Add a newline to the end of drivers/spi-nor/Makefile to get rid the message,
"No newline at end of file", produced by git. This fix will allow subsequent
changes to the file to be able to produce clean patches.
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
The driver made the wrong assumption that the 4B setting was
autodetected for all chips of the AST2500 FMC flash controller. This
is only the case for the CS0.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
There is no need to include <linux/pinctrl/consumer.h> as no pinctrl
function is used in this driver, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
There is no need to include <linux/pinctrl/consumer.h> as no pinctrl
function is used in this driver, so just remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
S25FL{128|256|512}S datasheets say:
"When P_ERR or E_ERR bits are set to one, the WIP bit will remain set to
one indicating the device remains busy and unable to receive new operation
commands. A Clear Status Register (CLSR) command must be received to return
the device to standby mode."
Current spi-nor code works until first error occurs, but write/erase errors
are not just rare hardware failures, they also occur if user tries to flash
write-protected areas. After such attempt no SPI command can be executed
any more and even read fails. This patch adds support for P_ERR and E_ERR
bits in Status Register 1 (so that operation fails immediately and not
after a long timeout) and proper recovery from the error condition.
Tested on Spansion S25FS128S, which is supported by S25FL129P entry.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Intel Denverton exposes the SPI serial flash controller as a PCI device
instead of being part of the LPC chip as previous generations did.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@free-electrons.com>
This patch adds support to the JESD216 rev B standard and parses the SFDP
tables to dynamically initialize the 'struct spi_nor_flash_parameter'.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
The variable was already marked 'const' before the previous
patch, but the qualifier was in an unusual place, and now the
extra 'const' causes a harmless warning:
drivers/mtd/spi-nor/cadence-quadspi.c:1286:34: error: duplicate 'const' declaration specifier [-Werror=duplicate-decl-specifier]
This removes the other 'const' instead.
Fixes: f993c123b4 ("mtd: spi-nor: cqspi: make of_device_ids const")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
The segment registers of the SMC controller provide a way to configure
the mapping windows of the chips on the AHB bus. The settings are
required to be correct when the controller operates in Command mode,
which is the case for DMAs and the LPC mapping.
This tries to set the segment registers of each chip depending on the
size of the flash device and depending on the previous segment
settings, in order to have a contiguous window across multiple chips.
Unfortunately, the AST2500 SPI controller has a bug and it is not
possible to configure a full 128MB window for a chip of the same
size. The window size needs to be restricted to 120MB. This issue only
applies to CE0.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
There is no need to keep the dummy bytes in the control register if
the command mode is not kept also. This could lead to an inconsistent
setting : normal read mode (command 0x3) and dummy bytes. It is to be
noted that the HW allows such a configuration.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
These devices are used on OpenPOWER systems. The SPI_NOR_DUAL_READ
flags is added for the Aspeed SoCs which do not support QUAD reads.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
These modules are used on the OpenPOWER Witherspoon systems to hold
the POWER9 host firmware image. The SPI_NOR_DUAL_READ flags is added
for the Aspeed SoCs which do not support QUAD reads.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Similar to the other ones, different size. The "JV" suffix is in
the datasheet, I haven't seen mentions of a different one.
The datasheet indicates DUAL and QUAD are supported.
http://www.winbond.com/resource-files/w25m512jv%20revc%2001062017.pdf
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Before commit cff959958832 ("mtd: spi-nor: introduce SPI 1-2-2 and SPI
1-4-4 protocols") then we treated 1 as -EINVAL in the caller but after
that commit we changed to propagate the return. My static checker
complains that it's eventually passed to an ERR_PTR() and later
dereferenced, but I'm not totally certain if that's true. Regardless,
returning 1 is wrong.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
This patch fixes some compiler errors:
- change format strings to use %zx for size_t
- add missing #include <linux/sizes.h>
Cc: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
This patch starts adding support to Octo SPI protocols (SPI x-y-8).
Op codes for Fast Read and/or Page Program operations using Octo SPI
protocols are not known yet (no JEDEC specification has defined them yet)
but we'd rather introduce the Octo SPI protocols now so it's done as it
should be.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
This patch introduces support to Double Transfer Rate (DTR) SPI protocols.
DTR is used only for Fast Read operations.
