRUCTION;
The following patch to 2.6.12-rc4-mm2 adds two new architecture dependent
functions:
* void arch_arm_kprobe(struct kprobe *p)
* void arch_disarm_kprobe(struct kprobe *p)
and then adds the new functions for each of the architectures that already
implement kprobes (spar64/ppc64/i386/x86_64).
I thought arch_[dis]arm_kprobe was the most descriptive of what was really
happening, but each of the architectures already had a disarm_kprobe()
function that was really a "disarm and do some other clean-up items as
needed when you stumble across a recursive kprobe." So... I took the
liberty of changing the code that was calling disarm_kprobe() to call
arch_disarm_kprobe(), and then do the cleanup in the block of code dealing
with the recursive kprobe case.
So far this patch as been tested on i386, x86_64, and ppc64, but still
needs to be tested in sparc64.
Signed-off-by: Rusty Lynch <rusty.lynch@intel.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds function-return probes to kprobes for the i386
architecture. This enables you to establish a handler to be run when a
function returns.
1. API
Two new functions are added to kprobes:
int register_kretprobe(struct kretprobe *rp);
void unregister_kretprobe(struct kretprobe *rp);
2. Registration and unregistration
2.1 Register
To register a function-return probe, the user populates the following
fields in a kretprobe object and calls register_kretprobe() with the
kretprobe address as an argument:
kp.addr - the function's address
handler - this function is run after the ret instruction executes, but
before control returns to the return address in the caller.
maxactive - The maximum number of instances of the probed function that
can be active concurrently. For example, if the function is non-
recursive and is called with a spinlock or mutex held, maxactive = 1
should be enough. If the function is non-recursive and can never
relinquish the CPU (e.g., via a semaphore or preemption), NR_CPUS should
be enough. maxactive is used to determine how many kretprobe_instance
objects to allocate for this particular probed function. If maxactive <=
0, it is set to a default value (if CONFIG_PREEMPT maxactive=max(10, 2 *
NR_CPUS) else maxactive=NR_CPUS)
For example:
struct kretprobe rp;
rp.kp.addr = /* entrypoint address */
rp.handler = /*return probe handler */
rp.maxactive = /* e.g., 1 or NR_CPUS or 0, see the above explanation */
register_kretprobe(&rp);
The following field may also be of interest:
nmissed - Initialized to zero when the function-return probe is
registered, and incremented every time the probed function is entered but
there is no kretprobe_instance object available for establishing the
function-return probe (i.e., because maxactive was set too low).
2.2 Unregister
To unregiter a function-return probe, the user calls
unregister_kretprobe() with the same kretprobe object as registered
previously. If a probed function is running when the return probe is
unregistered, the function will return as expected, but the handler won't
be run.
3. Limitations
3.1 This patch supports only the i386 architecture, but patches for
x86_64 and ppc64 are anticipated soon.
3.2 Return probes operates by replacing the return address in the stack
(or in a known register, such as the lr register for ppc). This may
cause __builtin_return_address(0), when invoked from the return-probed
function, to return the address of the return-probes trampoline.
3.3 This implementation uses the "Multiprobes at an address" feature in
2.6.12-rc3-mm3.
3.4 Due to a limitation in multi-probes, you cannot currently establish
a return probe and a jprobe on the same function. A patch to remove
this limitation is being tested.
This feature is required by SystemTap (http://sourceware.org/systemtap),
and reflects ideas contributed by several SystemTap developers, including
Will Cohen and Ananth Mavinakayanahalli.
Signed-off-by: Hien Nguyen <hien@us.ibm.com>
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@laposte.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Prevent recursive faults in do_exit() by leaving the task alone and wait
for reboot. This may allow a more graceful shutdown and possibly save the
original oops.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Various filesystem drivers have grown a get_dentry() function that's a
duplicate of lookup_one_len, except that it doesn't take a maximum length
argument and doesn't check for \0 or / in the passed in filename.
Switch all these places to use lookup_one_len.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Greg KH <greg@kroah.com>
Cc: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In kernel/sched.c the return value from preempt_count() is cast to an int.
That made sense when preempt_count was defined as different types on is not
needed and should go away. The patch removes the cast.
In kernel/timer.c the return value from preempt_count() is assigned to a
variable of type u32 and then that unsigned value is later compared to
preempt_count(). Since preempt_count() returns an int, an int is what
should be used to store its return value. Storing the result in an
unsigned 32bit integer made a tiny bit of sense back when preempt_count was
different types on different archs, but no more - let's not play signed vs
unsigned comparison games when we don't have to. The patch modifies the
code to use an int to hold the value. While I was around that bit of code
I also made two changes to a nearby (related) printk() - I modified it to
specify the loglevel explicitly and also broke the line into a few pieces
to avoid it being longer than 80 chars and clarified the text a bit.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
According to include/linux/console.h, CON_CONSDEV flag should be set on
the last console specified on the boot command line:
86 #define CON_PRINTBUFFER (1)
87 #define CON_CONSDEV (2) /* Last on the command line */
88 #define CON_ENABLED (4)
89 #define CON_BOOT (8)
This does not currently happen if there is more than one console specified
on the boot commandline. Instead, it gets set on the first console on the
command line. This can cause problems for things like kdb that look for
the CON_CONSDEV flag to see if the console is valid.
Additionaly, it doesn't look like CON_CONSDEV is reassigned to the next
preferred console at unregister time if the console being unregistered
currently has that bit set.
Example (from sn2 ia64):
elilo vmlinuz root=<dev> console=ttyS0 console=ttySG0
in this case, the flags on ttySG console struct will be 0x4 (should be
0x6).
