Move them to radeon_asic.h together with the other asic
specific stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The vbios only partially initializes the memory controller on
NI, so now we need to load the MC ucode in the driver and set
the default clocks once the ucode is loaded.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The MC ucode is no longer loaded by the vbios
tables as on previous asics. It now must be loaded
by the driver.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The hardware supports advanced user defined color management
but at the moment, there is no infrastructure in place to take
advantage of it so for now we just support the legacy LUTs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds some new NI (northern islands) specific display
register defines.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
NI chips no longer load the MC ucode in the asic_init sequence so
the asic comes up in a basic mode with low engine/memory clocks and
a voltage. Once the MC ucode is loaded by the driver the card
can be programmed to it's proper default clocks and voltage. As such
the default clocks in the firmware info table as the post clocks, not
the default running clocks. Track the default post clocks and default
running clocks separately to handle this.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some systems disable the vbios on secondary cards or cards that
have been posted. This code re-enabled the vbios so the driver
can load it.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Needed to tell which DIG encoders are HBR2 capable for DP 1.2.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DVOOutputControl table was removed for DCE5.
DVOEncoderControl now handles everything.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The DAC1OutputControl table was removed for DCE5.
DAC1EncoderControl now handles everything.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Supported on rv6xx/r7xx/evergreen. Cards come up in gen1 mode.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With cmwq, there's no reason for radeon to use a dedicated workqueue.
Drop dev_priv->wq and use system_wq instead.
Because radeon_driver_irq_uninstall_kms() may be called from
unsleepable context, the work items can't be flushed from there.
Instead, init and flush from radeon_irq_kms_init/fini().
While at it, simplify canceling/flushing of rdev->pm.dynpm_idle_work.
Always initialize and sync cancel instead of being unnecessarily smart
about it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The CMASK RAM is for colorbuffer compression (used in conjunction
with MSAA). Only one user (filp) can access it.
The CMASK RAM access is managed in the same way as Hyper-Z, but there is
a separate ioctl, because an app that uses MSAA does not necessarily
have to use zbuffering.
Signed-off-by: Marek Olšák <maraeo@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Acer laptop (TravelMate 5730G) has an HDMI connector
on the laptop and a DVI connector on the docking station
and both share the same encoder, hpd pin, and ddc line.
The bios connector table reflects this and is technically
correct, however, we drop the DVI connector here since
xrandr has no concept of encoders (only crtcs and connectors)
and will try and drive both connectors with different crtcs
which isn't possible on the hardware side and leaves no crtcs
for LVDS or VGA.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=32732
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
stage 1: turn card on, switch boot vga pointer.
stage 2: switch fbs, switch mux and power off old card.
Signed-off-by: Dave Airlie <airlied@redhat.com>
We need to track the state of the switch in drivers, so that after s/r
we don't resume the card we've explicitly switched off before. Also
don't allow a userspace open to occur if we've switched the gpu off.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This improves the IGD/DIS picking using firstly if Intel, then
if the bus is bus 0. There may be a correct way to do this, but
I've no idea what it is.
Signed-off-by: Dave Airlie <airlied@redhat.com>
At least on the nvidia mux the power switch seems to be executed
by the ACPI PS0/PS3 methods so need to do it explicitly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
As we have already detected something attached to the chip during
initialisation, always report the LVDS connector status as connected
during probing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The IPS driver is designed to be able to run detached from i915 and
just not enable GPU turbo in that case, in order to avoid module
dependencies between the two drivers. This means that we don't know
what the load order between the two is going to be, and we had
previously only supported IPS after (optionally) i915, but not i915
after IPS. If the wrong order was chosen, you'd get no GPU turbo, and
something like half the possible graphics performance.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
It's required by the specs, but we don't know why. Let's not find out
why.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
