* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
xen-blkfront: fix missing out label
blkdev: fix blkdev_issue_zeroout return value
block: update request stacking methods to support discards
block: fix missing export of blk_types.h
writeback: fix bad _bh spinlock nesting
drbd: revert "delay probes", feature is being re-implemented differently
drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
drbd: Disable delay probes for the upcomming release
writeback: cleanup bdi_register
writeback: add new tracepoints
writeback: remove unnecessary init_timer call
writeback: optimize periodic bdi thread wakeups
writeback: prevent unnecessary bdi threads wakeups
writeback: move bdi threads exiting logic to the forker thread
writeback: restructure bdi forker loop a little
writeback: move last_active to bdi
writeback: do not remove bdi from bdi_list
writeback: simplify bdi code a little
writeback: do not lose wake-ups in bdi threads
...
Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
It was a now abandoned attempt to throttle resync bandwidth
based on the delay it causes on the bulk data socket.
It has no userbase yet, and has been disabled by
9173465ccb51c09cc3102a10af93e9f469a0af6f already.
This removes the now unused code.
The basic feature, namely using up "idle" bandwith
of network and disk IO subsystem, with minimal impact
to application IO, is being reimplemented differently.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
put_user() may fail, if so return -EFAULT.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If there's no feature-barrier key in xenstore, then it means its a fairly
old backend which does uncached in-order writes, which means ORDERED_DRAIN
is appropriate.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
When barriers are supported, then use QUEUE_ORDERED_TAG to tell the block
subsystem that it doesn't need to do anything else with the barriers.
Previously we used ORDERED_DRAIN which caused the block subsystem to
drain all pending IO before submitting the barrier, which would be
very expensive.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
The struct cont_t is just a set of virtual function pointers.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Use memdup_user when user data is immediately copied into the
allocated region. Some checkpatch cleanups in nearby code.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
position p;
identifier l1,l2;
@@
- to = \(kmalloc@p\|kzalloc@p\)(size,flag);
+ to = memdup_user(from,size);
if (
- to==NULL
+ IS_ERR(to)
|| ...) {
<+... when != goto l1;
- -ENOMEM
+ PTR_ERR(to)
...+>
}
- if (copy_from_user(to, from, size) != 0) {
- <+... when != goto l2;
- -EFAULT
- ...+>
- }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Chirag Kantharia <chirag.kantharia@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: cleanup interrupt_not_for_us
In the case of MSI/MSIX interrutps, we don't need to check
if the interrupt is for us, and in the case of the intx interrupt
handler, when checking if the interrupt is for us, we don't need
to check if we're using MSI/MSIX, we know we're not.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: change printks to dev_warn, etc.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: separate cmd_alloc() and cmd_special_alloc()
cmd_alloc() took a parameter which caused it to either allocate
from a pre-allocated pool, or allocate using pci_alloc_consistent.
This parameter is always known at compile time, so this would
be better handled by breaking the function into two functions
and differentiating the cases by function names. Same goes
for cmd_free().
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: use consistent variable names
"h", for the hba structure and "c" for the command structures.
and get rid of trivial CCISS_LOCK macro.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: forbid hard reset of 640x boards
The 6402/6404 are two PCI devices -- two Smart Array controllers
-- that fit into one slot. It is possible to reset them independently,
however, they share a battery backed cache module. One of the pair
controls the cache and the 2nd one access the cache through the first
one. If you reset the one controlling the cache, the other one will
not be a happy camper. So we just forbid resetting this conjoined
mess.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: sanitize max commands
Some controllers might try to tell us they support 0 commands
in performant mode. This is a lie told by buggy firmware.
We have to be wary of this lest we try to allocate a negative
number of command blocks, which will be treated as unsigned,
and get an out of memory condition.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: Fix hard reset code.
Smart Array controllers newer than the P600 do not honor the
PCI power state method of resetting the controllers. Instead,
in these cases we can get them to reset via the "doorbell" register.