Attached patch against bk fixes both issues for the cases I looked at. It
uses selected_console (which gets incremented for each console specified on
the command line) as the indicator of which console to set CON_CONSDEV on.
When adding the console to the list, if the previous one had CON_CONSDEV
set, it masks it out. Tested on ia64 and x86.
The problem with the current behavior is it breaks overriding the default from
the boot line. In the ia64 case, there may be a global append line defining
console=a in elilo.conf. Then you want to boot your kernel, and want to
override the default by passing console=b on the boot line. elilo constructs
the kernel cmdline by starting with the value of the global append line, then
tacks on whatever else you specify, which puts console=b last.
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_timer_settime/sys_timer_delete needs to delete k_itimer->real.timer
synchronously while holding ->it_lock, which is also locked in
posix_timer_fn.
This patch removes timer_active/set_timer_inactive which plays with
timer_list's internals in favour of using try_to_del_timer_sync(), which
was introduced in the previous patch.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch splits del_timer_sync() into 2 functions. The new one,
try_to_del_timer_sync(), returns -1 when it hits executing timer.
It can be used in interrupt context, or when the caller hold locks which
can prevent completion of the timer's handler.
NOTE. Currently it can't be used in interrupt context in UP case, because
->running_timer is used only with CONFIG_SMP.
Should the need arise, it is possible to kill #ifdef CONFIG_SMP in
set_running_timer(), it is cheap.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch tries to solve following problems:
1. del_timer_sync() is racy. The timer can be fired again after
del_timer_sync have checked all cpus and before it will recheck
timer_pending().
2. It has scalability problems. All cpus are scanned to determine
if the timer is running on that cpu.
With this patch del_timer_sync is O(1) and no slower than plain
del_timer(pending_timer), unless it has to actually wait for
completion of the currently running timer.
The only restriction is that the recurring timer should not use
add_timer_on().
3. The timers are not serialized wrt to itself.
If CPU_0 does mod_timer(jiffies+1) while the timer is currently
running on CPU 1, it is quite possible that local interrupt on
CPU_0 will start that timer before it finished on CPU_1.
4. The timers locking is suboptimal. __mod_timer() takes 3 locks
at once and still requires wmb() in del_timer/run_timers.
The new implementation takes 2 locks sequentially and does not
need memory barriers.
Currently ->base != NULL means that the timer is pending. In that case
->base.lock is used to lock the timer. __mod_timer also takes timer->lock
because ->base can be == NULL.
This patch uses timer->entry.next != NULL as indication that the timer is
pending. So it does __list_del(), entry->next = NULL instead of list_del()
when the timer is deleted.
The ->base field is used for hashed locking only, it is initialized
in init_timer() which sets ->base = per_cpu(tvec_bases). When the
tvec_bases.lock is locked, it means that all timers which are tied
to this base via timer->base are locked, and the base itself is locked
too.
So __run_timers/migrate_timers can safely modify all timers which could
be found on ->tvX lists (pending timers).
When the timer's base is locked, and the timer removed from ->entry list
(which means that _run_timers/migrate_timers can't see this timer), it is
possible to set timer->base = NULL and drop the lock: the timer remains
locked.
This patch adds lock_timer_base() helper, which waits for ->base != NULL,
locks the ->base, and checks it is still the same.
__mod_timer() schedules the timer on the local CPU and changes it's base.
However, it does not lock both old and new bases at once. It locks the
timer via lock_timer_base(), deletes the timer, sets ->base = NULL, and
unlocks old base. Then __mod_timer() locks new_base, sets ->base = new_base,
and adds this timer. This simplifies the code, because AB-BA deadlock is not
possible. __mod_timer() also ensures that the timer's base is not changed
while the timer's handler is running on the old base.
__run_timers(), del_timer() do not change ->base anymore, they only clear
pending flag.
So del_timer_sync() can test timer->base->running_timer == timer to detect
whether it is running or not.
We don't need timer_list->lock anymore, this patch kills it.
We also don't need barriers. del_timer() and __run_timers() used smp_wmb()
before clearing timer's pending flag. It was needed because __mod_timer()
did not lock old_base if the timer is not pending, so __mod_timer()->list_add()
could race with del_timer()->list_del(). With this patch these functions are
serialized through base->lock.
One problem. TIMER_INITIALIZER can't use per_cpu(tvec_bases). So this patch
adds global
struct timer_base_s {
spinlock_t lock;
struct timer_list *running_timer;
} __init_timer_base;
which is used by TIMER_INITIALIZER. The corresponding fields in tvec_t_base_s
struct are replaced by struct timer_base_s t_base.
It is indeed ugly. But this can't have scalability problems. The global
__init_timer_base.lock is used only when __mod_timer() is called for the first
time AND the timer was compile time initialized. After that the timer migrates
to the local CPU.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Renaud Lienhart <renaud.lienhart@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the timer frequency selectable. The timer interrupt may cause bus
and memory contention in large NUMA systems since the interrupt occurs
on each processor HZ times per second.
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a gfp_mask to audit_log_start() and audit_log(), to reduce the
amount of GFP_ATOMIC allocation -- most of it doesn't need to be
GFP_ATOMIC. Also if the mask includes __GFP_WAIT, then wait up to
60 seconds for the auditd backlog to clear instead of immediately
abandoning the message.
