In commit 629c9a8fd0 (drivers: net: cpsw: Add
default vlan for dual emac case also), api cpsw_add_default_vlan() also
changes the port vlan which is required to seperate the ports which results
in the following behavior
In Dual EMAC mode, when both the Etnernet connected is connected to same
switch, it creates a loop in the switch and when a broadcast packet is
received it is forwarded to the other port which stalls the whole switch
and needs a reset/power cycle to the switch to recover. So intead of using
the api, add only the default VLAN entry in dual EMAC case.
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David Vrabel says:
====================
xen-netfront: fix resume regressions in 3.16-rc1
The introduction of multi-queue support to xen-netfront in 3.16-rc1,
broke resume/migration.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When reconnecting to the backend (after a resume/migration, for example),
a different number of queues may be required (since the guest may have
moved to a different host with different capabilities). During the
reconnection the old queues are torn down and new ones created.
Introduce xennet_create_queues() and xennet_destroy_queues() that fixes
three bugs during the reconnection.
- The old info->queues was leaked.
- The old queue's napi instances were not deleted.
- The new queue's napi instances were left disabled (which meant no
packets could be received).
The xennet_destroy_queues() calls is deferred until the reconnection
instead of the disconnection (in xennet_disconnect_backend()) because
napi_disable() might sleep.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xennet_disconnect_backend() was not correctly iterating over all the
queues.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reviewed-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Mack says:
====================
Handle stuck TX queue bug in AT8030 PHY
These three small patches circument a hardware bug in AT8030 PHYs that
leads to stuck TX FIFO queues when the link goes away while there are
pending patches in der outbound queue. This bug has been confirmed by
the vendor, and their only proposed fix is to apply a hardware reset
every time the link goes down.
v1 -> v2:
* Rename phy device callback from adjust_state to link_change_notify
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT8030 will enter a FIFO error mode if a packet is transmitted while
the cable is unplugged. This hardware issue is acknowledged by the
vendor, and the only proposed solution is to conduct a hardware reset
via the external pin each time the link goes down. There is apparantly
no way to fix up the state via the register set.
This patch adds support for reading a 'reset-gpios' property from the DT
node of the PHY. If present, this gpio is used to apply a hardware reset
each time a 'link down' condition is detected. All relevant registers
are read out before, and written back after the reset cycle.
Doing this every time the link goes down might seem like overkill, but
there is unfortunately no way of figuring out whether the PHY is in
such a lock-up state. Hence, this is the only way of reliably fixing up
things.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes magic values from two tables and also allows us to match
against specific PHY models at runtime.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a notify callback to inform phy drivers when the core is about to
do its link adjustment. No change for drivers that do not implement
this callback.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_cow called in vlan_reorder_header does not free the skb when it failed,
and vlan_reorder_header returns NULL to reset original skb when it is called
in vlan_untag, lead to a memory leak.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull perf fixes from Ingo Molnar:
"This is larger than usual: the main reason are the ARM symbol lookup
speedups that came in late and were hard to resist.
There's also a kprobes fix and various tooling fixes, plus the minimal
re-enablement of the mmap2 support interface"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/kprobes: Fix build errors and blacklist context_track_user
perf tests: Add test for closing dso objects on EMFILE error
perf tests: Add test for caching dso file descriptors
perf tests: Allow reuse of test_file function
perf tests: Spawn child for each test
perf tools: Add dso__data_* interface descriptons
perf tools: Allow to close dso fd in case of open failure
perf tools: Add file size check and factor dso__data_read_offset
perf tools: Cache dso data file descriptor
perf tools: Add global count of opened dso objects
perf tools: Add global list of opened dso objects
perf tools: Add data_fd into dso object
perf tools: Separate dso data related variables
perf tools: Cache register accesses for unwind processing
perf record: Fix to honor user freq/interval properly
perf timechart: Reflow documentation
perf probe: Improve error messages in --line option
perf probe: Improve an error message of perf probe --vars mode
perf probe: Show error code and description in verbose mode
perf probe: Improve error message for unknown member of data structure
...
