... since, of course, it's not used outside this driver.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Intel IDE-R devices are part of the Intel AMT management setup. They don't
have any special configuration registers or settings so the ata_generic
driver will support them fully.
Rather than add a huge table of IDs for each chipset and keep sending in
new ones this patch autodetects them.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Until now identifying that a device supports WRITE SAME(16) with the
UNMAP bit set has been black magic. Implement support for the SBC-3
Thin Provisioning VPD page and set the TPWS bit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that libata provides proper cross-port EH exclusion. The SIDPR
locking added by commit 213373cf (ata_piix: fix locking around SIDPR
access) is no longer necessary. Remove it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
In libata, the non-EH code paths should always take and release
ap->lock explicitly when accessing hardware or shared data structures.
However, once EH is active, it's assumed that the port is owned by EH
and EH methods don't explicitly take ap->lock unless race from irq
handler or other code paths are expected. However, libata EH didn't
guarantee exclusion among EHs for ports of the same host. IOW,
multiple EHs may execute in parallel on multiple ports of the same
controller.
In many cases, especially in SATA, the ports are completely
independent of each other and this doesn't cause problems; however,
there are cases where different ports share the same resource, which
lead to obscure timing related bugs such as the one fixed by commit
213373cf (ata_piix: fix locking around SIDPR access).
This patch implements exclusion among EHs of the same host. When EH
begins, it acquires per-host EH ownership by calling ata_eh_acquire().
When EH finishes, the ownership is released by calling
ata_eh_release(). EH ownership is also released whenever the EH
thread goes to sleep from ata_msleep() or explicitly and reacquired
after waking up.
This ensures that while EH is actively accessing the hardware, it has
exclusive access to it while allowing EHs to interleave and progress
in parallel as they hit waiting stages, which dominate the time spent
in EH. This achieves cross-port EH exclusion without pervasive and
fragile changes while still allowing parallel EH for the most part.
This was first reported by yuanding02@gmail.com more than three years
ago in the following bugzilla. :-)
https://bugzilla.kernel.org/show_bug.cgi?id=8223
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Reported-by: yuanding02@gmail.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Add optional @ap argument to ata_wait_register() and replace msleep()
calls with ata_msleep() which take optional @ap in addition to the
duration. These will be used to implement EH exclusion.
This patch doesn't cause any behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Now that DIPM can be used independently from HIPM, ata_piix can
support LPM too.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Port multipliers can do DIPM on fan-out links fine. Implement support
for it. Tested w/ SIMG 57xx and marvell PMPs. Both the host and
fan-out links enter power save modes nicely.
SIMG 37xx and 47xx report link offline on SStatus causing EH to detach
the devices. Blacklisted.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The current LPM implementation has the following issues.
* Operation order isn't well thought-out. e.g. HIPM should be
configured after IPM in SControl is properly configured. Not the
other way around.
* Suspend/resume paths call ata_lpm_enable/disable() which must only
be called from EH context directly. Also, ata_lpm_enable/disable()
were called whether LPM was in use or not.
* Implementation is per-port when it should be per-link. As a result,
it can't be used for controllers with slave links or PMP.
* LPM state isn't managed consistently. After a link reset for
whatever reason including suspend/resume the actual LPM state would
be reset leaving ap->lpm_policy inconsistent.
* Generic/driver-specific logic boundary isn't clear. Currently,
libahci has to mangle stuff which libata EH proper should be
handling. This makes the implementation unnecessarily complex and
fragile.
* Tied to ALPM. Doesn't consider DIPM only cases and doesn't check
whether the device allows HIPM.
* Error handling isn't implemented.
Given the extent of mismatch with the rest of libata, I don't think
trying to fix it piecewise makes much sense. This patch reimplements
LPM support.
* The new implementation is per-link. The target policy is still
port-wide (ap->target_lpm_policy) but all the mechanisms and states
are per-link and integrate well with the rest of link abstraction
and can work with slave and PMP links.
* Core EH has proper control of LPM state. LPM state is reconfigured
when and only when reconfiguration is necessary. It makes sure that
LPM state is reset when probing for new device on the link.
Controller agnostic logic is now implemented in libata EH proper and
driver implementation only has to deal with controller specifics.
* Proper error handling. LPM config failure is attributed to the
device on the link and LPM is disabled for the link if it fails
repeatedly.
* ops->enable/disable_pm() are replaced with single ops->set_lpm()
which takes @policy and @hints. This simplifies driver specific
implementation.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management is about to be reimplemented. Prepare for it.
* Implement sata_link_scr_lpm().
* Drop static from ata_dev_set_feature() and make it available to
other libata files.
* Trivial whitespace adjustments.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Link power management related symbols are in confusing state w/ mixed
usages of lpm, ipm and pm. This patch cleans up lpm related symbols
and sysfs show/store functions as follows.
* lpm states - NOT_AVAILABLE, MIN_POWER, MAX_PERFORMANCE and
MEDIUM_POWER are renamed to ATA_LPM_UNKNOWN and
ATA_LPM_{MIN|MAX|MED}_POWER.
* Pre/postfixes are unified to lpm.
* sysfs show/store functions for link_power_management_policy were
curiously named get/put and unnecessarily complex. Renamed to
show/store and simplified.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This build error showed up in linux-next tag next-20100820 for ia64:
WARNING: vmlinux.o(.init.text+0x4a952): Section mismatch in reference from the function ata_init() to the function .exit.text:ata_sff_exit()
The function __init ata_init() references
a function __exit ata_sff_exit().
This is often seen when error handling in the init function
uses functionality in the exit path.
The fix is often to remove the __exit annotation of
ata_sff_exit() so it may be used outside an exit section.
Sure enough, dropping the __exit fixes the problem.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This change enables my x86 machine to recognize and talk to a
"Native 4K" SATA device.
When I started working on this, I didn't know Matthew Wilcox had
posted a similar patch 2 years ago:
http://git.kernel.org/?p=linux/kernel/git/willy/ata.git;a=shortlog;h=refs/heads/ata-large-sectors
Gwendal Grignou pointed me at the the above code and small portions of
this patch include Matthew's work. That's why Mathew is first on the
"Signed-off-by:". I've NOT included his use of a bitmap to determine
512 vs Native for ATA command block size - just used a simple table.
And bugs are almost certainly mine.
Lastly, the patch has been tested with a native 4K 'Engineering
Sample' drive provided by Hitachi GST.
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Grant Grundler <grundler@google.com>
Reviewed-by: Gwendal Grignou <gwendal@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Currently, sata_fsl, mv and nv call ata_qc_complete() multiple times
from their interrupt handlers to indicate completion of NCQ commands.
This limits the visibility the libata core layer has into how commands
are being executed and completed, which is necessary to support IRQ
expecting in generic way. libata already has an interface to complete
multiple commands at once - ata_qc_complete_multiple() which ahci and
sata_sil24 already use.
This patch updates the three drivers to use ata_qc_complete_multiple()
too and updates comments on ata_qc_complete[_multiple]() regarding
their usages with NCQ completions. This change not only provides
better visibility into command execution to the core layer but also
simplifies low level drivers.
* sata_fsl: It already builds done_mask. Conversion is straight
forward.
* sata_mv: mv_process_crpb_response() no longer checks for illegal
completions, it just returns whether the tag is completed or not.
mv_process_crpb_entries() builds done_mask from it and passes it to
ata_qc_complete_multiple() which will check for illegal completions.
* sata_nv adma: Similar to sata_mv. nv_adma_check_cpb() now just
returns the tag status and nv_adma_interrupt() builds done_mask from
it and passes it to ata_qc_complete_multiple().
* sata_nv swncq: It already builds done_mask. Drop unnecessary
illegal transition checks and call ata_qc_complete_multiple().
In the long run, it might be a good idea to make ata_qc_complete()
whine if called when multiple NCQ commands are in flight.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ashish Kalra <ashish.kalra@freescale.com>
Cc: Saeed Bishara <saeed@marvell.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This is a scheleton for libata transport class.
All information is read only, exporting information from libata:
- ata_port class: one per ATA port
- ata_link class: one per ATA port or 15 for SATA Port Multiplier
- ata_device class: up to 2 for PATA link, usually one for SATA.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (278 commits)
arm: remove machine_desc.io_pg_offst and .phys_io
arm: use addruart macro to establish debug mappings
arm: return both physical and virtual addresses from addruart
arm/debug: consolidate addruart macros for CONFIG_DEBUG_ICEDCC
ARM: make struct machine_desc definition coherent with its comment
eukrea_mbimxsd-baseboard: Pass the correct GPIO to gpio_free
cpuimx27: fix compile when ULPI is selected
mach-pcm037_eet: fix compile errors
Fixing ethernet driver compilation error for i.MX31 ADS board
cpuimx51: update board support
mx5: add cpuimx51sd module and its baseboard
iomux-mx51: fix GPIO_1_xx 's IOMUX configuration
imx-esdhc: update devices registration
mx51: add resources for SD/MMC on i.MX51
iomux-mx51: fix SD1 and SD2's iomux configuration
clock-mx51: rename CLOCK1 to CLOCK_CCGR for better readability
clock-mx51: factorize clk_set_parent and clk_get_rate
eukrea_mbimxsd: add support for DVI displays
cpuimx25 & cpuimx35: fix OTG port registration in host mode
i.MX31 and i.MX35 : fix errate TLSbo65953 and ENGcm09472
...