The timeout should probably be made configurable, but for now it'll
suffice that it only happens if auditd is actually running.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
With Chris Wedgwood <cw@f00f.org>
As suggested by Chris, we can make the "just added" method ->release
conditional to UML only (better: to archs requesting it, i.e. only UML
currently), so that other archs don't get this unneeded crud, and if UML
won't need it any more we can kill this.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Chris Wedgwood <cw@f00f.org>
Currently UML must explicitly call the UML-specific
free_irq_by_irq_and_dev() for each free_irq call it's done.
This is needed because ->shutdown and/or ->disable are only called when the
last "action" for that irq is removed.
Instead, for UML shared IRQs (UML IRQs are very often, if not always,
shared), for each dev_id some setup is done, which must be cleared on the
release of that fd. For instance, for each open console a new instance
(i.e. new dev_id) of the same IRQ is requested().
Exactly, a fd is stored in an array (pollfds), which is after read by a
host thread and passed to poll(). Each event registered by poll() triggers
an interrupt. So, for each free_irq() we must remove the corresponding
host fd from the table, which we do via this -release() method.
In this patch we add an appropriate hook for this, and remove all uses of
it by pointing the hook to the said procedure; this is safe to do since the
said procedure.
Also some cosmetic improvements are included.
This is heavily based on some work by Chris Wedgwood, which however didn't
get the patch merged for something I'd call a "misunderstanding" (the need
for this patch wasn't cleanly explained, thus adding the generic hook was
felt as undesirable).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove part of comment on linking new vma in dup_mmap: since anon_vma rmap
came in, try_to_unmap_one knows the vma without needing find_vma. But add
a comment to note that here vma is inserted without mmap_sem.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ingo recently introduced a great speedup for allocating new mmaps using the
free_area_cache pointer which boosts the specweb SSL benchmark by 4-5% and
causes huge performance increases in thread creation.
The downside of this patch is that it does lead to fragmentation in the
mmap-ed areas (visible via /proc/self/maps), such that some applications
that work fine under 2.4 kernels quickly run out of memory on any 2.6
kernel.
The problem is twofold:
1) the free_area_cache is used to continue a search for memory where
the last search ended. Before the change new areas were always
searched from the base address on.
So now new small areas are cluttering holes of all sizes
throughout the whole mmap-able region whereas before small holes
tended to close holes near the base leaving holes far from the base
large and available for larger requests.
2) the free_area_cache also is set to the location of the last
munmap-ed area so in scenarios where we allocate e.g. five regions of
1K each, then free regions 4 2 3 in this order the next request for 1K
will be placed in the position of the old region 3, whereas before we
appended it to the still active region 1, placing it at the location
of the old region 2. Before we had 1 free region of 2K, now we only
get two free regions of 1K -> fragmentation.
The patch addresses thes issues by introducing yet another cache descriptor
cached_hole_size that contains the largest known hole size below the
current free_area_cache. If a new request comes in the size is compared
against the cached_hole_size and if the request can be filled with a hole
below free_area_cache the search is started from the base instead.
The results look promising: Whereas 2.6.12-rc4 fragments quickly and my
(earlier posted) leakme.c test program terminates after 50000+ iterations
with 96 distinct and fragmented maps in /proc/self/maps it performs nicely
(as expected) with thread creation, Ingo's test_str02 with 20000 threads
requires 0.7s system time.
Taking out Ingo's patch (un-patch available per request) by basically
deleting all mentions of free_area_cache from the kernel and starting the
search for new memory always at the respective bases we observe: leakme
terminates successfully with 11 distinctive hardly fragmented areas in
/proc/self/maps but thread creating is gringdingly slow: 30+s(!) system
time for Ingo's test_str02 with 20000 threads.
Now - drumroll ;-) the appended patch works fine with leakme: it ends with
only 7 distinct areas in /proc/self/maps and also thread creation seems
sufficiently fast with 0.71s for 20000 threads.
Signed-off-by: Wolfgang Wander <wwc@rentec.com>
Credit-to: "Richard Purdie" <rpurdie@rpsys.net>
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu> (partly)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the core of the (much simplified) early reclaim. The goal of this
patch is to reclaim some easily-freed pages from a zone before falling back
onto another zone.
One of the major uses of this is NUMA machines. With the default allocator
behavior the allocator would look for memory in another zone, which might be
off-node, before trying to reclaim from the current zone.
This adds a zone tuneable to enable early zone reclaim. It is selected on a
per-zone basis and is turned on/off via syscall.
Adding some extra throttling on the reclaim was also required (patch
4/4). Without the machine would grind to a crawl when doing a "make -j"
kernel build. Even with this patch the System Time is higher on
average, but it seems tolerable. Here are some numbers for kernbench
runs on a 2-node, 4cpu, 8Gig RAM Altix in the "make -j" run:
wall user sys %cpu ctx sw. sleeps
---- ---- --- ---- ------ ------
No patch 1009 1384 847 258 298170 504402
w/patch, no reclaim 880 1376 667 288 254064 396745
w/patch & reclaim 1079 1385 926 252 291625 548873
These numbers are the average of 2 runs of 3 "make -j" runs done right
after system boot. Run-to-run variability for "make -j" is huge, so
these numbers aren't terribly useful except to seee that with reclaim
the benchmark still finishes in a reasonable amount of time.
I also looked at the NUMA hit/miss stats for the "make -j" runs and the
reclaim doesn't make any difference when the machine is thrashing away.
Doing a "make -j8" on a single node that is filled with page cache pages
takes 700 seconds with reclaim turned on and 735 seconds without reclaim
(due to remote memory accesses).