Pull rtmutex fixes from Thomas Gleixner:
"Another three patches to make the rtmutex code more robust. That's
the last urgent fallout from the big futex/rtmutex investigation"
* 'locking-urgent-for-linus.patch' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rtmutex: Plug slow unlock race
rtmutex: Detect changes in the pi lock chain
rtmutex: Handle deadlock detection smarter
Pull s390 patches from Martin Schwidefsky:
"A couple of bug fixes, a debug change for qdio, an update for the
default config, and one small extension.
The watchdog module based on diagnose 0x288 is converted to the
watchdog API and it now works under LPAR as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/ccwgroup: use ccwgroup_ungroup wrapper
s390/ccwgroup: fix an uninitialized return code
s390/ccwgroup: obtain extra reference for asynchronous processing
qdio: Keep device-specific dbf entries
s390/compat: correct ucontext layout for high gprs
s390/cio: set device name as early as possible
s390: update default configuration
s390: avoid format strings leaking into names
s390/airq: silence lockdep warning
s390/watchdog: add support for LPAR operation (diag288)
s390/watchdog: use watchdog API
s390/sclp_vt220: Enable ASCII console per default
s390/qdio: replace shift loop by ilog2
s390/cio: silence lockdep warning
s390/uaccess: always load the kernel ASCE after task switch
s390/ap_bus: Make modules parameters visible in sysfs
Here are 3 patches, one a revert of the UIO patch you objected to in
3.16-rc1 and that no one wanted to defend, a w1 driver bugfix, and a
MAINTAINERS update for the vmware balloon driver. All of these, except
for the MAINTAINERS update which just got added, have been in linux-next just
fine.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlOkkTEACgkQMUfUDdst+ynIKACgxyvwXygqwiKaNutDvwrP9l+e
3joAn0gW1wVUq+7r/msb7sWosuNF9S2F
=kc9k
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver fixes from Greg KH:
"Here are 3 patches, one a revert of the UIO patch you objected to in
3.16-rc1 and that no one wanted to defend, a w1 driver bugfix, and a
MAINTAINERS update for the vmware balloon driver.
All of these, except for the MAINTAINERS update which just got added,
have been in linux-next just fine"
* tag 'char-misc-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: add entry for VMware Balloon driver
w1: mxc_w1: Fix incorrect "presence" status
Revert "uio: fix vma io range check in mmap"
Here are a few fixes for staging and iio drivers that resolve issues
reported in 3.16-rc1.
All have been in linux-next just fine.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlOkj58ACgkQMUfUDdst+ykg8QCfdKDeHmeZI2TEUadR460FJy4c
B5IAnAsLSIL/KPhLGjC5f1Ored6ESXal
=Ml7O
-----END PGP SIGNATURE-----
Merge tag 'staging-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg KH:
"Here are a few fixes for staging and iio drivers that resolve issues
reported in 3.16-rc1.
All have been in linux-next just fine"
* tag 'staging-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
imx-drm: parallel-display: Fix DPMS default state.
staging: android: timed_output: fix use after free of dev
staging: comedi: addi_apci_1564: add addi_watchdog dependency
staging: rtl8723au: Reference correct firmwarefiles with MODULE_FIRMWARE()
staging: rtl8723au: Request correct firmware file for A-cut parts
iio: adc: checking for NULL instead of IS_ERR() in probe
iio: adc: at91: signedness bug in at91_adc_get_trigger_value_by_name()
iio: mxs-lradc: fix divider
iio: Fix endianness issue in ak8975_read_axis()
staging/iio: IIO_SIMPLE_DUMMY_BUFFER neds IIO_BUFFER
twl4030-madc: Request processed values in twl4030_get_madc_conversion
staging: iio: tsl2x7x_core: fix proximity treshold
iio: Fix two mpl3115 issues in measurement conversion
iio: hid-sensors: Get feature report from sensor hub after changing power state
Here are some tty / serial driver bugfixes for 3.16-rc2 that resolve
some reported issues. The samsung driver build error itself has been
reported by a bunch of people, sorry about that one. The others are all
tiny and everyone seems to like them in linux-next so far.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlOkkKQACgkQMUfUDdst+ymZbwCgt1mJsOte0uOmb/bzDkJiM4mX
JuYAn3BF53FY50Y/bY1cVpcSDCbwFPdp
=gugC
-----END PGP SIGNATURE-----
Merge tag 'tty-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial bugfixes from Greg KH:
"Here are some tty / serial driver bugfixes for 3.16-rc2 that resolve
some reported issues. The samsung driver build error itself has been
reported by a bunch of people, sorry about that one. The others are
all tiny and everyone seems to like them in linux-next so far"
* tag 'tty-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty/serial: fix 8250 early console option passing to regular console
tty: Correct INPCK handling
serial: Fix IGNBRK handling
serial: samsung: Fix build error
Here are some USB fixes for 3.16-rc2 that resolve some reported issues.
