Keeping the irq_chip definition static shares it with multiple instances
of the mcp23s08 gpiochip in the system. This is bad and now we get this
warning from gpiolib core:
"detected irqchip that is shared with multiple gpiochips: please fix the
driver."
Hence, move the irq_chip definition from being driver static into the
struct mcp23s08. So a unique irq_chip is used for each gpiochip
instance.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Armada 3700 PCIe IP relies on the pinctrl IP managed by this
driver. For reasons related to the PCI core's organization when
suspending/resuming, PCI host controller drivers must reconfigure
their register at suspend_noirq()/resume_noirq() which happens after
suspend()/suspend_late() and before resume_early()/resume().
In the current state, after resuming from a suspend to RAM cycle the
PCIe IP is reconfigured before the pinctrl one which produces an
interrupt storm. The solution to support PCIe resume operation is to
change the "priority" of this pinctrl driver PM callbacks to
"_noirq()".
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Gigabit Ethernet requires the Ethernet TXD0..3 and RXD0..3 data lines.
Add the missing eth_rxd2 and eth_rxd3 definitions so we don't have to
rely on the bootloader to set them up correctly.
The vendor u-boot sources for Odroid-C1 use the following Ethernet
pinmux configuration:
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_6, 0x3f4f);
SET_CBUS_REG_MASK(PERIPHS_PIN_MUX_7, 0xf00000);
This translates to the following pin groups in the mainline kernel:
- register 6 bit 0: eth_rxd1 (DIF_0_P)
- register 6 bit 1: eth_rxd0 (DIF_0_N)
- register 6 bit 2: eth_rx_dv (DIF_1_P)
- register 6 bit 3: eth_rx_clk (DIF_1_N)
- register 6 bit 6: eth_tx_en (DIF_3_P)
- register 6 bit 8: eth_ref_clk (DIF_3_N)
- register 6 bit 9: eth_mdc (DIF_4_P)
- register 6 bit 10: eth_mdio_en (DIF_4_N)
- register 6 bit 11: eth_tx_clk (GPIOH_9)
- register 6 bit 12: eth_txd2 (GPIOH_8)
- register 6 bit 13: eth_txd3 (GPIOH_7)
- register 7 bit 20: eth_txd0_0 (GPIOH_6)
- register 7 bit 21: eth_txd1_0 (GPIOH_5)
- register 7 bit 22: eth_rxd3 (DIF_2_P)
- register 7 bit 23: eth_rxd2 (DIF_2_N)
All functions except eth_rxd2 and eth_rxd3 are already supported by the
pinctrl-meson8b driver.
Suggested-by: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Reviewed-by: Emiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Virtual gpio only used inside SOC and not being exported to outside SOC.
Some modules use virtual gpio as eint and doesn't need SMT.
So this patch add EINT support to virtual GPIOs.
Signed-off-by: Chuanjia Liu <Chuanjia.Liu@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a cleanup and fix of the patch by Ken Ma <make@marvell.com>.
Fix the mpp definitions according to newest revision of the
specification:
- northbridge:
fix pmic1 gpio number to 7
fix pmic0 gpio number to 6
- southbridge
split pcie1 group bit mask to BIT(5) and BIT(9)
fix ptp group bit mask to BIT(11) | BIT(12) | BIT(13)
add smi group with bit mask BIT(4)
[gregory: split the pcie group in 2, as at hardware level they can be
configured separately]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MX8QM contains a system controller that is responsible for controlling
the pad setting of the IPs that are present. Communication between the
host processor running an OS and the system controller happens through
a SCU protocol. This patch adds the SCU based MX8QM pinctrl driver.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No core changes this time.
New drivers:
- NXP (ex Freescale) i.MX 8 QXP SoC driver.
- Mediatek MT6797 SoC driver.
- Mediatek MT7629 SoC driver.
- Actions Semiconductor S700 SoC driver.
- Renesas RZ/A2 SoC driver.
- Allwinner sunxi suniv F1C100 SoC driver.
- Qualcomm PMS405 PMIC driver.
- Microsemi Ocelot Jaguar2 SoC driver.
Improvements:
- Some RT improvements (using raw spinlocks where appropriate).
- A lot of new pin sets on the Renesas PFC pin controllers.
- GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
chips, and Xway.
- Major modernization of the Intel pin control drivers.
- STM32 pin control driver will now synchronize usage of pins
with another CPU using a hardware spinlock.
-----BEGIN PGP SIGNATURE-----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=cm6m
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"We have no core changes but lots of incremental development in drivers
all over the place: Renesas, NXP, Mediatek and Actions Semiconductor
keep churning out new SoCs.
I have some subtree maintainers for Renesas and Intel helping out to
keep down the load, it's been working smoothly (Samsung also have a
subtree but it was not used this cycle.)
