- Fix corner-case suspend-to-idle wakeup issue on systems where
the ACPI SCI is shared with another wakeup source (Hans de Goede).
- Add document describing system-wide suspend and resume code flows
to the admin guide (Rafael Wysocki).
- Add kernel command line option to set pm_debug_messages (Chen Yu).
- Choose schedutil as the preferred scaling governor by default on
ARM big.LITTLE systems and on x86 systems using the intel_pstate
driver in the passive mode (Linus Walleij, Rafael Wysocki).
- Drop racy and redundant checks from the PM core's device_prepare()
routine (Rafael Wysocki).
- Make resume from hibernation take the hibernation_restore() return
value into account (Dexuan Cui).
-----BEGIN PGP SIGNATURE-----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=QFDr
-----END PGP SIGNATURE-----
Merge tag 'pm-5.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"Additional power management updates.
These fix a corner-case suspend-to-idle wakeup issue on systems where
the ACPI SCI is shared with another wakeup source, add a kernel
command line option to set pm_debug_messages via the kernel command
line, add a document desctibing system-wide suspend and resume code
flows, modify cpufreq Kconfig to choose schedutil as the preferred
governor by default in a couple of cases and do some assorted
cleanups.
Specifics:
- Fix corner-case suspend-to-idle wakeup issue on systems where the
ACPI SCI is shared with another wakeup source (Hans de Goede).
- Add document describing system-wide suspend and resume code flows
to the admin guide (Rafael Wysocki).
- Add kernel command line option to set pm_debug_messages (Chen Yu).
- Choose schedutil as the preferred scaling governor by default on
ARM big.LITTLE systems and on x86 systems using the intel_pstate
driver in the passive mode (Linus Walleij, Rafael Wysocki).
- Drop racy and redundant checks from the PM core's device_prepare()
routine (Rafael Wysocki).
- Make resume from hibernation take the hibernation_restore() return
value into account (Dexuan Cui)"
* tag 'pm-5.7-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
platform/x86: intel_int0002_vgpio: Use acpi_register_wakeup_handler()
ACPI: PM: Add acpi_[un]register_wakeup_handler()
Documentation: PM: sleep: Document system-wide suspend code flows
cpufreq: Select schedutil when using big.LITTLE
PM: sleep: Add pm_debug_messages kernel command line option
PM: sleep: core: Drop racy and redundant checks from device_prepare()
PM: hibernate: Propagate the return value of hibernation_restore()
cpufreq: intel_pstate: Select schedutil as the default governor
Alan Stern points out that the WARN_ON() check in device_prepare()
is racy (because the PM-runtime API can be disabled briefly for any
device at any time and system suspend can start at any time too) and
the pm_runtime_suspended() check in the computation of the
direct_complete flag value is redundant (because it will be
repeated later anyway).
Drop both these checks accordingly.
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
Skip wakeup_source_sysfs_remove() to fix a NULL pinter dereference via
ws->dev, if the wakeup source is unregistered before registering the
wakeup class from device_add().
Fixes: 2ca3d1ecb8 ("PM / wakeup: Register wakeup class kobj after device is added")
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Cc: 5.4+ <stable@vger.kernel.org> # 5.4+
[ rjw: Subject & changelog, white space ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 2c36168480 ("PM / Domains: Don't treat zero found compatible idle
states as an error"), moved of_genpd_parse_idle_states() towards allowing
none compatible idle state to be found for the device node, rather than
returning an error code.
However, it didn't consider that the "domain-idle-states" DT property may
be missing as it's optional, which makes of_count_phandle_with_args() to
return -ENOENT. Let's fix this to make the behaviour consistent.
Fixes: 2c36168480 ("PM / Domains: Don't treat zero found compatible idle states as an error")
Reported-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Cc: 4.20+ <stable@vger.kernel.org> # 4.20+
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
pm_runtime_get_if_in_use() bumps up the PM-runtime usage count if it
is not equal to zero and the device's PM-runtime status is 'active'.
This works for drivers that do not use autoidle, but for those that
do, the function returns zero even when the device is active.
In order to maintain sane device state while the device is powered on
in the hope that it'll be needed, pm_runtime_get_if_active(dev, true)
returns a positive value if the device's PM-runtime status is 'active'
when it is called, in which case it also increments the device's usage
count.
If the second argument of pm_runtime_get_if_active() is 'false', the
function behaves just like pm_runtime_get_if_in_use(), so redefine
the latter as a wrapper around the former.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a helper to change the owner of a device's power entries. This
needs to happen when the ownership of a device is changed, e.g. when
moving network devices between network namespaces.
