Add support for sama7g5 pinctrl block, which has 5 PIO banks.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200917131257.273882-2-eugen.hristev@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1.Add I2S pins support for the JZ4780 SoC.
2.Add I2S pins support for the X1000 SoC.
3.Add I2S pins support for the X1500 SoC.
4.Add I2S pins support for the X1830 SoC.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200913065836.12156-4-zhouyanjie@wanyeetech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct the pullup and pulldown parameters of JZ4780 to make them
consistent with the parameters on the datasheet.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200913065836.12156-3-zhouyanjie@wanyeetech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add SSI pins support for the JZ4770 SoC and the
JZ4780 SoC from Ingenic.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200913065836.12156-2-zhouyanjie@wanyeetech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These were skipped in the original patches adding pinconf support for
the AST2600.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Link: https://lore.kernel.org/r/20200910025631.2996342-4-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Aspeed pinconf data structures are split into 'conf' and 'map'
types, where the 'conf' struct defines which register and bitfield to
manipulate, while the 'map' struct defines what value to write to
the register and bitfield.
Both structs have a mask member, and the wrong mask was being used to
tell the regmap which bits to update.
A todo is to look at whether we can remove the mask from the 'map'
struct.
Fixes: 5f52c85384 ("pinctrl: aspeed: Use masks to describe pinconf bitfields")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Link: https://lore.kernel.org/r/20200910025631.2996342-3-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When displaying which pinconf register and field is being touched,
format the field mask so that it's consistent with the way the pinmux
portion formats the mask.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200910025631.2996342-2-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change PINCTRL_IMX to tristate to support loadable module build.
And i.MX common pinctrl driver should depend on CONFIG_OF to make sure
no build error when i.MX common pinctrl driver is enabled for different
architectures without CONFIG_OF.
Also add module author, description and license.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/1599552721-24872-3-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use function callbacks for SCU related functions in pinctrl-imx.c
in order to support the scenario of PINCTRL_IMX is built in while
PINCTRL_IMX_SCU is built as module, all drivers using SCU pinctrl
driver need to initialize the SCU related function callback, and
no need to check CONFIG_PINCTRL_IMX_SCU anymore, hence stub functions
also can be removed.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/1599552721-24872-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Add last part of cleanup Cherryview driver to align with other drivers
* Due to above clean up Cherryview and Baytrail drivers to use common API
The following is an automated git shortlog grouped by driver:
baytrail:
- Switch to use intel_pinctrl_get_soc_data()
cherryview:
- Preserve CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs
- Switch to use intel_pinctrl_get_soc_data()
- Utilize temporary variable to hold device pointer
- Switch to use struct intel_pinctrl
- Move custom community members to separate data struct
- Drop stale comment
intel:
- Update header block to reflect direct dependencies
- Extract intel_pinctrl_get_soc_data() helper for wider use
-----BEGIN PGP SIGNATURE-----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=H2KZ
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.10-1
* Add last part of cleanup Cherryview driver to align with other drivers
* Due to above clean up Cherryview and Baytrail drivers to use common API
The following is an automated git shortlog grouped by driver:
baytrail:
- Switch to use intel_pinctrl_get_soc_data()
cherryview:
- Preserve CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs
- Switch to use intel_pinctrl_get_soc_data()
- Utilize temporary variable to hold device pointer
- Switch to use struct intel_pinctrl
- Move custom community members to separate data struct
- Drop stale comment
intel:
- Update header block to reflect direct dependencies
- Extract intel_pinctrl_get_soc_data() helper for wider use
- Add CAN and USB1 PWEN pin groups on R-Car H2 and RZ/G1,
- Three more conversion of DT bindings to json-schema,
- Group all Renesas pinctrl drivers and improve visual Kconfig
structure,
- Rename drivers/pinctrl/sh-pfc to drivers/pinctrl/renesas,
- Minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX2SoaQAKCRCKwlD9ZEnx
cKV6AP48BYvs8Fu3dd08ZRI3w82K56GQEi+9pJh+krkyQc8ODQD+JKbR48O15cN5
cQ0sJuVyAVRhEf9N7OerkbbBUCM+pQ8=
=jKcz
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.10
- Add CAN and USB1 PWEN pin groups on R-Car H2 and RZ/G1,
- Three more conversion of DT bindings to json-schema,
- Group all Renesas pinctrl drivers and improve visual Kconfig
structure,
- Rename drivers/pinctrl/sh-pfc to drivers/pinctrl/renesas,
- Minor fixes and improvements.