New drivers:
- NXP (ex Freescale) i.MX 8 QXP SoC driver.
- Mediatek MT6797 SoC driver.
- Mediatek MT7629 SoC driver.
- Actions Semiconductor S700 SoC driver.
- Renesas RZ/A2 SoC driver.
- Allwinner sunxi suniv F1C100 SoC driver.
- Qualcomm PMS405 PMIC driver.
- Microsemi Ocelot Jaguar2 SoC driver.
Improvements:
- Some RT improvements (using raw spinlocks where appropriate).
- A lot of new pin sets on the Renesas PFC pin controllers.
- GPIO hogs now work on the Qualcomm SPMI/SSBI pin controller GPIO
chips, and Xway.
- Major modernization of the Intel pin control drivers.
- STM32 pin control driver will now synchronize usage of pins with
another CPU using a hardware spinlock"
* tag 'pinctrl-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (145 commits)
dt-bindings: arm: fsl-scu: add imx8qm pinctrl support
pinctrl: freescale: Break dependency on SOC_IMX8MQ for i.MX8MQ
pinctrl: imx-scu: Depend on IMX_SCU
pinctrl: ocelot: Add dependency on HAS_IOMEM
pinctrl: ocelot: add MSCC Jaguar2 support
pinctrl: bcm: ns: support updated DT binding as syscon subnode
dt-bindings: pinctrl: bcm4708-pinmux: rework binding to use syscon
MAINTAINERS: merge at91 pinctrl entries
pinctrl: imx8qxp: break the dependency on SOC_IMX8QXP
pinctrl: uniphier: constify uniphier_pinctrl_socdata
pinctrl: mediatek: improve Kconfig dependencies
pinctrl: msm: mark PM functions as __maybe_unused
dt-bindings: pinctrl: sunxi: Add supply properties
pinctrl: meson: meson8b: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: add the missing GPIO_GROUPs for BOOT and CARD
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8: rename the "gpio" function to "gpio_periphs"
pinctrl: meson: meson8b: fix the GPIO function for the GPIOAO pins
pinctrl: meson: meson8: fix the GPIO function for the GPIOAO pins
pinctrl: sh-pfc: Make pinmux_cfg_reg.var_field_width[] variable-length
...
The CONFIG_SOC_IMX8MQ will go away, so the dependency can be based on
ARCH_MXC && ARM64.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Otherwise building fails with only PINCTRL_IMX_SCU selected:
aarch64-linux-gnu-ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinctrl_sc_ipc_init':
pinctrl-scu.c:(.text+0x10): undefined reference to `imx_scu_get_handle'
aarch64-linux-gnu-ld: pinctrl-scu.c:(.text+0x10): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_get_handle'
aarch64-linux-gnu-ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinconf_get_scu':
pinctrl-scu.c:(.text+0x64): undefined reference to `imx_scu_call_rpc'
aarch64-linux-gnu-ld: pinctrl-scu.c:(.text+0x64): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_call_rpc'
aarch64-linux-gnu-ld: drivers/pinctrl/freescale/pinctrl-scu.o: in function `imx_pinconf_set_scu':
pinctrl-scu.c:(.text+0x104): undefined reference to `imx_scu_call_rpc'
aarch64-linux-gnu-ld: pinctrl-scu.c:(.text+0x104): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `imx_scu_call_rpc'
make: *** [Makefile:1038: vmlinux] Error 1
Signed-off-by: Guido Günther <agx@sigxcpu.or>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As usual the build fails on UM Linux because that thing does
not have IOMEM. Depend on HAS_IOMEM solves the build problem.
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jaguar2 has the same register layout as Ocelot but it has 64 pins, meaning
that there are 2 registers instead of one.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Documentation has been recently updated specifying that pinctrl should
be subnode of the CRU "syscon". Support that by using parent node for
regmap and reading "offset" property from the DT.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARM64 SoC does not encourage people to add more finegrained SoC
config options rather than a single ARCH_<family> in arch Kconfig.
So this patch aims to break the dependency on SOC_IMX8QXP.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove prompts to make all pinctrl cores to non-visible symbols and
make sure the target SoCs would be coupled with the corresponding
cores.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com
Acked-by: Sean Wang <sean.wang@kernel.org>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Without CONFIG_PM_SLEEP, we get annoying warnings about unused functions:
drivers/pinctrl/qcom/pinctrl-msm.c:1082:12: error: 'msm_pinctrl_resume' defined but not used [-Werror=unused-function]
static int msm_pinctrl_resume(struct device *dev)
^~~~~~~~~~~~~~~~~~
drivers/pinctrl/qcom/pinctrl-msm.c:1075:12: error: 'msm_pinctrl_suspend' defined but not used [-Werror=unused-function]
static int msm_pinctrl_suspend(struct device *dev)
Mark them as __maybe_unused to shut up the warning and silently drop
the functions without having to add ugly #ifdefs.