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags:
Fix IRQ flag handling naming
MIPS: Add missing #inclusions of <linux/irq.h>
smc91x: Add missing #inclusion of <linux/irq.h>
Drop a couple of unnecessary asm/system.h inclusions
SH: Add missing consts to sys_execve() declaration
Blackfin: Rename IRQ flags handling functions
Blackfin: Add missing dep to asm/irqflags.h
Blackfin: Rename DES PC2() symbol to avoid collision
Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
Blackfin: Split PLL code from mach-specific cdef headers
* 'next-spi' of git://git.secretlab.ca/git/linux-2.6: (53 commits)
spi/omap2_mcspi: Verify TX reg is empty after TX only xfer with DMA
spi/omap2_mcspi: disable channel after TX_ONLY transfer in PIO mode
spi/bfin_spi: namespace local structs
spi/bfin_spi: init early
spi/bfin_spi: check per-transfer bits_per_word
spi/bfin_spi: warn when CS is driven by hardware (CPHA=0)
spi/bfin_spi: cs should be always low when a new transfer begins
spi/bfin_spi: fix typo in comment
spi/bfin_spi: reject unsupported SPI modes
spi/bfin_spi: use dma_disable_irq_nosync() in irq handler
spi/bfin_spi: combine duplicate SPI_CTL read/write logic
spi/bfin_spi: reset ctl_reg bits when setup is run again on a device
spi/bfin_spi: push all size checks into the transfer function
spi/bfin_spi: use nosync when disabling the IRQ from the IRQ handler
spi/bfin_spi: sync hardware state before reprogramming everything
spi/bfin_spi: save/restore state when suspending/resuming
spi/bfin_spi: redo GPIO CS handling
Blackfin: SPI: expand SPI bitmasks
spi/bfin_spi: use the SPI namespaced bit names
spi/bfin_spi: drop extra memory we don't need
...
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (96 commits)
apic, x86: Use BIOS settings for IBS and MCE threshold interrupt LVT offsets
apic, x86: Check if EILVT APIC registers are available (AMD only)
x86: ioapic: Call free_irte only if interrupt remapping enabled
arm: Use ARCH_IRQ_INIT_FLAGS
genirq, ARM: Fix boot on ARM platforms
genirq: Fix CONFIG_GENIRQ_NO_DEPRECATED=y build
x86: Switch sparse_irq allocations to GFP_KERNEL
genirq: Switch sparse_irq allocator to GFP_KERNEL
genirq: Make sparse_lock a mutex
x86: lguest: Use new irq allocator
genirq: Remove the now unused sparse irq leftovers
genirq: Sanitize dynamic irq handling
genirq: Remove arch_init_chip_data()
x86: xen: Sanitise sparse_irq handling
x86: Use sane enumeration
x86: uv: Clean up the direct access to irq_desc
x86: Make io_apic.c local functions static
genirq: Remove irq_2_iommu
x86: Speed up the irq_remapped check in hot pathes
intr_remap: Simplify the code further
...
Fix up trivial conflicts in arch/x86/Kconfig
* 'x86-idle-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hotplug: In the MWAIT case of play_dead, CLFLUSH the cache line
x86, hotplug: Move WBINVD back outside the play_dead loop
x86, hotplug: Use mwait to offline a processor, fix the legacy case
x86, mwait: Move mwait constants to a common header file
* 'x86-amd-nb-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, amd_nb: Enable GART support for AMD family 0x15 CPUs
x86, amd: Use compute unit information to determine thread siblings
x86, amd: Extract compute unit information for AMD CPUs
x86, amd: Add support for CPUID topology extension of AMD CPUs
x86, nmi: Support NMI watchdog on newer AMD CPU families
x86, mtrr: Assume SYS_CFG[Tom2ForceMemTypeWB] exists on all future AMD CPUs
x86, k8: Rename k8.[ch] to amd_nb.[ch] and CONFIG_K8_NB to CONFIG_AMD_NB
x86, k8-gart: Decouple handling of garts and northbridges
x86, cacheinfo: Fix dependency of AMD L3 CID
x86, kvm: add new AMD SVM feature bits
x86, cpu: Fix allowed CPUID bits for KVM guests
x86, cpu: Update AMD CPUID feature bits
x86, cpu: Fix renamed, not-yet-shipping AMD CPUID feature bit
x86, AMD: Remove needless CPU family check (for L3 cache info)
x86, tsc: Remove CPU frequency calibration on AMD
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (29 commits)
sched: Export account_system_vtime()
sched: Call tick_check_idle before __irq_enter
sched: Remove irq time from available CPU power
sched: Do not account irq time to current task
x86: Add IRQ_TIME_ACCOUNTING
sched: Add IRQ_TIME_ACCOUNTING, finer accounting of irq time
sched: Add a PF flag for ksoftirqd identification
sched: Consolidate account_system_vtime extern declaration
sched: Fix softirq time accounting
sched: Drop group_capacity to 1 only if local group has extra capacity
sched: Force balancing on newidle balance if local group has capacity
sched: Set group_imb only a task can be pulled from the busiest cpu
sched: Do not consider SCHED_IDLE tasks to be cache hot
sched: Drop all load weight manipulation for RT tasks
sched: Create special class for stop/migrate work
sched: Unindent labels
sched: Comment updates: fix default latency and granularity numbers
tracing/sched: Add sched_pi_setprio tracepoint
sched: Give CPU bound RT tasks preference
sched: Try not to migrate higher priority RT tasks
...
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
lockdep: Check the depth of subclass
lockdep: Add improved subclass caching
affs: Use sema_init instead of init_MUTEX
hfs: Convert tree_lock to mutex
arm: Bcmring: semaphore cleanup
printk: Make console_sem a semaphore not a pseudo mutex
drivers/macintosh/adb: Do not claim that the semaphore is a mutex
parport: Semaphore cleanup
irda: Semaphore cleanup
net: Wan/cosa.c: Convert "mutex" to semaphore
net: Ppp_async: semaphore cleanup
hamradio: Mkiss: semaphore cleanup
hamradio: 6pack: semaphore cleanup
net: 3c527: semaphore cleanup
input: Serio/hp_sdc: semaphore cleanup
input: Serio/hil_mlc: semaphore cleanup
input: Misc/hp_sdc_rtc: semaphore cleanup
lockup_detector: Make callback function static
lockup detector: Fix grammar by adding a missing "to" in the comments
lockdep: Remove __debug_show_held_locks
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/amd-iommu: Update copyright headers
x86/amd-iommu: Reenable AMD IOMMU if it's mysteriously vanished over suspend
AGP: Warn when GATT memory cannot be set to UC
x86, GART: Disable GART table walk probes
x86, GART: Remove superfluous AMD64_GARTEN
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (26 commits)
selinux: include vmalloc.h for vmalloc_user
secmark: fix config problem when CONFIG_NF_CONNTRACK_SECMARK is not set
selinux: implement mmap on /selinux/policy
SELinux: allow userspace to read policy back out of the kernel
SELinux: drop useless (and incorrect) AVTAB_MAX_SIZE
SELinux: deterministic ordering of range transition rules
kernel: roundup should only reference arguments once
kernel: rounddown helper function
secmark: export secctx, drop secmark in procfs
conntrack: export lsm context rather than internal secid via netlink
security: secid_to_secctx returns len when data is NULL
secmark: make secmark object handling generic
secmark: do not return early if there was no error
AppArmor: Ensure the size of the copy is < the buffer allocated to hold it
TOMOYO: Print URL information before panic().
security: remove unused parameter from security_task_setscheduler()
tpm: change 'tpm_suspend_pcr' to be module parameter
selinux: fix up style problem on /selinux/status
selinux: change to new flag variable
selinux: really fix dependency causing parallel compile failure.
...
* 'virtio' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
virtio_blk: remove BKL leftovers
virtio: console: Disable lseek(2) for port file operations
virtio: console: Send SIGIO in case of port unplug
virtio: console: Send SIGIO on new data arrival on ports
virtio: console: Send SIGIO to processes that request it for host events
virtio: console: Reference counting portdev structs is not needed
virtio: console: Add reference counting for port struct
virtio: console: Use cdev_alloc() instead of cdev_init()
virtio: console: Add a find_port_by_devt() function
virtio: console: Add a list of portdevs that are active
virtio: console: open: Use a common path for error handling
virtio: console: remove_port() should return void
virtio: console: Make write() return -ENODEV on hot-unplug
virtio: console: Make read() return -ENODEV on hot-unplug
virtio: console: Unblock poll on port hot-unplug
virtio: console: Un-block reads on chardev close
virtio: console: Check if portdev is valid in send_control_msg()
virtio: console: Remove control vq data only if using multiport support
virtio: console: Reset vdev before removing device
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (22 commits)
ceph: do not carry i_lock for readdir from dcache
fs/ceph/xattr.c: Use kmemdup
rbd: passing wrong variable to bvec_kunmap_irq()
rbd: null vs ERR_PTR
ceph: fix num_pages_free accounting in pagelist
ceph: add CEPH_MDS_OP_SETDIRLAYOUT and associated ioctl.
ceph: don't crash when passed bad mount options
ceph: fix debugfs warnings
block: rbd: removing unnecessary test
block: rbd: fixed may leaks
ceph: switch from BKL to lock_flocks()
ceph: preallocate flock state without locks held
ceph: add pagelist_reserve, pagelist_truncate, pagelist_set_cursor
ceph: use mapping->nrpages to determine if mapping is empty
ceph: only invalidate on check_caps if we actually have pages
ceph: do not hide .snap in root directory
rbd: introduce rados block device (rbd), based on libceph
ceph: factor out libceph from Ceph file system
ceph-rbd: osdc support for osd call and rollback operations
ceph: messenger and osdc changes for rbd
...
Structure new_line is copied to userland with some padding fields unitialized.
