Previously, we wanted SCSI devices corrsponding to ATA devices to
be runtime resumed when the power resource for those ATA device was
turned on by some other device, so we added the SCSI device to the
dependent device list of the ATA device's ACPI node. However, this
code has no effect after commit 41863fc (ACPI / power: Drop automaitc
resume of power resource dependent devices) and the mechanism it was
supposed to implement is regarded as a bad idea now, so drop it.
[rjw: Changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull libata changes from Tejun Heo:
"Two interesting changes.
- libata acpi handling has been restructured so that the association
between ata devices and ACPI handles are less convoluted. This
change shouldn't change visible behavior.
- Queued TRIM support, which enables sending TRIM to the device
without draining in-flight RW commands, is added. Currently only
enabled for ahci (and likely to stay that way for the foreseeable
future).
Other changes are driver-specific updates / fixes"
* 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: bugfix: Remove __le32 in ata_tf_to_fis()
libata: acpi: Remove ata_dev_acpi_handle stub in libata.h
libata: Add support for queued DSM TRIM
libata: Add support for SEND/RECEIVE FPDMA QUEUED
libata: Add H2D FIS "auxiliary" port flag
libata: Populate host-to-device FIS "auxiliary" field
ata: acpi: rework the ata acpi bind support
sata, highbank: send extra clock cycles in SGPIO patterns
sata, highbank: set tx_atten override bits
devicetree: create a separate binding description for sata_highbank
drivers/ata/sata_rcar.c: simplify use of devm_ioremap_resource
sata highbank: enable 64-bit DMA mask when using LPAE
ata: pata_samsung_cf: add missing __iomem annotation
ata: pata_arasan: Staticize local symbols
sata_mv: Remove unneeded CONFIG_HAVE_CLK ifdefs
ata: use dev_get_platdata()
sata_mv: Remove unneeded forward declaration
libata: acpi: remove dead code for ata_acpi_(un)bind
libata: move 'struct ata_taskfile' and friends from ata.h to libata.h
Binding ACPI handle to SCSI device has several drawbacks, namely:
1 During ATA device initialization time, ACPI handle will be needed
while SCSI devices are not created yet. So each time ACPI handle is
needed, instead of retrieving the handle by ACPI_HANDLE macro,
a namespace scan is performed to find the handle for the corresponding
ATA device. This is inefficient, and also expose a restriction on
calling path not holding any lock.
2 The binding to SCSI device tree makes code complex, while at the same
time doesn't bring us any benefit. All ACPI handlings are still done
in ATA module, not in SCSI.
Rework the ATA ACPI binding code to bind ACPI handle to ATA transport
devices(ATA port and ATA device). The binding needs to be done only once,
since the ATA transport devices do not go away with hotplug. And due to
this, the flush_work call in hotplug handler for ATA bay is no longer
needed.
Tested on an Intel test platform for binding and runtime power off for
ODD(ZPODD) and hard disk; on an ASUS S400C for binding and normal boot
and S3, where its SATA port node has _SDD and _GTF control methods when
configured as an AHCI controller and its PATA device node has _GTF
control method when configured as an IDE controller. SATA PMP binding
and ATA hotplug is not tested.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
There are several places in the tree where ACPI_STATE_D3 is used
instead of ACPI_STATE_D3_COLD which should be used instead for
clarity. Modify them all to use ACPI_STATE_D3_COLD as appropriate.
[The definition of ACPI_STATE_D3 itself cannot go away at this point
as it is part of ACPICA.]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Commit 30dcf76acc "libata: migrate ACPI code over to new bindings"
mistakenly dropped the code to register hotplug notificaion handler
for ATA port/devices, causing regression for people using ATA bay,
as kernel bug #59871 shows.
Fix this by adding back the hotplug notification handler registration
code. Since this code has to be run once and notification needs to
be installed on every ATA port/devices handle no matter if there is
actual device attached, we can't do this in binding time for ATA
device ACPI handle, as the binding only occurs when a SCSI device is
created, i.e. there is device attached. So introduce the
ata_acpi_hotplug_init() function to loop scan all ATA ACPI handles
and if it is available, install the notificaion handler for it during
ATA init time.
