Commit Graph

1267 Commits

Author SHA1 Message Date
Christer Beskow
1910cd8853 can: kvaser_pciefd: kvaser_pciefd_pwm_stop(): remove unnecessary code when setting pwm duty cycle to zero
To set the duty cycle to zero (i.e. pwm_stop), the trigger value shall
be equal to the top value.

This is achieved by reading the value of the top bit field from the pwm
register and then writing back this value to the trigger and top bit
fields.

Addresses-Coverity: ("Logically dead code")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-13 16:36:52 +02:00
David S. Miller
13dfb3fa49 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Just minor overlapping changes in the conflicts here.

Signed-off-by: David S. Miller <davem@davemloft.net>
2019-08-06 18:44:57 -07:00
Linus Torvalds
33920f1ec5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from David Miller:
 "Yeah I should have sent a pull request last week, so there is a lot
  more here than usual:

   1) Fix memory leak in ebtables compat code, from Wenwen Wang.

   2) Several kTLS bug fixes from Jakub Kicinski (circular close on
      disconnect etc.)

   3) Force slave speed check on link state recovery in bonding 802.3ad
      mode, from Thomas Falcon.

   4) Clear RX descriptor bits before assigning buffers to them in
      stmmac, from Jose Abreu.

   5) Several missing of_node_put() calls, mostly wrt. for_each_*() OF
      loops, from Nishka Dasgupta.

   6) Double kfree_skb() in peak_usb can driver, from Stephane Grosjean.

   7) Need to hold sock across skb->destructor invocation, from Cong
      Wang.

   8) IP header length needs to be validated in ipip tunnel xmit, from
      Haishuang Yan.

   9) Use after free in ip6 tunnel driver, also from Haishuang Yan.

  10) Do not use MSI interrupts on r8169 chips before RTL8168d, from
      Heiner Kallweit.

  11) Upon bridge device init failure, we need to delete the local fdb.
      From Nikolay Aleksandrov.

  12) Handle erros from of_get_mac_address() properly in stmmac, from
      Martin Blumenstingl.

  13) Handle concurrent rename vs. dump in netfilter ipset, from Jozsef
      Kadlecsik.

  14) Setting NETIF_F_LLTX on mac80211 causes complete breakage with
      some devices, so revert. From Johannes Berg.

  15) Fix deadlock in rxrpc, from David Howells.

  16) Fix Kconfig deps of enetc driver, we must have PHYLIB. From Yue
      Haibing.

  17) Fix mvpp2 crash on module removal, from Matteo Croce.

  18) Fix race in genphy_update_link, from Heiner Kallweit.

  19) bpf_xdp_adjust_head() stopped working with generic XDP when we
      fixes generic XDP to support stacked devices properly, fix from
      Jesper Dangaard Brouer.

  20) Unbalanced RCU locking in rt6_update_exception_stamp_rt(), from
      David Ahern.

  21) Several memory leaks in new sja1105 driver, from Vladimir Oltean"

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (214 commits)
  net: dsa: sja1105: Fix memory leak on meta state machine error path
  net: dsa: sja1105: Fix memory leak on meta state machine normal path
  net: dsa: sja1105: Really fix panic on unregistering PTP clock
  net: dsa: sja1105: Use the LOCKEDS bit for SJA1105 E/T as well
  net: dsa: sja1105: Fix broken learning with vlan_filtering disabled
  net: dsa: qca8k: Add of_node_put() in qca8k_setup_mdio_bus()
  net: sched: sample: allow accessing psample_group with rtnl
  net: sched: police: allow accessing police->params with rtnl
  net: hisilicon: Fix dma_map_single failed on arm64
  net: hisilicon: fix hip04-xmit never return TX_BUSY
  net: hisilicon: make hip04_tx_reclaim non-reentrant
  tc-testing: updated vlan action tests with batch create/delete
  net sched: update vlan action for batched events operations
  net: stmmac: tc: Do not return a fragment entry
  net: stmmac: Fix issues when number of Queues >= 4
  net: stmmac: xgmac: Fix XGMAC selftests
  be2net: disable bh with spin_lock in be_process_mcc
  net: cxgb3_main: Fix a resource leak in a error path in 'init_one()'
  net: ethernet: sun4i-emac: Support phy-handle property for finding PHYs
  net: bridge: move default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
  ...
2019-08-06 17:11:59 -07:00
Tomas Bortoli
ead16e53c2 can: peak_usb: pcan_usb_pro: Fix info-leaks to USB devices
Uninitialized Kernel memory can leak to USB devices.