It leads to leaking of stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
CC: stable@kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
With all the patches we have queued in the BKL removal tree, only a
few dozen modules are left that actually rely on the BKL, and even
there are lots of low-hanging fruit. We need to decide what to do
about them, this patch illustrates one of the options:
Every user of the BKL is marked as 'depends on BKL' in Kconfig,
and the CONFIG_BKL becomes a user-visible option. If it gets
disabled, no BKL using module can be built any more and the BKL
code itself is compiled out.
The one exception is file locking, which is practically always
enabled and does a 'select BKL' instead. This effectively forces
CONFIG_BKL to be enabled until we have solved the fs/lockd
mess and can apply the patch that removes the BKL from fs/locks.c.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fix
drivers/edac/mce_amd.c:262: warning: left shift count >= width of type
on 32-bit builds.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
F11h has almost the same MCE signatures as K8 except DRAM ECC and MC5
bank errors. Reuse functionality from the other families.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Now that all decoders have been taught about F14h, models < 0x10
MCEs, enable decoding on this family of CPUs. Also, issue a short
informational message upon boot that MCE decoding gets enabled.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
F14h CPUs do not generate LS MCEs so exit early and warn the user in
case this path is ever hit that something else might be going haywire.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add support for IC MCEs for F14h CPUs. K8 and F10h are almost identical
so use one function for both.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add a per-family data cache decoders. Since there is a certain overlap
between the different DC MCE signatures, reuse functionality between the
families as far as possible.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Drop "edac_" string from the filenames since they're prefixed with edac/
in their pathname anyway.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Add sysfs injection facilities for testing of the MCE decoding code.
Remove large parts of amd64_edac_dbg.c, as a result, which did only
NB MCE injection anyway and the new injection code supports that
functionality already.
Add an injection module so that MCE decoding code in production kernels
like those in RHEL and SLES can be tested.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Move toplevel sysfs class to the stub and make it available to
non-modularized code too. Add proper refcounting of its users and move
the registration functionality into the reference counting routines.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
... instead of the MCi_STATUS info only for improved handling of certain
types of errors later.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
.. so that the user knows what she's looking at there in dmesg. Also,
fix a minor cosmetic output inconsistency.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
If we get a bit-flip of ECC error while reading the data area, do not add it to
corrupted list, because it is possible that this is just unstable PEB with
corruptions caused by unclean reboots.
This patch also improves commentaries.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
When the data does not contain all 0xFF bytes, 'check_data_ff()' should return
1, not -EINVAL; Also, the caller ('process_eb()') should not add the PEB to the
"corrupted" list if there was a read error.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
While scanning the flash we read all VID headers and store some important
information in 'struct ubi_scan_leb'. Store also the 'copy_flag' value there
as it is needed when comparing LEBs. We do not increase memory consumption
because this is just one bit and we have plenty of spare bits in
'struct ubi_scan_leb' (sizeof(struct ubi_scan_leb) is 48 both with and
without this patch).
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Remove the BKL usage added in "block: push down BKL into .locked_ioctl".
Virtio-blk doesn't use the BKL for anything, and doesn't implement any
ioctl command by itself, but only uses the generic scsi_cmd_ioctl
which is fine without the BKL.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The ports are char devices; do not have seeking capabilities. Calling
nonseekable_open() from the fops_open() call and setting the llseek fops
pointer to no_llseek ensures an lseek() call from userspace returns
-ESPIPE.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If a port has registered for SIGIO signals, let the application
know that the port is getting unplugged.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Send a SIGIO signal when new data arrives on a port. This is sent only
when the process has requested for the signal to be sent using fcntl().
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A process can request for SIGIO on host connect / disconnect events
using the O_ASYNC file flag using fcntl().
If that's requested, and if the guest-side connection for the port is
open, any host-side open/close events for that port will raise a SIGIO.
The process can then use poll() within the signal handler to find out
which port triggered the signal.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Explain in a comment why there's no need to reference-count the portdev
struct: when a device is yanked out, we can't do anything more with it
anyway so just give up doing anything more with the data or the vqs and
exit cleanly.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When a port got hot-unplugged, when a port was open, any file operation
after the unplugging resulted in a crash. This is fixed by ref-counting
the port structure, and releasing it only when the file is closed.
This splits the unplug operation in two parts: first marks the port
as unavailable, removes all the buffers in the vqs and removes the port
from the per-device list of ports. The second stage, invoked when all
references drop to zero, releases the chardev and frees all other memory.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This moves to using cdev on the heap instead of it being embedded in the
ports struct. This helps individual refcounting and will allow us to
properly remove cdev structs after hot-unplugs and close operations.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To convert to using cdev as a pointer to avoid kref troubles, we have to
use a different method to get to a port from an inode than the current
container_of method.
Add find_port_by_devt() that looks up all portdevs and ports with those
portdevs to find the right port.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The virtio_console.c driver is capable of handling multiple devices at a
time. Maintain a list of devices for future traversal.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When a port is removed, we have to assume the port is gone. So a
success/failure return value doesn't make sense.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When a port is hot-unplugged while an app was blocked on a write() call,
the call was unblocked but would not get an error returned.
Return -ENODEV to ensure the app knows the port has gone away.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When a port is hot-unplugged while an app was blocked on a read() call,
the call was unblocked but would not get an error returned.
Return -ENODEV to ensure the app knows the port has gone away.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
When a port is hot-unplugged while an app is blocked on poll(), unblock
the poll() and return.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If a chardev is closed, any blocked read / poll calls should just return
and not attempt to use other state.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
A portdev may have been hot-unplugged while a port was open()ed. Skip
sending control messages when the portdev isn't valid.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If a portdev isn't using multiport support, it won't have any control vq
data to remove.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The virtqueues should be disabled before attempting to remove the
device.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Fix the following warning:
drivers/char/tpm/tpm.c:1085: warning: `tpm_suspend_setup' defined but not used
and make the workaround operable in case when TPM is compiled as a module.
As a side-effect the option will be called tpm.suspend_pcr.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: David Safford <safford@watson.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Debora Velarde <debora@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
We should be passing "buf" here insead of "bv". This is tricky because
it's not the same as kmap() and kunmap(). GCC does warn about it if you
compile on i386 with CONFIG_HIGHMEM.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
ceph_alloc_page_vector() returns ERR_PTR(-ENOMEM) on errors.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
rbd_client_create() doesn't free rbdc, this leads to many leaks.
seg_len in rbd_do_op() is unsigned, so (seg_len < 0) makes no sense.
Also if fixed check fails then seg_name is leaked.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
The rados block device (rbd), based on osdblk, creates a block device
that is backed by objects stored in the Ceph distributed object storage
cluster. Each device consists of a single metadata object and data
striped over many data objects.
The rbd driver supports read-only snapshots.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: O32 compat/N32: Fix to use compat syscall wrappers for AIO syscalls.
MAINTAINERS: Change list for ioc_serial to linux-serial.
SERIAL: ioc3_serial: Return -ENOMEM on memory allocation failure
MIPS: jz4740: Fix Kbuild Platform file.
MIPS: Repair Kbuild make clean breakage.
If the host is slow in reading data or doesn't read data at all,
blocking write calls not only blocked the program that called write()
but the entire guest itself.
To overcome this, let's not block till the host signals it has given
back the virtio ring element we passed it. Instead, send the buffer to
the host and return to userspace. This operation then becomes similar
to how non-blocking writes work, so let's use the existing code for this
path as well.
This code change also ensures blocking write calls do get blocked if
there's not enough room in the virtio ring as well as they don't return
-EAGAIN to userspace.
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: stable@kernel.org
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case of TX only with DMA, the driver assumes that the data
has been transferred once DMA callback in invoked. However,
SPI's shift register may still contain data. Thus, the driver
is supposed to verify that the register is empty and the end of
the SPI transfer has been reached.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In the TX_ONLY transfer, the SPI controller also receives data
simultaneously and saves them in the rx register. After the TX_ONLY
transfer, the rx register will hold the random data received during
the last tx transaction.
If the direct following transfer is RX_ONLY, this random data has the
possibility to affect this transfer like this:
When the SPI controller is changed from TX_ONLY to RX_ONLY,
the random data makes the rx register full immediately and
triggers a dummy write automatically(in SPI RX_ONLY transfers,
we need a dummy write to trigger the first transaction).
So the first data received in the RX_ONLY transfer will be that
random data instead of something meaningful.
We can avoid this by inserting a Disable/Re-enable toggle of the
channel after the TX_ONLY transfer, since it purges the rx register.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
There may be wakeup sources that aren't associated with any devices
and their statistics information won't be available from sysfs. Also,
for debugging purposes it is convenient to have all of the wakeup
sources statistics available from one place. For these reasons,
introduce new file "wakeup_sources" in debugfs containing those
statistics.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
In this code, 0 is returned on memory allocation failure, even though other
failures return -ENOMEM or other similar values.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
expression x,e1,e2,e3;
@@
ret = 0
... when != ret = e1
*x = \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != ret = e2
if (x == NULL) { ... when != ret = e3
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
To: Pat Gefre <pfg@sgi.com>
Cc: kernel-janitors@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1704/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently UBI erases all corrupted eraseblocks, irrespectively of the nature
of corruption: corruption due to power cuts and non-power cut corruption.
The former case is OK, but the latter is not, because UBI may destroy
potentially important data.
With this patch, during scanning, when UBI hits a PEB with corrupted VID
header, it checks whether this PEB contains only 0xFF data. If yes, it is
safe to erase this PEB and it is put to the 'erase' list. If not, this may
be important data and it is better to avoid erasing this PEB. Instead,
UBI puts it to the corr list and moves out of the pool of available PEB.
IOW, UBI preserves this PEB.