With the ATA ACPI handle binding to SCSI device tree, it is possible
now that when the SCSI hotplug work removes the SCSI device, the ACPI
unbind function will find that the corresponding ACPI device has
already been deleted by dock driver, causing a scaring message like:
[ 128.263966] scsi 4:0:0:0: Oops, 'acpi_handle' corrupt
Fix this by waiting for SCSI hotplug task finish in our notificaion
handler, so that the removal of ACPI device done in ACPI unbind
function triggered by the removal of SCSI device is run earlier when
ACPI device is still available.
[rjw: Rebased]
References: https://bugzilla.kernel.org/show_bug.cgi?id=59871
Reported-bisected-and-tested-by: Dirk Griesbach <spamthis@freenet.de>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Cc: 3.6+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch restores libata.noacpi support to libata-acpi.c.
There are broken optional control methods for ATA controller devices in the
real world. The libata.noacpi has been used for a long time as a
workaround to deal with issues caused by the broken ASL codes.
1. The "noacpi" option is introduced by the following commit:
commit 11ef697b37
Date: Thu, 28 Sep 2006 11:29:01 -0700
Subject: libata: ACPI and _GTF support
2. The "noacpi" option is renamed to "libata_noacpi" by the following
commit:
commit d7d0dad62a
Date: Wed, 28 Mar 2007 01:57:37 -0400
Subject: [libata] Disable ACPI by default; fix namespace problems
3. Some of its logics are changed over time - becomes relying on the
"acpi_handle" bound to the ATA devices since this commit:
commit fafbae87db
Date: Tue, 15 May 2007 03:28:16 +0900
Subject: libata-acpi: implement ata_acpi_associate()
4. The option is deleted by the following commit:
commit 30dcf76acc
Date: Mon, 25 Jun 2012 16:13:04 +0800
Subject: libata: migrate ACPI code over to new bindings
But the libata.noacpi setup is still left in the kernel without codes to
implement it. So the deletion introduces a regression to the Linux.
This patch disables ATA_ACPI support at runtime by stopping acpi binding
on the ATA devices to fix this regression.
This patch is tested by booting a SATA x86-64 kernel or a PATA x86 kernel
with or without "libata.noacpi=1" kernel command line argument.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since commit 30dcf76acc, ata_ap_acpi_handle will always do a namespace
walk, which requires acquiring an acpi namespace mutex. This made it
impossible to be used when calling path has held a spinlock.
For example, it can occur in the following code path for pata_acpi:
ata_scsi_queuecmd (ap->lock is acquired)
__ata_scsi_queuecmd
ata_scsi_translate
ata_qc_issue
pacpi_qc_issue
ata_acpi_stm
ata_ap_acpi_handle
acpi_get_child
acpi_walk_namespace
acpi_ut_acquire_mutex (acquire mutex while holding lock)
This caused scheduling while atomic bug, as reported in bug #56781.
Actually, ata_ap_acpi_handle doesn't have to walk the namespace every
time it is called, it can simply return the bound acpi handle on the
corresponding SCSI host. The reason previously it is not done this way
is, ata_ap_acpi_handle is used in the binding function
ata_acpi_bind_host by ata_acpi_gtm when the handle is not bound to the
SCSI host yet. Since we already have the ATA port's handle in its
binding function, we can simply use it instead of calling
ata_ap_acpi_handle there. So introduce a new function __ata_acpi_gtm,
where it will receive an acpi handle param in addition to the ATA port
which is solely used for debug statement. With this change, we can make
ata_ap_acpi_handle simply return the bound handle for SCSI host instead
of walking the acpi namespace now.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=56781
Reported-and-tested-by: <kenzopl@o2.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
With commit:
bc9b6407bd
ACPI / PM: Rework the handling of devices depending on power resources
The ACPI core now takes care of the power resources an acpi device
depends on in that when the power resources are turned on, any devices
that are bound to or in the dependent list of this acpi device will be
runtime resumed. So there is no need for ata acpi code to duplicate this
effort, and thus, the ata_acpi_(un)register_power_resource functions are
no longer needed.
The above commit thinks the scsi device is not bound to the acpi device,
so needs to be added to the dependent list. But actually, it is. So
there is no need to add it to the dependent list, or it will be runtime
resumed twice(though this wouldn't cause any problem).