Fix by using kzalloc() instead of kmalloc() on the affected buffers.

Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+d6a5a1a3657b596ef132@syzkaller.appspotmail.com
Fixes: f14e22435a ("net: can: peak_usb: Do not do dma on the stack")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-02 13:58:01 +02:00
Tomas Bortoli
30a8beeb30 can: peak_usb: pcan_usb_fd: Fix info-leaks to USB devices
Uninitialized Kernel memory can leak to USB devices.

Fix by using kzalloc() instead of kmalloc() on the affected buffers.

Signed-off-by: Tomas Bortoli <tomasbortoli@gmail.com>
Reported-by: syzbot+513e4d0985298538bf9b@syzkaller.appspotmail.com
Fixes: 0a25e1f4f1 ("can: peak_usb: add support for PEAK new CANFD USB adapters")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-02 13:57:48 +02:00
Wang Xiayang
e787f19373 can: peak_usb: force the string buffer NULL-terminated
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string is
passed to dev_info() which relies on the NULL-termination.

Use strlcpy() instead.

This issue is identified by a Coccinelle script.

Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-02 13:27:30 +02:00
Wang Xiayang
cd28aa2e05 can: sja1000: force the string buffer NULL-terminated
strncpy() does not ensure NULL-termination when the input string size
equals to the destination buffer size IFNAMSIZ. The output string
'name' is passed to dev_info which relies on NULL-termination.

Use strlcpy() instead.

This issue is identified by a Coccinelle script.

Signed-off-by: Wang Xiayang <xywang.sjtu@sjtu.edu.cn>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-08-02 13:26:10 +02:00
Stephen Boyd
d1a55841ab net: Remove dev_err() usage after platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.

// <smpl>
@@
expression ret;
struct platform_device *E;
@@

ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);

if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>

While we're here, remove braces on if statements that only have one
statement (manually).

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: netdev@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-30 14:37:35 -07:00
Gustavo A. R. Silva
5a8dadbcfa can: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

This patch fixes the following warnings:

drivers/net/can/peak_canfd/peak_pciefd_main.c:668:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/spi/mcp251x.c:875:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:895:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:953:15: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c: In function ‘pcan_usb_decode_error’:
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (n & PCAN_USB_ERROR_BUS_LIGHT) {
      ^
drivers/net/can/usb/peak_usb/pcan_usb.c:428:2: note: here
  case CAN_STATE_ERROR_WARNING:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.

Notice that in some cases spelling mistakes were fixed.
In other cases, the /* fall through */ comment is placed
at the bottom of the case statement, which is what GCC
is expecting to find.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
2019-07-25 20:09:42 -05:00
Stephane Grosjean
fee6a8923a can: peak_usb: fix potential double kfree_skb()
When closing the CAN device while tx skbs are inflight, echo skb could
be released twice. By calling close_candev() before unlinking all
pending tx urbs, then the internal echo_skb[] array is fully and
correctly cleared before the USB write callback and, therefore,
can_get_echo_skb() are called, for each aborted URB.

Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:16:31 +02:00
Joakim Zhang
5f186c257f can: flexcan: fix stop mode acknowledgment
To enter stop mode, the CPU should manually assert a global Stop Mode
request and check the acknowledgment asserted by FlexCAN. The CPU must
only consider the FlexCAN in stop mode when both request and
acknowledgment conditions are satisfied.

Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:16:31 +02:00
Wen Yang
e9f2a856e1 can: flexcan: fix an use-after-free in flexcan_setup_stop_mode()
The gpr_np variable is still being used in dev_dbg() after the
of_node_put() call, which may result in use-after-free.