All of these have been in linux-next for a while with no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlOkkZcACgkQMUfUDdst+ykfMQCfS3ANqdOu7FFfdnnzYLbQRiFP
RGUAn0/x1x6CGD5HKHWRE9NnmpZImGgU
=+3+c
-----END PGP SIGNATURE-----
Merge tag 'usb-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB fixes for 3.16-rc2 that resolve some reported
issues. All of these have been in linux-next for a while with no
problems"
* tag 'usb-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: usbtest: add a timeout for scatter-gather tests
USB: EHCI: avoid BIOS handover on the HASEE E200
usb: fix hub-port pm_runtime_enable() vs runtime pm transitions
usb: quiet peer failure warning, disable poweroff
usb: improve "not suspended yet" message in hub_suspend()
xhci: Fix sleeping with IRQs disabled in xhci_stop_device()
usb: fix ->update_hub_device() vs hdev->maxchild
On exynos mcpm systems the firmware is hardcoded to jump to an address
in SRAM (0x02073000) when secondary CPUs come up. By default the
firmware puts a bunch of code at that location. That code expects the
kernel to fill in a few slots with addresses that it uses to jump back
to the kernel's entry point for secondary CPUs.
Originally (on prerelease hardware) this firmware code contained a
bunch of workarounds to deal with boot ROM bugs. However on all
shipped hardware we simply use this code to redirect to a kernel
function for bringing up the CPUs.
Let's stop relying on the code provided by the bootloader and just
plumb in our own (simple) code jump to the kernel. This has the nice
benefit of fixing problems due to the fact that older bootloaders
(like the one shipped on the Samsung Chromebook 2) might have put
slightly different code into this location.
Once suspend/resume is implemented for systems using exynos-mcpm we'll
need to make sure we reinstall our fixed up code after resume. ...but
that's not anything new since IRAM (and thus the address of the
mcpm_entry_point) is lost across suspend/resume anyway.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The following commit:
89d7e5c mmc: sdhci-esdhc-imx: add runtime pm support
has the effect of also disabling the hardware card detect
in runtime pm.
We switch to GPIO based detection to avoid this issue.
This patch is based on:
ARM: dts: imx51-babbage: Fix esdhc setup
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since commit 89d7e5c131 (mmc: sdhci-esdhc-imx: add runtime pm
support), controller based card detection / write protection is not
supported anymore by esdhc driver. Let's use GPIO for CD/WP on esdhc1
instead.
While at it, fix cd gpio polarity for esdhc2. This is wrong and
currently only works because the imx esdhc driver ignores the polarity.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Move the display {} node out of the soc {} node . This just aligns
the DT with other boards, there is no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Currently the __field() macro in TRACE_EVENT is only good for primitive
values, such as integers and pointers, but it fails on complex data types
such as structures or unions. This is because the __field() macro
determines if the variable is signed or not with the test of:
(((type)(-1)) < (type)1)
Unfortunately, that fails when type is a structure.
Since trace events should support structures as fields a new macro
is created for such a case called __field_struct() which acts exactly
the same as __field() does but it does not do the signed type check
and just uses a constant false for that answer.
Cc: Tony Luck <tony.luck@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
syscall_regfunc() ignores the kernel threads because "it has no effect",
see cc3b13c1 "Don't trace kernel thread syscalls" which added this check.
However, this means that a user-space task spawned by call_usermodehelper()
will run without TIF_SYSCALL_TRACEPOINT if sys_tracepoint_refcount != 0.
Remove this check. The unnecessary report from ret_from_fork path mentioned
by cc3b13c1 is no longer possible, see See commit fb45550d76 "make sure
that kernel_thread() callbacks call do_exit() themselves".