This patch fixes it, and as a result, the
ata_acpi_(un)register_power_resource and ata_acpi_(un)bind functions
are removed.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix a copy and paste mistake introduced in:
commit bc9b6407bd
"ACPI / PM: Rework the handling of devices depending on power resources"
Signed-off-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After PCI and USB have stopped using the .find_bridge() callback in
struct acpi_bus_type, the only remaining user of it is SATA, but SATA
only pretends to be a user, because it points that callback to a stub
always returning -ENODEV.
For this reason, drop the SATA's dummy .find_bridge() callback and
remove .find_bridge(), which is not used any more, from struct
acpi_bus_type entirely.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
USB uses the .find_bridge() callback from struct acpi_bus_type
incorrectly, because as a result of the way it is used by USB every
device in the system that doesn't have a bus type or parent is
passed to usb_acpi_find_device() for inspection.
What USB actually needs, though, is to call usb_acpi_find_device()
for USB ports that don't have a bus type defined, but have
usb_port_device_type as their device type, as well as for USB
devices.
To fix that replace the struct bus_type pointer in struct
acpi_bus_type used for matching devices to specific subsystems
with a .match() callback to be used for this purpose and update
the users of struct acpi_bus_type, including USB, accordingly.
Define the .match() callback routine for USB, usb_acpi_bus_match(),
in such a way that it will cover both USB devices and USB ports
and remove the now redundant .find_bridge() callback pointer from
usb_acpi_bus.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Discussion was continuing after patch application, trying to figure out how
to best mesh exported data with the installers, boot-time agents and other
parties that want this info.
2) Merge Zero-Power Optical Device Driver (ZPODD) support, bringing
the wonderfulness of sane power management to your CD/DVD device.
Includes one SCSI-subsystem patch (with appropriate ACKs),
adding runtime PM support to 'sr' driver. That is the ZPODD interaction
bits.
Patchset went through some 13 revisions before it got here; kudos to
Intel for persistence.
3) pata_samsung_cf: use devm_clk_get()
4) more ata_piix, ahci PCI IDs
5) Add SATA driver for R-Car SoC
6) Convert libata to use devm_ioremap_resource (Note: I think
Greg sent this to you, also)
7) Set proper Sense Key (SK) in the SCSI simulator when
ATA passthrough indicates check condition. Google and specification
hawks everywhere shall rejoice.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=YvYo
-----END PGP SIGNATURE-----
Merge tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata updates from Jeff Garzik:
1) apply, and then revert, the sysfs export of ATA host controller
number. Discussion was continuing after patch application, trying to
figure out how to best mesh exported data with the installers,
boot-time agents and other parties that want this info.
2) Merge Zero-Power Optical Device Driver (ZPODD) support, bringing the
wonderfulness of sane power management to your CD/DVD device.
Includes one SCSI-subsystem patch (with appropriate ACKs), adding
runtime PM support to 'sr' driver. That is the ZPODD interaction
bits.
Patchset went through some 13 revisions before it got here; kudos to
Intel for persistence.
3) pata_samsung_cf: use devm_clk_get()
4) more ata_piix, ahci PCI IDs
5) Add SATA driver for R-Car SoC
6) Convert libata to use devm_ioremap_resource (Note: I think Greg sent
this to you, also)
7) Set proper Sense Key (SK) in the SCSI simulator when ATA passthrough
indicates check condition. Google and specification hawks everywhere
shall rejoice.
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (22 commits)
[libata] fix smatch warning for zpodd_wake_dev
[libata] Set proper SK when CK_COND is set.
[libata] Convert to devm_ioremap_resource()
libata: add R-Car SATA driver
ahci: Add Device IDs for Intel Wellsburg PCH
ata_piix: Add Device IDs for Intel Wellsburg PCH
[SCSI] remove can_power_off flag from scsi_device
[libata] scsi: no poll when ODD is powered off
[SCSI] sr: support runtime pm
ahci: AHCI-mode SATA patch for Intel Avoton DeviceIDs
ata_piix: IDE-mode SATA patch for Intel Avoton DeviceIDs
[libata] PM code cleanup for ata port
[libata] pm: differentiate system and runtime pm for ata port
Revert "libata: export host controller number thru /sys"
libata: do not suspend port if normal ODD is attached
libata: expose pm qos flags for ata device
libata: handle power transition of ODD
libata: check zero power ready status for ZPODD
libata: move acpi notification code to zpodd
libata: identify and init ZPODD devices
...