Fixes: de3578c198 ("can: flexcan: add self wakeup support")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: linux-stable <stable@vger.kernel.org> # >= v5.0
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:16:31 +02:00
Weitao Hou
375f755899 can: mcp251x: add error check when wq alloc failed
add error check when workqueue alloc failed, and remove redundant code
to make it clear.

Fixes: e0000163e3 ("can: Driver for the Microchip MCP251x SPI CAN controllers")
Signed-off-by: Weitao Hou <houweitaoo@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:10:15 +02:00
Nikita Yushchenko
d4b890aec4 can: rcar_canfd: fix possible IRQ storm on high load
We have observed rcar_canfd driver entering IRQ storm under high load,
with following scenario:
- rcar_canfd_global_interrupt() in entered due to Rx available,
- napi_schedule_prep() is called, and sets NAPIF_STATE_SCHED in state
- Rx fifo interrupts are masked,
- rcar_canfd_global_interrupt() is entered again, this time due to
  error interrupt (e.g. due to overflow),
- since scheduled napi poller has not yet executed, condition for calling
  napi_schedule_prep() from rcar_canfd_global_interrupt() remains true,
  thus napi_schedule_prep() gets called and sets NAPIF_STATE_MISSED flag
  in state,
- later, napi poller function rcar_canfd_rx_poll() gets executed, and
  calls napi_complete_done(),
- due to NAPIF_STATE_MISSED flag in state, this call does not clear
  NAPIF_STATE_SCHED flag from state,
- on return from napi_complete_done(), rcar_canfd_rx_poll() unmasks Rx
  interrutps,
- Rx interrupt happens, rcar_canfd_global_interrupt() gets called
  and calls napi_schedule_prep(),
- since NAPIF_STATE_SCHED is set in state at this time, this call
  returns false,
- due to that false return, rcar_canfd_global_interrupt() returns
  without masking Rx interrupt
- and this results into IRQ storm: unmasked Rx interrupt happens again
  and again is misprocessed in the same way.

This patch fixes that scenario by unmasking Rx interrupts only when
napi_complete_done() returns true, which means it has cleared
NAPIF_STATE_SCHED in state.

Fixes: dd3bd23eb4 ("can: rcar_canfd: Add Renesas R-Car CAN FD driver")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:07:57 +02:00
Rasmus Villemoes
c63845609c can: dev: call netif_carrier_off() in register_candev()
CONFIG_CAN_LEDS is deprecated. When trying to use the generic netdev
trigger as suggested, there's a small inconsistency with the link
property: The LED is on initially, stays on when the device is brought
up, and then turns off (as expected) when the device is brought down.

Make sure the LED always reflects the state of the CAN device.

Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 11:06:39 +02:00
Jeroen Hofstee
4c7f715485 can: ti_hecc: use timestamp based rx-offloading
As already mentioned in [1] and included in [2], there is an off by one
issue since the high bank is already enabled when the _next_ mailbox to
be read has index 12, so the mailbox being read was 13. The message can
therefore go into mailbox 31 and the driver will be repolled until the
mailbox 12 eventually receives a msg. Or the message might end up in the
12th mailbox, but then it would become disabled after reading it and only
be enabled again in the next "round" after mailbox 13 was read, which can
cause out of order messages, since the lower priority mailboxes can
accept messages in the meantime.

As mentioned in [3] there is a hardware race condition when changing the
CANME register while messages are being received. Even when including a
busy poll on reception, like in [2] there are still overflows and out of
order messages at times, but less then without the busy loop polling.
Unlike what the patch suggests, the polling time is not in the microsecond
range, but takes as long as a current CAN bus reception needs to finish,
so typically more in the fraction of millisecond range. Since the timeout
is in jiffies it won't timeout.

Even with these additional fixes the driver is still not able to provide a
proper FIFO which doesn't drop packages. So change the driver to use
rx-offload and base order on timestamp instead of message box numbers. As
a side affect, this also fixes [4] and [5].

