Adds the needed code to be able to use 96KHz playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds the analog loopback/bypass support for twl4030 codec.
Details for the implementation:
It seams that the analog loopback needs the DAC powered on on the channel,
where the loopback is selected. The switch for the DACs has been moved from
the DAPM_DAC to the "Analog XX Playback Mixer". In this way the DAC will be
powered while the audio playback is used or/and the loopback is enabled for
the channel.
The twl4030 codec powering has been reworked. Now the codec will be powered as
long as it does not receives the SND_SOC_BIAS_OFF event. The exceptions are
when the given change in the registers needs the codec power down/up cycle in
order to take effect. Otherwise the codec is on.
When the codec enters to STANDBY state and none of the loopback paths are
enabled, than the amplifiers, which are no in the DAPM path are forced to turn
off and the PLL is disabled. When playback/capture starts the disabled gains
are restored and the PLL is enabled.
When one of the loopback enabled in STANDBY mode, the disabled gains are
restored and the PLL is enabled also.
In short: the codec always goes to the lowest power state based on the
bias_level and the bypass_state.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds DAPM implementaion for the capture path
on twlx030.
TWL has two physical ADC and two digital microphone (stereo) connections.
The CPU interface has four microphone channels.
For simplicity the microphone channel paths are named as:
TX1 (Left/Right) - when using i2s mode, only the TX1 data is valid
TX2 (Left/Right)
Input routing (simplified version):
There is two levels of mux settings for TWL in input path:
Analog input mux:
ADCL <- {Off, Main mic, Headset mic, AUXL, Carkit mic}
ADCR <- {Off, Sub mic, AUXR}
Analog/Digital mux:
TX1 Analog mode:
TX1L <- ADCL
TX1R <- ADCR
TX1 Digital mode:
TX1L <- Digimic0 (Left)
TX1R <- Digimic0 (Right)
TX2 Analog mode:
TX2L <- ADCL
TX2R <- ADCR
TX2 Digital mode:
TX2L <- Digimic1 (Left)
TX2R <- Digimic1 (Right)
The patch provides the following user controls for the capture path:
Mux settings:
"TX1 Capture Route": {Analog, Digimic0}
"TX2 Capture Route": {Analog, Digimic1}
"Analog Left Capture Route": {Off, Main Mic, Headset Mic, AUXL, Carkit Mic}
"Analog Right Capture Route": {Off, Sub Mic, AUXR}
Volume/Gain controls:
"TX1 Digital Capture Volume": Stereo gain control for TX1 path
"TX2 Digital Capture Volume": Stereo gain control for TX2 path
"Analog Capture Volume": Stereo gain control for the analog path only
Important things for the board files:
Microphone bias:
"Mic Bias 1": Bias for Main mic or for digimic0 (analog or digital path)
"Mic Bias 2": Bias for Sub mic or for digimic1 (analog or digital path)
"Headset Mic Bias": Bias for Headset mic
When the routing configured correctly only the needed components will be
powered/enabled.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A special start-up sequence is required to reduce the pop-noise of Class D
amplifier when enable hands-free on TWL4030.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The TWL4030 codec device has two ADCs. Both of them can have
several inputs routed to them, but TRM says that only one source
can be selected for every ADC, even though every source has a
dedicated bit in the registers.
This patch adds input source controls. It modifies default register
values to have no inputs selected and ADCs disabled. When some
input is selected, control handlers enable apropriate input
amplifier and ADC. If a microphone is selected, bias power is
automatically enabled. When some input is deselected, unused
chip parts are disabled.
Microphone and line input recording tested on OMAP3 pandora board.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