This function will be used to correctly account for ownership changes,
e.g. when moving network devices between network namespaces.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: "Rafael J. Wysocki" <rafael@kernel.org>
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller pieces
for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
+ Misc cleanups, refactorings of Marvell, TI, other platforms.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAl4+lTYPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3nQcQAJm91+6hZbmMjlBySGS7ISjYvOcrI/hMgiOl
uhhEP0Dcylvf9A9x3wcIbLwixe+2pvie9DQh2u5F80ShYimidtFi/2xCfuTb9fKu
sxxKjrXWyVKhkpW0z+tedY08ftVhkwwcyD4m2C7uVl6AwTP7c367vFeU7XjF2APn
drfgmgbjm8U3XbSyAqv+k6z6tyqaCnFM7vbPupSKHgHJ3mfByxOa+XyBN2RdgBbs
0KrVfbXGv80zFIFrMPwaWG7G52bu7K68nVdgy44MpKdRZ6QTjhnR+kerFxHsYgV4
bM55Fya52nTCSTGdKaQakDtKwbAUdCDTSkxgOHGcQoyFi0R/VaEUJtcysnvLbI6c
+n/yFIzGyEdXcvIzfv2SoDYhogw19I6RR/M9K5Ni29eazkDVYx2z3rI+2QYeqCiF
u7cq52gW6JLP0SI/9kuUrRFiR8v19Ixap7qokAxgqQwYB3NzT8a7WsYPkzdpDZGQ
ETSDFMyBWT6UvBe/HWkQluBabbet53rG8BF0OHFrQuMK0u/ieKgSGuTB9XN2djEW
PHMOMz2vhi+8XTfpkskhF2tTxlA/k4R6QwCdIMpIkMRVnVQCh1XdPr3Fi2NrgB+S
kIXHD4vV6zLYh04zHyKewSPHAXWgraFpg2qKnvL5+KWMTnW6QH+RNjOt9xKDNXOd
+iDXpOad
=ONtb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
Prevent cpufreq from creating excessively large stack frames and fix
the handling of devices deleted during system-wide resume in the PM
core (Rafael Wysocki), revert a problematic commit affecting the
cpupower utility and correct its man page (Thomas Renninger,
Brahadambal Srinivasan), and improve the intel_pstate_tracer
utility (Doug Smythies).
-----BEGIN PGP SIGNATURE-----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=ctQq
-----END PGP SIGNATURE-----
Merge tag 'pm-5.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power manadement updates from Rafael Wysocki:
"Prevent cpufreq from creating excessively large stack frames and fix
the handling of devices deleted during system-wide resume in the PM
core (Rafael Wysocki), revert a problematic commit affecting the
cpupower utility and correct its man page (Thomas Renninger,
Brahadambal Srinivasan), and improve the intel_pstate_tracer utility
(Doug Smythies)"
* tag 'pm-5.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tools/power/x86/intel_pstate_tracer: change several graphs to autoscale y-axis
tools/power/x86/intel_pstate_tracer: changes for python 3 compatibility
Correction to manpage of cpupower
cpufreq: Avoid creating excessively large stack frames
PM: core: Fix handling of devices deleted during system-wide resume
cpupower: Revert library ABI changes from commit ae2917093f
This kunit update for Linux 5.6-rc1 consists of:
-- Support for building kunit as a module from Alan Maguire
-- AppArmor KUnit tests for policy unpack from Mike Salvatore
-----BEGIN PGP SIGNATURE-----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=AFO4
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.6-rc1-kunit' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest kunit updates from Shuah Khan:
"This kunit update consists of:
- Support for building kunit as a module from Alan Maguire
- AppArmor KUnit tests for policy unpack from Mike Salvatore"
* tag 'linux-kselftest-5.6-rc1-kunit' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
kunit: building kunit as a module breaks allmodconfig
kunit: update documentation to describe module-based build
kunit: allow kunit to be loaded as a module
kunit: remove timeout dependence on sysctl_hung_task_timeout_seconds
kunit: allow kunit tests to be loaded as a module
kunit: hide unexported try-catch interface in try-catch-impl.h
kunit: move string-stream.h to lib/kunit
apparmor: add AppArmor KUnit tests for policy unpack
* pm-core:
PM-runtime: add tracepoints for usage_count changes
* powercap:
powercap/intel_rapl: add support for JasperLake
x86/cpu: Add Jasper Lake to Intel family
powercap/intel_rapl: add support for TigerLake Mobile
* pm-opp:
opp: Replace list_kref with a local counter
opp: Free static OPPs on errors while adding them
* pm-avs:
power: avs: qcom-cpr: remove duplicated include from qcom-cpr.c
power: avs: fix uninitialized error return on failed cpr_read_fuse_uV() call
power: avs: qcom-cpr: make cpr_get_opp_hz_for_req() static
power: avs: qcom-cpr: remove set but unused variable
power: avs: qcom-cpr: make sure that regmap is available
power: avs: qcom-cpr: fix unsigned expression compared with zero
power: avs: qcom-cpr: fix invalid printk specifier in debug print
power: avs: Add support for CPR (Core Power Reduction)
dt-bindings: power: avs: Add support for CPR (Core Power Reduction)
* pm-misc:
mailmap: Add entry for <rjw@sisk.pl>
If a device is deleted by one of its system-wide resume callbacks
(for example, because it does not appear to be present or accessible
any more) along with its children, the resume of the children may
continue leading to use-after-free errors and other issues
(potentially).
Namely, if the device's children are resumed asynchronously, their
resume may have been scheduled already before the device's callback
runs and so the device may be deleted while dpm_wait_for_superior()
is being executed for them. The memory taken up by the parent device
object may be freed then while dpm_wait() is waiting for the parent's
resume callback to complete, which leads to a use-after-free.
Moreover, the resume of the children is really not expected to
continue after they have been unregistered, so it must be terminated
right away in that case.
To address this problem, modify dpm_wait_for_superior() to check
if the target device is still there in the system-wide PM list of
devices and if so, to increment its parent's reference counter, both
under dpm_list_mtx which prevents device_del() running for the child
from dropping the parent's reference counter prematurely.
If the device is not present in the system-wide PM list of devices
any more, the resume of it cannot continue, so check that again after
dpm_wait() returns, which means that the parent's callback has been
completed, and pass the result of that check to the caller of
dpm_wait_for_superior() to allow it to abort the device's resume
if it is not there any more.