Most, but not all, Renesas pin control drivers use the "sh-pfc" pin
control framework. As of commit 8449bfa9e6a9f7ec ("pinctrl: sh-pfc:
Collect Renesas related CONFIGs in one place"), the code for this
framework is always built when Renesas SoC pin control support is
enabled, regardless of whether the enabled pin control drivers need it
or not.
Fix this by reintroducing the CONFIG_SH_PFC symbol to control inclusion
of the "sh-pfc" framework and its dependencies, and selecting it when
needed.
This reduces kernel size of a typical RZ/A1 or RZ/A2 kernel by more than
6 resp. 11 KiB.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200909131534.12897-4-geert+renesas@glider.be
The drivers/pinctrl/sh-pfc subdirectory was originally created to group
pin control drivers for various Renesas SuperH and SH-Mobile platforms.
However, the name "sh-pfc" no longer reflects its contents, as the
directory now contains pin control drivers for Renesas SuperH, ARM32,
and ARM64 SoCs.
Hence rename the subdirectory from drivers/pinctrl/sh-pfc to
drivers/pinctrl/renesas, and the related Kconfig symbol from
PINCTRL_SH_PFC to PINCTRL_RENESAS.
Rename the git branch in MAINTAINERS, too, for consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200909131534.12897-3-geert+renesas@glider.be
The RZ/N1 pin control driver does not use pin groups or pin functions,
so there is no need to select GENERIC_PINCTRL_GROUPS or
GENERIC_PINMUX_FUNCTIONS.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200909131534.12897-2-geert+renesas@glider.be
For pins requiring software driven IO output operations, the RZ/A1 Pin
Controller uses either the "output-high" or "output-low" DT property to
enable the corresponding output buffer. The actual line value doesn't
matter, as it is ignored.
Commit 425562429d ("pinctrl: generic: Add output-enable property")
introduced a new DT property for this specific use case.
Update the RZ/A1 Pin Controller DT bindings and driver to use this new
property instead. Preserve backwards compatibility with old DTBs in the
driver, as this comes at a very small cost.
Notes:
- The DT binding examples already used the new property,
- There are no upstream users of the old properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200821111401.4021-1-geert+renesas@glider.be
Now, Renesas Pin Control drivers are under menu, but current
descriptions are not aligned.
This patch aligns them.
- RZ/A2 gpio and pinctrl driver
- RZ/N1 pinctrl driver
- Emma Mobile EV2 pin control support
- R-Mobile APE6 pin control support
- R-Mobile A1 pin control support
- RZ/G1H pin control support
- RZ/G1M pin control support
+ pin control support for RZ/A2
+ pin control support for RZ/N1
+ pin control support for Emma Mobile EV2
+ pin control support for R-Mobile APE6
+ pin control support for R-Mobile A1
+ pin control support for RZ/G1H
+ pin control support for RZ/G1M
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87imd8y4r2.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Renesas related pinctrl CONFIGs are located in many places, which is
confusing.
This patch collects them into the same place, grouped in a new "Renesas
pinctrl drivers" menu.
This patch also moves pinctrl-rz{a1,a2,n1}.c into the sh-pfc folder.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k0xoy4r7.wl-kuninori.morimoto.gx@renesas.com
[geert: Update path in MAINTAINERS]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
It is "Emma Mobile EV2" not "AV2".
This patch tidies it up.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lfi4y4re.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
driver_deferred_probe_check_state() may return -ETIMEDOUT instead of
-EPROBE_DEFER after all built-in drivers have been probed. This can
cause issues for built-in drivers that depend on resources provided by
loadable modules.
