Both Hauppauge WinTV 44981 (bt878) and the HVR 1110 (saa7134) have a Zilog
Z8F0811. The transmitter was not probed. Receive and transmit tested on
both cards.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The iMON PAD controller has a analog stick, which can be switched to
keyboard mode (cursor keys) or work as a crappy mouse.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The raw_register function exists to create input devices associated with
that IR protocol.
If the mce_kbd module is loaded, then every rc device will have mce_kbd
input devices, even if the protocol is not enabled. Change this to call
the register function to when the protocol is enabled.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Some VSP instances have two blending units named BRU (Blend/ROP Unit)
and BRS (Blend/ROP Sub unit). The BRS is a smaller version of the BRU
with only two inputs, but otherwise offers similar features and offers
the same register interface. The BRU and BRS can be used exchangeably in
VSP pipelines (provided no more than two inputs are needed).
Due to historical reasons, the VSP1 driver implements support for both
the BRU and BRS through objects named vsp1_bru. The code uses the name
BRU to refer to either the BRU or the BRS, except in a few places where
noted explicitly. This creates confusion.
In an effort to avoid confusion, rename the vsp1_bru object and the
corresponding API to vsp1_brx, and use BRx to refer to blend unit
instances regardless of their type. The names BRU and BRS are retained
where reference to a particular blend unit type is needed, as well as in
hardware registers to stay close to the datasheet.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Dynamic assignment of the BRU and BRS to pipelines is prone to
regressions, add messages to make debugging easier. Keep it as a
separate commit to ease removal of those messages once the code will
deem to be completely stable.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The VSPDL variant drives two DU channels through two LIF and two
blenders, BRU and BRS. The DU channels thus share the five available
VSPDL inputs and expose them as five KMS planes.
The current implementation assigns the BRS to the second LIF and thus
artificially limits the number of planes for the second display channel
to two at most.
Lift this artificial limitation by assigning the BRU and BRS to the
display pipelines on demand based on the number of planes used by each
pipeline. When a display pipeline needs more than two inputs and the BRU
is already in use by the other pipeline, this requires reconfiguring the
other pipeline to free the BRU before processing, which can result in
frame drop on both pipelines.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
When disabling a DRM plane, the corresponding RPF is only marked as
removed from the pipeline in the atomic update handler, with the actual
removal happening when configuring the pipeline at atomic commit time.
This is required as the RPF has to be disabled in the hardware, which
can't be done from the atomic update handler.
The current implementation is RPF-specific. Make it independent of the
entity type by using the entity's pipe pointer to mark removal from the
pipeline. This will allow using the mechanism to remove BRU instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Display list completion is already reported to the frame end handler,
but that mechanism is global to all display lists. In order to implement
BRU and BRS reassignment in DRM pipelines we will need to commit a
display list and wait for its completion internally, without reporting
it to the DRM driver. Extend the display list API to support such an
internal use of the display list.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
We will soon need to return more than a boolean completion status from
the vsp1_dlm_irq_frame_end() IRQ handler. Turn the return value into a
bitfield to prepare for that. No functional change is introduced here.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In order to make the vsp1_du_setup_lif() easier to read, and for
symmetry with the DRM pipeline input setup, move the pipeline output
setup code to a separate function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vsp1_du_setup_lif() function sets up the DRM pipeline input
manually. This duplicates the code from the
vsp1_du_pipeline_setup_inputs() function. Replace the manual
implementation by a call to the function.
As the pipeline has no enabled input in vsp1_du_setup_lif(), the
vsp1_du_pipeline_setup_inputs() function will not setup any RPF, and
will thus not setup formats on the BRU sink pads. This isn't a problem
as all inputs are disabled, and the BRU sink pads will be reconfigured
from the atomic commit handler when inputs will be enabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
To implement fully dynamic plane assignment to pipelines, we need to
reassign the BRU and BRS to the DRM pipelines in the atomic commit
handler. In preparation for this setup factor out the BRU source pad
code and call it both at LIF setup and atomic commit time.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The DRM pipeline setup code used at atomic commit time is similar to the
setup code used when enabling the pipeline. Move it to a separate
function in order to share it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Move the duplicated DRM pipeline configuration code to a function and
call it from vsp1_du_setup_lif() and vsp1_du_atomic_flush().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The DRM pipeline handling code uses the entity's pipe list head to check
whether the entity is already included in a pipeline. This method is a
bit fragile in the sense that it uses list_empty() on a list_head that
is a list member. Replace it by a simpler check for the entity pipe
pointer.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Various types of objects subclassing vsp1_entity currently store a
pointer to the pipeline. Move the pointer to vsp1_entity to simplify the
code and avoid storing the pipeline in more entity subclasses later.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The vsp1_drm_pipeline enabled field is set but never used. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The DRM support code manages a pipeline of VSP entities, each backed by
a media entity. When starting or stopping the pipeline, it starts and
stops the media pipeline through the media API in order to store the
pipeline pointer in every entity.