Link: https://lore.kernel.org/linux-pm/1579568452-27253-1-git-send-email-chanho.min@lge.com
Reported-by: Chanho Min <chanho.min@lge.com>
Cc: All applicable <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add tracepoints to remaining places where device's power.usage_count
is changed.
This helps debugging where and why autosuspend is prevented.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As tests are added to kunit, it will become less feasible to execute
all built tests together. By supporting modular tests we provide
a simple way to do selective execution on a running system; specifying
CONFIG_KUNIT=y
CONFIG_KUNIT_EXAMPLE_TEST=m
...means we can simply "insmod example-test.ko" to run the tests.
To achieve this we need to do the following:
o export the required symbols in kunit
o string-stream tests utilize non-exported symbols so for now we skip
building them when CONFIG_KUNIT_TEST=m.
o drivers/base/power/qos-test.c contains a few unexported interface
references, namely freq_qos_read_value() and freq_constraints_init().
Both of these could be potentially defined as static inline functions
in include/linux/pm_qos.h, but for now we simply avoid supporting
module build for that test suite.
o support a new way of declaring test suites. Because a module cannot
do multiple late_initcall()s, we provide a kunit_test_suites() macro
to declare multiple suites within the same module at once.
o some test module names would have been too general ("test-test"
and "example-test" for kunit tests, "inode-test" for ext4 tests);
rename these as appropriate ("kunit-test", "kunit-example-test"
and "ext4-inode-test" respectively).
Also define kunit_test_suite() via kunit_test_suites()
as callers in other trees may need the old definition.
Co-developed-by: Knut Omang <knut.omang@oracle.com>
Signed-off-by: Knut Omang <knut.omang@oracle.com>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Theodore Ts'o <tytso@mit.edu> # for ext4 bits
Acked-by: David Gow <davidgow@google.com> # For list-test
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
We already have the of_genpd_add_subdomain() helper, but no corresponding
of_genpd_remove_subdomain(), so let's add it. Subsequent changes starts to
make use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
After commit 00ee22c289 (PM / wakeup: Use seq_open() to show wakeup
stats), print_wakeup_source_stats(m, &deleted_ws) is not called from
wakeup_sources_stats_seq_show() any more.
Because deleted_ws is one of the wakeup sources, it should be shown
too, so add it to the end of all other wakeup sources.
Signed-off-by: zhuguangqing <zhuguangqing@xiaomi.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo
-----BEGIN PGP SIGNATURE-----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=dk7w
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Support for adding per-device frequency limits was removed in
commit 2aac8bdf7a ("PM: QoS: Drop frequency QoS types from device PM QoS")
after cpufreq switched to use a new "freq_constraints" construct.
Restore support for per-device freq limits but base this upon
freq_constraints. This is primarily meant to be used by the devfreq
subsystem.
This removes the "static" marking on freq_qos_apply but does not export
it for modules.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The pm_qos family of APIs are used in relatively difficult to reproduce
scenarios such as thermal throttling so they benefit from unit testing.
Start by adding basic tests from the the freq_qos APIs. It includes
tests for issues that were brought up on mailing lists:
https://patchwork.kernel.org/patch/11252425/#23017005https://patchwork.kernel.org/patch/11253421/
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-sleep:
PM / wakeirq: remove unnecessary parentheses
PM / core: Clean up some function headers in power.h
PM / hibernate: memory_bm_find_bit(): Tighten node optimisation
* pm-domains:
PM / Domains: Convert to dev_to_genpd_safe() in genpd_syscore_switch()
mmc: tmio: Avoid boilerplate code in ->runtime_suspend()
PM / Domains: Implement the ->start() callback for genpd
PM / Domains: Introduce dev_pm_domain_start()
* pm-opp:
PM / OPP: Support adjusting OPP voltages at runtime
* powercap:
powercap/intel_rapl: add support for Cometlake desktop
powercap/intel_rapl: add support for CometLake Mobile
The intent with walking the gpd_list via calling genpd_present() from
genpd_syscore_switch(), is to make sure the dev->pm_domain pointer belongs
to a registered genpd. However, as a genpd can't be removed if there is a
device attached to it, let's convert to use the quicker dev_to_genpd_safe()
instead.
Due to the above change, this allows us to clean up genpd_present() and
move it inside CONFIG_PM_GENERIC_DOMAINS_OF, so let's do that as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
To allow a subsystem/driver to explicitly start its device from genpd's
point view, let's implement the ->start() callback in the struct
dev_pm_domain that corresponds to the genpd.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For a subsystem/driver that either doesn't support runtime PM or makes use
of pm_runtime_set_active() during ->probe(), may try to access its device
when probing, even if it may not be fully powered on from the PM domain's
point of view. This may be the case when the used PM domain is a genpd
provider, that implements genpd's ->start|stop() device callbacks.
There are cases where the subsystem/driver managed to avoid the above
problem, simply by calling pm_runtime_enable() and pm_runtime_get_sync()
during ->probe(). However, this approach comes with a drawback, especially
if the subsystem/driver implements a ->runtime_resume() callback.
More precisely, the subsystem/driver then needs to use a device flag, which
is checked in its ->runtime_resume() callback, as to avoid powering on its
resources the first time the callback is invoked. This is needed because
the subsystem/driver has already powered on the resources for the device,
during ->probe() and before it called pm_runtime_get_sync().