We need to do different things for system PM and runtime PM, e.g. we do
not need to enable runtime wake for ZPODD when we are doing system
suspend, etc.
Currently, we use PMSG_SUSPEND for both system suspend and runtime
suspend and PMSG_ON for both system resume and runtime resume. Change
this by using PMSG_AUTO_SUSPEND for runtime suspend and PMSG_AUTO_RESUME
for runtime resume. And since PMSG_ON means no transition, it is changed
to PMSG_RESUME for ata port's system resume.
The ata_acpi_set_state is modified accordingly, and the sata case and
pata case is seperated for easy reading.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Expose pm qos flags to user space so that user has a chance to disable
ZPODD feature, if he/she has a broken platform or devices or simply does
not like this feature.
This flag is exposed to user space only for ZPODD devices.
Due to this flag, it is possible the ODD is ZP ready but we didn't power
it off. So the zp_ready flag will need to be cleared whenever we found
the ODD is not in ZP ready state. Previously, once zp_ready is set, the
ODD will always be powered off and the flag will be cleared in
post_poweron. But this is no longer the case now.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
When ata port is runtime suspended, it will check if the ODD attched to
it is a zero power(ZP) capable ODD and if the ZP capable ODD is in zero
power ready state. And if this is not the case, the highest acpi state
will be limited to ACPI_STATE_D3_HOT to avoid powering off the ODD. And
if the ODD can be powered off, runtime wake capability needs to be
enabled and powered_off flag will be set to let resume code knows that
the ODD was in powered off state.
And on resume, before it is powered on, if it was powered off during
suspend, runtime wake capability needs to be disabled. After it is
recovered, the ODD is considered functional, post power on processing
like eject tray if the ODD is drawer type is done, and several ZPODD
related fields will also be reset.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since the ata acpi notification code introduced in commit
3bd46600a7 is solely for ZPODD, and we
now have a dedicated place for it, move these code there.
And the ata_acpi_add_pm_notifier code is changed a little bit in that it
is now invoked when scsi device is not bound with ACPI yet, so the way
to get the acpi handle is different with the previous version. And the
ata_acpi_add/remove_pm_notifier is also simplified a little bit in that
it doesn't check if the acpi_device for the handle exists or not as the
odd_can_poweroff function already checked that.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 0090def6 (ACPI: Add interface to register/unregister device
to/from power resources) made it possible to indicate to the ACPI
core that if the given device depends on any power resources, then
it should be resumed as soon as all of the power resources required
by it to transition to the D0 power state have been turned on.
Unfortunately, however, this was a mistake, because all devices
depending on power resources should be treated this way (i.e. they
should be resumed when all power resources required by their D0
state have been turned on) and for the majority of those devices
the ACPI core can figure out by itself which (physical) devices
depend on what power resources.
For this reason, replace the code added by commit 0090def6 with a
new, much more straightforward, mechanism that will be used
internally by the ACPI core and remove all references to that code
from kernel subsystems using ACPI.
For the cases when there are (physical) devices that should be
resumed whenever a not directly related ACPI device node goes into
D0 as a result of power resources configuration changes, like in
the SATA case, add two new routines, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), allowing subsystems to manage
such dependencies. Convert the SATA subsystem to use the new
functions accordingly.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 66fa7f215 "libata-acpi: improve ACPI disabling" introdcued the
behaviour of disabling ATA ACPI if ata_acpi_on_devcfg failed the 2nd
time, but commit 30dcf76ac dropped this behaviour and this caused
problem for Dimitris Damigos, where his laptop can not resume correctly.
The bugzilla page for it is:
https://bugzilla.kernel.org/show_bug.cgi?id=49331
The problem is, ata_dev_push_id will fail the 2nd time it is invoked,
and due to disabling ACPI code is dropped, ata_acpi_on_devcfg which
calls ata_dev_push_id will keep failing and eventually made the device
disabled.
This patch restores the original behaviour, if acpi failed the 2nd time,
disable acpi functionality for the device(and we do not event need to
add a debug message for this as it is still there ;-).
Reported-by: Dimitris Damigos <damigos@freemail.gr>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
commit 6b66d95895 didn't handle SATA PMP
case in ata_acpi_bind_device and will cause a NULL ptr dereference when
user attached a SATA drive to the PMP port. Fix this by checking PMP
support.