A kernel_thread() callback can only return and take the int_ret_from_sys_call
path after do_execve() succeeds, otherwise the kernel will crash. But in this
case it is no longer a kernel thread and thus is needs TIF_SYSCALL_TRACEPOINT.
Link: http://lkml.kernel.org/p/20140413185938.GD20668@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
1. Remove _irqsafe from syscall_regfunc/syscall_unregfunc,
read_lock(tasklist) doesn't need to disable irqs.
2. Change this code to avoid the deprecated do_each_thread()
and use for_each_process_thread() (stolen from the patch
from Frederic).
3. Change syscall_regfunc() to check PF_KTHREAD to skip
the kernel threads, ->mm != NULL is the common mistake.
Note: probably this check should be simply removed, needs
another patch.
[fweisbec@gmail.com: s/do_each_thread/for_each_process_thread/]
Link: http://lkml.kernel.org/p/20140413185918.GC20668@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
syscall_regfunc() and syscall_unregfunc() should set/clear
TIF_SYSCALL_TRACEPOINT system-wide, but do_each_thread() can race
with copy_process() and miss the new child which was not added to
the process/thread lists yet.
Change copy_process() to update the child's TIF_SYSCALL_TRACEPOINT
under tasklist.
Link: http://lkml.kernel.org/p/20140413185854.GB20668@redhat.com
Cc: stable@vger.kernel.org # 2.6.33
Fixes: a871bd33a6 "tracing: Add syscall tracepoints"
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The "port" node was misplaced in the original patch, therefore making
the LCD dysfunctional on this board. Fix this by moving the "port" DT
node into the "display {}" node.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
On Marvell Armada platforms, the PMSU (Power Management Service Unit)
controls a number of power management related activities, needed for
things like suspend/resume, CPU hotplug, cpuidle or even simply SMP.
Since cpuidle support was added for Armada XP, the pmsu.c file in
arch/arm/mach-mvebu/ calls the cpu_suspend() and cpu_resume() ARM
functions, which are only available when
CONFIG_ARM_CPU_SUSPEND=y. Therefore, configurations that have
CONFIG_ARM_CPU_SUSPEND disabled due to PM_SLEEP being disabled no
longer build properly, due to undefined references to cpu_suspend()
and cpu_resume().
To fix this, this patch simply ensures CONFIG_ARM_CPU_SUSPEND is
always enabled for Marvell EBU v7 platforms. Doing things in a more
fine-grained way would require a lot of #ifdef-ery in pmsu.c to
isolate the parts that use cpu_suspend()/cpu_resume(), and those parts
would anyway have been needed as soon as either one of suspend/resume,
CPU hotplug or cpuidle was enabled.
Reported-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Link: https://lkml.kernel.org/r/1402488397-31381-1-git-send-email-thomas.petazzoni@free-electrons.com
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Currently the mvebu boards need to detect the SoC revision in order to apply
some quirks needed to workaround issues found on I2C and thermal controllers
present only in very early SoC.
This detection requires PCI address translation to work, so we need to
explicitly select OF_ADDRESS_PCI.
This can be considered a partial revert of the following commit, that
wrongly removed the option selection:
commit 55400f3a1f
Author: Rob Herring <robh@kernel.org>
Date: Tue Apr 22 14:15:52 2014 -0500
ARM: mvebu: clean-up unneeded kconfig selects
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Link: https://lkml.kernel.org/r/1402347165-19988-1-git-send-email-ezequiel.garcia@free-electrons.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Since commit 39b9004d1f (gpu: ipu-v3: Move i.MX IPUv3 core driver out of
staging) the ipuv3 core driver is no longer built bey default.
Select CONFIG_IMX_IPUV3_CORE so that the core ipuv3 code can be built again.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
If we need an MITM protected connection but the local and remote IO
capabilities cannot provide it we should reject the pairing attempt in
the appropriate way. This patch adds the missing checks for such a
situation to the smp_cmd_pairing_req() and smp_cmd_pairing_rsp()
functions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll need to do authentication method lookups from more than one place,
so refactor the lookup into its own function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we receive a pairing request or an internal request to start
pairing we shouldn't blindly overwrite the existing pending_sec_level
value as that may actually be higher than the new one. This patch fixes
the SMP code to only overwrite the value in case the new one is higher
than the old.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reverts commit ca58e594da.