In a way to avoid this boilerplate code and the inefficient check for "if
(first_time_suspend)" in the ->runtime_resume() callback for these
subsystems/drivers, let's introduce and export a dev_pm_domain_start()
function, that may be called during ->probe() instead.
Moreover, let the dev_pm_domain_start() invoke an optional ->start()
callback, added to the struct dev_pm_domain, as to allow a PM domain
specific implementation.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove unnecessary parentheses found by code review.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The power.h is a bit messy due to the various existing CONFIG_PM* Kconfig
combinations. However the final section for wakeup_source_sysfs*() can be
moved inside one of the existing sections rather than adding yet another
one, so let's do that to clean up the code a little bit.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some user might want to go through all registered wakeup sources
and doing things accordingly. For example, SoC PM driver might need to
do HW programming to prevent powering down specific IP which wakeup
source depending on. So add this API to help walk through all registered
wakeup source objects on that list and return them one by one.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
There are no more active users of DEV_PM_QOS_MIN_FREQUENCY and
DEV_PM_QOS_MAX_FREQUENCY device PM QoS request types, so drop them
along with the code supporting them.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Here is the big driver core update for 5.4-rc1.
There was a bit of a churn in here, with a number of core and OF
platform patches being added to the tree, and then after much discussion
and review and a day-long in-person meeting, they were decided to be
reverted and a new set of patches is currently being reviewed on the
mailing list.
Other than that churn, there are two "persistent" branches in here that
other trees will be pulling in as well during the merge window. One
branch to add support for drivers to have the driver core automatically
add sysfs attribute files when a driver is bound to a device so that the
driver doesn't have to manually do it (and then clean it up, as it
always gets it wrong).
There's another branch in here for generic lookup helpers for the driver
core that lots of busses are starting to use. That's the majority of
the non-driver-core changes in this patch series.
There's also some on-going debugfs file creation cleanup that has been
slowly happening over the past few releases, with the goal to hopefully
get that done sometime next year.
All of these have been in linux-next for a while now with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXYIVHA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymEVwCfRPxQHQplI6ZR6h0jPscLSaZnaFIAn1a+rjO2
EFuuXJ5Ip72F5Ch9AW3G
=r8lH
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here is the big driver core update for 5.4-rc1.
There was a bit of a churn in here, with a number of core and OF
platform patches being added to the tree, and then after much
discussion and review and a day-long in-person meeting, they were
decided to be reverted and a new set of patches is currently being
reviewed on the mailing list.
Other than that churn, there are two "persistent" branches in here
that other trees will be pulling in as well during the merge window.
One branch to add support for drivers to have the driver core
automatically add sysfs attribute files when a driver is bound to a
device so that the driver doesn't have to manually do it (and then
clean it up, as it always gets it wrong).
There's another branch in here for generic lookup helpers for the
driver core that lots of busses are starting to use. That's the
majority of the non-driver-core changes in this patch series.
There's also some on-going debugfs file creation cleanup that has been
slowly happening over the past few releases, with the goal to
hopefully get that done sometime next year.
All of these have been in linux-next for a while now with no reported
issues"
[ Note that the above-mentioned generic lookup helpers branch was
already brought in by the LED merge (commit 4feaab05dc) that had
shared it.
Also note that that common branch introduced an i2c bug due to a bad
conversion, which got fixed here. - Linus ]
* tag 'driver-core-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (49 commits)
coccinelle: platform_get_irq: Fix parse error
driver-core: add include guard to linux/container.h
sysfs: add BIN_ATTR_WO() macro
driver core: platform: Export platform_get_irq_optional()
hwmon: pwm-fan: Use platform_get_irq_optional()
driver core: platform: Introduce platform_get_irq_optional()
Revert "driver core: Add support for linking devices during device addition"
Revert "driver core: Add edit_links() callback for drivers"
Revert "of/platform: Add functional dependency link from DT bindings"
Revert "driver core: Add sync_state driver/bus callback"
Revert "of/platform: Pause/resume sync state during init and of_platform_populate()"
Revert "of/platform: Create device links for all child-supplier depencencies"
Revert "of/platform: Don't create device links for default busses"
Revert "of/platform: Fix fn definitons for of_link_is_valid() and of_link_property()"
Revert "of/platform: Fix device_links_supplier_sync_state_resume() warning"
Revert "of/platform: Disable generic device linking code for PowerPC"
devcoredump: fix typo in comment
devcoredump: use memory_read_from_buffer
of/platform: Disable generic device linking code for PowerPC
device.h: Fix warnings for mismatched parameter names in comments
...
- Rework the main suspend-to-idle control flow to avoid repeating
"noirq" device resume and suspend operations in case of spurious
wakeups from the ACPI EC and decouple the ACPI EC wakeups support
from the LPS0 _DSM support (Rafael Wysocki).
- Extend the wakeup sources framework to expose wakeup sources as
device objects in sysfs (Tri Vo, Stephen Boyd).
- Expose system suspend statistics in sysfs (Kalesh Singh).
- Introduce a new haltpoll cpuidle driver and a new matching
governor for virtualized guests wanting to do guest-side polling
in the idle loop (Marcelo Tosatti, Joao Martins, Wanpeng Li,
Stephen Rothwell).
- Fix the menu and teo cpuidle governors to allow the scheduler tick
to be stopped if PM QoS is used to limit the CPU idle state exit
latency in some cases (Rafael Wysocki).