This bug is reported by Dan van der Ster in the following bugzilla page:
https://bugzilla.kernel.org/show_bug.cgi?id=48211
Reported-by: Dan van der Ster <dan@vanderster.com>
Tested-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Tested-by: Simon <tangouniform@sbcglobal.net>
Commit 30dcf76acc mistakenly dropped
the code to get an initial gtm for the IDE channel. This caused the
following problem for Sergei:
http://marc.info/?l=linux-kernel&m=134484963618457&w=2
Fix this by adding the call back in ata_acpi_bind_host, and due to
this, the ata_ap_acpi_handle is modified accordingly.
Tested-by: Sergei Trofimovich <slyich@gmail.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
After merging the libata tree, today's [2012-07-01] linux-next build (x86_64
allmodconfig) failed like this:
drivers/ata/libata-acpi.c: In function 'ata_acpi_set_state':
drivers/ata/libata-acpi.c:872:5: error: too few arguments to function 'acpi_pm_device_sleep_state'
include/acpi/acpi_bus.h:418:5: note: declared here
Caused by commit 3bd46600a7 ("libata-acpi: add ata port runtime D3Cold
support") from the libata tree interacting with commit ee85f54371
("ACPI/PM: specify lowest allowed state for device sleep state") from the
pci tree.
This patch adds ACPI_STATE_D3 as the new third parameter to
acpi_pm_device_sleep_state()
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
If ATA device supports "Device Attention", then tell scsi layer that
the device supports runtime power off.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA port may support runtime D3Cold state, for example, Zero-power ODD case.
This patch adds wakeup notifier and enable/disable run_wake during
supend/resume.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, ata_acpi_set_state() only sets acpi sate for IDE port.
Remove this limitation.
Acked-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that we have the ability to directly glue the ACPI namespace to the
driver model in libata, we don't need the custom code to handle the same
thing. Remove it and migrate the functions over to the new code.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Holger Macht <holger@homac.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Associate the ACPI device tree and libata devices.
This patch uses the generic ACPI glue framework to do so.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Holger Macht <holger@homac.de>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (28 commits)
ACPI: delete stale reference in kernel-parameters.txt
ACPI: add missing _OSI strings
ACPI: remove NID_INVAL
thermal: make THERMAL_HWMON implementation fully internal
thermal: split hwmon lookup to a separate function
thermal: hide CONFIG_THERMAL_HWMON
ACPI print OSI(Linux) warning only once
ACPI: DMI workaround for Asus A8N-SLI Premium and Asus A8N-SLI DELUX
ACPI / Battery: propagate sysfs error in acpi_battery_add()
ACPI / Battery: avoid acpi_battery_add() use-after-free
ACPI: introduce "acpi_rsdp=" parameter for kdump
ACPI: constify ops structs
ACPI: fix CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS
ACPI: fix 80 char overflow
ACPI / Battery: Resolve the race condition in the sysfs_remove_battery()
ACPI / Battery: Add the check before refresh sysfs in the battery_notify()
ACPI / Battery: Add the hibernation process in the battery_notify()
ACPI / Battery: Rename acpi_battery_quirks2 with acpi_battery_quirks
ACPI / Battery: Change 16-bit signed negative battery current into correct value
ACPI / Battery: Add the power unit macro
...
Structs battery_file, acpi_dock_ops, file_operations,
thermal_cooling_device_ops, thermal_zone_device_ops, kernel_param_ops
are not changed in runtime. It is safe to make them const.
register_hotplug_dock_device() was altered to take const "ops" argument
to respect acpi_dock_ops' const notion.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 0d5ff56677 (libata: convert to iomap)
removed all checks of ATA_FLAG_MMIO but neglected to remove the flag itself.
Do it now, at last...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some minor improvements in error handling, but overall it was mostly dead
code.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
acpi_integer is now obsolete and removed from the ACPICA code base,
replaced by u64.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Missing _SDD is not an error. Don't treat it as one.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add ->gtf_filter to ata_device and set it to ata_acpi_gtf_filter when
initializing ata_link. This is to allow quirks which apply different
gtf filters.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently libata-acpi can only filter DIPM among SATA feature enables
via _GTF. This patch adds the capability to filter out FPDMA non-zero
offset, in-order guarantee and auto-activation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We're about to add more SATA_* and ATA_ACPI_FILTER_* constants.
