The firmware does not respond ARP request and causes ping failure with
following steps:
1. Bring up interface
ifconfig wlan0 up or start wpa_supplicant
2. Set the IP address
ifconfig wlan0 192.168.100.10
3. Bring down interface or
ifconfig wlan0 down or kill wpa_supplicant
4. Bring up interface again and set the same IP address
5. Connect to AP(192.168.100.1) and ping to AP will be failed.
FMAC clears arp_hostip when bringing down the interface, but not set it
back if setting the same IP address. We are able to see the IP address
in interface info(inconfig wlan0) but the ping still cannot work because
the firmware ARP offload does not respond the ARP request.
Because of that, we remove "arp_hostip_clear" from function
"brcmf_netdev_stop"
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-3-git-send-email-chi-hsien.lin@cypress.com
When starting station mode on wlan0 and AP mode on wlan1, the apsta will
be disabled and cause data stall on wlan0(station). The apsta feature
with MCHAN(Multi-Channel Concurrent) or RSDB(Real Simultaneous
Dual-Band) can make STA+AP work on two bands concurrently.
Because of that, we keep apsta enabled if firmware supports MCHAN or
RSDB features
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1587970803-77700-2-git-send-email-chi-hsien.lin@cypress.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/stf.c:309:5-13:
Unneeded variable: "ret_code". Return "0" on line 328
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200413082126.22572-1-yanaijie@huawei.com
Sparse reports a warning at brcms_down()
warning: context imbalance in brcms_down()
- unexpected unlock
The root cause is the missing annotation at brcms_down()
Add the missing __must_hold(&wl->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200411001933.10072-6-jbi.octave@gmail.com
Sparse reports a warning at brcms_rfkill_set_hw_state()
warning: context imbalance in brcms_rfkill_set_hw_state()
- unexpected unlock
The root cause is the missing annotation at brcms_rfkill_set_hw_state()
Add the missing __must_hold(&wl->lock) annotation
Signed-off-by: Jules Irenge <jbi.octave@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200411001933.10072-5-jbi.octave@gmail.com
Fix the following coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3773:5-8:
Unneeded variable: "err". Return "0" on line 3781
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200410090817.26883-1-yanaijie@huawei.com
This patch fixes commit 75388acd0c ("add mac80211-based driver for
legacy BCM43xx devices")
In https://bugzilla.kernel.org/show_bug.cgi?id=207093, a defect in
b43legacy is reported. Upon testing, thus problem exists on PPC and
X86 platforms, is present in the oldest kernel tested (3.2), and
has been present in the driver since it was first added to the kernel.
The problem is a corrupted channel status received from the device.
Both the internal card in a PowerBook G4 and the PCMCIA version
(Broadcom BCM4306 with PCI ID 14e4:4320) have the problem. Only Rev, 2
(revision 4 of the 802.11 core) of the chip has been tested. No other
devices using b43legacy are available for testing.
Various sources of the problem were considered. Buffer overrun and
other sources of corruption within the driver were rejected because
the faulty channel status is always the same, not a random value.
It was concluded that the faulty data is coming from the device, probably
due to a firmware bug. As that source is not available, the driver
must take appropriate action to recover.
At present, the driver reports the error, and them continues to process
the bad packet. This is believed that to be a mistake, and the correct
action is to drop the correpted packet.
Fixes: 75388acd0c ("add mac80211-based driver for legacy BCM43xx devices")
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-and-tested by: F. Erhard <erhard_f@mailbox.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200407190043.1686-1-Larry.Finger@lwfinger.net
Pointer 'address' is being assigned and updated in a few places
by it is never read. Hence the assignments are redundant and can
be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200405133906.381358-1-colin.king@canonical.com
sup_wpa feature is getting after setting feature_disable flag.
If firmware is supported sup_wpa feature, it's always enabled
regardless of feature_disable flag.
Fixes: b8a64f0e96 ("brcmfmac: support 4-way handshake offloading for WPA/WPA2-PSK")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200330052528.10503-1-jh80.chung@samsung.com
We add enable dynamic suspend (autosuspend) support in host driver, and
it can let platform cut down idle power consumption.
To support autosuspend feature in host driver, kernel need to be built
with CONFIG_USB_SUSPEND and autosuspend need to be turn on.
And we also replace wowl feature with adding "needs_remote_wakeup", so
that host still can be waken by wireless device.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-6-git-send-email-chi-hsien.lin@cypress.com
Will enable FMAC to push more packets to bus tx queue and help
improve throughput when fws queuing is enabled. This change is
required to tune the throughput for passing WMM CERT tests.
