The DB8500 exists in an enhanced variant named DB8520
for some machines. To clearly distinguish between the
different machines, create an explicit db8500.dtsi
and move the operating points (only known difference so
far) to that file, so we can add an explicit db8520.dtsi
after this.
Cc: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191126124738.77690-1-linus.walleij@linaro.org
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have aliases for I2C and SPI in ste-dbx5x0.dtsi,
it does not make much sense to keep only the aliases for UART
separately in each board device tree.
Considering that all boards set the same aliases for the serial
ports there is no reason to keep them separated either.
Move them to ste-dbx5x0.dtsi and remove the aliases from the
board-specific device tree parts.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20191125170428.76069-3-stephan@gerhold.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In preparation to update to bu21013_tp driver properly annotate GPIOs
property (the INT GPIOs are active low, not open drain), and also define
interrupt lines so we do not have to have special conversion in the driver.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
the code contained herein is licensed under the gnu general public
license you may obtain a copy of the gnu general public license
version 2 or later at the following locations http www opensource
org licenses gpl license html http www gnu org copyleft gpl html
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This enumerates the PL011 serial ports on the Ux500. This is
necessary to do if we want to remove one of the serial ports,
since userspace depends on console to be present on ttyAMA2
and we must not break userspace.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The BU21013 touchscreen GPIOs have been pretty confused, correct
them per board, and move the GPIO assignments up to the top
level DTS file so we can control it from there, and avoid defining
the GPIO assignments for non-ST UIB equipped boards.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As the device tree conversion did away with the ability to
auto-detect the UIB (User Interface Board) version from attempting
to read an I2C address, we now have to pass the knowledge of
what UIB is mounted through the device tree. This gives rise
to four possible board permutations:
- HREF prior to v60, ST UIB (hrefprev60-stuib)
- HREF prior to v60, TVK1281618 UIB (hrefprev60-tvk)
- HREF v60 and later, ST UIB (href60plus-stuib)
- HREF v60 and later, TVK1281618 UIB (hrefv60plus-tvk)
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