The simple zone_reclaim syscall program is at
http://www.bork.org/~mort/sgi/zone_reclaim.c
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch implements a number of smp_processor_id() cleanup ideas that
Arjan van de Ven and I came up with.
The previous __smp_processor_id/_smp_processor_id/smp_processor_id API
spaghetti was hard to follow both on the implementational and on the
usage side.
Some of the complexity arose from picking wrong names, some of the
complexity comes from the fact that not all architectures defined
__smp_processor_id.
In the new code, there are two externally visible symbols:
- smp_processor_id(): debug variant.
- raw_smp_processor_id(): nondebug variant. Replaces all existing
uses of _smp_processor_id() and __smp_processor_id(). Defined
by every SMP architecture in include/asm-*/smp.h.
There is one new internal symbol, dependent on DEBUG_PREEMPT:
- debug_smp_processor_id(): internal debug variant, mapped to
smp_processor_id().
Also, i moved debug_smp_processor_id() from lib/kernel_lock.c into a new
lib/smp_processor_id.c file. All related comments got updated and/or
clarified.
I have build/boot tested the following 8 .config combinations on x86:
{SMP,UP} x {PREEMPT,!PREEMPT} x {DEBUG_PREEMPT,!DEBUG_PREEMPT}
I have also build/boot tested x64 on UP/PREEMPT/DEBUG_PREEMPT. (Other
architectures are untested, but should work just fine.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we have enough rules to fill the netlink buffer space, it'll
deadlock because auditctl isn't ever actually going to read from the
socket until we return, and we aren't going to return until it
reads... so we spawn a kernel thread to spew out the list and then
exit.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
sysfs: fix the rest of the kernel so if an attribute doesn't
implement show or store method read/write will return
-EIO instead of 0 or -EINVAL or -EPERM.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When LOOKUP_PARENT is used, the inode which results is not the inode
found at the pathname. Report the flags so that this doesn't generate
misleading audit records.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Turn the field from a bitmask to an enumeration and add a list to allow
filtering of messages generated by userspace. We also define a list for
file system watches in anticipation of that feature.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
On one path, cond_resched_lock() fails to return true if it dropped the lock.
We think this might be causing the crashes in JBD's log_do_checkpoint().
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
flush_icache_range() is used in two different situation - in binfmt_elf.c &
co for user space mappings and module.c for kernel modules. On m68k
flush_icache_range() doesn't know which data to flush, as it has separate
address spaces and the pointer argument can be valid in either address
space.
First I considered splitting flush_icache_range(), but this patch is
simpler. Setting the correct context gives flush_icache_range() enough
information to flush the correct data.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The "unhandled interrupts" catcher, note_interrupt(), increments a global
desc->irq_count and grossly damages scaling of very large systems, e.g.,
>192p ia64 Altix, because of this highly contented cacheline, especially
for timer interrupts. 384p is severely crippled, and 512p is unuseable.
All calls to note_interrupt() can be disabled by booting with "noirqdebug",
but this disables the useful interrupt checking for all interrupts.
I propose eliminating note_interrupt() for all per-CPU interrupts. This
was the behavior of linux-2.6.10 and earlier, but in 2.6.11 a code
restructuring added a call to note_interrupt() for per-CPU interrupts.
Besides, note_interrupt() is a bit racy for concurrent CPU calls anyway, as
the desc->irq_count++ increment isn't atomic (which, if done, would make
scaling even worse).
Signed-off-by: John Hawkes <hawkes@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a race in the kernel cpuset code, between the code
to handle notify_on_release, and the code to remove a cpuset.
The notify_on_release code can end up trying to access a
cpuset that has been removed. In the most common case, this
causes a NULL pointer dereference from the routine cpuset_path.
However all manner of bad things are possible, in theory at least.
The existing code decrements the cpuset use count, and if the
count goes to zero, processes the notify_on_release request,
if appropriate. However, once the count goes to zero, unless we
are holding the global cpuset_sem semaphore, there is nothing to
stop another task from immediately removing the cpuset entirely,
and recycling its memory.
The obvious fix would be to always hold the cpuset_sem
semaphore while decrementing the use count and dealing with
notify_on_release. However we don't want to force a global
semaphore into the mainline task exit path, as that might create
a scaling problem.
The actual fix is almost as easy - since this is only an issue
for cpusets using notify_on_release, which the top level big
cpusets don't normally need to use, only take the cpuset_sem
for cpusets using notify_on_release.
This code has been run for hours without a hiccup, while running
a cpuset create/destroy stress test that could crash the existing
kernel in seconds. This patch applies to the current -linus
git kernel.
Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Simon Derr <simon.derr@bull.net>
Acked-by: Dinakar Guniguntala <dino@in.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While they were all just simple blobs it made sense to just free them
as we walked through and logged them. Now that there are pointers to
other objects which need refcounting, we might as well revert to
_only_ logging them in audit_log_exit(), and put the code to free them
properly in only one place -- in audit_free_aux().
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
----------------------------------------------------------
If SIGKILL does not have priority, we cannot instantly kill task before it
makes some unexpected job. It can be critical, but we were unable to
reproduce this easily until Heiko Carstens <Heiko.Carstens@de.ibm.com>
reported this problem on LKML.
Signed-Off-By: Kirill Korotaev <dev@sw.ru>
Signed-Off-By: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These changes make processing of audit logs easier. Based on a patch
from Steve Grubb <sgrubb@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Move audit_serial() into audit.c and use it to generate serial numbers
on messages even when there is no audit context from syscall auditing.
This allows us to disambiguate audit records when more than one is
generated in the same millisecond.