The driver doesn't use the pipe pointer in media entities, neither does
it rely on the other effects of the media_pipeline_start() and
media_pipeline_stop() functions. Furthermore, as the media links for the
DRM pipeline are never set up correctly, and as the pipeline can be
modified dynamically when enabling or disabling planes, the current
implementation is not correct. Remove the incorrect and unneeded code.
While at it remove the outdated comment that states that entities are
not started when the LIF is setup, as they now are.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the USBTV_TV_STD define instead of repeating ourselves.
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Depending on the chosen standard, configure the decoder to use the
appropriate color encoding standard (PAL-like, NTSC-like or SECAM).
Until now, the decoder was not configured for a specific color standard,
making it autodetect the color encoding.
While this may sound fine, it potentially causes the wrong image tuning
parameters to be applied (e.g. tuning parameters for NTSC are applied to
a PAL source), and may confuse users about what the actual standard is
in use.
This commit explicitly configures the color standard the decoder will
use, making it visually obvious if a wrong standard was chosen.
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The user-supplied norm value gets overwritten by the generic .norm
member from the norm_params. That way, we lose the specific norm the
user may want to set.
For instance, if the user specifies V4L2_STD_PAL_60, the value actually
used will be V4L2_STD_525_60, which in the end will be as if the user
had specified V4L2_STD_NTSC, since this is always the first bitfield we
match the norm value against before configuring the hardware.
The norm_params array is only there to match a norm with an output
resolution. The norm value itself should not be changed.
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Make use of the V4L2_STD_525_60 and V4L2_STD_625_50 defines to
determine the vertical resolution to use when capturing.
V4L2_STD_525_60 (resp. V4L2_STD_625_50) is the set of standards using
525 (resp. 625) lines per frame, independently of the color encoding.
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Add support for the SECAM norm, using the "AVSECAM" decoder configuration
sequence found in Windows driver's .INF file.
For reference, the "AVSECAM" sequence in the .INF file is:
0x04,0x73,0xDC,0x72,0xA2,0x90,0x35,0x01,0x30,0x04,0x08,0x2D,0x28,0x08,
0x02,0x69,0x16,0x35,0x21,0x16,0x36
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Re-format the register {address, value} pairs so they follow the same
order as the decoder configuration sequences in the Windows driver's .INF
file.
For instance, for PAL, the "AVPAL" sequence in the .INF file is:
0x04,0x68,0xD3,0x72,0xA2,0xB0,0x15,0x01,0x2C,0x10,0x20,0x2e,0x08,0x02,
0x02,0x59,0x16,0x35,0x17,0x16,0x36
Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are several thermal sensors that only have a low-speed bus
interface but output valid video data. This patchset enables support
for the AMG88xx "Grid-Eye" sensor family.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
[hans.verkuil@cisco.com: split up int ret = ...->xfer(); line]
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Assigning subdev flags in probe() after v4l2_i2c_subdev_init() clears the
I2C flag set by that function. Fix this by using bitwise or instead.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver has event support implemented but fails to set the flag
enabling event support. Set the flag to enable control events.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check that no error happened during adding controls to the driver's
control handler. Print an error message and bail out if there was one.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Check that creating the control actually succeeded before accessing it.
A failure would lead to NULL pointer reference. Fix this.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The driver has 12 controls, not 2.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make these const as they are only used as a copy operation.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Make this const as it is only stored in a const field of a
video_device structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
All sound drivers that don't depend on PNP can be safelly
build with COMPILE_TEST, as ISA provides function stubs to
be used for such purposes.
As a side effect, with this change, the radio-miropcm20
can now be built outside i386 with COMPILE_TEST.
It should be noticed that ISAPNP currently depends on ISA.
So, on drivers that depend on it, we need to add an
explicit dependency on ISA, at least until another patch
removes it.
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There aren't much things required for it to build with COMPILE_TEST.
It just needs to not compile the code that depends on arm-specific
iommu implementation.
Co-developed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The omap3isp driver can't be compiled on non-ARM platforms but has no
compile-time dependency on OMAP. It however requires common clock
framework support, which isn't provided by all ARM platforms.
Drop the OMAP dependency when COMPILE_TEST is set and add ARM and
COMMON_CLK dependencies.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the SoC specific information for Renesas r8a77970.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the SoC specific information for Renesas r8a7796.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the SoC specific information for Renesas r8a7795 ES1.x and ES2.0.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The procedure to start or stop streaming using the non-MC single
subdevice and the MC graph and multiple subdevices are quite different.