- Increase the resolution of the play_idle() argument to microseconds
for more fine-grained injection of CPU idle cycles (Daniel Lezcano).
- Switch over some users of cpuidle notifiers to the new QoS-based
frequency limits and drop the CPUFREQ_ADJUST and CPUFREQ_NOTIFY
policy notifier events (Viresh Kumar).
- Add new cpufreq driver based on nvmem for sun50i (Yangtao Li).
- Add support for MT8183 and MT8516 to the mediatek cpufreq driver
(Andrew-sh.Cheng, Fabien Parent).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
- Add qcs404 to cpufreq-dt-platdev blacklist (Jorge Ramirez-Ortiz).
- Update the qcom cpufreq driver (among other things, to make it
easier to extend and to use kryo cpufreq for other nvmem-based
SoCs) and add qcs404 support to it (Niklas Cassel, Douglas
RAILLARD, Sibi Sankar, Sricharan R).
- Fix assorted issues and make assorted minor improvements in the
cpufreq code (Colin Ian King, Douglas RAILLARD, Florian Fainelli,
Gustavo Silva, Hariprasad Kelam).
- Add new devfreq driver for NVidia Tegra20 (Dmitry Osipenko, Arnd
Bergmann).
- Add new Exynos PPMU events to devfreq events and extend that
mechanism (Lukasz Luba).
- Fix and clean up the exynos-bus devfreq driver (Kamil Konieczny).
- Improve devfreq documentation and governor code, fix spelling
typos in devfreq (Ezequiel Garcia, Krzysztof Kozlowski, Leonard
Crestez, MyungJoo Ham, Gaël PORTAY).
- Add regulators enable and disable to the OPP (operating performance
points) framework (Kamil Konieczny).
- Update the OPP framework to support multiple opp-suspend properties
(Anson Huang).
- Fix assorted issues and make assorted minor improvements in the OPP
code (Niklas Cassel, Viresh Kumar, Yue Hu).
- Clean up the generic power domains (genpd) framework (Ulf Hansson).
- Clean up assorted pieces of power management code and documentation
(Akinobu Mita, Amit Kucheria, Chuhong Yuan).
- Update the pm-graph tool to version 5.5 including multiple fixes
and improvements (Todd Brandt).
- Update the cpupower utility (Benjamin Weis, Geert Uytterhoeven,
Sébastien Szymanski).
-----BEGIN PGP SIGNATURE-----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=TBDQ
-----END PGP SIGNATURE-----
Merge tag 'pm-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a rework of the main suspend-to-idle code flow (related
to the handling of spurious wakeups), a switch over of several users
of cpufreq notifiers to QoS-based limits, a new devfreq driver for
Tegra20, a new cpuidle driver and governor for virtualized guests, an
extension of the wakeup sources framework to expose wakeup sources as
device objects in sysfs, and more.
Specifics:
- Rework the main suspend-to-idle control flow to avoid repeating
"noirq" device resume and suspend operations in case of spurious
wakeups from the ACPI EC and decouple the ACPI EC wakeups support
from the LPS0 _DSM support (Rafael Wysocki).
- Extend the wakeup sources framework to expose wakeup sources as
device objects in sysfs (Tri Vo, Stephen Boyd).
- Expose system suspend statistics in sysfs (Kalesh Singh).
- Introduce a new haltpoll cpuidle driver and a new matching governor
for virtualized guests wanting to do guest-side polling in the idle
loop (Marcelo Tosatti, Joao Martins, Wanpeng Li, Stephen Rothwell).
- Fix the menu and teo cpuidle governors to allow the scheduler tick
to be stopped if PM QoS is used to limit the CPU idle state exit
latency in some cases (Rafael Wysocki).
- Increase the resolution of the play_idle() argument to microseconds
for more fine-grained injection of CPU idle cycles (Daniel
Lezcano).
- Switch over some users of cpuidle notifiers to the new QoS-based
frequency limits and drop the CPUFREQ_ADJUST and CPUFREQ_NOTIFY
policy notifier events (Viresh Kumar).
- Add new cpufreq driver based on nvmem for sun50i (Yangtao Li).
- Add support for MT8183 and MT8516 to the mediatek cpufreq driver
(Andrew-sh.Cheng, Fabien Parent).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
- Add qcs404 to cpufreq-dt-platdev blacklist (Jorge Ramirez-Ortiz).
- Update the qcom cpufreq driver (among other things, to make it
easier to extend and to use kryo cpufreq for other nvmem-based
SoCs) and add qcs404 support to it (Niklas Cassel, Douglas
RAILLARD, Sibi Sankar, Sricharan R).
- Fix assorted issues and make assorted minor improvements in the
cpufreq code (Colin Ian King, Douglas RAILLARD, Florian Fainelli,
Gustavo Silva, Hariprasad Kelam).
- Add new devfreq driver for NVidia Tegra20 (Dmitry Osipenko, Arnd
Bergmann).
- Add new Exynos PPMU events to devfreq events and extend that
mechanism (Lukasz Luba).
- Fix and clean up the exynos-bus devfreq driver (Kamil Konieczny).
- Improve devfreq documentation and governor code, fix spelling typos
in devfreq (Ezequiel Garcia, Krzysztof Kozlowski, Leonard Crestez,
MyungJoo Ham, Gaël PORTAY).
- Add regulators enable and disable to the OPP (operating performance
points) framework (Kamil Konieczny).