Signed-off-by: Madhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-5-git-send-email-chi-hsien.lin@cypress.com
The function brcmf_inform_single_bss returns the value as success,
even when the length exceeds the maximum value.
The fix is to send appropriate code on this error.
This issue is observed when Cypress test group reported random fmac
crashes when running their tests and the path was identified from the
crash logs. With this fix the random failure issue in Cypress test group
was resolved.
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-4-git-send-email-chi-hsien.lin@cypress.com
When the brcmf_fws_process_skb() fails to get hanger slot for
queuing the skb, it tries to free the skb.
But the caller brcmf_netdev_start_xmit() of that funciton frees
the packet on error return value.
This causes the double freeing and which caused the kernel crash.
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-3-git-send-email-chi-hsien.lin@cypress.com
When the control transfer gets timed out, the error status
was returned without killing that urb, this leads to using
the same urb. This issue causes the kernel crash as the same
urb is sumbitted multiple times. The fix is to kill the
urb for timeout transfer before returning error
Signed-off-by: Raveendran Somu <raveendran.somu@cypress.com>
Signed-off-by: Chi-hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585124429-97371-2-git-send-email-chi-hsien.lin@cypress.com
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200225020804.GA9428@embeddedor
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: b43-dev@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Cc: b43-dev@lists.infradead.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The simple_strtol() function is deprecated since it does not
check for the range overflow. Use kstrtoint() instead.
Signed-off-by: chenqiwu <chenqiwu@xiaomi.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With commit 216b44000a ("brcmfmac: Fix use after free in
brcmf_sdio_readframes()") applied, we see locking timeouts in
brcmf_sdio_watchdog_thread().
brcmfmac: brcmf_escan_timeout: timer expired
INFO: task brcmf_wdog/mmc1:621 blocked for more than 120 seconds.
Not tainted 4.19.94-07984-g24ff99a0f713 #1
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
brcmf_wdog/mmc1 D 0 621 2 0x00000000 last_sleep: 2440793077. last_runnable: 2440766827
[<c0aa1e60>] (__schedule) from [<c0aa2100>] (schedule+0x98/0xc4)
[<c0aa2100>] (schedule) from [<c0853830>] (__mmc_claim_host+0x154/0x274)
[<c0853830>] (__mmc_claim_host) from [<bf10c5b8>] (brcmf_sdio_watchdog_thread+0x1b0/0x1f8 [brcmfmac])
[<bf10c5b8>] (brcmf_sdio_watchdog_thread [brcmfmac]) from [<c02570b8>] (kthread+0x178/0x180)
In addition to restarting or exiting the loop, it is also necessary to
abort the command and to release the host.
Fixes: 216b44000a ("brcmfmac: Fix use after free in brcmf_sdio_readframes()")
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Brian Norris <briannorris@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: franky.lin@broadcom.com
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The 2018 13" MacBook Pro (MacBookPro15,2) has a Broadcom chip, the 4364.
This chip appears to be specific to Apple and is not found in other
hardware.
Add this chip to the brcmfmac driver so that it can be recognized
automatically. Note that the PCI device id is 4464 even though the chip
is referred to as the 4364.
Signed-off-by: brian m. carlson <sandals@crustytoothpaste.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
Report monitor interface availability using cfg80211 and support it in
the add_virtual_intf() and del_virtual_intf() callbacks. This new
feature is conditional and depends on firmware flagging monitor packets.
Receiving monitor frames is already handled by the brcmf_netif_mon_rx().
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Move similar/duplicated code out of combination specific code blocks.
This simplifies code a bit and allows adding more combinations later.
A list of combinations remains unchanged.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling
brcmf_bus_started()") changed the initialization order of the brcmfmac
SDIO driver. Unfortunately since brcmf_sdiod_intr_register() is now
called before the sdiodev->bus_if initialization, it reads the wrong
chip ID and fails to initialize the GPIO on brcm43362. Thus the chip
cannot send interrupts and fails to probe:
[ 12.517023] brcmfmac: brcmf_sdio_bus_rxctl: resumed on timeout
[ 12.531214] ieee80211 phy0: brcmf_bus_started: failed: -110
[ 12.536976] ieee80211 phy0: brcmf_attach: dongle is not responding: err=-110
[ 12.566467] brcmfmac: brcmf_sdio_firmware_callback: brcmf_attach failed
Initialize the bus interface earlier to ensure that
brcmf_sdiod_intr_register() properly sets up the OOB interrupt.
BugLink: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=908438
Fixes: 262f2b53f6 ("brcmfmac: call brcmf_attach() just before calling brcmf_bus_started()")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwsignal.c:911:2-24: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
NVIDIA Tegra SoCs do not like when OOB wake is enabled and WiFi interface
is in DOWN state during suspend. This results in a CPU hang on programming
OOB wake-up state of the GPIO controller during of system's suspend.