This escaped notice until we began using "performant" mode because
the fact that the controllers did not reset did not normally
impede subsequent operation, and so things generally appeared to
"work". Once the performant mode code was added, if the controller
does not reset, it remains in performant mode. The code immediately
after the reset presumes the controller is in "simple" mode
(which previously, it had remained in simple mode the whole time).
If the controller remains in performant mode any code which presumes
it is in simple mode will not work. So the reset needs to be fixed.
Unfortunately there are some controllers which cannot be reset by
either method. (eg. p800). We detect these cases by noticing that
the controller seems to remain in performant mode even after a
reset has been attempted. In those cases we ignore the controller,
as any commands outstanding on it will result in stale completions.
To sum up, we try to do a better job of resetting the controller if
"reset_devices" is set, and if it doesn't work, we ignore that
controller.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_reset_devices()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Rationale for this is that I will also need to use this code
in fixing kdump host reset code prior to having the hba structure.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_enter_performant_mode
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_wait_for_mode_change_ack()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: make cciss_put_controller_into_performant_mode as __devinit
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_p600_dma_prefetch_quirk()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_enable_scsi_prefetch()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out CISS_signature_present()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_find_board_params
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: fix leak of ioremapped memory
in cciss_pci_init error path.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_wait_for_board_ready()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_find_memory_BAR()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: remove board_id parameter from cciss_interrupt_mode()
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: factor out cciss_lookup_board_id
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: save pdev pointer in per hba structure early to avoid passing it around so much.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
cciss: Set the performant mode bit in the scsi half of the driver
In a couple of places, the performant mode bit wasn't being set in
the scsi half of the driver, causing commands to seem to hang. Use
enqueue_cmd_and_start_io() where appropriate. This fixes a bug that
echo engage scsi > /proc/driver/cciss/cciss0
would hang.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is just bd_openers, protected by the bd_mutex.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is just bd_openers, protected by the bd_mutex.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Same approach as blkfront_closing:
* Grab the bdev safely, holding the info mutex.
* Zap xbdev safely, holding the info mutex.
* Try bdev removal safely, holding bd_mutex.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
We cannot read backend state within bdev operations, because it risks
grabbing the state change before xenbus gets to do it.
Fixed by tracking deferral with a frontend switch to Closing. State
exposure isn't strictly necessary, but the backends won't mind.
For a 'clean' deferral this seems actually a more decent protocol than
raising errors.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We need not mind if users grab a late handle on a closing disk. We
probably even should not. But we have to make sure it's not a dead
one already
Let the bdev deal with a gendisk deleted under its feet. Takes the
info mutex to decide a race against backend closing.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The bdev .open/.release fops race against backend switches to Closing,
handled by the XenBus thread.
The original code attempted to serialize block device holders and
xenbus only via bd_mutex. This is insufficient, the info->bd pointer
may already be stale (or null) while xenbus tries to bump up the
refcount.
Protect blkfront_info with a dedicated mutex.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
* Current blkfront_closing is rather a xlvbd_release_gendisk.
Renamed in preparation of later patches (need the name again).
* Removed the misleading comment -- this only applied to the backend
switch handler, and the queue is already flushed btw.
* Break out the xenbus call, callers know better when to switch
frontend state.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The call to del_gendisk follows an non-refcounted gd->queue
pointer. We release the last ref in blk_cleanup_queue. Fixed by
reordering releases accordingly.
Signed-off-by: Daniel Stodden <daniel.stodden@citrix.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Fix:
drivers/block/xen-blkfront.c: In function ‘blkfront_connect’:
drivers/block/xen-blkfront.c:933: warning: enumeration value ‘BLKIF_STATE_DISCONNECTED’ not handled in switch
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Support dynamic resizing of virtual block devices. This patch supports
both file backed block devices as well as physical devices that can be
dynamically resized on the host side.
Signed-off-by: K. Y. Srinivasan <ksrinivasan@novell.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