According to manufacturer datasheets, whatever the number of I/O lines
used during instruction (x) and address/mode/dummy (y) clock cycles, DTR
is used only during data (z) clock cycles of SPI x-y-z protocols.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
This patch changes the prototype of spi_nor_scan(): its 3rd parameter
is replaced by a 'struct spi_nor_hwcaps' pointer, which tells the spi-nor
framework about the actual hardware capabilities supported by the SPI
controller and its driver.
Besides, this patch also introduces a new 'struct spi_nor_flash_parameter'
telling the spi-nor framework about the hardware capabilities supported by
the SPI flash memory and the associated settings required to use those
hardware caps.
Then, to improve the readability of spi_nor_scan(), the discovery of the
memory settings and the memory initialization are now split into two
dedicated functions.
1 - spi_nor_init_params()
The spi_nor_init_params() function is responsible for initializing the
'struct spi_nor_flash_parameter'. Currently this structure is filled with
legacy values but further patches will allow to override some parameter
values dynamically, for instance by reading the JESD216 Serial Flash
Discoverable Parameter (SFDP) tables from the SPI memory.
The spi_nor_init_params() function only deals with the hardware
capabilities of the SPI flash memory: especially it doesn't care about
the hardware capabilities supported by the SPI controller.
2 - spi_nor_setup()
The second function is called once the 'struct spi_nor_flash_parameter'
has been initialized by spi_nor_init_params().
With both 'struct spi_nor_flash_parameter' and 'struct spi_nor_hwcaps',
the new argument of spi_nor_scan(), spi_nor_setup() computes the best
match between hardware caps supported by both the (Q)SPI memory and
controller hence selecting the relevant settings for (Fast) Read and Page
Program operations.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
NAND, from Boris:
"""
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
SPI NOR, from Cyrille:
"""
- fixes in the hisi SPI controller driver.
- fixes in the intel SPI controller driver.
- fixes in the Mediatek SPI controller driver.
- fixes to some SPI flash memories not supported the Chip Erase command.
- add support to some new memory parts (Winbond, Macronix, Micron, ESMT).
- add new driver for the STM32 QSPI controller.
"""
And a few fixes for Gemini and Versatile platforms on physmap-of
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dxj5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
When nor's size larger than 16MByte, nor's address width maybe
set to 3 or 4, and controller should change address width according
to nor's setting.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The quadspi is a specialized communication interface targeting single,
dual or quad SPI Flash memories.
It can operate in any of the following modes:
-indirect mode: all the operations are performed using the quadspi
registers
-read memory-mapped mode: the external Flash memory is mapped to the
microcontroller address space and is seen by the system as if it was
an internal memory
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
All required stateless 4-byte op codes are supported by this flash
chip. The stateless 4-byte support can't be autodetected due to a
missing 4-byte Address Instruction Table in SFDP.
Fixes hangs on reboot for SoCs expecting the flash chip in 3byte mode.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Add new Micron N25Q256A (N25Q256A11) 256Mbit NOR Flash in the list
of supported devices. This chip has the same structure as the N25Q256A
but ID and voltage (1V8) to use is different. Therefore, this adds
N25Q256A11 as n25q256ax1.
In the future, for new Micron memories we could use the patterns
"n25q*ax1" for 1V8 and "n25q*ax3" for 3V3 memories.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.kw@hitachi.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Macronix MX25U2033E, MX25U4033E and MX25U4035 devices are used in 4/5/6th
generation Kindle ebook readers. Both MX25U403x variants share the same
JEDEC id. Add those spi-nor variants and the similar MX25U8035 mentioned
in the same set of datasheets.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Winbond W25Q20BW devices are used in 4/5th generation Kindle ebook readers.
Add this spi-nor device and the similar W25Q20 devices to the list of known
devices.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Micron n25q00 are stacked chips, thus do not support chip erase.
>From now spi-nor framework will not send chip erase command,
instead will use sector at time erase procedure.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Currently it is possible to disable chip erase for spi-nor driver.
Some modern stacked (multi die) flash chips do not support chip
erase opcode at all but spi-nor framework needs to cope with them too.
This commit extends existing functionality to allow disable
chip erase for a single flash chip.
Signed-off-by: Marcin Krzeminski <mar.krzeminski@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fix typos and add the following to the scripts/spelling.txt:
disble||disable
disbled||disabled
I kept the TSL2563_INT_DISBLED in /drivers/iio/light/tsl2563.c
untouched. The macro is not referenced at all, but this commit is
touching only comment blocks just in case.