- Update the OPP framework to support multiple opp-suspend properties
(Anson Huang).
- Fix assorted issues and make assorted minor improvements in the OPP
code (Niklas Cassel, Viresh Kumar, Yue Hu).
- Clean up the generic power domains (genpd) framework (Ulf Hansson).
- Clean up assorted pieces of power management code and documentation
(Akinobu Mita, Amit Kucheria, Chuhong Yuan).
- Update the pm-graph tool to version 5.5 including multiple fixes
and improvements (Todd Brandt).
- Update the cpupower utility (Benjamin Weis, Geert Uytterhoeven,
Sébastien Szymanski)"
* tag 'pm-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (126 commits)
cpuidle-haltpoll: Enable kvm guest polling when dedicated physical CPUs are available
cpuidle-haltpoll: do not set an owner to allow modunload
cpuidle-haltpoll: return -ENODEV on modinit failure
cpuidle-haltpoll: set haltpoll as preferred governor
cpuidle: allow governor switch on cpuidle_register_driver()
PM: runtime: Documentation: add runtime_status ABI document
pm-graph: make setVal unbuffered again for python2 and python3
powercap: idle_inject: Use higher resolution for idle injection
cpuidle: play_idle: Increase the resolution to usec
cpuidle-haltpoll: vcpu hotplug support
cpufreq: Add qcs404 to cpufreq-dt-platdev blacklist
cpufreq: qcom: Add support for qcs404 on nvmem driver
cpufreq: qcom: Refactor the driver to make it easier to extend
cpufreq: qcom: Re-organise kryo cpufreq to use it for other nvmem based qcom socs
dt-bindings: opp: Add qcom-opp bindings with properties needed for CPR
dt-bindings: opp: qcom-nvmem: Support pstates provided by a power domain
Documentation: cpufreq: Update policy notifier documentation
cpufreq: Remove CPUFREQ_ADJUST and CPUFREQ_NOTIFY policy notifier events
PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state()
PM / Domains: Simplify genpd_lookup_dev()
...
* pm-opp:
PM / OPP: Correct Documentation about library location
opp: of: Support multiple suspend OPPs defined in DT
dt-bindings: opp: Support multiple opp-suspend properties
opp: core: add regulators enable and disable
opp: Don't decrement uninitialized list_kref
* pm-qos:
PM: QoS: Get rid of unused flags
* acpi-pm:
ACPI: PM: Print debug messages on device power state changes
* pm-domains:
PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state()
PM / Domains: Simplify genpd_lookup_dev()
PM / Domains: Align in-parameter names for some genpd functions
* pm-tools:
pm-graph: make setVal unbuffered again for python2 and python3
cpupower: update German translation
tools/power/cpupower: fix 64bit detection when cross-compiling
cpupower: Add missing newline at end of file
pm-graph v5.5
* pm-s2idle-rework: (21 commits)
ACPI: PM: s2idle: Always set up EC GPE for system wakeup
ACPI: PM: s2idle: Avoid rearming SCI for wakeup unnecessarily
PM: suspend: Fix platform_suspend_prepare_noirq()
intel-hid: Disable button array during suspend-to-idle
intel-hid: intel-vbtn: Avoid leaking wakeup_mode set
ACPI: PM: s2idle: Execute LPS0 _DSM functions with suspended devices
ACPI: EC: PM: Make acpi_ec_dispatch_gpe() print debug message
ACPI: EC: PM: Consolidate some code depending on PM_SLEEP
ACPI: PM: s2idle: Eliminate acpi_sleep_no_ec_events()
ACPI: PM: s2idle: Switch EC over to polling during "noirq" suspend
ACPI: PM: s2idle: Add acpi.sleep_no_lps0 module parameter
ACPI: PM: s2idle: Rearrange lps0_device_attach()
ACPI: PM: Set up EC GPE for system wakeup from drivers that need it
PM: sleep: Drop dpm_noirq_begin() and dpm_noirq_end()
PM: sleep: Integrate suspend-to-idle with generig suspend flow
PM: sleep: Simplify suspend-to-idle control flow
ACPI: PM: Set s2idle_wakeup earlier and clear it later
PM: sleep: Fix possible overflow in pm_system_cancel_wakeup()
ACPI: EC: Return bool from acpi_ec_dispatch_gpe()
ACPICA: Return u32 from acpi_dispatch_gpe()
...
The dev_pm_genpd_set_performance_state() could in principle be called for a
device that has a different PM domain type attached than a genpd. This
would lead to a problem as dev_to_genpd() uses the container_of macro.
Address this problem by using dev_to_genpd_safe() instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
genpd_lookup_dev(), is a bit unnecessary heavy, as it walks the gpd_list to
try to find a valid PM domain corresponding to the device's attached genpd.
Instead of walking the gpd_list, let's use the fact that a genpd always has
the ->runtime_suspend() callback assigned to the genpd_runtime_suspend()
function.
While changing this, let's take the opportunity to also rename
genpd_lookup_dev(), into dev_to_genpd_safe() to better reflect its purpose.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These functions are just used by the PM core, and that isn't modular so
these functions don't need to be exported. Drop the exports.
Fixes: c8377adfa7 ("PM / wakeup: Show wakeup sources stats in sysfs")
Reviewed-by: Tri Vo <trong@android.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The device_set_wakeup_enable() function can be called on a device that
hasn't been registered with device_add() yet. This allows the device to
be in a state where wakeup is enabled for it but the device isn't
published to userspace in sysfs yet.