Fixes: 977d057ad3 ("pinctrl: msm: Add sleep pinctrl state transitions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be
configured in devicetree using groups = BOOTx or groups = CARDx. This
makes the behavior consistent with other pins inside the same driver as
well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers.
Fixes: 0fefcb6876 ("pinctrl: Add support for Meson8b")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the BOOT and CARD pins as GROUP_GROUPs as well so they can be
configured in devicetree using groups = BOOTx or groups = CARDx. This
makes the behavior consistent with other pins inside the same driver as
well as with the BOOT and CARD pins of the GXBB and GXL pinctrl drivers.
Fixes: 6ac7309511 ("pinctrl: add driver for Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the existing "gpio" function to "gpio_periphs". This makes it
consistent with the "gpio_aobus" function. Also GXBB and GXL are also
using the "gpio_periphs" naming, so this makes the code here consistent
with other Amlogic pinctrl drivers.
No functional changes since thee "gpio" function is currently not used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the existing "gpio" function to "gpio_periphs". This makes it
consistent with the "gpio_aobus" function. Also GXBB and GXL are also
using the "gpio_periphs" naming, so this makes the code here consistent
with other Amlogic pinctrl drivers.
No functional changes since thee "gpio" function is currently not used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIOAO pins (as well as the two exotic GPIO_BSD_EN and GPIO_TEST_N)
only belong to the pin controller in the AO domain. With the current
definition these pins cannot be referred to in .dts files as group
(which is possible on GXBB and GXL for example).
Add a separate "gpio_aobus" function to fix the mapping between the pin
controller and the GPIO pins in the AO domain. This is similar to how
the GXBB and GXL drivers implement this functionality.
Fixes: 9dab1868ec ("pinctrl: amlogic: Make driver independent from two-domain configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinmux_cfg_reg.var_field_width[] is actually a variable-length array,
terminated by a zero, and counting at most r_width entries.
Usually the number of entries is much smaller than r_width, so the
ability to catch bugs at compile time through an "excess elements in
array initializer" warning is fairly limited.
Hence make the array variable-length, decreasing kernel size slightly.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The debug code in sh_pfc_write_config_reg() prints the width of the
field being modified.
However, registers with a variable-width field layout are identified by
pinmux_cfg_reg.field_width being zero, hence zeroes are printed instead
of the actual field widths.
Fix this by printing the Hamming weight of the field mask instead, which
is correct for both fixed-width and variable-width fields.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Some values in the Peripheral Function Select Register 10 descriptor are
shifted by one position, which may cause a peripheral function to be
programmed incorrectly.
Fixing this makes all HSCIF0 pins use Function 4 (value 3), like was
already the case for the HSCK0 pin in field IP10[5:3].
Fixes: ac1ebc2190 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The IP10[5:3] field in Peripheral Function Select Register 10 has a
width of 3 bits, i.e. it allows programming one out of 8 different
configurations.
However, 9 values are provided instead of 8, overflowing into the
subsequent field in the register, and thus breaking the configuration of
the latter.
Fix this by dropping a bogus zero value.
Fixes: ac1ebc2190 ("sh-pfc: Add sh7734 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Port C I/O Register 0 contains 7 reserved bits, but the descriptor
contains only dummy configuration values for 6 reserved bits, thus
breaking the configuration of all subsequent fields in the register.
Fix this by adding the two missing configuration values.
Fixes: f5e811f2a4 ("sh-pfc: Add sh7269 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Port F Control Register 3 (PFCR3) contains only a single field.
However, counting from left to right, it is the fourth field, not the
first field.
Insert the missing dummy configuration values (3 fields of 16 values) to
fix this.
The descriptor for the Port F Control Register 0 (PFCR0) lacks the
description for the 4th field (PF0 Mode, PF0MD[2:0]).
Add the missing configuration values to fix this.
Fixes: a8d42fc421 ("sh-pfc: Add sh7264 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
While the SEL_PWM[0-3] fields in the Module Select Register 0 support 4
possible configurations per PWM pin, only the first 3 are valid.
Replace the invalid and unused configurations for SEL_PWM[0-3]_3 by
dummies.
Fixes: 794a671176 ("pinctrl: sh-pfc: Initial R8A77995 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The SEL_I2C1 (MOD_SEL0[21:20]) field in Module Select Register 0 has a
width of 2 bits, i.e. it allows programming one out of 4 different
configurations.
However, the MOD_SEL0_21_20 macro contains 8 values instead of 4,
overflowing into the subsequent fields in the register, and thus breaking
the configuration of the latter.