Based on a patch by Steve Grubb after he observed the problem.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In _spin_unlock_bh(lock):
do { \
_raw_spin_unlock(lock); \
preempt_enable(); \
local_bh_enable(); \
__release(lock); \
} while (0)
there is no reason for using preempt_enable() instead of a simple
preempt_enable_no_resched()
Since we know bottom halves are disabled, preempt_schedule() will always
return at once (preempt_count!=0), and hence preempt_check_resched() is
useless here...
This fixes it by using "preempt_enable_no_resched()" instead of the
"preempt_enable()", and thus avoids the useless preempt_check_resched()
just before re-enabling bottom halves.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch changes all occurrences of loginuid to auid. It also
changes everything to %u that is an unsigned type.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The original AVC_USER message wasn't consolidated with the new range of
user messages. The attached patch fixes the kernel so the old messages
work again.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch changes the SELinux AVC to defer logging of paths to the audit
framework upon syscall exit, by saving a reference to the (dentry,vfsmount)
pair in an auxiliary audit item on the current audit context for processing
by audit_log_exit.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch removes the entwining of cpusets and hotplug code in the "No
more Mr. Nice Guy" case of sched.c move_task_off_dead_cpu().
Since the hotplug code is holding a spinlock at this point, we cannot take
the cpuset semaphore, cpuset_sem, as would seem to be required either to
update the tasks cpuset, or to scan up the nested cpuset chain, looking for
the nearest cpuset ancestor that still has some CPUs that are online. So
we just punt and blast the tasks cpus_allowed with all bits allowed.
This reverts these lines of code to what they were before the cpuset patch.
And it updates the cpuset Doc file, to match.
The one known alternative to this that seems to work came from Dinakar
Guniguntala, and required the hotplug code to take the cpuset_sem semaphore
much earlier in its processing. So far as we know, the increased locking
entanglement between cpusets and hot plug of this alternative approach is
not worth doing in this case.
Signed-off-by: Paul Jackson <pj@sgi.com>
Acked-by: Nathan Lynch <ntl@pobox.com>
Acked-by: Dinakar Guniguntala <dino@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The limit on the number of outstanding audit messages was inadvertently
removed with the switch to queuing skbs directly for sending by a kernel
thread. Put it back again.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
netlink_unicast() will attempt to reallocate and will free messages if
the socket's rcvbuf limit is reached unless we give it an infinite
timeout. So do that, from a kernel thread which is dedicated to spewing
stuff up the netlink socket.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* If vsnprintf returns -1, it will mess up the sk buffer space accounting.
This is fixed by not calling skb_put with bogus len values.
* audit_log_hex was a loop that called audit_log_vformat with %02X for each
character. This is very inefficient since conversion from unsigned character
to Ascii representation is essentially masking, shifting, and byte lookups.
Also, the length of the converted string is well known - it's twice the
original. Fixed by rewriting the function.
* audit_log_untrustedstring had no comments. This makes it hard for
someone to understand what the string format will be.
* audit_log_d_path was never fixed to use untrustedstring. This could mess
up user space parsers. This was fixed to make a temp buffer, call d_path,
and log temp buffer using untrustedstring.
From: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
It's silly to have to add explicit entries for new userspace messages
as we invent them. Just treat all messages in the user range the same.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch includes various tweaks in the messaging that appears during
system pm state transitions:
* Warn about certain illegal calls in the device tree, like resuming
child before parent or suspending parent before child. This could
happen easily enough through sysfs, or in some cases when drivers
use device_pm_set_parent().
* Be more consistent about dev_dbg() tracing ... do it for resume() and
shutdown() too, and never if the driver doesn't have that method.
* Say which type of system sleep state is being entered.
Except for the warnings, these only affect debug messaging.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
profile=schedule parsing is not quite what it should be. First, str[7] is
'e', not ',', but then even if it did fall through, prof_on =
SCHED_PROFILING would be clobbered inside if (get_option(...)) So a small
amount of rearrangement is done in this patch to correct it.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move add_preferred_console out of CONFIG_PRINTK so serial console does the
right thing.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On my IA64 machine, after kernel 2.6.12-rc3 boots, an edge-triggered
interrupt (IRQ 46) keeps triggered over and over again. There is no IRQ 46
interrupt action handler. It has lots of impact on performance.
Kernel 2.6.10 and its prior versions have no the problem. Basically,
kernel 2.6.10 will mask the spurious edge interrupt if the interrupt is
triggered for the second time and its status includes
IRQ_DISABLE|IRQ_PENDING.
Originally, IA64 kernel has its own specific _irq_desc definitions in file
arch/ia64/kernel/irq.c. The definition initiates _irq_desc[irq].status to
IRQ_DISABLE. Since kernel 2.6.11, it was moved to architecture independent
codes, i.e. kernel/irq/handle.c, but kernel/irq/handle.c initiates
_irq_desc[irq].status to 0 instead of IRQ_DISABLE.
Signed-off-by: Zhang Yanmin <yanmin.zhang@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Der... if you use max_t it helps if you give it a type.
Note to self: Always just apply the tested patches, don't try to port
them by hand. You're not clever enough.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I'm going through the kernel code and have a patch that corrects
several spelling errors in comments.
From: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch adds more messages types to the audit subsystem so that audit
analysis is quicker, intuitive, and more useful.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
---
I forgot one type in the big patch. I need to add one for user space
originating SE Linux avc messages. This is used by dbus and nscd.
-Steve
---
Updated to 2.6.12-rc4-mm1.