Link: http://lkml.kernel.org/r/1481573103-11329-20-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the ESMT F25L32QA and F25L64QA.
These are 4MB and 8MB SPI-NOR Chips from Elite Semiconductor Memory
Technology.
Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This fixes a sparse warning about incorrect type in return expression.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
writeable in struct intel_spi is a boolean and assignment should be to
true/false not 1/0 as recommended by boolinit.cocci.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
-----BEGIN PGP SIGNATURE-----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=/fPM
-----END PGP SIGNATURE-----
Merge tag 'spi-nor/for-4.11-v2' of git://github.com/spi-nor/linux
From Cyrille:
"""
This pull request contains the following notable changes:
- add support to the 4-byte address instruction set.
- add support to new memory parts.
- add support to S3AN memories.
- add support to the Intel SPI controller.
- add support to the Aspeed AST2400 and AST2550 controllers.
- fix max SPI transfer and message sizes in m25p80_read().
- fix the Candence QSPI driver.
- fix the Freescale QSPI driver.
"""
Checking for ret < 0 is redundant because a previous check on ret
being non-zero already handles the ret < 0 case. Remove the redundant
code. Found by CoverityScan, CID#1398863, CID#1398864
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
There are some read modes for flash, such as NORMAL, FAST,
QUAD, DDR QUAD. These modes will use the identical lut table base
So rename SEQID_QUAD_READ to SEQID_READ.
Signed-off-by: Yunhui Cui <B56489@freescale.com>
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
We can get the read/write/erase opcode from the spi nor framework
directly. This patch uses the information stored in the SPI-NOR to
remove the hardcode in the fsl_qspi_init_lut().
Signed-off-by: Yunhui Cui <B56489@freescale.com>
Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Acked-by: Han xu <han.xu@nxp.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The page calculation under spi_nor_s3an_addr_convert() was wrong. On
Default Address Mode we need to perform a divide by page_size.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
The first argument of ioread32_rep() and ioread8_rep is not
const. Change aspeed_smc_read_from_ahb() prototype to fix compile
warning :
drivers/mtd/spi-nor/aspeed-smc.c: In function 'aspeed_smc_read_from_ahb':
drivers/mtd/spi-nor/aspeed-smc.c:212:16: warning: passing argument 1 of 'ioread32_rep' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
ioread32_rep(src, buf, len >> 2);
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
-----BEGIN PGP SIGNATURE-----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=1Yep
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-mtd-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
From Lee Jones:
"""
Immutable branch between MFD and MTD due for the v4.11 merge window
"""
This chip has write protection enabled on power-up,
so this flag is necessary to support write operations.
Signed-off-by: Victor Shyba <victor1984@riseup.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
This patch provides an alternative mean to support memory above 16MiB
(128Mib) by replacing 3byte address op codes by their associated 4byte
address versions.
Using the dedicated 4byte address op codes doesn't change the internal
state of the SPI NOR memory as opposed to using other means such as
updating a Base Address Register (BAR) and sending command to enter/leave
the 4byte mode.
Hence when a CPU reset occurs, early bootloaders don't need to be aware
of BAR value or 4byte mode being enabled: they can still access the first
16MiB of the SPI NOR memory using the regular 3byte address op codes.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Tested-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This patch renames the SPINOR_OP_* macros of the 4-byte address
instruction set so the new names all share a common pattern: the 4-byte
address name is built from the 3-byte address name appending the "_4B"
suffix.
The patch also introduces new op codes to support other SPI protocols such
as SPI 1-4-4 and SPI 1-2-2.
This is a transitional patch and will help a later patch of spi-nor.c
to automate the translation from the 3-byte address op codes into their
4-byte address version.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This driver adds mtd support for the Aspeed AST2400 SoC static memory
controllers:
* New Static Memory Controller (referred as FMC)
. BMC firmware
. AST2500 compatible register set
. 5 chip select pins (CE0 ∼ CE4)
. supports NOR flash, NAND flash and SPI flash memory.
* SPI Flash Controller (SPI)
. host Firmware
. slightly different register set, between AST2500 and the legacy
controller
. supports SPI flash memory
. 1 chip select pin (CE0)
The legacy static memory controller (referred as SMC) is not
supported, as well as types other than SPI.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