Fix this by dropping the bogus last 4 values, including the non-existent
SEL_I2C1_4 configuration.
Fixes: 6d4036a1e3 ("pinctrl: sh-pfc: Initial R8A77990 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Peripheral Function Select Register 11 contains 3 reserved bits and
15 variable-width fields, but the variable field descriptor does not
contain the 3-bit field IP11[25:23].
Fixes: 856cb4bb33 ("sh: Add support pinmux for SH7734")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Module Select Register 0 contains 20 (= 5 x 4) reserved bits, and 12
single-bit fields, but the variable field descriptor lacks a field of 4
reserved bits.
Fixes: f59125248a ("pinctrl: sh-pfc: Add R8A77980 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Module Select Register 0 contains 20 (= 5 x 4) reserved bits, and 12
single-bit fields, but the variable field descriptor lacks a field of 4
reserved bits.
Fixes: b92ac66a18 ("pinctrl: sh-pfc: Add R8A77970 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The Peripheral Function Select Register 9 contains 12 fields, but the
variable field descriptor contains a 13th bogus field of 3 bits.
Fixes: 43c4436e2f ("pinctrl: sh-pfc: add R8A7794 PFC support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Add a build-time check, to ensure the number of pins and pin marks in a
pin group matches. This helps catching bugs early.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The tpu4_to3_mux[] array contains the TPU4TO3 pin mark, but the
tpu4_to3_pins[] array lacks the corresponding pin number.
Add the missing pin number, for non-GPIO pin F26.
Fixes: 5da4eb049d ("sh-pfc: sh73a0: Add TPU pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The vin1_b_data18_mux[] arrays contains pin marks for the 2 LSB bits of
the color components. The vin1_b_data18_pins[] array rightfully does
not include the corresponding pin numbers, as RGB18 is subset of RGB24,
containing only the 6 MSB bits of each component.
Fixes: 8e32c9671f ("pinctrl: sh-pfc: r8a7791: Add VIN pins")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The qspi_data4_b_mux[] array contains pin marks for the clock and chip
select pins. The qspi_data4_b_pins[] array rightfully does not contain
the corresponding pin numbers, as the control pins are provided by a
separate group (qspi_ctrl_b).
Fixes: 2d0c386f13 ("pinctrl: sh-pfc: r8a7791: Add QSPI pin groups")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The lcd0_data24_1_pins[] array contains the LCD0 D1[2-5] pin numbers,
but the lcd0_data24_1_mux[] array lacks the corresponding pin marks.
Fixes: 06c7dd866d ("sh-pfc: r8a7740: Add LCDC0 and LCDC1 pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
The gether_gmii_mux[] array contains the REF125CK pin mark, but the
gether_gmii_pins[] array lacks the corresponding pin number.
Fixes: bae11d30d0 ("sh-pfc: r8a7740: Add GETHER pin groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Due to an interaction with commit 9f2b76a2db ("pinctrl: sh-pfc:
r8a77990: Add R8A774C0 PFC support"), the state of the I/O Control
Registers is saved/restored during s2ram on RZ/G2E, but not on R-Car E3.
Hence on R-Car E3, SDHI voltage state is lost after system resume.
Fix this by registering the I/O Control Registers on R-Car E3, too.
Fixes: 33847a7137 ("pinctrl: sh-pfc: r8a77990: Add voltage switch operations for SDHI")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
devm_kasprintf() may return NULL on failure of internal allocation
thus the assignments are not safe if not checked. On error
rza1_pinctrl_register() respectively rza1_parse_gpiochip() return
negative values so -ENOMEM in the (unlikely) failure case of
devm_kasprintf() should be fine here.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Fixes: 5a49b644b3 ("pinctrl: Renesas RZ/A1 pin and gpio controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The R-Car Gen3 HardWare Manual Errata for Rev. 1.00 (Jul 2, 2018) states
that the USB30_OVC pin supports pull-up only. It has a bit assigned in
the pull-enable register (PUEN5), but not in the pull-up/down control
register (PUD5).
Add a check for this, to prevent configuring a prohibited setting.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 83f6941a42 ("pinctrl: sh-pfc: r8a77990: Add bias pinconf support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
This patch is based on commit a86caa9ba5 ("pinctrl: msm: fix gpio-hog
related boot issues").
It fixes the issue that the gpio ranges needs to be defined before
gpiochip_add().
Therefore, we also have to swap the order of registering the pinctrl
driver and registering the gpio chip.
You also have to add the "gpio-ranges" property to the pinctrl device
node to get it finally working.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang does not support this option:
warning: unknown warning option '-Woverride-init'; did you mean
'-Woverride-module'? [-Wunknown-warning-option]
1 warning generated.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