After commit c8377adfa7 ("PM / wakeup: Show wakeup sources stats in
sysfs"), calling device_set_wakeup_enable() will fail for a device that
hasn't been registered with the driver core via device_add(). This is
because we try to create sysfs entries for the device and associate a
wakeup class kobject with it before the device has been registered.
Let's follow a similar approach that device_set_wakeup_capable() takes
here and register the wakeup class either from
device_set_wakeup_enable() when the device is already registered, or
from dpm_sysfs_add() when the device is being registered with the driver
core via device_add().
Fixes: c8377adfa7 ("PM / wakeup: Show wakeup sources stats in sysfs")
Reported-by: Qian Cai <cai@lca.pw>
Reviewed-by: Tri Vo <trong@android.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We shouldn't call wakeup_source_destroy() from the error path in
wakeup_source_register() because that calls __pm_relax() which takes a
lock that isn't initialized until wakeup_source_add() is called. Add a
new function, wakeup_source_free(), that just does the bare minimum to
free a wakeup source that was created but hasn't been added yet and use
it from the two places it's needed. This fixes the following problem
seen on various x86 server boxes:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 12 PID: 1 Comm: swapper/0 Not tainted 5.3.0-rc4-
Hardware name: HP ProLiant XL420 Gen9/ProLiant XL420 Gen9, BIOS U19 12/27/2015
Call Trace:
dump_stack+0x62/0x9a
register_lock_class+0x95a/0x960
? __platform_driver_probe+0xcd/0x230
? __platform_create_bundle+0xc0/0xe0
? i8042_init+0x4ec/0x578
? do_one_initcall+0xfe/0x45a
? kernel_init_freeable+0x614/0x6a7
? kernel_init+0x11/0x138
? ret_from_fork+0x35/0x40
? is_dynamic_key+0xf0/0xf0
? rwlock_bug.part.0+0x60/0x60
? __debug_check_no_obj_freed+0x8e/0x250
__lock_acquire.isra.13+0x5f/0x830
? __debug_check_no_obj_freed+0x152/0x250
lock_acquire+0x107/0x220
? __pm_relax.part.2+0x21/0xa0
_raw_spin_lock_irqsave+0x35/0x50
? __pm_relax.part.2+0x21/0xa0
__pm_relax.part.2+0x21/0xa0
wakeup_source_destroy.part.3+0x18/0x190
wakeup_source_register+0x43/0x50
Fixes: c8377adfa7 ("PM / wakeup: Show wakeup sources stats in sysfs")
Reported-by: Qian Cai <cai@lca.pw>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add an ID and a device pointer to 'struct wakeup_source'. Use them to to
expose wakeup sources statistics in sysfs under
/sys/class/wakeup/wakeup<ID>/*.
Co-developed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Co-developed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Tri Vo <trong@android.com>
Tested-by: Kalesh Singh <kaleshsingh@google.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
wakeup_source_init() has no users. Remove it.
As a result, wakeup_source_prepare() is only called from
wakeup_source_create(). Merge wakeup_source_prepare() into
wakeup_source_create() and remove it.
Change wakeup_source_create() behavior so that assigning NULL to wakeup
source's name throws an error.
Signed-off-by: Tri Vo <trong@android.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This commit applies the consolidated hlist_for_each_entry_rcu() support
for lockdep conditions.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.ibm.com>
If device_link_add() is called for a consumer/supplier pair with an
existing device link between them and the existing link's type is
not in agreement with the flags passed to that function by its
caller, NULL will be returned. That is seriously inconvenient,
because it forces the callers of device_link_add() to worry about
what others may or may not do even if that is not relevant to them
for any other reasons.
It turns out, however, that this limitation can be made go away
relatively easily.
The underlying observation is that if DL_FLAG_STATELESS has been
passed to device_link_add() in flags for the given consumer/supplier
pair at least once, calling either device_link_del() or
device_link_remove() to release the link returned by it should work,
but there are no other requirements associated with that flag. In
turn, if at least one of the callers of device_link_add() for the
given consumer/supplier pair has not passed DL_FLAG_STATELESS to it
in flags, the driver core should track the status of the link and act
on it as appropriate (ie. the link should be treated as "managed").
This means that DL_FLAG_STATELESS needs to be set for managed device
links and it should be valid to call device_link_del() or
device_link_remove() to drop references to them in certain
sutiations.
To allow that to happen, introduce a new (internal) device link flag
called DL_FLAG_MANAGED and make device_link_add() set it automatically
whenever DL_FLAG_STATELESS is not passed to it. Also make it take
additional references to existing device links that were previously
stateless (that is, with DL_FLAG_STATELESS set and DL_FLAG_MANAGED
unset) and will need to be managed going forward and initialize
their status (which has been DL_STATE_NONE so far).
Accordingly, when a managed device link is dropped automatically
by the driver core, make it clear DL_FLAG_MANAGED, reset the link's
status back to DL_STATE_NONE and drop the reference to it associated
with DL_FLAG_MANAGED instead of just deleting it right away (to
allow it to stay around in case it still needs to be released
explicitly by someone).
With that, since setting DL_FLAG_STATELESS doesn't mean that the
device link in question is not managed any more, replace all of the
status-tracking checks against DL_FLAG_STATELESS with analogous
checks against DL_FLAG_MANAGED and update the documentation to
reflect these changes.