-dwmw2
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Otherwise, we will be repeatedly reallocating, even if we're only
adding a few bytes at a time. Pointed out by Steve Grubb.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add audit_log_type to allow callers to specify type and pid when logging.
Convert audit_log to wrapper around audit_log_type. Could have
converted all audit_log callers directly, but common case is default
of type AUDIT_KERNEL and pid 0. Update audit_log_start to take type
and pid values when creating a new audit_buffer. Move sequences that
did audit_log_start, audit_log_format, audit_set_type, audit_log_end,
to simply call audit_log_type directly. This obsoletes audit_set_type
and audit_set_pid, so remove them.
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Remove code conditionally dependent on CONFIG_AUDITSYSCALL from audit.c.
Move these dependencies to audit.h with the rest.
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Audit now actually requires netlink. So make it depend on CONFIG_NET,
and remove the inline dependencies on CONFIG_NET.
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Let audit_expand() know how much it's expected to grow the buffer, in
the case that we have that information to hand.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We were setting nlmsg_len to skb->len, but we should be subtracting
the size of the header.
From: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Drop the use of a tmp buffer in the audit_buffer, and just buffer
directly to the skb. All header data that was temporarily stored in
the audit_buffer can now be stored directly in the netlink header in
the skb. Resize skb as needed. This eliminates the extra copy (and
the audit_log_move function which was responsible for copying).
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Introduce audit_expand and make the audit_buffer use a dynamic buffer
which can be resized. When audit buffer is moved to skb it will not
be fragmented across skb's, so we can eliminate the sklist in the
audit_buffer. During audit_log_move, we simply copy the full buffer
into a single skb, and then audit_log_drain sends it on.
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
shutdown credential information. It creates a new message type
AUDIT_TERM_INFO, which is used by the audit daemon to query who issued the
shutdown.
It requires the placement of a hook function that gathers the information. The
hook is after the DAC & MAC checks and before the function returns. Racing
threads could overwrite the uid & pid - but they would have to be root and
have policy that allows signalling the audit daemon. That should be a
manageable risk.
The userspace component will be released later in audit 0.7.2. When it
receives the TERM signal, it queries the kernel for shutdown information.
When it receives it, it writes the message and exits. The message looks
like this:
type=DAEMON msg=auditd(1114551182.000) auditd normal halt, sending pid=2650
uid=525, auditd pid=1685
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As per http://www.nist.gov/dads/HTML/shellsort.html, this should be
referred to as a Shell sort. Shell-Metzner is a misnomer.
Signed-off-by: Daniel Dickman <didickman@yahoo.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It seems that the code responsible for this is in kernel/itimer.c:126:
p->signal->real_timer.expires = jiffies + interval;
add_timer(&p->signal->real_timer);
If you request an interval of, lets say 900 usecs, the interval given by
timeval_to_jiffies will be 1.
If you request this when we are half-way between two timer ticks, the
interval will only give 400 usecs.
If we want to guarantee that we never ever give intervals less than
requested, the simple solution would be to change that to:
p->signal->real_timer.expires = jiffies + interval + 1;
This however will produce pathological cases, like having a idle system
being requested 1 ms timeouts will give systematically 2 ms timeouts,
whereas currently it simply gives a few usecs less than 1 ms.
The complex (and more computationally expensive) solution would be to
check the gettimeofday time, and compute the correct number of jiffies.
This way, if we request a 300 usecs timer 200 usecs inside the timer
tick, we can wait just one tick, but not if we are 800 usecs inside the
tick. This would also mean that we would have to lock preemption during
these computations to avoid races, etc.
I've searched the archives but couldn't find this particular issue being
discussed before.
Attached is a patch to do the simple solution, in case anybody thinks
that it should be used.
Signed-Off-By: Paulo Marques <pmarques@grupopie.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow registration of multiple kprobes at an address in an architecture
agnostic way. Corresponding handlers will be invoked in a sequence. But,
a kprobe and a jprobe can't (yet) co-exist at the same address.
Signed-off-by: Ananth N Mavinakayanahalli <amavin@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kernel oops! when unregister_kprobe() is called on a non-registered
kprobe. This patch fixes the above problem by checking if the probe exists
before unregistering.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While looking at code generated by gcc4.0 I noticed some functions still
had frame pointers, even after we stopped ppc64 from defining
CONFIG_FRAME_POINTER. It turns out kernel/Makefile hardwires
-fno-omit-frame-pointer on when compiling schedule.c.
Create CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER and define it on architectures
that dont require frame pointers in sched.c code.
(akpm: blame me for the name)
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The PPC32 kernel puts platform-specific functions into separate sections so
that unneeded parts of it can be freed when we've booted and actually
worked out what we're running on today.
This makes kallsyms ignore those functions, because they're not between
_[se]text or _[se]inittext. Rather than teaching kallsyms about the
various pmac/chrp/etc sections, this patch adds '_[se]extratext' markers
for kallsyms.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Let's recap the problem. The current asynchronous netlink kernel
message processing is vulnerable to these attacks:
1) Hit and run: Attacker sends one or more messages and then exits
before they're processed. This may confuse/disable the next netlink
user that gets the netlink address of the attacker since it may
receive the responses to the attacker's messages.
Proposed solutions:
a) Synchronous processing.
b) Stream mode socket.
c) Restrict/prohibit binding.
2) Starvation: Because various netlink rcv functions were written
to not return until all messages have been processed on a socket,
it is possible for these functions to execute for an arbitrarily
long period of time. If this is successfully exploited it could
also be used to hold rtnl forever.