Before this change messages with a single byte counter were dropped /
received out of order at a bitrate of 250kbit/s on an am3517. With this
patch that no longer occurs up to and including 1Mbit/s.

[1] https://linux-can.vger.kernel.narkive.com/zgO9inVi/patch-can-ti-hecc-fix-rx-wrong-sequence-issue#post6
[2] http://arago-project.org/git/projects/?p=linux-omap3.git;a=commit;h=02346892777f07245de4d5af692513ebd852dcb2
[3] https://linux-can.vger.kernel.narkive.com/zgO9inVi/patch-can-ti-hecc-fix-rx-wrong-sequence-issue#post5
[4] https://patchwork.ozlabs.org/patch/895956/
[5] https://www.spinics.net/lists/netdev/msg494971.html

Cc: Anant Gole <anantgole@ti.com>
Cc: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:55 +02:00
Sean Nyekjaer
915f966642 can: flexcan: add support for DT property 'wakeup-source'
The flexcan controller can be forced as a wakeup source by
stating that explicitly in the device's .dts file using the
"wakeup-source" boolean property.

Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:55 +02:00
Dong Aisheng
8c306bec2d can: flexcan: add support for PE clock source select
Add support to select the clock source for CAN Protocol Engine (PE).
It's SoC Implementation dependent. Refer to RM for detailed definition
of each SoC. We select clock source 1 (peripheral clock) by default in
driver now, this patch adds support to parse the clock source from the DT.

Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:55 +02:00
Aisheng Dong
ca10989632 can: flexcan: implement can Runtime PM
Flexcan will be disabled during suspend if no wakeup function required and
enabled after resume accordingly. During this period, we could explicitly
disable clocks.
Since PM is optional, the clock is enabled at probe to guarante the
clock is running when PM is not enabled in the kernel.

Implement Runtime PM which will:
1) Without CONFIG_PM, clock is running whether Flexcan up or down.
2) With CONFIG_PM, clock enabled while Flexcan up and disabled when
   Flexcan down.
3) Disable clock when do system suspend and enable clock while system
   resume.
4) Make Power Domain framework be able to shutdown the corresponding
   power domain of this device.

Signed-off-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:55 +02:00
Colin Ian King
64d6ce8fe4 can: xilinx_can: clean up indentation issue
A statement is indented one level too deep, fix this.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:55 +02:00
Appana Durga Kedareswara rao
c223da6893 can: xilinx_can: Add support for CANFD FD frames
CANFD IP supports both CAN and CAN FD frames,
Existing driver supports only CAN frames, This patch
adds support for CAN FD frames.

Signed-off-by: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Appana Durga Kedareswara rao
8dce7ea41a can: xilinx_can: Add cantype parameter in xcan_devtype_data struct
To differentiate between different CAN IP's this patch adds
cantype enum variable in the xcan_devtype_data structure

Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Appana Durga Kedareswara rao
3281b380ec can: xilinx_can: Fix flags field initialization for axi can and canps
AXI CAN IP and CANPS IP supports tx fifo empty feature, this patch updates
the flags field for the same.

Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Appana Durga Kedareswara rao
c942a575b9 can: xilinx_can: Fix kernel doc warnings
This patch fixes below kernel doc warnings
warning: Function parameter or member 'priv' not described in
'xcan_write_frame'
warning: Function parameter or member 'skb' not described in
'xcan_start_xmit_fifo'
warning: Function parameter or member 'ndev' not described in
'xcan_start_xmit_fifo'
warning: Function parameter or member 'skb' not described in
'xcan_start_xmit_mailbox'
warning: Function parameter or member 'ndev' not described in
'xcan_start_xmit_mailbox'
warning: Function parameter or member 'priv' not described in
'xcan_rx_fifo_get_next_frame'

Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Appana Durga Kedareswara rao
d38f9180da can: xilinx_can: Fix style issues
This patch fixes below checkpatch warnings and checks in the driver.