Reformat them in preparation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch improve libata's output for error/notification messages
to allow easier comprehension and debugging:
When ATAPI commands issued through the SCSI layer fail, use SCSI
functions to print the CDB in human-readable form instead of just
dumping out the CDB in hex.
Print out the name of the failed command (as defined by the ATA
specification) in error handling output along with the raw register
contents.
When reporting status of ACPI taskfile commands executed on resume,
also output the names of the commands being executed (or not) in
readable form.
Since the extra data for printing command names increases kernel
size slightly, a config option has been added to allow disabling
command name output (as well as some of the error register parsing)
for those highly sensitive to kernel text size.
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
External driver files should not include any private acpica headers.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
There currently are the following looping constructs.
* __ata_port_for_each_link() for all available links
* ata_port_for_each_link() for edge links
* ata_link_for_each_dev() for all devices
* ata_link_for_each_dev_reverse() for all devices in reverse order
Now there's a need for looping construct which is similar to
__ata_port_for_each_link() but iterates over PMP links before the host
link. Instead of adding another one with long name, do the following
cleanup.
* Implement and export ata_link_next() and ata_dev_next() which take
@mode parameter and can be used to build custom loop.
* Implement ata_for_each_link() and ata_for_each_dev() which take
looping mode explicitly.
The following iteration modes are implemented.
* ATA_LITER_EDGE : loop over edge links
* ATA_LITER_HOST_FIRST : loop over all links, host link first
* ATA_LITER_PMP_FIRST : loop over all links, PMP links first
* ATA_DITER_ENABLED : loop over enabled devices
* ATA_DITER_ENABLED_REVERSE : loop over enabled devices in reverse order
* ATA_DITER_ALL : loop over all devices
* ATA_DITER_ALL_REVERSE : loop over all devices in reverse order
This change removes exlicit device enabledness checks from many loops
and makes it clear which ones are iterated over in which direction.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dock's uevent reported itself, not ata. It might be difficult to find an
ata device just according to a dock. This patch introduces docking ops
for each device in a dock. when docking, dock driver can send device
specific uevent. This should help dock station too (not just bay)
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
dock driver can handle ata(bay) hotplug now. dock driver already handles
_EJ0 and _STA, so remove them. Also libata doesn't need register
notification handler anymore.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The problem is introduced by commit
664d080c41.
acpi_evaluate_integer is a sleeping function,
and it should not be called with spin_lock_irqsave.
https://bugzilla.redhat.com/show_bug.cgi?id=451399
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some BIOSen enable DIPM via _GTF which causes command timeouts under
certain configuration. This didn't occur on 2.6.25 because 2.6.25
defaulted to SRST, so _GTF wasn't executed during boot probe, so ahci
host reset disabled DIPM and as _GTF wasn't executed after SRST, DIPM
wasn't enabled. On 2.6.26, hardreset is used during probe and after
probe _GTF is executed enabling DIPM and thus the failures.
This patch could theoretically disable DIPM on machines which used to
have it enabled on 2.6.25 but AFAIK ahci is currently the only driver
which uses SATA ACPI hierarchy (_SDD) and as the host reset would have
always disabled DIPM, this shouldn't happen.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* Differentiate between bay devices in dock stations and others:
- When an ACPI_NOTIFY_EJECT_REQUEST appears, just signal uevent to
userspace (that is when the optional eject button on a bay device is
pressed/pulled) giving the possibility to unmount file systems and to
clean up. Also, only send uevent in case we get an EJECT_REQUEST
without doing anything else. In other cases, you'll get an add/remove
event because libata attaches/detaches the device.
- In case of a dock event, which in turn signals an
ACPI_NOTIFY_EJECT_REQUEST, immediately detach the device, because it
may already have been gone
* In case of an ACPI_NOTIFY_DEVICE/BUS_CHECK, evaluate _STA to check if
the device has been plugged or unplugged. If plugged, hotplug it, if
unplugged, just signal event to userspace
(initial patch by Matthew Garrett <mjg59@srcf.ucam.org>)
* Call ACPI _EJ0 for detached devices
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