For some unclear reason this patch tries to add suport for the
product ID 0xe005, but it ends up adding product ID 0x3005 to
all the tables. This is obviously wrong and causing multiple
issues.
The original patch seemed to be fine, but what ended up in 3.15
is not what the patch intended. The commit 0a3658cccd is
already present and adds support for this hardware. This means
only revert of this broken commit is requird.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Reported-by: Alexander Holler <holler@ahsoftware.de>
Cc: stable@vger.kernel.org # 3.15.x
Commit ca8f0b0a54 ("ARM: ensure C page table setup code follows
assembly code") did what it said on the tin, but some of the older
CPU code omitted the default cache policy from their files. This
results in the kernel running with the caches disabled. Fix this
for ARM925.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds QCOM GSBI config option to multi_v7_defconfig. Serial
driver on QCOM APQ8064 depends on GSBI driver, so without this patch
there is no serial console on IF6410 board using multi_v7_defconfig.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The fixes included are:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gew5
-----END PGP SIGNATURE-----
Merge tag 'sti-fixes-for-v3.16-rc1' of git://git.stlinux.com/devel/kernel/linux-sti into fixes
Merge "STi: DT fixes for v3.16" from Maxime Coquelin:
Couple of DT fixes for STi platform issues discovered on V3.16-rc1.
The fixes included are:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase.
* tag 'sti-fixes-for-v3.16-rc1' of git://git.stlinux.com/devel/kernel/linux-sti: (2963 commits)
ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
ARM: STi: DT: Properly define sti-ethclk & stmmaceth for stih415/6
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix for an ia64 regression introduced during the 3.11 cycle by a
commit that modified the hardware initialization ordering and made
device discovery fail on some systems.
- Fix for a build problem on systems where the cpufreq-cpu0 driver
is built-in and the cpu-thermal driver is modular from Arnd Bergmann.
- Fix for a recently introduced computational mistake in the
intel_pstate driver that leads to excessive rounding errors from
Doug Smythies.
- Fix for a failure code path in cpufreq_update_policy() that fails
to unlock the locks acquired previously from Aaron Plattner.
- Fix for the cpuidle mvebu driver to use shorter state names which
will prevent the sysfs interface from returning mangled strings.
From Gregory Clement.
- ACPI LPSS driver fix to make sure that the I2C controllers
included in BayTrail SoCs are not held in the reset state while
they are being probed from Mika Westerberg.
- New kernel command line arguments making it possible to build
kernel images with hibernation and kASLR included at the same
time and to select which of them will be used via the command
line (they are still functionally mutually exclusive, though).
From Kees Cook.
- ACPI battery driver quirk for Acer Aspire V5-573G that fails
to send battery status change notifications timely from
Alexander Mezin.
- Two ACPI core cleanups from Christoph Jaeger and Fabian Frederick.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=TE5Y
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These are fixes mostly (ia64 regression related to the ACPI
enumeration of devices, cpufreq regressions, fix for I2C controllers
included in Intel SoCs, mvebu cpuidle driver fix related to sysfs)
plus additional kernel command line arguments from Kees to make it
possible to build kernel images with hibernation and the kernel
address space randomization included simultaneously, a new ACPI
battery driver quirk for a system with a broken BIOS and a couple of
ACPI core cleanups.
Specifics:
- Fix for an ia64 regression introduced during the 3.11 cycle by a
commit that modified the hardware initialization ordering and made
device discovery fail on some systems.
- Fix for a build problem on systems where the cpufreq-cpu0 driver is
built-in and the cpu-thermal driver is modular from Arnd Bergmann.
- Fix for a recently introduced computational mistake in the
intel_pstate driver that leads to excessive rounding errors from
Doug Smythies.
- Fix for a failure code path in cpufreq_update_policy() that fails
to unlock the locks acquired previously from Aaron Plattner.
- Fix for the cpuidle mvebu driver to use shorter state names which
will prevent the sysfs interface from returning mangled strings.
From Gregory Clement.