CHECK: Alignment should match open parenthesis
+       void (*write_reg)(const struct xcan_priv *priv, enum xcan_reg reg,
+                       u32 val);

CHECK: Alignment should match open parenthesis
+static void xcan_write_reg_le(const struct xcan_priv *priv, enum xcan_reg reg,
+                       u32 val)

CHECK: Alignment should match open parenthesis
+static void xcan_write_reg_be(const struct xcan_priv *priv, enum xcan_reg reg,
+                       u32 val)

CHECK: Alignment should match open parenthesis
+       netdev_dbg(ndev, "BRPR=0x%08x, BTR=0x%08x\n",
+                       priv->read_reg(priv, XCAN_BRPR_OFFSET),

CHECK: Alignment should match open parenthesis
+                       netdev_warn(ndev,
+                               "timed out for correct mode\n");

CHECK: Alignment should match open parenthesis
+       netdev_dbg(ndev, "status:#x%08x\n",
+                       priv->read_reg(priv, XCAN_SR_OFFSET));

CHECK: spaces preferred around that '-' (ctx:VxV)
+                       (CAN_EFF_ID_BITS-CAN_SFF_ID_BITS)) <<
                                        ^

CHECK: Alignment should match open parenthesis
+       netdev_dbg(ndev, "%s: error status register:0x%x\n",
+                       __func__, priv->read_reg(priv, XCAN_ESR_OFFSET));

WARNING: line over 80 characters
+                       offset = XCAN_RXMSG_2_FRAME_OFFSET(fsr & XCAN_FSR_RI_MASK);

WARNING: line over 80 characters
+                       offset = XCAN_RXMSG_FRAME_OFFSET(fsr & XCAN_FSR_RI_MASK);

WARNING: line over 80 characters
+               while ((isr & XCAN_IXR_TXOK_MASK) && !WARN_ON(++retries == 100)) {

WARNING: line over 80 characters
+                       priv->write_reg(priv, XCAN_ICR_OFFSET, XCAN_IXR_TXOK_MASK);

CHECK: Alignment should match open parenthesis
+               netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+                               __func__, ret);

CHECK: Alignment should match open parenthesis
+       ret = request_irq(ndev->irq, xcan_interrupt, priv->irq_flags,
+                       ndev->name, ndev);

CHECK: Alignment should match open parenthesis
+static int xcan_get_berr_counter(const struct net_device *ndev,
+                                       struct can_berr_counter *bec)

CHECK: Alignment should match open parenthesis
+               netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+                               __func__, ret);

CHECK: Please don't use multiple blank lines
+
+

CHECK: Alignment should match open parenthesis
+               netdev_err(ndev, "%s: pm_runtime_get failed(%d)\n",
+                       __func__, ret);`

Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Dan Murphy
5443c226ba can: tcan4x5x: Add tcan4x5x driver to the kernel
Add the TCAN4x5x SPI CAN driver.

This device uses the Bosch MCAN IP core along with a SPI interface map.
Register to the MCAN common core code to manage the MCAN IP.

This device has a special method to indicate a write/read operation on
the data payload.

Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Dan Murphy
441ac34016 can: m_can: Rename m_can_priv to m_can_classdev
Rename the common m_can_priv class structure to m_can_classdev as this
is more descriptive.

Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Dan Murphy
f524f829b7 can: m_can: Create a m_can platform framework
Create a m_can platform framework that peripheral
devices can register to and use common code and register sets.
The peripheral devices may provide read/write and configuration
support of the IP.

Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Dan Murphy
69652195b6 can: m_can: Fix checkpatch issues on existing code
Fix checkpatch issues found during the m_can framework creation, before
framework creation in the following patches.

Fix these 4 check issues:
CHECK: Unnecessary parentheses around 'cdev->can.state != CAN_STATE_ERROR_WARNING'
	if (psr & PSR_EW &&
	    (cdev->can.state != CAN_STATE_ERROR_WARNING)) {

CHECK: Unnecessary parentheses around 'cdev->can.state != CAN_STATE_ERROR_PASSIVE'
	if ((psr & PSR_EP) &&
	    (cdev->can.state != CAN_STATE_ERROR_PASSIVE)) {

CHECK: Unnecessary parentheses around 'cdev->can.state != CAN_STATE_BUS_OFF'
	if ((psr & PSR_BO) &&
	    (cdev->can.state != CAN_STATE_BUS_OFF)) {