One such case happens on Tegra where I2C controllers are used during
early boot to set up the system PMIC, so the I2C driver needs to be a
built-in driver. At the same time, some instances of the I2C controller
depend on the DPAUX hardware for pinmuxing. Since the DPAUX is handled
by the display driver, which is usually not built-in, the pin control
states will not become available until after the root filesystem has
been mounted and the display driver loaded from it.
Fixes: bec6c0ecb2 ("pinctrl: Remove use of driver_deferred_probe_check_state_continue()")
Suggested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200825143348.1358679-1-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I encountered bug in SX1502 expander driver in 5.7.7. Here is relevant
DTS part:
compatible = "semtech,sx1502q";
gpio4_cfg_pins: gpio2-cfg {
pins = "gpio5";
output-high;
};
And part of OOPS:
[ 0.673996] [<c023cfa6>] (gpiochip_get_data) from [<c023b235>]
(sx150x_gpio_direction_output+0xd)
[ 0.683259] [<c023b235>] (sx150x_gpio_direction_output) from
[<c023b363>] (sx150x_pinconf_set+0x)
[ 0.692796] [<c023b363>] (sx150x_pinconf_set) from [<c0238fef>]
(pinconf_apply_setting+0x39/0x7e)
[ 0.701635] [<c0238fef>] (pinconf_apply_setting) from [<c0236c77>]
(pinctrl_commit_state+0xa5/0x)
[ 0.710648] [<c0236c77>] (pinctrl_commit_state) from [<c0237e03>]
(pinctrl_enable+0xff/0x1d4)
[ 0.719139] [<c0237e03>] (pinctrl_enable) from [<c023b791>]
(sx150x_probe+0x1a3/0x358)
[ 0.727027] [<c023b791>] (sx150x_probe) from [<c02c38bf>]
(i2c_device_probe+0x1bb/0x1dc)
The problem is that sx150x_pinconf_set uses sx150x_gpio_direction_output
but gpio is not setup yet. Patch below fixes it but I'm not sure whether
is it correct.
Link: https://lore.kernel.org/r/f32130bf-cfd4-b1bf-538c-dbc9ee2d947a@eaxlabs.cz
Signed-off-by: Martin DEVERA <devik@eaxlabs.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Rockchip pinctrl driver needs to handle information from Devicetree
so only makes sense getting compiled on systems with CONFIG_OF enabled.
This also fixes a problem found by the "kernel-test-robot" when compiling
the driver on test-builds that do not have CONFIG_OF enabled:
drivers/pinctrl/pinctrl-rockchip.c: In function 'rockchip_pinctrl_parse_groups':
>> drivers/pinctrl/pinctrl-rockchip.c:2881:9: error: implicit declaration of function 'pinconf_generic_parse_dt_config'; did you mean 'pinconf_generic_dump_config'? [-Werror=implicit-function-declaration]
2881 | ret = pinconf_generic_parse_dt_config(np_config, NULL,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| pinconf_generic_dump_config
drivers/pinctrl/pinctrl-rockchip.c: In function 'rockchip_gpiolib_register':
>> drivers/pinctrl/pinctrl-rockchip.c:3473:5: error: 'struct gpio_chip' has no member named 'of_node'
3473 | gc->of_node = bank->of_node;
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200905214955.907950-1-heiko@sntech.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only usage of s900_padinfo[] is to assign it to the padinfo field in
the owl_pinctrl_soc_data struct, which is a const pointer. Make it const
to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200830224311.36994-4-rikard.falkeborn@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only usage of s700_padinfo[] is to assign it to the padinfo field in
the owl_pinctrl_soc_data struct, which is a const pointer. Make it const
to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200830224311.36994-3-rikard.falkeborn@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only usage of owl_pinctrl_ops and owl_pinmux_ops is to assign their
addresses to the pctlops and the pmxops fields in the pinctrl_desc struct,
which are const pointers. Make them const to allow the compiler to put them
in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200830224311.36994-2-rikard.falkeborn@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On page 23 of the datasheet [0] it says "The register remains unchanged
until the interrupt is cleared via a read of INTCAP or GPIO." Include
INTCAPA and INTCAPB registers in precious range, so that they aren't
accidentally cleared when we read via debugfs.