- ACPI LPSS driver fix to make sure that the I2C controllers included
in BayTrail SoCs are not held in the reset state while they are
being probed from Mika Westerberg.
- New kernel command line arguments making it possible to build
kernel images with hibernation and kASLR included at the same time
and to select which of them will be used via the command line (they
are still functionally mutually exclusive, though). From Kees
Cook.
- ACPI battery driver quirk for Acer Aspire V5-573G that fails to
send battery status change notifications timely from Alexander
Mezin.
- Two ACPI core cleanups from Christoph Jaeger and Fabian Frederick"
* tag 'pm+acpi-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: mvebu: Fix the name of the states
cpufreq: unlock when failing cpufreq_update_policy()
intel_pstate: Correct rounding in busy calculation
ACPI: use kstrto*() instead of simple_strto*()
ACPI / processor replace __attribute__((packed)) by __packed
ACPI / battery: add quirk for Acer Aspire V5-573G
ACPI / battery: use callback for setting up quirks
ACPI / LPSS: Take I2C host controllers out of reset
x86, kaslr: boot-time selectable with hibernation
PM / hibernate: introduce "nohibernate" boot parameter
cpufreq: cpufreq-cpu0: fix CPU_THERMAL dependency
ACPI / ia64 / sba_iommu: Restore the working initialization ordering
The significant part here is a few security fixes for ALSA core
control API by Lars. Besides that, there are a few fixes for ASoC
sigmadsp (again by Lars) for building properly, and small fixes for
ASoC rsnd, MMP, PXA and FSL, in addition to a fix for bogus WARNING in
i915/HD-audio binding.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dWKL
-----END PGP SIGNATURE-----
Merge tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"The significant part here is a few security fixes for ALSA core
control API by Lars. Besides that, there are a few fixes for ASoC
sigmadsp (again by Lars) for building properly, and small fixes for
ASoC rsnd, MMP, PXA and FSL, in addition to a fix for bogus WARNING in
i915/HD-audio binding"
* tag 'sound-3.16-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: control: Make sure that id->index does not overflow
ALSA: control: Handle numid overflow
ALSA: control: Don't access controls outside of protected regions
ALSA: control: Fix replacing user controls
ALSA: control: Protect user controls against concurrent access
drm/i915, HD-audio: Don't continue probing when nomodeset is given
ASoC: fsl: Fix build problem
ASoC: rsnd: fixup index of src/dst mod when capture
ASoC: fsl_spdif: Fix integer overflow when calculating divisors
ASoC: fsl_spdif: Fix incorrect usage of regmap_read()
ASoC: dapm: Make sure register value is in sync with DAPM kcontrol state
ASoC: sigmadsp: Split regmap and I2C support into separate modules
ASoC: MMP audio needs sram support
ASoC: pxa: add I2C dependencies as needed
Pull drm fixes from Dave Airlie:
"This looks bigger than it is, as one of the nouveau firmware fixes
("drm/gf100-/gr: report class data to host on fwmthd failure")
regenerates a bunch of the firmware files after changing the assembly
by a few lines, without that, its more of a
36 files changed, 370 insertions(+), 129 deletions(-)
It contains some vt.c fixes acked by Greg, for rare hard hangs on i915
loading, that also fixes hangs on reload and spurious register write
errors.
drm core: one fix for uninit memory
nouveau: displayport rework caused a few regressions, Ben has been
fixing them as the appear, along with some other fixes
radeon: pageflipping regression fix, deep color fix, mode validation
fixes
i915: fbc disable, vga console kick off, backlight fix, divide-by-zero
fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
drm: fix uninitialized acquire_ctx fields (v2)
drm/radeon: Fix radeon_irq_kms_pflip_irq_get/put() imbalance
Revert "drm/radeon: remove drm_vblank_get|put from pflip handling"
drm/radeon: improve dvi_mode_valid
drm/radeon: update mode_valid testing for DP
drm/radeon: Use dce5/6 hdmi deep color clock setup also on dce8+
drm/nouveau/disp: fix oops in destructor with headless cards
drm/gf117/i2c: no aux channels on this chipset
drm/nouveau/doc: update the thermal documentation
drm/nouveau/pwr: fix typo in fifo wrap handling
drm/nv50/disp: fix a potential oops in supervisor handling
drm/nouveau/disp/dp: don't touch link config after success
drm/nouveau/kms: reference vblank for crtc during pageflip.