CHECK: Unnecessary parentheses around 'priv->version <= 31'
	if ((priv->version <= 31) && (irqstatus & IR_MRAF) &&
	    (m_can_read(priv, M_CAN_ECR) & ECR_RP)) {

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Gustavo A. R. Silva
b07fbf2397 can: mark expected switch fall-throughs
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

This patch fixes the following warnings:

drivers/net/can/peak_canfd/peak_pciefd_main.c:668:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/spi/mcp251x.c:875:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:895:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/at91_can.c:953:15: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/net/can/usb/peak_usb/pcan_usb.c: In function ‘pcan_usb_decode_error’:
drivers/net/can/usb/peak_usb/pcan_usb.c:422:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (n & PCAN_USB_ERROR_BUS_LIGHT) {
      ^
drivers/net/can/usb/peak_usb/pcan_usb.c:428:2: note: here
  case CAN_STATE_ERROR_WARNING:
  ^~~~

Warning level 3 was used: -Wimplicit-fallthrough=3

This patch is part of the ongoing efforts to enabling
-Wimplicit-fallthrough.

Notice that in some cases spelling mistakes were fixed.
In other cases, the /* fall through */ comment is placed
at the bottom of the case statement, which is what GCC
is expecting to find.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # for the at91_can.c
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:54 +02:00
Henning Colliander
26ad340e58 can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices
This patch adds support for Kvaser PCIEcan devices. This includes
support for up to 4 CAN channels on a single card, depending on device.

Signed-off-by: Henning Colliander <henning.colliander@evidente.se>
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:53 +02:00
Gustavo A. R. Silva
d9e5d174ad can: kvaser_usb: Use struct_size() in alloc_candev()
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

instance = alloc(sizeof(struct foo) + count * sizeof(void *));

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = alloc(struct_size(instance, entry, count));

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:31:53 +02:00
Ji-Ze Hong (Peter Hong)
2d91fdccad can: sja1000: f81601: add Fintek F81601 support
This patch add support for Fintek PCIE to 2 CAN controller support

Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 10:30:37 +02:00
Marc Kleine-Budde
4dfc39e1b6 can: sja1000: Makefile/Kconfig: sort alphabetically
This patch sorts the drivers in the Makefile alphabetically and arranges
the Kconfig file accordingly.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-07-24 08:50:18 +02:00
Fuqian Huang
233cc605a2 net/can: using dev_get_drvdata directly
Several drivers cast a struct device pointer to a struct
platform_device pointer only to then call platform_get_drvdata().
To improve readability, these constructs can be simplified
by using dev_get_drvdata() directly.

Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-05 15:24:41 -07:00
Linus Torvalds
c884d8ac7f SPDX update for 5.2-rc6
Another round of SPDX updates for 5.2-rc6
 
 Here is what I am guessing is going to be the last "big" SPDX update for
 5.2.  It contains all of the remaining GPLv2 and GPLv2+ updates that
 were "easy" to determine by pattern matching.  The ones after this are
 going to be a bit more difficult and the people on the spdx list will be
 discussing them on a case-by-case basis now.
 
 Another 5000+ files are fixed up, so our overall totals are:
 	Files checked:            64545
 	Files with SPDX:          45529
 
 Compared to the 5.1 kernel which was:
 	Files checked:            63848
 	Files with SPDX:          22576
 This is a huge improvement.
 
 Also, we deleted another 20000 lines of boilerplate license crud, always
 nice to see in a diffstat.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyQYA8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ymnGQCghETUBotn1p3hTjY56VEs6dGzpHMAnRT0m+lv
 kbsjBGEJpLbMRB2krnaU
 =RMcT
 -----END PGP SIGNATURE-----

Merge tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx

Pull still more SPDX updates from Greg KH:
 "Another round of SPDX updates for 5.2-rc6

  Here is what I am guessing is going to be the last "big" SPDX update
  for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
  that were "easy" to determine by pattern matching. The ones after this
  are going to be a bit more difficult and the people on the spdx list
  will be discussing them on a case-by-case basis now.

