Support to individually control Media/Render well based on the register access.
Add CHV specific write function to habdle difference between registers
that are sadowed vs those that need forcewake even for writes.
Streamline the CHV forcewake functions just like was done for VLV.
This will also fix a bug in accessing the common well registers,
where we'd end up trying to wake up the wells too many times
since we'd call force_wake_get/put twice per register access, with
FORCEFAKE_ALL both times.
v2: Drop write FIFO for CHV and add comman well forcewake (Ville)
Re-factor CHV/VLV Forcewake offsets (Ben)
v3: Fix for decrementing fw count in chv read/write. (Deepak)
v4: Squash the patches (Mika)
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
[vsyrjala: Move the register range macros into intel_uncore.c]
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Configure PCBR if BIOS fails allocate pcbr (deepak)
v3: Fix PCBR condition check during CHV RC6 Enable flag set
v4: Fixup PCBR comment msg. (Chris)
Rebase against latest code (Deak)
Fixup Spurious hunk (Ben)
v5: Fix PCBR and commentis msg (mika)
v6: Rebase patch on latest nightly (Deepak)
Signed-off-by: Deepak S <deepak.s@linux.intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
"Because our driver assumes only one panel is PSR capable, and we
already have other PSR information on dev_priv instead of intel_dp. If
we ever support multiple PSR panels, we'll have to move struct
i915_psr to intel_dp anyway." (by Paulo)
v2: Avoid more than one setup. Removing initialization
and trusting allocation. (By Paulo Zanoni).
v3: rebase.
v4: Adding comment.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
display rework fixes lots of displayport issues.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (43 commits)
drm/nouveau/disp/dp: fix tmds passthrough on dp connector
drm/nouveau/dp: probe dpcd to determine connectedness
drm/nv50-: trigger update after all connectors disabled
drm/nv50-: prepare for attaching a SOR to multiple heads
drm/gf119-/disp: fix debug output on update failure
drm/nouveau/disp/dp: make use of postcursor when its available
drm/g94-/disp/dp: take max pullup value across all lanes
drm/nouveau/bios/dp: parse lane postcursor data
drm/nouveau/dp: fix support for dpms
drm/nouveau: register a drm_dp_aux channel for each dp connector
drm/g94-/disp: add method to power-off dp lanes
drm/nouveau/disp/dp: maintain link in response to hpd signal
drm/g94-/disp: bash and wait for something after changing lane power regs
drm/nouveau/disp/dp: split link config/power into two steps
drm/nv50/disp: train PIOR-attached DP from second supervisor
drm/nouveau/disp/dp: make use of existing output data for link training
drm/gf119/disp: start removing direct vbios parsing from supervisor
drm/nv50/disp: start removing direct vbios parsing from supervisor
drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
drm/nouveau/disp/dp: create subclass for dp outputs
...
We were sending the necessary state changes to unset the mode, but
never actually hit the big GO button unless another modeset happens
afterwards.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
SOR_PWR has no effect to power-off DP links, unlike other SOR protocols.
Instead, on the source side, we cut power to the lanes after having put
the sink into D3. Link training takes care of everything required to
bring it back again.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This previously worked for the most part due to userspace doing a
modeset in response to HPD interrupts. This will allow us to
properly handle cases where sync is lost for other reasons, or if
userspace isn't caring.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This will, at some point, be used to replace various bits and pieces of
code doing direct bios parsing. For now, it'll just be used for some
DP improvements.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's also provisions to allow a pad to be locked with a specific
routing, for an indefinite period of time. This will be used in
future patches.
The G94+ pad driver will now also power-down pads when not required.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This was a half-finished hack before, just enough to handle the shared
aux/i2c pad thing on G94 and up.
We got lucky with locking etc up until now, as this was (generally) all
protected by the DRM mode_config lock. It's about to become a lot more
likely to hit the races.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Re-uses the implementation's accessor functions rather than requiring
and init/fini implementation for each chipset.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There's really not a great deal this time due to me spending most of this window on Maxwell. But, here's the random bits and pieces that's currently queued.
* 'drm-nouveau-next' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (25 commits)
drm/gk208/gr: add missing registers to grctx init
drm/nouveau/kms/nv04-nv40: fix pageflip events via special case.
drm/nv50-/mc: fix kms pageflip events by reordering irq handling order.
drm/nouveau/disp/nv04-nv40: abort scanoutpos query on vga analog.
drm/nv50-/kms: wait for enough ring space in crtc_prepare()
drm/nouveau/disp/dp: support training pattern 3
drm/nouveau/disp/dp: support aux read interval during link training
drm/gk104/gpio: fix incorrect interrupt register usage
drm/nouveau/core: punt all object state change messages to trace level
drm/nouveau/clk: allow end-user reclocking for nv40, nvaa, and nve0 clock types
drm/nouveau/fb: default NvMemExec to on, turning it off is used for debugging only
drm/nouveau/bios: fix a potential NULL deref in the PROM shadowing function
drm/nouveau/i2c: bump the i2c delay for the adt7473
drm/nouveau/therm/fan/tach: default to 2 pulses per revolution
drm/nvf0/device: enable video decoding engines on gk110/gk208
drm/nvf1/device: add support for 0xf1 (gk110b)
drm/nouveau/device: support for probing GK20A
drm/nouveau/graph: add GK20A support
drm/nouveau/graph: pad firmware code at load time
drm/nouveau/graph: enable when using external fw
...
This fixes hangs on GK208 which happen instantaneously on trying to use a
geometry shader.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org # v3.14+
Cards with nv04 display engine can't reliably use vblank
counts and timestamps computed via drm_handle_vblank(), as
the function gets invoked after sending the pageflip events.
Fix this by defaulting to the old crtcid = -1 fallback path
on <= NV-50 cards, and only using the precise path on NV-50
and later.
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Cc: <stable@vger.kernel.org> # 3.13+