The solution is trivial: don't enable wake for the OOB interrupt when it
should be disabled.
This fixes hang on Tegra20 (Acer A500) and Tegra30 (Nexus 7) devices which
are using BCM4329 and BCM4330 WiFi chips respectively.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the implementation of brcmf_usbdev_qinit() the allocated memory for
reqs is leaking if usb_alloc_urb() fails. Release reqs in the error
handling path.
Fixes: 71bb244ba2 ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With RSDB mode, FMAC and firmware are able to create 2 or more AP,
so we should not set mbss in vif structure if firmware does not
support MBSS feature.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With firmware RSDB feature
1. The maximum support interface is four.
2. The maximum difference channel is two.
3. The maximum interfaces of {station/p2p client/AP} are two.
4. The maximum interface of p2p device is one.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BCM4359 is a 2x2 802.11 abgn+ac Dual-Band HT80 combo chip and it
supports Real Simultaneous Dual Band feature.
Based on a similar patch by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
4359 dongles do not support setting roaming parameters (error -52).
Do not fail the 80211 configuration in this case.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer 4359 chip revisions need a different rambase address.
This fixes firmware download on such devices which fails otherwise.
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Set F2 blocksize to 256 bytes and watermark to 0x40 for 4359. Also
enable and configure F1 MesBusyCtrl. It fixes DMA error while having
UDP bi-directional traffic.
Signed-off-by: Chung-Hsien Hsu <stanley.hsu@cypress.com>
[slightly adapted for rebase on mainline linux]
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two D11 cores in RSDB chips like 4359. We have to reset two
D11 cores simutaneously before firmware download, or the firmware may
not be initialized correctly and cause "fw initialized failed" error.
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Chi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: 71bb244ba2 ("brcm80211: fmac: add USB support for bcm43235/6/8 chipsets")
Cc: stable <stable@vger.kernel.org> # 3.4
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's important as brcmfmac creates one main interface for each PHY and
doesn't allow deleting it. Not setting carrier could result in other
subsystems misbehaving (e.g. LEDs "netdev" trigger turning LED on).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The brcmu_pkt_buf_free_skb() function frees "pkt" so it leads to a
static checker warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1974 brcmf_sdio_readframes()
error: dereferencing freed memory 'pkt'
It looks like there was supposed to be a continue after we free "pkt".
Fixes: 4754fceeb9 ("brcmfmac: streamline SDIO read frame routine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As 'channel' is declared as u16, the following expression is always false.
channel < 0
So we can remove unnecessary 'always false' statement.
Signed-off-by: Austin Kim <austindh.kim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the implementation of brcmf_p2p_create_p2pdev() the allocated memory
for p2p_vif is leaked when the mac address is the same as primary
interface. To fix this, go to error path to release p2p_vif via
brcmf_free_vif().
Fixes: cb746e4783 ("brcmfmac: check p2pdev mac address uniqueness")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This fixes a minor WARNING in the cfg80211:
[ 130.658034] ------------[ cut here ]------------
[ 130.662805] WARNING: CPU: 1 PID: 610 at net/wireless/core.c:954 wiphy_unregister+0xb4/0x198 [cfg80211]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_get_regaddr:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:790:5: warning: variable mpnum set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_erom_scan:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:866:10: warning: variable nsp set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c: In function brcmf_chip_dmp_erom_scan:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/chip.c:866:5: warning: variable nmp set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:841:7: warning: variable free_pdu set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:30: warning: variable tx_rts_count set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:6: warning: variable tx_rts set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:843:7: warning: variable totlen set but not used [-Wunused-but-set-variable]
They are never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdwYyqAAoJEG4XJFUm622b/jMH/0KUcGz8y4gkk2B2lMRyUOTu
t84LiSHxcsq6letlr/vak4S6NrxMLP8Z/ByyoKC8o3yeVsdyMNMSLZAztFFhxdXr
Haky2SM10q6vnn9s1skXS/qkHSd2WdUFT2DgYxyOPCtJUazVKjcboJ4YX/TUg99a
5eqPpZ4RXtW6uOmWHS7JXtLcCFPywKPBtMAjLEDMYOUSSBWExBNyNZNhznSS3ywY
4VKvc675gXE+WD3qXRhL8EJjyed94yuS3wYbKWp8iTaIRyluDmc5lVhjWH1A0HLE
Qb62QL8XLtbX5fcTnaupdAIXwxeIBylOBe8QtW7QUbAnGFf8bexLxfnQM+To4wI=
=24zD
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
use true/false for bool type variables assignment.
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