  Another 5000+ files are fixed up, so our overall totals are:
	Files checked:            64545
	Files with SPDX:          45529

  Compared to the 5.1 kernel which was:
	Files checked:            63848
	Files with SPDX:          22576

  This is a huge improvement.

  Also, we deleted another 20000 lines of boilerplate license crud,
  always nice to see in a diffstat"

* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
  treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
  ...
2019-06-21 09:58:42 -07:00
Thomas Gleixner
d2912cb15b treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19 17:09:55 +02:00
Thomas Gleixner
aaa7cb268c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the version 2 of the gnu general public
  license as published by the free software foundation this program is
  distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 10 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.259525894@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-19 17:09:52 +02:00
Linus Torvalds
da0f382029 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Pull networking fixes from David Miller:
 "Lots of bug fixes here:

   1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.

   2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
      Crispin.

   3) Use after free in psock backlog workqueue, from John Fastabend.

   4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
      Salem.

   5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.

   6) Network header needs to be set for packet redirect in nfp, from
      John Hurley.

   7) Fix udp zerocopy refcnt, from Willem de Bruijn.

   8) Don't assume linear buffers in vxlan and geneve error handlers,
      from Stefano Brivio.

   9) Fix TOS matching in mlxsw, from Jiri Pirko.

  10) More SCTP cookie memory leak fixes, from Neil Horman.

  11) Fix VLAN filtering in rtl8366, from Linus Walluij.

  12) Various TCP SACK payload size and fragmentation memory limit fixes
      from Eric Dumazet.

  13) Use after free in pneigh_get_next(), also from Eric Dumazet.

  14) LAPB control block leak fix from Jeremy Sowden"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
  lapb: fixed leak of control-blocks.
  tipc: purge deferredq list for each grp member in tipc_group_delete
  ax25: fix inconsistent lock state in ax25_destroy_timer
  neigh: fix use-after-free read in pneigh_get_next
  tcp: fix compile error if !CONFIG_SYSCTL
  hv_sock: Suppress bogus "may be used uninitialized" warnings
  be2net: Fix number of Rx queues used for flow hashing
  net: handle 802.1P vlan 0 packets properly
  tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
  tcp: add tcp_min_snd_mss sysctl
  tcp: tcp_fragment() should apply sane memory limits
  tcp: limit payload size of sacked skbs
  Revert "net: phylink: set the autoneg state in phylink_phy_change"
  bpf: fix nested bpf tracepoints with per-cpu data
  bpf: Fix out of bounds memory access in bpf_sk_storage
  vsock/virtio: set SOCK_DONE on peer shutdown
  net: dsa: rtl8366: Fix up VLAN filtering
  net: phylink: set the autoneg state in phylink_phy_change
  net: add high_order_alloc_disable sysctl/static key
  tcp: add tcp_tx_skb_cache sysctl
  ...
2019-06-17 15:55:34 -07:00
Fabio Estevam
eb503004a7 can: flexcan: Remove unneeded registration message
Currently the following message is observed when the flexcan
driver is probed:

flexcan 2090000.flexcan: device registered (reg_base=(ptrval), irq=23)

The reason for printing 'ptrval' is explained at
Documentation/core-api/printk-formats.rst:

"Pointers printed without a specifier extension (i.e unadorned %p) are
hashed to prevent leaking information about the kernel memory layout. This
has the added benefit of providing a unique identifier. On 64-bit machines
the first 32 bits are zeroed. The kernel will print ``(ptrval)`` until it
gathers enough entropy."

Instead of passing %pK, which can print the correct address, simply
remove the entire message as it is not really that useful.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:54 +02:00
Eugen Hristev
3e82f2f34c can: m_can: implement errata "Needless activation of MRAF irq"
During frame reception while the MCAN is in Error Passive state and the
Receive Error Counter has thevalue MCAN_ECR.REC = 127, it may happen
that MCAN_IR.MRAF is set although there was no Message RAM access
failure. If MCAN_IR.MRAF is enabled, an interrupt to the Host CPU is
generated.