Proposed solutions:
a) Synchronous processing.
b) Stream mode socket.
Firstly let's cross off solution c). It only solves the first
problem and it has user-visible impacts. In particular, it'll
break user space applications that expect to bind or communicate
with specific netlink addresses (pid's).
So we're left with a choice of synchronous processing versus
SOCK_STREAM for netlink.
For the moment I'm sticking with the synchronous approach as
suggested by Alexey since it's simpler and I'd rather spend
my time working on other things.
However, it does have a number of deficiencies compared to the
stream mode solution:
1) User-space to user-space netlink communication is still vulnerable.
2) Inefficient use of resources. This is especially true for rtnetlink
since the lock is shared with other users such as networking drivers.
The latter could hold the rtnl while communicating with hardware which
causes the rtnetlink user to wait when it could be doing other things.
3) It is still possible to DoS all netlink users by flooding the kernel
netlink receive queue. The attacker simply fills the receive socket
with a single netlink message that fills up the entire queue. The
attacker then continues to call sendmsg with the same message in a loop.
Point 3) can be countered by retransmissions in user-space code, however
it is pretty messy.
In light of these problems (in particular, point 3), we should implement
stream mode netlink at some point. In the mean time, here is a patch
that implements synchronous processing.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch "MCA recovery improvements" added do_exit to mca_drv.c.
That's fine when the mca recovery code is built in the kernel
(CONFIG_IA64_MCA_RECOVERY=y) but breaks building the mca recovery
code as a module (CONFIG_IA64_MCA_RECOVERY=m).
Most users are currently building this as a module, as loading
and unloading the module provides a very convenient way to turn
on/off error recovery.
This patch exports do_exit, so mca_drv.c can build as a module.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
When adding more formatted audit data to an skb for delivery to userspace,
the kernel will attempt to reuse an skb that has spare room. However, if
the audit message has already been fragmented to multiple skb's, the search
for spare room in the skb uses the head of the list. This will corrupt the
audit message with trailing bytes being placed midway through the stream.
Fix is to look at the end of the list.
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Another large rollup of various patches from Adrian which make things static
where they were needlessly exported.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some KernelDoc descriptions are updated to match the current code.
No code changes.
Signed-off-by: Martin Waitz <tali@admingilde.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have recompiled Linux kernel 2.6.11.5 documentation for me and our
university students again. The documentation could be extended for more
sources which are equipped by structured comments for recent 2.6 kernels. I
have tried to proceed with that task. I have done that more times from 2.6.0
time and it gets boring to do same changes again and again. Linux kernel
compiles after changes for i386 and ARM targets. I have added references to
some more files into kernel-api book, I have added some section names as well.
So please, check that changes do not break something and that categories are
not too much skewed.
I have changed kernel-doc to accept "fastcall" and "asmlinkage" words reserved
by kernel convention. Most of the other changes are modifications in the
comments to make kernel-doc happy, accept some parameters description and do
not bail out on errors. Changed <pid> to @pid in the description, moved some
#ifdef before comments to correct function to comments bindings, etc.
You can see result of the modified documentation build at
http://cmp.felk.cvut.cz/~pisa/linux/lkdb-2.6.11.tar.gz
Some more sources are ready to be included into kernel-doc generated
documentation. Sources has been added into kernel-api for now. Some more
section names added and probably some more chaos introduced as result of quick
cleanup work.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Martin Waitz <tali@admingilde.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert most of the current code that uses _NSIG directly to instead use
valid_signal(). This avoids gcc -W warnings and off-by-one errors.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The synchronize_kernel() primitive is used for quite a few different purposes:
waiting for RCU readers, waiting for NMIs, waiting for interrupts, and so on.
This makes RCU code harder to read, since synchronize_kernel() might or might
not have matching rcu_read_lock()s. This patch creates a new
synchronize_rcu() that is to be used for RCU readers and a new
synchronize_sched() that is used for the rest. These two new primitives
currently have the same implementation, but this is might well change with
additional real-time support. Both new primitives are GPL-only, the old
primitive is deprecated.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The gpl exports need to be put back. Moving them to GPL -- but in a
measured manner, as I proposed on this list some months ago -- is fine.
Changing these particular exports precipitously is most definitely -not-
fine. Here is my earlier proposal:
http://marc.theaimsgroup.com/?l=linux-kernel&m=110520930301813&w=2
See below for a patch that puts the exports back, along with an updated
version of my earlier patch that starts the process of moving them to GPL.
I will also be following this message with RFC patches that introduce two
(EXPORT_SYMBOL_GPL) interfaces to replace synchronize_kernel(), which then
becomes deprecated.
Signed-off-by: <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arrange for all kernel printks to be no-ops. Only available if
CONFIG_EMBEDDED.
This patch saves about 375k on my laptop config and nearly 100k on minimal
configs.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a pair of rlimits for allowing non-root tasks to raise nice and rt
priorities. Defaults to traditional behavior. Originally written by
Chris Wright.
The patch implements a simple rlimit ceiling for the RT (and nice) priorities
a task can set. The rlimit defaults to 0, meaning no change in behavior by
default. A value of 50 means RT priority levels 1-50 are allowed. A value of
100 means all 99 privilege levels from 1 to 99 are allowed. CAP_SYS_NICE is
blanket permission.
(akpm: see http://www.uwsg.iu.edu/hypermail/linux/kernel/0503.1/1921.html for
tips on integrating this with PAM).