While at it, make device_link_add() reject flags that it does not
recognize, including DL_FLAG_MANAGED.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Saravana Kannan <saravanak@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Review-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/2305283.AStDPdUUnE@kreacher
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note that after previous changes dpm_noirq_begin() and
dpm_noirq_end() each have only one caller, so move the code from
them to their respective callers and drop them.
Also note that dpm_noirq_resume_devices() and
dpm_noirq_suspend_devices() need not be exported any more, so make
them both static.
This change is not expected to alter functionality.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
After commit 33e4f80ee6 ("ACPI / PM: Ignore spurious SCI wakeups
from suspend-to-idle") the "noirq" phases of device suspend and
resume may run for multiple times during suspend-to-idle, if there
are spurious system wakeup events while suspended. However, this
is complicated and fragile and actually unnecessary.
The main reason for doing this is that on some systems the EC may
signal system wakeup events (power button events, for example) as
well as events that should not cause the system to resume (spurious
system wakeup events). Thus, in order to determine whether or not
a given event signaled by the EC while suspended is a proper system
wakeup one, the EC GPE needs to be dispatched and to start with that
was achieved by allowing the ACPI SCI action handler to run, which
was only possible after calling resume_device_irqs().
However, dispatching the EC GPE this way turned out to take too much
time in some cases and some EC events might be missed due to that, so
commit 68e2201185 ("ACPI: EC: Dispatch the EC GPE directly on
s2idle wake") started to dispatch the EC GPE right after a wakeup
event has been detected, so in fact the full ACPI SCI action handler
doesn't need to run any more to deal with the wakeups coming from the
EC.
Use this observation to simplify the suspend-to-idle control flow
so that the "noirq" phases of device suspend and resume are each
run only once in every suspend-to-idle cycle, which is reported to
significantly reduce power drawn by some systems when suspended to
idle (by allowing them to reach a deep platform-wide low-power state
through the suspend-to-idle flow). [What appears to happen is that
the "noirq" resume of devices after a spurious EC wakeup brings some
devices into a state in which they prevent the platform from reaching
the deep low-power state going forward, even after a subsequent
"noirq" suspend phase, and on some systems the EC triggers such
wakeups already when the "noirq" suspend of devices is running for
the first time in the given suspend/resume cycle, so the platform
cannot reach the deep low-power state at all.]
First, make acpi_s2idle_wake() use the acpi_ec_dispatch_gpe() return
value to determine whether or not the wakeup may have been triggered
by the EC (in which case the system wakeup is canceled and ACPI
events are processed in order to determine whether or not the event
is a proper system wakeup one) and use rearm_wake_irq() (introduced
by a previous change) in it to rearm the ACPI SCI for system wakeup
detection in case the system will remain suspended.
Second, drop acpi_s2idle_sync(), which is not needed any more, and
the corresponding global platform suspend-to-idle callback.
Next, drop the pm_wakeup_pending() check (which is an optimization
only) from __device_suspend_noirq() to prevent it from returning
errors on system wakeups occurring before the "noirq" phase of
device suspend is complete (as in the case of suspend-to-idle it is
not known whether or not these wakeups are suprious at that point),
in order to avoid having to carry out a "noirq" resume of devices
on a spurious system wakeup.
Finally, change the code flow in s2idle_loop() to (1) run the
"noirq" suspend of devices once before starting the loop, (2) check
for spurious EC wakeups (via the platform ->wake callback) for the
first time before calling s2idle_enter(), and (3) run the "noirq"
resume of devices once after leaving the loop.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
It is not actually guaranteed that pm_abort_suspend will be
nonzero when pm_system_cancel_wakeup() is called which may lead to
subtle issues, so make it use atomic_dec_if_positive() instead of
atomic_dec() for the safety sake.
Fixes: 33e4f80ee6 ("ACPI / PM: Ignore spurious SCI wakeups from suspend-to-idle")
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
* pm-cpufreq:
cpufreq: Make cpufreq_generic_init() return void
cpufreq: imx-cpufreq-dt: Add i.MX8MN support
cpufreq: Add QoS requests for userspace constraints
cpufreq: intel_pstate: Reuse refresh_frequency_limits()
cpufreq: Register notifiers with the PM QoS framework
PM / QoS: Add support for MIN/MAX frequency constraints
PM / QOS: Pass request type to dev_pm_qos_read_value()
PM / QOS: Rename __dev_pm_qos_read_value() and dev_pm_qos_raw_read_value()
PM / QOS: Pass request type to dev_pm_qos_{add|remove}_notifier()
* pm-opp:
opp: Don't use IS_ERR on invalid supplies
opp: Make dev_pm_opp_set_rate() handle freq = 0 to drop performance votes
opp: Don't overwrite rounded clk rate
opp: Allocate genpd_virt_devs from dev_pm_opp_attach_genpd()
opp: Attach genpds to devices from within OPP core
* pm-misc:
PM / clk: Remove error message on out-of-memory condition
drivers: base: power: clock_ops: Use of_clk_get_parent_count()
* pm-avs:
power: avs: smartreflex: no need to check return value of debugfs_create functions
* pm-tools:
cpupower : frequency-set -r option misses the last cpu in related cpu list
cpupower: correct spelling of interval
Add README and update pm-graph and sleepgraph docs
Update to pm-graph 5.4
Update to pm-graph 5.3
After recent hibernation-related changes, there are no more callers
of dev_pm_skip_next_resume_phases() except for the PM core itself
in which it is more straightforward to run the statements from
that function directly, so do that and drop it.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