[0] https://ww1.microchip.com/downloads/en/DeviceDoc/20001952C.pdf
Fixes: 8f38910ba4 ("pinctrl: mcp23s08: switch to regmap caching")
Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200828213226.1734264-3-thomas.preston@codethink.co.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mcp23x17_regmap is initialised with structs named "mcp23x16".
However, the mcp23s08 driver doesn't support the MCP23016 device yet, so
this appears to be a typo.
Fixes: 8f38910ba4 ("pinctrl: mcp23s08: switch to regmap caching")
Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200828213226.1734264-2-thomas.preston@codethink.co.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One some devices the GPIO should output the inverted value from what
device-drivers / ACPI code expects. The reason for this is unknown,
perhaps these systems use an external buffer chip on the GPIO which
inverts the signal. The BIOS makes this work by setting the
CHV_PADCTRL1_INVRXTX_TXDATA flag.
Before this commit we would unconditionally clear all INVRXTX flags,
including the CHV_PADCTRL1_INVRXTX_TXDATA flag when a GPIO is requested
by a driver (from chv_gpio_request_enable()).
This breaks systems using this setup. Specifically it is causing
problems for systems with a goodix touchscreen, where the BIOS sets the
INVRXTX_TXDATA flag on the GPIO used for the touchscreen's reset pin.
The goodix touchscreen driver by defaults configures this pin as input
(relying on the pull-up to keep it high), but the clearing of the
INVRXTX_TXDATA flag done by chv_gpio_request_enable() causes it to be
driven low for a brief time before the GPIO gets set to input mode.
This causes the touchscreen controller to get reset. On most CHT devs
with this touchscreen this leads to:
[ 31.596534] Goodix-TS i2c-GDIX1001:00: i2c test failed attempt 1: -121
The driver retries this though and then everything is fine. But during
reset the touchscreen uses its interrupt pin as bootstrap to determine
which i2c address to use and on the Acer One S1003 the spurious reset
caused by the clearing of the INVRXTX_TXDATA flag causes the controller
to come back up again on the wrong i2c address, breaking things.
This commit fixes both the -121 errors, as well as the total breakage
on the Acer One S1003, by making chv_gpio_clear_triggering() not clear
the INVRXTX_TXDATA flag if the pin is already configured as a GPIO.
Note that chv_pinmux_set_mux() does still unconditionally clear the
flag, so this only affects GPIO usage.
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Print particular message in each of error case in the ->probe().
While here, use dev_err_probe() for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200828103235.78380-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial Qualcomm msm8226 pinctrl driver to support pin configuration
with pinctrl framework for msm8226 SoC.
- Initial formatting and style was taken from the msm8x74 pinctrl driver
added by Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Link: https://lore.kernel.org/r/20200716205530.22910-3-bartosz.dudziak@snejp.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Group name 'pcie1' is misleading as it controls only PCIe reset pin. Like
other PCIe groups it should have been called 'pcie1_reset'. But due to
backward compatibility it is not possible to change existing group name.
So just add comment describing this PCIe reset functionality.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200724132457.7094-1-pali@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The nomadik pinctrl hardware doesn't have any way to
determine if the active pull is up or down. Reading
the bit currently used to report if the pull is up/down
indicates if the gpio input is reading high or low, it
doesn't reflect the pull state.
For this reason change the output from "pull up"/"pull down" to
"pull enabled". This avoids confusing developers who were using
the output to determine what the pull state is.
Signed-off-by: Andrew Halaney <ajhalaney@gmail.com>
Link: https://lore.kernel.org/r/20200806155322.GA25523@ola-jn9phv2.ad.garmin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update header inclusion block to reflect all direct dependencies
that are being involved in pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we have common helper to retrieve SoC data from driver data
we may switch to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we have common helper to retrieve SoC data from driver data
we may switch to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
intel_pinctrl_get_soc_data() helper can be used in few driver instead of
open-coded variants. Thus, extract it as a standalone API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
By one of the previous clean up change we got a temporary variable to hold
a device pointer. It can be utilized in other calls in the ->probe() and
save a bit of LOCs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now when all preparations are done we may easily switch to use
struct intel_pinctrl instead of custom one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is a preparatory patch for bigger clean up pending for Cherryview driver.
There is no functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