Signed-off-by: Matt Mackall <mpm@selenic.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace a number of memory barriers with smp_ variants. This means we won't
take the unnecessary hit on UP machines.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Attached is a new patch that solves the issue of getting valid credentials
into the LOGIN message. The current code was assuming that the audit context
had already been copied. This is not always the case for LOGIN messages.
To solve the problem, the patch passes the task struct to the function that
emits the message where it can get valid credentials.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If netlink_unicast() fails, requeue the skb back at the head of the queue
it just came from, instead of the tail. And do so unless we've exceeded
the audit_backlog limit; not according to some other arbitrary limit.
From: Chris Wright <chrisw@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Most audit control messages are sent over netlink.In order to properly
log the identity of the sender of audit control messages, we would like
to add the loginuid to the netlink_creds structure, as per the attached
patch.
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
They don't seem to work correctly (investigation ongoing), but we don't
actually need to do it anyway.
Patch from Peter Martuccelli <peterm@redhat.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Attached is a patch that corrects a signed/unsigned warning. I also noticed
that we needlessly init serial to 0. That only needs to occur if the kernel
was compiled without the audit system.
-Steve Grubb
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We were calling ptrace_notify() after auditing the syscall and arguments,
but the debugger could have _changed_ them before the syscall was actually
invoked. Reorder the calls to fix that.
While we're touching ever call to audit_syscall_entry(), we also make it
take an extra argument: the architecture of the syscall which was made,
because some architectures allow more than one type of syscall.
Also add an explicit success/failure flag to audit_syscall_exit(), for
the benefit of architectures which return that in a condition register
rather than only returning a single register.
Change type of syscall return value to 'long' not 'int'.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
kernel/audit.c: In function `audit_log_untrustedstring':
kernel/audit.c:736: warning: comparison is always false due to limited range of data type
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We log strings from userspace, such as arguments to open(). These could
be formatted to contain \n followed by fake audit log entries. Provide
a function for logging such strings, which gives a hex dump when the
string contains anything but basic printable ASCII characters. Use it
for logging filenames.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
settimeofday will set the time a little bit too early on systems using
time interpolation since it subtracts the current interpolator offset
from the time. This used to be necessary with the code in 2.6.9 and earlier
but the new code resets the time interpolator after setting the time.
Thus the time is set too early and gettimeofday will return a time slightly
before the time specified with settimeofday if invoked immeditely after
settimeofday.
This removes the obsolete subtraction of the time interpolator offset
and makes settimeofday set the time accurately.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is incredibly trivial, but it does resolve some of the user
confusion as to what "L1-A" actually is.
Clarify printk message to refer to Stop-A (L1-A).
Gentoo has a virtually identical patch in their kernel sources.
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a deadlock on the dcache lock detected during testing at IBM
by moving the logging of the current executable information from the
SELinux avc_audit function to audit_log_exit (via an audit_log_task_info
helper) for processing upon syscall exit.
For consistency, the patch also removes the logging of other
task-related information from avc_audit, deferring handling to
audit_log_exit instead.
This allows simplification of the avc_audit code, allows the exe
information to be obtained more reliably, always includes the comm
information (useful for scripts), and avoids including bogus task
information for checks performed from irq or softirq.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch hides reparent_to_init(). reparent_to_init() should only be
called by daemonize().
Signed-off-by: Coywolf Qi Hunt <coywolf@lovecn.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
gcc-4 warns with
include/linux/cpuset.h:21: warning: type qualifiers ignored on function
return type
cpuset_cpus_allowed is declared with const
extern const cpumask_t cpuset_cpus_allowed(const struct task_struct *p);
First const should be __attribute__((const)), but the gcc manual
explains that:
"Note that a function that has pointer arguments and examines the data
pointed to must not be declared const. Likewise, a function that calls a
non-const function usually must not be const. It does not make sense for
a const function to return void."
The following patch remove const from the function declaration.
Signed-off-by: Benoit Boissinot <benoit.boissinot@ens-lyon.org>
Acked-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IXP2000 (ARM-based) platforms use a separate 'struct resource' for PCI MEM
space. Resource allocation for PCI BARs always fails because the 'root'
resource (the IXP2000 PCI MEM resource) always has the entire address space
(00000000-ffffffff) free, and find_resource() calculates the size of that
range as ffffffff-00000000+1=0, so all allocations fail because it thinks
there is no space.
(akpm: pls. double-check)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that no architectures defines HAVE_ARCH_GET_SIGNAL_TO_DELIVER anymore
this can go away. It was a transitional hack only.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
there seems to be a bug, at least for me, in kernel/param.c for arrays with
.num == NULL. If .num == NULL, the function param_array_set() uses &.max
for the call to param_array(), wich alters the .max value to the number of
arguments. The result is, you can't set more array arguments as the last
time you set the parameter.
example:
# a module 'example' with
# static int array[10] = { 0, };
# module_param_array(array, int, NULL, 0644);
$ insmod example.ko array=1,2,3
$ cat /sys/module/example/parameters/array
1,2,3
$ echo "4,3,2,1" > /sys/module/example/parameters/array
$ dmesg | tail -n 1
kernel: array: can take only 3 arguments
Signed-off-by: Bert Wesarg <wesarg@informatik.uni-halle.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have no idea how a bug like this lasted so long. Anyways, obvious
memset()'ing of incorrect pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was unexported by Arjan because we have no current users.
However, during a conversion from tasklets to workqueues of the parisc led
functions, we ran across a case where this was needed. In particular, the
open coded equivalent of cancel_rearming_delayed_workqueue was implemented
incorrectly, which is, I think, all the evidence necessary that this is a
useful API.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