drm/gk104/fb/ram: fixups from an earlier search+replace
drm/nv50/gr: remove an unneeded write while initialising PGRAPH
drm/nv50/gr: fix overlap while zeroing zcull regions
drm/gf100-/gr: report class data to host on fwmthd failure
drm/gk104/ibus: increase various random timeouts
drm/gk104/clk: only touch divider for mode we'll be using
drm/radeon: Bypass hw lut's for > 8 bpc framebuffer scanout.
...
John W. Linville says:
====================
pull request: wireless 2014-06-18
Please pull this batch of fixes intended for the 3.16 stream!
For the Bluetooth bits, Gustavo says:
"This is our first batch of fixes for 3.16. Be aware that two patches here
are not exactly bugfixes:
* 71f28af57066 Bluetooth: Add clarifying comment for conn->auth_type
This commit just add some important security comments to the code, we found
it important enough to include it here for 3.16 since it is security related.
* 9f7ec8871132 Bluetooth: Refactor discovery stopping into its own function
This commit is just a refactor in a preparation for a fix in the next
commit (f8680f128b).
All the other patches are fixes for deadlocks and for the Bluetooth protocols,
most of them related to authentication and encryption."
On top of that...
Chin-Ran Lo fixes a problems with overlapping DMA areas in mwifiex.
Michael Braun corrects a couple of issues in order to enable a new
device in rt2800usb.
Rafał Miłecki reverts a b43 patch that caused a regression, fixes a
Kconfig typo, and corrects a frequency reporting error with the G-PHY.
Stanislaw Grsuzka fixes an rfkill regression for rt2500pci, and avoids
a rt2x00 scheduling while atomic BUG.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When writing to the sysctl field net.sctp.auth_enable, it can well
be that the user buffer we handed over to proc_dointvec() via
proc_sctp_do_auth() handler contains something other than integers.
In that case, we would set an uninitialized 4-byte value from the
stack to net->sctp.auth_enable that can be leaked back when reading
the sysctl variable, and it can unintentionally turn auth_enable
on/off based on the stack content since auth_enable is interpreted
as a boolean.
Fix it up by making sure proc_dointvec() returned sucessfully.
Fixes: b14878ccb7 ("net: sctp: cache auth_enable per endpoint")
Reported-by: Florian Westphal <fwestpha@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block fixes from Jens Axboe:
"A smaller collection of fixes for the block core that would be nice to
have in -rc2. This pull request contains:
- Fixes for races in the wait/wakeup logic used in blk-mq from
Alexander. No issues have been observed, but it is definitely a
bit flakey currently. Alternatively, we may drop the cyclic
wakeups going forward, but that needs more testing.
- Some cleanups from Christoph.
- Fix for an oops in null_blk if queue_mode=1 and softirq completions
are used. From me.
- A fix for a regression caused by the chunk size setting. It
inadvertently used max_hw_sectors instead of max_sectors, which is
incorrect, and causes hangs on btrfs multi-disk setups (where hw
sectors apparently isn't set). From me.
- Removal of WQ_POWER_EFFICIENT in the kblockd creation. This was a
recent addition as well, but it actually breaks blk-mq which relies
on strict scheduling. If the workqueue power_efficient mode is
turned on, this breaks blk-mq. From Matias.
- null_blk module parameter description fix from Mike"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: bitmap tag: fix races in bt_get() function
blk-mq: bitmap tag: fix race on blk_mq_bitmap_tags::wake_cnt
blk-mq: bitmap tag: fix races on shared ::wake_index fields
block: blk_max_size_offset() should check ->max_sectors
null_blk: fix softirq completions for queue_mode == 1
blk-mq: merge blk_mq_drain_queue and __blk_mq_drain_queue
blk-mq: properly drain stopped queues
block: remove WQ_POWER_EFFICIENT from kblockd
null_blk: fix name and description of 'queue_mode' module parameter
block: remove elv_abort_queue and blk_abort_flushes
Commit d3f6f3a1d8 ("tg3: Prevent page
allocation failure during TSO workaround") modified driver logic
to use tg3_tso_bug() for any TSO fragment that hits hardware bug
conditions thus the patch increased the scope of work for tg3_tso_bug()
to cover devices that support NETIF_F_TSO6 as well. Prior to the
patch, tg3_tso_bug() would only be used on devices supporting
NETIF_F_TSO.