Such corrupted PEB lessen the amount of available PEBs. So the more of them
we accumulate, the less PEBs are available. The maximum amount of non-power
cut corrupted PEBs is 8.
This patch is a response to UBIFS problem where reporter
(Matthew L. Creech <mlcreech@gmail.com>) observes that UBIFS index points
to an unmapped LEB. The theory is that corresponding PEB somehow got
corrupted and UBI wiped it. This patch (actually a series of patches)
tries to make sure such PEBs are preserved - this would make it is easier
to analyze the corruption.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Start using the 'corr' list and add there PEBs which look truly corrupted,
which means they have corrupted VID header and the data which follows the
corrupted header does not contain all 0xFF bytes.
At the moment, this does not change UBI functionality much because these
PEBs will be erase when scanning finishes. But the plan is to teach UBI
preserving them.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Introduce a helper function to print hexdump: 'ubi_dbg_print_hex_dump()'.
It is compiled out if debugging is enabled. Will be used in the next patch.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch turns static function 'check_pattern()' into a non-static
'ubi_check_pattern()'. This is just a preparation for the chages which
are coming in the next patches.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Currently UBI maintains 2 lists of PEBs during scanning:
1. 'erase' list - PEBs which have no corruptions but should be erased
2. 'corr' list - PEBs which have some corruptions and should be erased
But we do not really need 2 lists for PEBs which should be erased after
scanning is done - this is redundant. So this patch makes sure all PEBs
which are corrupted are moved to the head of the 'erase' list. We add
them to the head to make sure they are erased first and we get rid of
corruption ASAP.
However, we do not remove the 'corr' list and realted functions, because
the plan is to use this list for other purposes. Namely, we plan to
put eraseblocks with corruption which does not look like it was caused
by unclean power cut. Then we'll preserve thes PEBs in order to avoid
killing potentially valuable user data.
This patch also amends PEBs accounting, because it was closely tight to
the 'erase'/'corr' lists separation.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch introduces 'add_corrupted()' function and separates out 'corr' list
manipulation from the common 'add_to_list()' function. This is just a
preparation for further changes - this patch does not change functionality.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
This patch improves readability and simplifies scanning code by changing a
long cascade of 'if' statements to a switch statement. This should presumably
be a little faster as well.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Rename local variable 'ec_corr' into 'ec_err' to make the code a little bit
more readable. 'ec_err' is more appropriate because it sounds more like 'error
when EC was read' and it looks more logical because we use it together with
'err'. Just a minor nicification which should improve the rather complex
scanning code.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Currently UBI has one small flaw - when we read EC or VID header, but find only
0xFF bytes, we return UBI_IO_FF and do not report whether we had bit-flips or
not. In case of the VID header, the scanning code adds this PEB to the free list,
even though there were bit-flips.
Imagine the following situation: we start writing VID header to a PEB and have a
power cut, so the PEB becomes unstable. When we scan and read the PEB, we get
a bit-flip. Currently, UBI would just ignore this and treat the PEB as free. This
patch changes UBI behavior and now UBI will schedule this PEB for erasure.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The 'UBI_IO_PEB_EMPTY' and 'UBI_IO_PEB_FREE' are essentially the same
and mean that there are only 0xFF bytes instead of headers. Simplify
UBI a little by turning them into a single 'UBI_IO_FF' error code.
Also, stop maintaining commentaries in 'ubi_io_read_vid_hdr()' which are
almost identical to commentaries in 'ubi_io_read_ec_hdr()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Rename UBI_IO_BAD_HDR_READ into UBI_IO_BAD_HDR_EBADMSG which is presumably more
self-documenting and readable. Indeed, the '_READ' suffix does not tell much and
even confuses, while '_EBADMSG' tells about uncorrectable ECC error, because we
use -EBADMSG all over the place to represent ECC errors.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Cleanup the Kconfig for UBI by using menuconfig to enable/disable the entire
driver. Remove the dependency checks for MTD_UBI and MTD_UBI_DEBUG by
wrapping the options in if/endif blocks and remove any redundant checks.
Remove all default n since that is the Kconfig default. Change menu "Additional
UBI debugging messages" into a comment to remove one menu level.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
The dabusb device driver is sufficiently serialized using
its own mutex, no need for the big kernel lock here
in addition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvb core only uses the big kernel lock in the open
and ioctl functions, which means it can be replaced with
a dvb specific mutex. Fortunately, all the ioctl functions
go through dvb_usercopy, so we can move the serialization
in there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
The bt8xx driver only uses the big kernel lock in its dst_ca_ioctl
function and never to serialize against other code, so we can
trivially replace it with a private mutex.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-media@vger.kernel.org
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
This driver already has a global mutex, so let's just
use that in the open function instead of the BKL.
It may not even be needed there, but this patch should
have the smallest impact.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Gross <mark.gross@intel.com>
RAW_SETBIND and RAW_GETBIND 32bit versions are fscked in interesting ways.
1) fs/compat_ioctl.c has COMPATIBLE_IOCTL(RAW_SETBIND) followed by
HANDLE_IOCTL(RAW_SETBIND, raw_ioctl). The latter is ignored.
2) on amd64 (and itanic) the damn thing is broken - we have int + u64 + u64
and layouts on i386 and amd64 are _not_ the same. raw_ioctl() would
work there, but it's never called due to (1). As it is, i386 /sbin/raw
definitely doesn't work on amd64 boxen.
3) switching to raw_ioctl() as is would *not* work on e.g. sparc64 and ppc64,
which would be rather sad, seeing that normal userland there is 32bit.
The thing is, slapping __packed on the struct in question does not DTRT -
it eliminates *all* padding. The real solution is to use compat_u64.
4) of course, all that stuff has no business being outside of raw.c in the
first place - there should be ->compat_ioctl() for /dev/rawctl instead of
messing with compat_ioctl.c.
[akpm@linux-foundation.org: coding-style fixes]
[arnd@arndb.de: port to 2.6.36]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
cciss: fix PCI IDs for new controllers
This patch fixes the botched up PCI IDs of new controllers. Please consider
this patch for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This patch reverts the driver to enabling/disabling the NFC interrupt
mask rather than enabling/disabling the system interrupt. This cleans
up the driver so that it doesn't rely on interrupts being disabled
within the interrupt handler.
For i.MX21 we keep the current behaviour, that is calling
enable_irq/disable_irq_nosync to enable/disable interrupts. This patch
is based on earlier work by John Ogness.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: John Ogness <john.ogness@linutronix.de>
Tested-by: John Ogness <john.ogness@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus/i2c/2636-rc8' of git://git.fluff.org/bjdooks/linux:
i2c-imx: do not allow interruptions when waiting for I2C to complete
i2c-davinci: Fix TX setup for more SoCs
448cd16 ("Input: evdev - rearrange ioctl handling") broke EVIOCSABS by
checking for the wrong direction bit.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Sven Neumann <s.neumann@raumfeld.com>
Tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds UART serial port support for S5P6450 SoC.
The S5P6450 has 6 UARTs, so adds resource of UART4 and UART5.
And to fix membase which is in serial/samsung.c is from Ben Dooks.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Some systems using this bus sometimes have very basic devices on them
such as regulators. So we need to be loaded even earlier in case the
devices are used by things such as early board init code. Therefore
register in subsys_initcall().
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Currently, if the bits_per_word when doing a transfer is not 8bits, we
always treat it as 16bits when we should actually be returning an error.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When the hardware is controlling the CS, there are some SPI options
we are unable to support. So issue a warning in the hopes that the
user will change to a SPI mode where we can support things sanely.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Using disable_irq() on the IRQ whose handler we are currently executing in
can easily lead to a hang. So use the nosync variant here.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
While combining things, also switch to the proper SPI bit define names.
This lets us punt the rarely used SPI defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
During runtime, the spi setup function may be called multiple times on the
same device in order to reconfigure some settings on the fly. When this
happens, we need to reset the ctl_reg bits so that changing the mode works
as expected.
Reported-by: Andy Getzendanner <james.getzendanner@students.olin.edu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This reduces duplication between the setup/transfer functions and keeps
values cached during setup from overriding values changed on a transfer
basis (like bits_per_word).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Using disable_irq() on the IRQ whose handler we are currently executing in
can easily lead to a hang. So use the nosync variant here.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Sometimes under load, the Blackfin core is able to send SPI register
updates out before the controller is actually disabled. So when we
go to reprogram the entire state (to switch to a different slave),
make sure we sync after disabling the controller.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We can't rely on the SPI_CTL/SPI_FLG registers retaining their state when
suspending, so save/restore their entire values.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The common SPI layers take care of detecting CS conflicts and preventing
two devices from claiming the same CS. This causes problems for the GPIO
CS support we currently have as we are using CS0 to mean "GPIO CS". But
if we have multiple devices using a GPIO CS, the common SPI layers see
multiple devices using the virtual "CS0" and reject any such attempts.
To make both work, we introduce an offset define. This represents the
max number of hardware CS values that the SPI peripheral supports. If
the CS is below this limit, we know we can use the hardware CS. If it's
above, we treat it as a GPIO CS. This keeps the CS unique as seen by
the common code and prevents conflicts.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The driver that we based ours on uses a little extra memory behind the
normal driver state, but we don't. So drop this useless bit of memory.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current structure names are a bit confusing as to what they represent,
so use better names.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than having to look up the same 3 sets of functions at the same
time, just use an ops structure so we only need to set one pointer.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
No point in creating our own version of true/false defines when there is
already a standard stdbool available to us.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The chip ops should always be initialized, so having null fallback
functions are useless.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
As David points out, the cs_change_per_word option isn't standard, nor is
anyone actually using it. So punt all of the dead code considering it
makes up ~10% of the code size.
Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The CS helper functions were toggling both the Flag Enable and the Flag
Value bits, but the Flag Value bit is ignored if the corresponding Flag
Enable bit is cleared. So under high speed transactions, the CS sometimes
would not toggle properly.
Since it makes no sense to toggle the Flag Enable bit dynamically when we
actually want to control the Flag Value, do this when setting up the device
and then only handle toggling of the CS value during runtime.
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current behavior in PIO mode is to poll the SPI status registers which
can obviously lead to higher latencies when doing a lot of SPI traffic.
There is a SPI interrupt which can be used instead to signal individual
completion of transactions.
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We should make sure the SPI controller is in a sane state in case the
boot loader left it in a crappy state. Such as DMA pending which causes
interrupts to fire on us.
When setting a sane initial state, do not default to slave mode. If we
do, then the SPI peripheral may implicitly take over the SPISS pin which
other things might be using.
For example, the BF533-STAMP uses this pin as a GPIO to control switching
between ethernet and flash. If the SPI peripheral controls the output
state instead, the ethernet is no longer accessible.
URL: http://blackfin.uclinux.org/gf/tracker/5630
Signed-off-by: Wolfgang Muees <wolfgang.mues@auerswald.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Anomaly 05000119 states that the DMA_RUN bit with peripherals isn't
reliable. However, the way the driver is currently written (DMA IRQ
callback), we don't need the polling in the first place, so drop it.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Re-order setup() a bit so we don't leak memory/dma/gpio resources upon
errors. Also make sure we don't call kfree() twice on the same object.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* Rename shpchp_wq to shpchp_ordered_wq and add non-ordered shpchp_wq
which is used instead of the system workqueue. This is to remove
the use of flush_scheduled_work() which is deprecated and scheduled
for removal.
* With cmwq in place, there's no point in creating workqueues lazily.
Create both shpchp_wq and shpchp_ordered_wq upfront.
* Include workqueue.h from shpchp.h.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* Rename pciehp_wq to pciehp_ordered_wq and add non-ordered pciehp_wq
which is used instead of the system workqueue. This is to remove
the use of flush_scheduled_work() which is deprecated and scheduled
for removal.
* With cmwq in place, there's no point in creating workqueues lazily.
Create both pciehp_wq and pciehp_ordered_wq upfront.
* Include workqueue.h from pciehp.h.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The i2c_imx_trx_complete() function is using
wait_event_interruptible_timeout() to wait for the I2C controller to
signal that it has completed an I2C bus operation. If the process that
causes the I2C operation receives a signal, the wait will be
interrupted, returning an error. It is better to let the I2C operation
finished before handling the signal (i.e. returning into userspace).
It is safe to use wait_event_timeout() instead, because the timeout
will allow the process to exit if the I2C bus hangs. It's also better
to allow the I2C operation to finish, because unacknowledged I2C
operations can cause the I2C bus to hang.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch is an improvement to 4bba0fd8d1
which got to mainline a little early.
Sudhakar Rajashekhara explains that at least OMAP-L138 requires MDR mode
settings before DXR for correct behaviour, so load MDR first with
STT cleared and later load again with STT set.
Tested on DM355 connected to Techwell TW2836 and Wolfson WM8985
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Tested-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Fixes cursor corruption in certain cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Revert commit 54672386cc
"firewire: ohci: fix up configuration of TI chips".
It caused massive slow-down and data corruption with a TSB82AA2 based
StarTech EC1394B2 ExpressCard and FireWire 800 harddisks.
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/657081http://thread.gmane.org/gmane.linux.kernel.firewire.user/4013
The fact that some card EEPROMs do not program these enhancements may be
related to TSB81BA3 phy chip errata, if not to bugs of TSB82AA2 itself.
We could re-add these configuration steps, but only conditional on a
whitelist of cards on which these enhancements bring a proven positive
effect.
Reported-and-tested-by: Eric Shattow <lucent@gmail.com>
Cc: Clemens Ladisch <clemens@ladisch.de>
Cc: <stable@kernel.org> 2.6.35
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
diva doesn't use workqueue and there is no reason to flush the system
workqueue from diva_os_remove_soft_isr(). Remove it.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Armin Schindler <armin@melware.de>
SoCs have a standard set of tuples consisting of frequency and
voltage pairs that the device will support per voltage domain. These
are called Operating Performance Points or OPPs. The actual
definitions of OPP varies over silicon versions. For a specific domain,
we can have a set of {frequency, voltage} pairs. As the kernel boots
and more information is available, a default set of these are activated
based on the precise nature of device. Further on operation, based on
conditions prevailing in the system (such as temperature), some OPP
availability may be temporarily controlled by the SoC frameworks.
To implement an OPP, some sort of power management support is necessary
hence this library depends on CONFIG_PM.
Contributions include:
Sanjeev Premi for the initial concept:
http://patchwork.kernel.org/patch/50998/
Kevin Hilman for converting original design to device-based.
Kevin Hilman and Paul Walmsey for cleaning up many of the function
abstractions, improvements and data structure handling.
Romit Dasgupta for using enums instead of opp pointers.
Thara Gopinath, Eduardo Valentin and Vishwanath BS for fixes and
cleanups.
Linus Walleij for recommending this layer be made generic for usage
in other architectures beyond OMAP and ARM.
Mark Brown, Andrew Morton, Rafael J. Wysocki, Paul E. McKenney for
valuable improvements.
Discussions and comments from:
http://marc.info/?l=linux-omap&m=126033945313269&w=2http://marc.info/?l=linux-omap&m=125482970102327&w=2http://marc.info/?t=125809247500002&r=1&w=2http://marc.info/?l=linux-omap&m=126025973426007&w=2http://marc.info/?t=128152609200064&r=1&w=2http://marc.info/?t=128468723000002&r=1&w=2
incorporated.
v1: http://marc.info/?t=128468723000002&r=1&w=2
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If the device which fails to resume is part of a loadable kernel module
it won't be checked at startup against the magic number stored in the
RTC.
Add a read-only sysfs attribute /sys/power/pm_trace_dev_match which
contains a list of newline separated devices (usually just the one)
which currently match the last magic number. This allows the device
which is failing to resume to be found after the modules are loaded
again.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Lock the PM device list mutex using device_pm_lock() and
device_pm_unlock() around the list iteration in show_dev_hash().
show_dev_hash() was reverse iterating dpm_list without first locking the
mutex that the functions in drivers/base/power/main.c lock. I assume
this was unintentional since there is no comment suggesting why the lock
might not be necessary.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If runtime suspend of a device fails returning -EAGAIN or -EBUSY,
which means that it's safe to try to suspend it again, the PM core
runs the runtime idle helper function for it. Unfortunately this may
lead to problems, for example for PCI devices whose drivers don't
implement the ->runtime_idle() callback, because in that case the
PCI bus type's ->runtime_idle() always calls pm_runtime_suspend()
for the given device. Then, if there's an automatic idle
notification after the driver's ->runtime_suspend() returning -EAGAIN
or -EBUSY, it will make the suspend happen again possibly causing a
busy loop to appear. To avoid that, remove the idle notification
after failing runtime suspend of a device altogether and let the
callers of pm_runtime_suspend() repeat the operation if need be.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reduce code duplication in rpm_idle(), rpm_suspend() and rpm_resume()
by using local pointers to store callback addresses and moving some
duplicated code into a separate function.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
This patch (as1427) implements the "autosuspend" facility for runtime
PM. A few new fields are added to the dev_pm_info structure and
several new PM helper functions are defined, for telling the PM core
whether or not a device uses autosuspend, for setting the autosuspend
delay, and for marking periods of device activity.
Drivers that do not want to use autosuspend can continue using the
same helper functions as before; their behavior will not change. In
addition, drivers supporting autosuspend can also call the old helper
functions to get the old behavior.
The details are all explained in Documentation/power/runtime_pm.txt
and Documentation/ABI/testing/sysfs-devices-power.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Some devices, such as USB interfaces, cannot be power-managed
independently of their parents, i.e., they cannot be put in low power
while the parent remains at full power. This patch (as1425) creates a
new "no_callbacks" flag, which tells the PM core not to invoke the
runtime-PM callback routines for the such devices but instead to
assume that the callbacks always succeed. In addition, the
non-debugging runtime-PM sysfs attributes for the devices are removed,
since they are pretty much meaningless.
The advantage of this scheme comes not so much from avoiding the
callbacks themselves, but rather from the fact that without the need
for a process context in which to run the callbacks, more work can be
done in interrupt context.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1424) combines the various public entry points for the
runtime PM routines into three simple functions: one for idle, one for
suspend, and one for resume. A new bitflag specifies whether or not
to increment or decrement the usage_count field.
The new entry points are named __pm_runtime_idle,
__pm_runtime_suspend, and __pm_runtime_resume, to reflect that they
are trampolines. Simultaneously, the corresponding internal routines
are renamed to rpm_idle, rpm_suspend, and rpm_resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1423) merges the asynchronous routines
__pm_request_idle(), __pm_request_suspend(), and __pm_request_resume()
with their synchronous counterparts. The RPM_ASYNC bitflag argument
serves to indicate what sort of operation to perform.
In the course of performing this merger, it became apparent that the
various functions don't all behave consistenly with regard to error
reporting and cancellation of outstanding requests. A new routine,
rpm_check_suspend_allowed(), was written to centralize much of the
testing, and the other functions were revised to follow a simple
algorithm:
If the operation is disallowed because of the device's
settings or current state, return an error.
Cancel pending or scheduled requests of lower priority.
Schedule, queue, or perform the desired operation.