Work around:
The Message RAM Access Failure interrupt routine needs to check whether

    MCAN_ECR.RP = '1' and MCAN_ECR.REC = '127'.

In this case, reset MCAN_IR.MRAF. No further action is required.
This affects versions older than 3.2.0

Errata explained on Sama5d2 SoC which includes this hardware block:
http://ww1.microchip.com/downloads/en/DeviceDoc/SAMA5D2-Family-Silicon-Errata-and-Data-Sheet-Clarification-DS80000803B.pdf
chapter 6.2

Reproducibility: If 2 devices with m_can are connected back to back,
configuring different bitrate on them will lead to interrupt storm on
the receiving side, with error "Message RAM access failure occurred".
Another way is to have a bad hardware connection. Bad wire connection
can lead to this issue as well.

This patch fixes the issue according to provided workaround.

Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:54 +02:00
Sean Nyekjaer
35b7fa4d07 can: mcp251x: add support for mcp25625
Fully compatible with mcp2515, the mcp25625 have integrated transceiver.

This patch adds support for the mcp25625 to the existing mcp251x driver.

Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:53 +02:00
Anssi Hannula
904044dd8f can: xilinx_can: use correct bittiming_const for CAN FD core
Commit 9e5f1b273e ("can: xilinx_can: add support for Xilinx CAN FD
core") added a new can_bittiming_const structure for CAN FD cores that
support larger values for tseg1, tseg2, and sjw than previous Xilinx CAN
cores, but the commit did not actually take that into use.

Fix that.

Tested with CAN FD core on a ZynqMP board.

Fixes: 9e5f1b273e ("can: xilinx_can: add support for Xilinx CAN FD core")
Reported-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:53 +02:00
Joakim Zhang
247e5356a7 can: flexcan: fix timeout when set small bitrate
Current we can meet timeout issue when setting a small bitrate like
10000 as follows on i.MX6UL EVK board (ipg clock = 66MHZ, per clock =
30MHZ):

| root@imx6ul7d:~# ip link set can0 up type can bitrate 10000

A link change request failed with some changes committed already.
Interface can0 may have been left with an inconsistent configuration,
please check.

| RTNETLINK answers: Connection timed out

It is caused by calling of flexcan_chip_unfreeze() timeout.

Originally the code is using usleep_range(10, 20) for unfreeze
operation, but the patch (8badd65 can: flexcan: avoid calling
usleep_range from interrupt context) changed it into udelay(10) which is
only a half delay of before, there're also some other delay changes.

After double to FLEXCAN_TIMEOUT_US to 100 can fix the issue.

Meanwhile, Rasmus Villemoes reported that even with a timeout of 100,
flexcan_probe() fails on the MPC8309, which requires a value of at least
140 to work reliably. 250 works for everyone.

Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:53 +02:00
Alexander Dahl
0ed89d777d can: usb: Kconfig: Remove duplicate menu entry
This seems to have slipped in by accident when sorting the entries.

Fixes: ffbdd9172e
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
2019-06-07 23:03:53 +02:00
Thomas Gleixner
4d8bc51069 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 412
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2 of the license this program
  is distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 2 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190112.858563475@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:14 +02:00
Thomas Gleixner
35e62ae830 treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 344
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the version 2 of the gnu general public
  license as published by the free software foundation this program is
  distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not see http www gnu org
  licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 15 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.427740574@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:07 +02:00
Thomas Gleixner
2b72c9e36c treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 340
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2 of the license this program
  is distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not see http www gnu org
  licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 15 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.052642892@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:37:07 +02:00
Thomas Gleixner
8e8e69d67e treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 285
Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation version 2 of the license this program
  is distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 100 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-06-05 17:36:37 +02:00
Thomas Gleixner
dd2878aace treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 198
Based on 1 normalized pattern(s):

  this software may be distributed under the terms of the gnu general
  public license gpl version 2 as distributed in the copying file from
  the main directory of the linux kernel source

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 1 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.816396794@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:29:22 -07:00