A regression was introduced for IPv6 packets requiring the workaround.
To properly perform GSO on SKBs with TCPV6 gso_type, we need to call
skb_gso_segment() with NETIF_F_TSO6 feature flag cleared, or the
function will return NULL and cause a kernel oops as tg3 is not handling
a NULL return value. This patch fixes the problem.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A first set of bug fixes that didn't make it for the merge window, and
two Kconfig cleanups that still make sense at this point. Unfortunately,
one of the two cleanups caused an unintended change in the original
version, so we had to revert one part of it and do some more testing
to ensure the rest is really fine. There was also a last-minute
rebase of the patches to remove another bad commit.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=/Ylr
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A first set of bug fixes that didn't make it for the merge window, and
two Kconfig cleanups that still make sense at this point.
Unfortunately, one of the two cleanups caused an unintended change in
the original version, so we had to revert one part of it and do some
more testing to ensure the rest is really fine. There was also a
last-minute rebase of the patches to remove another bad commit"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: use menuconfig for sub-arch menus
ARM: multi_v7_defconfig: re-enable SDHCI drivers
ARM: EXYNOS: Fix compilation warning
ARM: exynos: move sysram info to exynos.c
ARM: dts: Specify the NAND ECC scheme explicitly on Armada 385 DB board
ARM: dts: Specify the NAND ECC scheme explicitly on Armada 375 DB board
ARM: exynos: cleanup kconfig option display
misc: vexpress: fix error handling vexpress_syscfg_regmap_init()
ARM: Remove ARCH_HAS_CPUFREQ config option
ARM: integrator: fix section mismatch problem
ARM: mvebu: DT: fix OpenBlocks AX3-4 RAM size
ARM: samsung: make SAMSUNG_DMADEV optional
remoteproc: da8xx: don't select CMA on no-MMU
bus/arm-cci: add dependency on OF && CPU_V7
ARM: keystone requires ARM_PATCH_PHYS_VIRT
ARM: omap2: fix am43xx dependency on l2x0 cache
If there is an MSS change (or misbehaving receiver) that causes a SACK
to arrive that covers the end of an skb but is less than one MSS, then
tcp_match_skb_to_sack() was rounding up pkt_len to the full length of
the skb ("Round if necessary..."), then chopping all bytes off the skb
and creating a zero-byte skb in the write queue.
This was visible now because the recently simplified TLP logic in
bef1909ee3 ("tcp: fixing TLP's FIN recovery") could find that 0-byte
skb at the end of the write queue, and now that we do not check that
skb's length we could send it as a TLP probe.
Consider the following example scenario:
mss: 1000
skb: seq: 0 end_seq: 4000 len: 4000
SACK: start_seq: 3999 end_seq: 4000
The tcp_match_skb_to_sack() code will compute:
in_sack = false
pkt_len = start_seq - TCP_SKB_CB(skb)->seq = 3999 - 0 = 3999
new_len = (pkt_len / mss) * mss = (3999/1000)*1000 = 3000
new_len += mss = 4000
Previously we would find the new_len > skb->len check failing, so we
would fall through and set pkt_len = new_len = 4000 and chop off
pkt_len of 4000 from the 4000-byte skb, leaving a 0-byte segment
afterward in the write queue.
With this new commit, we notice that the new new_len >= skb->len check
succeeds, so that we return without trying to fragment.
Fixes: adb92db857 ("tcp: Make SACK code to split only at mss boundaries")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Ilpo Jarvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
W1 reset_bus() should return zero if slave device is present.
This patch fix this issue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If connector->dpms is left untouched, it defaults
to DRM_MODE_DPMS_ON (0).
As a result, drm_helper_connector_dpms will exit when
it will be asked to set the state to DRM_MODE_DPMS_ON,
because it is already set.
That issue prevented displays from turning on at boot.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