A few special cases and exceptions are noted in comments.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The "from_wq" argument in __pm_runtime_suspend() and
__pm_runtime_resume() supposedly indicates whether or not the function
was called by the PM workqueue thread, but in fact it isn't always
used this way. It really indicates whether or not the function should
return early if the requested operation is already in progress.
Along with this badly-named boolean argument, later patches in this
series will add several other boolean arguments to these functions and
others. Therefore this patch (as1422) begins the conversion process
by replacing from_wq with a bitflag argument. The same bitflags are
also used in __pm_runtime_get() and __pm_runtime_put(), where they
indicate whether or not the operation should be asynchronous.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1421) moves the PM runtime accounting subroutines up to
the beginning of runtime.c, taking them out of the middle of the
functions that do the actual work. No operational changes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
There is a potential issue with the asynchronous suspend code that
a device driver suspending asynchronously may not notice that it
should back off. There are two failing scenarions, (1) when the
driver is waiting for a driver suspending synchronously to complete
and that second driver returns error code, in which case async_error
won't be set and the waiting driver will continue suspending and (2)
after the driver has called device_pm_wait_for_dev() and the waited
for driver returns error code, in which case the caller of
device_pm_wait_for_dev() will not know that there was an error and
will continue suspending.
To fix this issue make __device_suspend() set async_error, so
async_suspend() doesn't need to set it any more, and make
device_pm_wait_for_dev() return async_error, so that its callers
can check whether or not they should continue suspending.
No more changes are necessary, since device_pm_wait_for_dev() is
not used by any drivers' suspend routines.
Reported-by: Colin Cross <ccross@android.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce struct wakeup_source for representing system wakeup sources
within the kernel and for collecting statistics related to them.
Make the recently introduced helper functions pm_wakeup_event(),
pm_stay_awake() and pm_relax() use struct wakeup_source objects
internally, so that wakeup statistics associated with wakeup devices
can be collected and reported in a consistent way (the definition of
pm_relax() is changed, which is harmless, because this function is
not called directly by anyone yet). Introduce new wakeup-related
sysfs device attributes in /sys/devices/.../power for reporting the
device wakeup statistics.
Change the global wakeup events counters event_count and
events_in_progress into atomic variables, so that it is not necessary
to acquire a global spinlock in pm_wakeup_event(), pm_stay_awake()
and pm_relax(), which should allow us to avoid lock contention in
these functions on SMP systems with many wakeup devices.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Seen on MIPS32, gcc 4.4.3, 2.6.36-rc4:
drivers/base/power/main.c: In function 'dpm_show_time':
drivers/base/power/main.c:415: warning: comparison of distinct pointer types lacks a cast
do_div() takes unsigned parameters:
uint32_t do_div(uint64_t *n, uint32_t base);
Using an unsigned variable for usecs64 should not cause any problems,
because calltime >= starttime .
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Allow drivers, that belong to subsystems which use the generic
runtime pm callbacks, not to define runtime pm suspend/resume handlers,
by implicitly assuming success in such cases.
This is needed to eliminate nop handlers that would otherwise be
necessary by drivers which enable runtime pm, but don't need
to do anything when their devices are runtime-suspended/resumed.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
au100_generic and soc_common call flush_scheduled_work() spuriously.
Remove them.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
serial_cs doesn't use the system workqueue. Drop spurious
flush_scheduled_work() call.
This is to prepare for the deprecation and removal of
flush_scheduled_work().
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patches a typo in the debug message.
Signed-off-by: Matthias Brugger <mensch0815@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The compat code for the VIDIOCSMICROCODE ioctl is totally buggered.
It's only used by the VIDEO_STRADIS driver, and that one is scheduled to
staging and eventually removed unless somebody steps up to maintain it
(at which point it should use request_firmware() rather than some magic
ioctl). So we'll get rid of it eventually.
But in the meantime, the compatibility ioctl code is broken, and this
tries to get it to at least limp along (even if Mauro suggested just
deleting it entirely, which may be the right thing to do - I don't think
the compatibility translation code has ever worked unless you were very
lucky).
Reported-by: Kees Cook <kees.cook@canonical.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix SDIO suspend/resume regression introduced by 4c2ef25fe0 "mmc: fix
all hangs related to mmc/sd card insert/removal during suspend/resume":
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.01 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.01 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
pm_op(): platform_pm_suspend+0x0/0x5c returns -38
PM: Device pxa2xx-mci.0 failed to suspend: error -38
PM: Some devices failed to suspend
4c2ef25fe0 moved the card removal/insertion mechanism out of MMC's
suspend/resume path and into pm notifiers (mmc_pm_notify), and that
broke SDIO's expectation that mmc_suspend_host() will remove the card,
and squash the error, in case -ENOSYS is returned from the bus suspend
handler (mmc_sdio_suspend() in this case).
mmc_sdio_suspend() is using this whenever at least one of the card's SDIO
function drivers does not have suspend/resume handlers - in that case
it is agreed to force removal of the entire card.
This patch fixes this regression by trivially bringing back that part of
mmc_suspend_host(), which was removed by 4c2ef25fe0.
Reported-and-tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: <stable@kernel.org>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add Cando touch screen 15.6-inch product id
HID: Add MULTI_INPUT quirk for turbox/mosart touchscreen
HID: hidraw, fix a NULL pointer dereference in hidraw_write
HID: hidraw, fix a NULL pointer dereference in hidraw_ioctl
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.
The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.
New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time. Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.
The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.
Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.
Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.
===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
// but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}
@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}
@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}
@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
*off = E
|
*off += E
|
func(..., off, ...)
|
E = *off
)
...+>
}
@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}
@ fops0 @
identifier fops;
@@
struct file_operations fops = {
...
};
@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
.llseek = llseek_f,
...
};
@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
.read = read_f,
...
};
@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
.write = write_f,
...
};
@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
.open = open_f,
...
};
// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
... .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};
@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
... .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};
// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
... .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};
// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};
// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};
@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+ .llseek = default_llseek, /* write accesses f_pos */
};
// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////
@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
.write = write_f,
.read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};
@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};
@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};
@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Previously we tracked whether the integrity metadata had been remapped
using a request flag. This was fine for low-level retries. However, if
an I/O was redriven by upper layers we would end up remapping again,
causing the retry to fail.
Deprecate the REQ_INTEGRITY flag and introduce BIO_MAPPED_INTEGRITY
which enables filesystems to notify lower layers that the bio in
question has already been remapped.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Some cards need the speedups on, some need them off. As we can't detect
this reliably, at least give the users a hint how to tweak the system.
Reported-by: David Bluecame <david.bluecame@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This adds a necessary race breaker to these commits:
drbd: fix for possible deadlock on IO error during resync
drbd: drop wrong debug asserts, fix recently introduced race
What we do is get a refcount, check the state, then depending on the
state and the requested minimum disk state, either hold it (success),
or give it back immediately (failed "try lock").
Some code paths (flushing of drbd metadata) may still grab and hold a
refcount even if we are D_FAILED (application IO won't).
So even if we hit local_cnt == 0 once after being D_FAILED,
we still need to wait for that again after we changed to D_DISKLESS.
Once local_cnt reaches 0 while we are D_DISKLESS, we can be sure that
no one will look at the protected members anymore, so only then is it
safe to free them.
We cannot easily convert to standard locking primitives here, as we want
to be able to use it in atomic context (we always do a "try lock"),
as well as hold references for a "long time" (from IO submission to
completion callback).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Commit e9677b3ce (oprofile, ARM: Use oprofile_arch_exit() to
cleanup on failure) caused oprofile_perf_exit to be called
in the cleanup path of oprofile_perf_init. The __exit tag
for oprofile_perf_exit should therefore be dropped.
The same has to be done for exit_driverfs as well, as this
function is called from oprofile_perf_exit. Else, we get
the following two linker errors.
LD .tmp_vmlinux1
`oprofile_perf_exit' referenced in section `.init.text' of arch/arm/oprofile/built-in.o: defined in discarded section `.exit.text' of arch/arm/oprofile/built-in.o
make: *** [.tmp_vmlinux1] Error 1
LD .tmp_vmlinux1
`exit_driverfs' referenced in section `.text' of arch/arm/oprofile/built-in.o: defined in discarded section `.exit.text' of arch/arm/oprofile/built-in.o
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
oprofile_perf.c needs to include platform_device.h
Otherwise we get the following build break.
CC arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.o
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:192: warning: 'struct platform_device' declared inside parameter list
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:192: warning: its scope is only this definition or declaration, which is probably not what you want
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:201: warning: 'struct platform_device' declared inside parameter list
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:210: error: variable 'oprofile_driver' has initializer but incomplete type
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:211: error: unknown field 'driver' specified in initializer
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:211: error: extra brace group at end of initializer
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:211: error: (near initialization for 'oprofile_driver')
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:213: warning: excess elements in struct initializer
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:213: warning: (near initialization for 'oprofile_driver')
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:214: error: unknown field 'resume' specified in initializer
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:214: warning: excess elements in struct initializer
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:214: warning: (near initialization for 'oprofile_driver')
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:215: error: unknown field 'suspend' specified in initializer
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:215: warning: excess elements in struct initializer
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c:215: warning: (near initialization for 'oprofile_driver')
arch/arm/oprofile/../../../drivers/oprofile/oprofile_perf.c: In function 'init_driverfs':
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
ehea: Fix a checksum issue on the receive path
net: allow FEC driver to use fixed PHY support
tg3: restore rx_dropped accounting
b44: fix carrier detection on bind
net: clear heap allocations for privileged ethtool actions
NET: wimax, fix use after free
ATM: iphase, remove sleep-inside-atomic
ATM: mpc, fix use after free
ATM: solos-pci, remove use after free
net/fec: carrier off initially to avoid root mount failure
r8169: use device model DMA API
r8169: allocate with GFP_KERNEL flag when able to sleep
dt is unsigned so it's never less than zero. We are calculating the
elapsed time, and that's never less than zero (unless there is a bug or
we invent time travel). The comparison here is just to guard against
divide by zero bugs.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Consolidate the ifdef's for the debug level, accidentally the used both
DEBUG and DRBD_DEBUG_MD_SYNC. Default to off.
