Implemented igb_ndo_set_vf_bw function which is being used
by iproute2 tool. In addition, updated igb_ndo_get_vf_config function
to show the actual rate limit to the user.
The rate limitation can be configured only when the link is up.
The rate limit value can be ranged between 0 and actual
link speed measured in Mbps. A value of '0' disables the rate limit for
this specific VF.
iproute2 usage will be 'ip link set ethX vf Y rate Z'.
After the command is made, the rate will be changed instantly.
To view the current rate limit, use 'ip link show ethX'.
The rates will be zeroed only upon driver reload or a link speed change.
This feature is being supported only by 82576 device.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds full support for SR-IOV by enabling the PF side.
VF side has already been committed.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables support for Intel i340 Quad Port Fiber Adapter.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for the anti-spoofing feature in the HW. Packets from
VF devices with spoofed MAC addresses or VLAN tags will be blocked
and an event generated. When the watchdog task runs it will call a
function to check if any spoof events occurred. If an event was
detected then a warning message is dumped to the system log.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does the following:
1. Changes the existing supported device id's so now DH89xxCC is not supported when EEPROM is not read.
2. Adds two more device ids for DH89xxCC in backplane mode and SFP.
3. Driver now initializes previously possibly uninitialized value in igb_reset_mdicnfg_82580().
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print a warning message to the system log when the VF attempts to
override administratively set MAC/VLAN configuration.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The vf flags were being overwritten causing the flag that indicates
that the PF has set the VF MAC address to get cleared. This would
allow the VF to override the MAC address assigned by the Host VMM
using the ip link set command.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All three drivers use flush_scheduled_work() similarly during driver
detach. Replace it with explicit cancels.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: e1000-devel@lists.sourceforge.net
Cc: netdev@vger.kernel.org
New adapters will have part numbers stored in string format rather than
simple hex format. This function will read part number formats in either
hex or string.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use vzalloc() and vzalloc_node() in net drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jon Mason <jon.mason@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit eab6d18d "vlan: Don't check for vlan group before
vlan_tx_tag_present" removed the need for the adapter variable
in igb_xmit_frame_ring_adv(). This removes the variable as well
to avoid the compiler warning.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many (but not all) drivers check to see whether there is a vlan
group configured before using a tag stored in the skb. There's
not much point in this check since it just throws away data that
should only be present in the expected circumstances. However,
it will soon be legal and expected to get a vlan tag when no
vlan group is configured, so remove this check from all drivers
to avoid dropping the tags.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN_GROUP_ARRAY_LEN is simply the number of possible vlan VIDs.
Since vlan groups will soon be more of an implementation detail
for vlan devices, rename the constant to be descriptive of its
actual purpose.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are currently some problems with igb.
- On 32bit arches, maintaining 64bit counters without proper
synchronization between writers and readers.
- Stats updated every two seconds, as reported by Jesper.
(Jesper provided a patch for this)
- Potential problem between worker thread and ethtool -S
This patch uses u64_stats_sync, and convert everything to be 64bit safe,
SMP safe, even on 32bit arches. It integrates Jesper idea of providing
accurate stats at the time user reads them.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the netdev->features is set with NETIF_F_HIGHDMA, we should set the
corresponding netdev->vlan_features as well to allow VLAN netdev created
on top of the real netdev to be able to also benefit from HIGHDMA on 32bit
system, reducing the performance hit that is caused by __skb_linearize(),
particularly for large send. This is fixed in this patch for all Intel e1000,
e1000e, igb, ixgbe, and ixgbe drivers since this should be beneficial
to all devices supported by these drivers.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the Intel(r) DH89xxCC series. The new
device will be using Intel(r) i347-AT4 and Marvell(r) M88E1322 and
M88E1112 PHYs. Support for these devices has also been added here.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects an issue in which we were setting all flag bits except
for promisc instead of clearing the promisc bits due to the incorrect use
of an |= instead of an &=.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"foo = &function" is more commonly written "foo = function"
Done with coccinelle script:
// <smpl>
@r@
identifier f;
@@
f(...) { ... }
@@
identifier r.f;
@@
- &f
+ f
// </smpl>
drivers/net/tehuti.c used a function and struct with the
same name, the function was renamed.
Compile tested x86 only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the abstraction introduced by the union skb_shared_tx in
the shared skb data.