For production, we can safely reduce the grace period for this timer
again the the value we used to have.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
It sometimes may take a while for the after state change work to be
scheduled, which does drbd_md_sync. At convenient places, we should do
explicit drbd_md_sync to have the new state information on disk as soon
as possible.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
commit 2372c38caadeaebc68a5ee190782c2a0df01edc3
drbd: fix for possible deadlock on IO error during resync
introduced a new ASSERT, which turns out to be wrong. Drop it.
Also serialize the state change to D_DISKLESS with the after state
change work of the -> D_FAILED transition, don't open a new race.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
As we usually update the generation UUIDs here, we should explicitly
sync them to disk. So far this has been done only implicitly by related
code paths.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This might happen if on the VERIFY_S node the disk gets dropped.
Although this is an cluster wide state transition, the VERIFY_T node,
updates it connection state first. Then the ack packet for the
cluster wide state transition travels back, and the VERIFY_S node
stops to produce the P_OV_REQUEST packets.
There is absolutely nothing wrong with that.
Further, do not log "Can not satisfy peer's..." on the VERIFY_S
node in this case, but pretend that they had equal checksum.
[Bugz 327]
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Scenario:
Something (say, flush-147:0) is in drbd_al_begin_io,
holding a local_cnt, waiting for the resync to make progress.
Disk fails, worker in after_state_ch does drbd_rs_cancel_all,
then waits for local_cnt to drop to zero.
flush-147:0 is woken by drbd_rs_cancel_all, needs to write an AL
transaction, and queues that on the worker.
Deadlock.
Fix: do not wait in the worker, have put_ldev() trigger the
state change D_FAILED -> D_DISKLESS when necessary.
put_ldev() cannot do the state change directly, as it may or may not
already hold various spinlocks. We queue a short work instead.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Various cleanup paths have been incomplete, for the very unlikely case
that we cannot allocate enough bios from process context when submitting
on behalf of the peer or resync process.
Never observed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If it was an "empty" resync, the SyncSource may have already "finished"
the resync and rotated the UUIDs, before noticing the connection loss
(and generating a new uuid, if Primary, rotating again), while the
SyncTarget did not change its uuids at all, or only got to the previous
sync-uuid.
This would then again lead to a full sync on next handshake
(see also Bug #251).
Fix:
Use explicit resync finished notification even for empty resyncs,
do not finish an empty resync implicitly on the SyncSource.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Preparation patch so more drbd_send_state() usage on the peer
will not confuse drbd in receive_state().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
no functional change, just using full state instead of just the .conn
part of it for comparisons.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd commit 17c854fea474a5eb3cfa12e4fb019e46debbc4ec
drbd: receiving of big packets, for payloads between 64kByte and 4GByte
introduced a new on-the-wire packet header format. We must no longer
assume either format, but use the result of whatever drbd_recv_header
has decoded.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We used to be16_to_cpu the length field in our received packet header.
drbd commit 17c854fea474a5eb3cfa12e4fb019e46debbc4ec
drbd: receiving of big packets, for payloads between 64kByte and 4GByte
changed this, but forgot to adjust a few places where we relied on
h->length being in native byte order.
This broke the receiving side of the RLE compressed bitmap exchange.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This caused rs_planed to be not in sync with the content of the fifo.
That in turn could cause that the resync comes to a complete halt.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Connections through a compressing proxy might have more bits
on the fly. 500MByte instead of 50MByte
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we release the page pointed to by md_io_tmpp, we need to zero out the
pointer, too, as that may be used later to decide whether we need to
allocate a new page again.
Impact: a previously freed page may be used and clobbered. Depending on
what that particular page is being used for meanwhile, this may result
in silent data corruption of completely unrelated things.
Only of concern on devices with logical_block_size != 512 byte,
if you re-attach after becoming diskless once.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Two missing corner cases to the "maximum packet size" handshake.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There are three ways to get IO suspended:
* Loss of any access to data
* Fence-peer-handler running
* User requested to suspend IO
Track those in different bits, so that one condition clearing its
state bit does not interfere with the other two conditions.
Only when the user resumes IO he overrules all three bits.
The fact is hidden from the user, he sees only a single suspend
bit.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Forgot to consider the max size for the resync requests.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a synctarget lost connection while being WFSyncUUID,
due to "state sanitizing", the attempted state change to SyncTarget
looked like an "invalidate" to after_state_ch() later,
thus caused a full sync on next handshake (Bug #318).
drbd0: PingAck did not arrive in time.
drbd0: peer( Primary -> Unknown ) conn( WFSyncUUID -> NetworkFailure ) pdsk( UpToDate -> DUnknown )
from : { cs:NetworkFailure ro:Secondary/Unknown ds:UpToDate/DUnknown r--- }
to : { cs:SyncTarget ro:Secondary/Unknown ds:Inconsistent/DUnknown r--- }
after sanizising, resulted in
state: { cs:NetworkFailure ro:Secondary/Unknown ds:Inconsistent/DUnknown r--- }
drbd0: disk( UpToDate -> Inconsistent )
Fix:
don't mask state transition errors in "sanitizing",
so the requested state change to SyncTarget fails,
instead of being implicitly "remaped" to invalidate.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we cannot satisfy a request (because our disk just broke),
we still need to drain the payload. Or we'll get a protocol error
when interpreting the payload as DRBD packet header.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
BUG trace would look like:
lc_find
drbd_rs_complete_io
got_OVResult
drbd_asender
Could be triggered by explicit, or IO-error policy based,
detach during online-verify.
We may only dereference mdev->resync, if we first get_ldev(), as the
disk may break any time, causing mdev->resync to disappear once all
ldev references have been returned.
Already in flight online-verify requests or replies may still come in,
which we then need to ignore.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Just in case we have some pending meta data changes to sync, do it
before we call our userland helper, as that may take some time,
or even cause a hard reboot.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
addendum to baa33ae4eaa4477b60af7c434c0ddd1d182c1ae7
The race:
drbd_md_sync()
if (!test_and_clear_bit(MD_DIRTY, &mdev->flags))
return;
==> RACE with drbd_md_mark_dirty() rearming the timer.
del_timer(&mdev->md_sync_timer);
Fixed by moving the del_timer before the test_and_clear_bit.
Additionally only rearm the timer in drbd_md_mark_dirty, if MD_DIRTY was
not already set, reduce the grace period from five to one second, and
add an ifdef'ed debuging aid to find code paths missing an explicit
drbd_md_sync, if any, as those are the only relevant ones for this race.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The actual race happened int the drbd_start_resync() function. Where
drbd_resync_finished() -> __drbd_set_state() set STOP_SYNC_TIMER and
armed the timer.
If the timer fired before execution reaches the mod_timer statement
at the end of drbd_start_resync() the latter would cause an
unexpected call to w_make_resync_request().
Removed the STOP_SYNC_TIMER bit, and base it on the connection state.
The STOP_SYNC_TIMER bit probably originates probably the time before
the state engine.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If pacemaker (for example) decided to initialize minor devices not in
the exact sync-after dependency order, the configuration partially
failed with an error "The sync-after minor number is invalid". (Bugz. #322)
We can avoid that by implicitly creating unconfigured minor devices,
if others depend on them.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a drbd_nl_net_conf hits the small window between the state change
to C_STANDALONE and the corresponding cleanup in after_state_ch,
that cleanup would throw away stuff we now need again,
and later trigger BUG_ON()s.
Fixed by properly serializing the new config request with
any pending cleanup.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When the complete device is marked as out of sync, we can disable
updates of the on disk AL. Currently AL updates are only disabled
if one uses the "invalidate-remote" command on an unconnected,
primary device, or when at attach time all bits in the bitmap are
set.
As of now, AL updated do not get disabled when a all bits becomes
set due to application writes to an unconnected DRBD device.
While this is a missing feature, it is not considered important,
and might get added later.
BTW, after initializing a "one legged" DRBD device
drbdadm create-md resX
drbdadm -- --force primary resX
AL updates also get disabled, until the first connect.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now we have multiple BIOs per ee, packets with a 32 bit length field,
it gets time to use these goodies.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we intent to use the block_id member of an epoch entry,
we may not use the digest member.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We now track the data rate of locally submitted resync related requests,
and can thus detect non-resync activity on the lower level device.
If the current sync rate is above c-min-rate, and the lower level device
appears to be busy, we throttle the resyncer.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
also canonicalize the return values of read_for_csum
and drbd_rs_begin_io to return -ESOMETHING, or 0 for success.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The current resync speed as displayed in /proc/drbd fluctuates a lot.
Using an array of rolling marks makes this calculation much more stable.
We used to have this (a long time ago with 0.7), but it got lost somehow.
If "stalled", do not discard the rest of the information, just add a
" (stalled)" tag to the progress line.
This patch also shortens a spinlock critical section somewhat, and
reduces the number of atomic operations in put_ldev.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The commit 288f422ec1
drbd: Track all IO requests on the TL, not writes only
moved a list_add_tail(req, ) into a region where req
may have just been freed due to conflict detection.