The access of the different union elements at several places led to some
confusion about accessing the shared tx_flags e.g. in skb_orphan_try().
http://marc.info/?l=linux-netdev&m=128084897415886&w=2
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid more patches, I also fixed other spelling
and grammar bugs when they were in the same or
following line:
successfull -> successful
parse -> parses
controler -> controller
controlers -> controllers
Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on patches from Sonny Rao and Milton Miller...
Combined the patches to fix up clean_tx_irq and clean_rx_irq.
The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.
In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.
The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.
This bug was found during stress testing and adding this barrier has
been shown to fix it. The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().
This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.
Previously Submitted to e1000-devel only for ixgbe
http://marc.info/?l=e1000-devel&m=126593062701537&w=3
We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.
CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synchronize all IRQs when using MSI-X. Similar to ixgbe.
Issue was reported on e1000e, but the patch is also valid for igb.
CC: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ixgbe cards put an invalid VF device ID in the PCIe SR-IOV
capability. The ixgbe driver is only valid for PFs or non SR-IOV
hardware. It seems that the same problem could occur on igb hardware as
well, so if we discover we are trying to initialize a VF in ixbge_probe
or igb_probe, print an error and exit.
Based on a patch for ixgbe from Chris Wright <chrisw@sous-sol.org>.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Cc: Chris Wright <chrisw@sous-sol.org>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change removes UDP from the supported protocols for RSS hashing. The
reason for removing this protocol is because IP fragmentation was causing a
network flow to be broken into two streams, one for fragmented, and one for
non-fragmented and this in turn was causing out-of-order issues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add explanatory comment to avoid confusion when a pointer is set
to the second word of an array instead of the customary cast of a
pointer to the beginning of the array.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the value of max_vfs at the time of assignment of vfs_allocated_count.
The previous check in igb_probe_vfs was too late as by that time the rx/tx
rings were initialized with the wrong offset.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 82576 expects the second rx queue in any pool to receive L2 switch
loop back packets sent from the second tx queue in another pool. The
82576 VF driver does not enable the second rx queue so if the PF driver
sends packets destined to a VF from its second tx queue then the VF
driver will never see them. In SR-IOV mode limit the number of tx queues
used by the PF driver to one. This patch fixes a bug reported in which
the PF cannot communciate with the VF and should be considered for 2.6.34
stable.
CC: stable@kernel.org
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reduces the number of skb cache misses in the
clean_tx_irq path, and results in an overall increase
in tx packet throughput.
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds registers (,tx/rx rings' status and so on) printout
code just before resetting adapters. This will be helpful for detecting
the root cause of adapters reset.
Signed-off-by: Taku Izumi <izumi.taku@jp.fujitsu.com>
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that igb now uses the DMA API functions instead of
the PCI API functions. To do this the pci_dev pointer that was in the
rings has been replaced with a device pointer, and as a result all
references to [tr]x_ring->pdev have been replaced with [tr]x_ring->dev.
This patch is based of of work originally done by Nicholas Nunley.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects the fact that we were not reporting Gen2 link speeds
when we were in fact connected at Gen2 rates.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to increment nr_frags because skb_fill_page_desc increments
it.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restrict Wake-on-LAN to first port on 82576 ET2 quad port NICs, as it is
only supported there.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for per-packet timestamping for the
82580 adapter. The rx timestamp code is also pulled out of the
inlined rx hotpath and instead moved to a seperate function.
This version adds a comment explaining the per-packet timestamping
code added to igb_hwtstamp_ioctl().
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change updates the igb driver to make use of the netdev_dbg function
macros now provided in netdevice.h
This is meant to be provided as an alternative to the patch provided by
Joe Perches.
It also removes igb_get_time_str since I found that it is unused code that
is no longer used even in debug.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This change makes it so that vlan_gro_receive is only used if vlans have been
registered to the adapter structure. Previously we were just sending all vlan
tagged frames in via this function but this results in a null pointer
dereference when vlans are not registered.
[ This fixes bugzilla entry 15582 -Eric Dumazet]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the driver tweaked txqueuelen to avoid false Tx hang reports seen at half duplex.
This had the effect of overriding user set values on link change/reset. Testing shows that
adjusting only the timeout factor is sufficient to prevent Tx hang reports at half duplex.
Based on e1000e patch by Franco Fichtner <franco@lastsummer.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