Fix this by adding a proper cleanup section for that code path.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We get the following when building on ppc64 due to lack of include of
<asm/io.h>:
In file included from drivers/spi/spi_fsl_espi.c:25:0:
drivers/spi/spi_fsl_lib.h: In function 'mpc8xxx_spi_write_reg':
drivers/spi/spi_fsl_lib.h:88:2: error: implicit declaration of function 'out_be32'
drivers/spi/spi_fsl_lib.h: In function 'mpc8xxx_spi_read_reg':
drivers/spi/spi_fsl_lib.h:93:2: error: implicit declaration of function 'in_be32'
drivers/spi/spi_fsl_espi.c: In function 'fsl_espi_remove':
drivers/spi/spi_fsl_espi.c:571:2: error: implicit declaration of function 'iounmap'
drivers/spi/spi_fsl_espi.c: In function 'fsl_espi_probe':
drivers/spi/spi_fsl_espi.c:602:2: error: implicit declaration of function 'ioremap'
drivers/spi/spi_fsl_espi.c:602:24: warning: assignment makes pointer from integer without a cast
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We may not free tl_hash when IO is suspended, since we can not wait
until ap_bio_cnt reaches zero.
We can do this after susp reched 0, since then tl_clear was called
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
After disconnect (most likely mdev->net_cnt == 0) and we are
still in an unstable state (!drbd_state_is_stable()). When we
get an IO request in drbd_get_max_buffers() (called from
__inc_ap_bio_cond(), called from inc_ap_bio()) we wake up
misc_wait. Misc_wait is also used in inc_ap_bio() to sleep
until the outcome of __inc_ap_bio_cond() changes. => Busy loop!
Solution: Have a dedicated wait queue for get_net_conf() and
put_net_conf().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Make sure the state engine can deny two primaries to connect
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When a fencing policy of "resource-and-stonith" is configured,
and DRBD looses connection to it's peer, we can delay the
creation of a new current-UUID until IO gets thawed.
That allows one to deploy fence-peer handlers that actually
commit suicide on the machine they get started.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since we can not thaw the transfer log, the next logical step is
to allow reconnects while the fence-peer handler runs.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
State transitions in the space of non-allowed states used
to be very noisy. Reduce that, since that has little value
for the majority of the user base.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When no data is accessible (no connection to the peer, nor a local disk)
allow the user to select to freeze all IO operations instead of getting
IO errors.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If IO was frozen for a temporal network outage, resend the
content of the transfer-log into the newly established connection.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With that the drbd_fail_pending_reads() function becomes obsolete.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
pcmcia_socket_dev_resume() is only referenced from macro
SET_SYSTEM_SLEEP_PM_OPS(NULL, pcmcia_socket_dev_resume)
which based on CONFIG_PM_SLEEP may or may not actually
use its second parameter.
Signed-off-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The PowerPC Book-E watchdog driver (booke_wdt.c) defines a default timeout
value in the code based on whether it's a Freescale Book-E part of not.
Instead of having hard-coded values in the driver, make it a Kconfig
option.
As newer chips gets faster, the current default values become less
appropriate, since the timeout sometimes occurs before the kernel finishes
booting. Making the value a Kconfig option allows BSPs to configure a new
value without requiring the wdt_period command-line parameter to be set.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Register the __init and __exit functions in the PowerPC Book-E Watchdog
driver as module entry/exit functions, and modify the Kconfig entry.
Add a .release method for the PowerPC Book-E Watchdog driver, so that the
watchdog is disabled when the driver is closed.
Loosely based on original code from Jiang Yutang <b14898@freescale.com>.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
bits_per_word option in spi_transfer are allowed if it does not change
the csr register.
This is necessary for the driver in
drivers/staging/iio/adis16260_core.c, as it uses this option.
Signed-off-by: Matthias Brugger <mensch0815@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch fixes the following build error introduced by commit
65308c46, "spi/topcliff: cleanup for style and conciseness".
drivers/spi/spi_topcliff_pch.c: In function 'pch_spi_process_messages':
drivers/spi/spi_topcliff_pch.c:752: warning: 'data' is used uninitialized in
+this function
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Silent spurious error message
drm/radeon/kms: fix bad cast/shift in evergreen.c
drm/radeon/kms: make TV/DFP table info less verbose
drm/radeon/kms: leave certain CP int bits enabled
drm/radeon/kms: avoid corner case issue with unmappable vram V2
Commit 0793448 "DMAENGINE: generic channel status v2" changed the interface for
how dma channel progress is retrieved. It inadvertently exported an internal
helper function ioat_tx_status() instead of ioat_dma_tx_status(). The latter
polls the hardware to get the latest completion state, while the helper just
evaluates the current state without touching hardware. The effect is that we
end up waiting for completion timeouts or descriptor allocation errors before
the completion state is updated.
iperf (before fix):
[SUM] 0.0-41.3 sec 364 MBytes 73.9 Mbits/sec
iperf (after fix):
[SUM] 0.0- 4.5 sec 499 MBytes 940 Mbits/sec
This is a regression starting with 2.6.35.
Cc: <stable@kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Maciej Sosnowski <maciej.sosnowski@intel.com>
Reported-by: Richard Scobie <richard@sauce.co.nz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Currently we set all skbs with CHECKSUM_UNNECESSARY, even
those whose protocol we don't know. This patch just
add the CHECKSUM_COMPLETE tag for non TCP/UDP packets.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least one board using the FEC driver does not have a conventional
PHY attached to it, it is directly connected to a somewhat simple
ethernet switch (the board is the SnapGear/LITE, and the attached
4-port ethernet switch is a RealTek RTL8305). This switch does not
present the usual register interface of a PHY, it presents nothing.
So a PHY scan will find nothing - it finds ID's of 0 for each PHY
on the attached MII bus.
After the FEC driver was changed to use phylib for supporting PHYs
it no longer works on this particular board/switch setup.
Add code support to use a fixed phy if no PHY is found on the MII bus.
This is based on the way the cpmac.c driver solved this same problem.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This add the product id of the touch screen found on ACER Aspire 5738PZ. Works
with hid-cando driver.
Signed-off-by: Francois Jaouen<francois.jaouen@laposte.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The function has an unsigned return type, but returns a negative constant
to indicate an error condition. The result of calling the function is
always stored in a variable of type (signed) int, and thus unsigned can be
dropped from the return type.
A sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@exists@
identifier f;
constant C;
@@
unsigned f(...)
{ <+...
* return -C;
...+> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add eSPI controller support based on the library code spi_fsl_lib.c.
The eSPI controller is newer controller 85xx/Pxxx devices supported.
There're some differences comparing to the SPI controller:
1. Has different register map and different bit definition
So leave the code operated the register to the driver code, not
the common code.
2. Support 4 dedicated chip selects
The software can't controll the chip selects directly, The SPCOM[CS]
field is used to select which chip selects is used, and the
SPCOM[TRANLEN] field is set to tell the controller how long the CS
signal need to be asserted. So the driver doesn't need the chipselect
related function when transfering data, just set corresponding register
fields to controll the chipseclect.
3. Different Transmit/Receive FIFO access register behavior
For SPI controller, the Tx/Rx FIFO access register can hold only
one character regardless of the character length, but for eSPI
controller, the register can hold 4 or 2 characters according to
the character lengths. Access the Tx/Rx FIFO access register of the
eSPI controller will shift out/in 4/2 characters one time. For SPI
subsystem, the command and data are put into different transfers, so
we need to combine all the transfers to one transfer in order to pass
the transfer to eSPI controller.
4. The max transaction length limitation
The max transaction length one time is limitted by the SPCOM[TRANSLEN]
field which is 0xFFFF. When used mkfs.ext2 command to create ext2
filesystem on the flash, the read length will exceed the max value of
the SPCOM[TRANSLEN] field.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Refactor the common code in file spi_fsl_spi.c to spi_fsl_lib.c used
by SPI/eSPI controller driver as a library, and leave the QE/CPM SPI
controller code in the SPI controller driver spi_fsl_spi.c.
Because the register map of the SPI controller and eSPI controller
is so different, also leave the code operated the register to the
driver code, not the common code.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This will pave the way to refactor out the common code which can be used
by the eSPI controller driver, and rename the SPI controller dirver to the
file spi_fsl_spi.c.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This removes some dubious allocation of a local chipinfo struct
in favor of a constant preset, tagging that one const revealed
further problems with platform data being modified so fixed up
these too.
Reported-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
What is the dev pointer doing inside the platform data anyway.
We have another pointer to the actual device at hand, use that.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds spi->mode support for the AMBA pl022 driver and
allows spidev to correctly alter SPI modes. Unused fields used in
the pl022 header file for the pl022_config_chip have been removed.
The ab8500 client driver selects the data transfer size instead
of the platform data.
For platforms that use the amba pl022 driver, the unused fields
in the controller data structure have been removed and the .mode
field in the SPI board info structure is used instead.
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Tested-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This extends the PL022 SSP/SPI driver with generic DMA engine
support using the PrimeCell DMA engine interface. Also fix up the
test code for the U300 platform.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch makes multiple cleanups to the new topcliff pch spi driver
including, but not limited to,
- removing superfluous brackets around variables
- open coding functions that are only used once
- removing unnecessary line breaks
- removing unused functions
- simplifying the interrupt enable/disable code
- remove unnecessary (void *) casts.
- remove b_mem_fail from pch_spi_set_tx to code it more cleanly
- shorten dev_dbg() messages for conciseness and readability
More cleanups are still needed in this driver. In particular,
- the driver filename should be changed to spi_topcliff_pch.c
- many of the dev_dbg() lines should be trimmed (particularly the ones
on unconditional code paths).
- I suspect that the locking model not correct. I'd like to know what
drivers' critical regions are, and how they are protected.
- get_resources and release_resources probably should be open coded in
.probe and .release respectively.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