Create a new function to abstract which method is used based on which
mode the driver is running in and add logic to start the MC graph.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the ability to process media device link change requests. Link
enabling is a bit complicated on Gen3, whether or not it's possible to
enable a link depends on what other links already are enabled. On Gen3
the 8 VINs are split into two subgroup's (VIN0-3 and VIN4-7) and from a
routing perspective these two groups are independent of each other.
Each subgroup's routing is controlled by the subgroup VIN master
instance (VIN0 and VIN4).
There are a limited number of possible route setups available for each
subgroup and the configuration of each setup is dictated by the
hardware. On H3 for example there are 6 possible route setups for each
subgroup to choose from.
This leads to the media device link notification code being rather large
since it will find the best routing configuration to try and accommodate
as many links as possible. When it's not possible to enable a new link
due to hardware constrains the link_notifier callback will return
-EMLINK.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The parsing and registering CSI-2 subdevices with the v4l2 async
framework is a collaborative effort shared between the VIN instances
which are part of the group. When the last VIN in the group is probed it
asks all other VINs to parse its share of OF and record the async
subdevices it finds in the notifier belonging to the last probed VIN.
Once all CSI-2 subdevices in this notifier are bound proceed to register
all VIN video devices of the group and crate media device links between
all CSI-2 and VIN entities according to the SoC specific routing
configuration.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Each Gen3 SoC has a limited set of predefined routing possibilities for
which CSI-2 device and channel can be routed to which VIN instance.
Prepare to store this information in the struct rvin_info.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The rcar-vin driver needs to be part of a media controller to support
Gen3. Give each VIN instance a unique name so it can be referenced from
userspace.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In media controller mode all VIN instances needs to be part of the same
media graph. There is also a need for each VIN instance to know about
and in some cases be able to communicate with other VIN instances.
Add an allocator framework where the first VIN instance to be probed
creates a shared data structure and registers a media device.
Consecutive VINs insert themself into the global group.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Prepare for media controller by calling a different initialization then
when running in device centric mode. Add trivial configuration of
the mbus and creation of the media pad for the video device entity.
While we are at it clearly mark the digital device centric notifier
functions with a comment.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The V4L2 specification clearly documents the colorspace fields as being
set by drivers for capture devices. Using the values supplied by
userspace thus wouldn't comply with the API. Until the API is updated to
allow for userspace to set these Hans wants the fields to be set by the
driver to fixed values.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When the driver runs in media controller mode it should not directly
control the subdevice instead userspace will be responsible for
configuring the pipeline. To be able to run in this mode a different set
of v4l2 operations needs to be used.
Add a new set of v4l2 operations to support operation without directly
interacting with the source subdevice.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On Gen3 a media controller API needs to be used to allow userspace to
configure the subdevices in the pipeline instead of directly controlling
a single source subdevice, which is and will continue to be the mode of
operation on Gen2.
Prepare for these two modes of operation by adding a flag to struct
rvin_info which will control which mode to use.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On Gen3 the CSI-2 routing is controlled by the VnCSI_IFMD register. One
feature of this register is that it's only present in the VIN0 and VIN4
instances. The register in VIN0 controls the routing for VIN0-3 and the
register in VIN4 controls routing for VIN4-7.
To be able to control routing from a media device this function is need
to control runtime PM for the subgroup master (VIN0 and VIN4). The
subgroup master must be switched on before the register is manipulated,
once the operation is complete it's safe to switch the master off and
the new routing will still be in effect.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the register needed to work with Gen3 hardware. This patch adds
the logic for how to work with the Gen3 hardware. More work is required
to enable the subdevice structure needed to configure capturing.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Bus configuration will once the driver is extended to support Gen3
contain information not specific to only the directly connected parallel
subdevice. Move it to struct rvin_dev to show it's not always coupled
to the parallel subdevice.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
At stream on time the driver should not query the subdevice for which
standard are used. Instead it should be cached when userspace sets the
standard and used at stream on time.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
With the recent cleanup of the format code to prepare for Gen3 it's
possible to simplify the Gen2 format code path as well. Clean up the
process by defining two functions to handle the set format and reset of
format when the standard is changed.
While at it replace the driver local struct rvin_source_fmt with a
struct v4l2_rect as all it's used for is keep track of the source
dimensions.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Part of the format alignment and checking can be shared with the Gen3
format handling. Break that part out to a separate function.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the pixelformat is not supported it should not fail but be set to
something that works. While we are at it move the two different
checks of the pixelformat to the same statement.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Remove over complicated logic to calculate the value for bytesperline
and sizeimage that was carried over from the soc_camera port. There is
no need to find the max value of bytesperline and sizeimage from
user-space as they are set to 0 before the max_t() operation.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There was never proper support in the VIN driver to deliver ALTERNATING
field format to user-space, remove this field option. The problem is
that ALTERNATING field order requires the sequence numbers of buffers
returned to userspace to reflect if fields were dropped or not,
something which is not possible with the VIN drivers capture logic.
The VIN driver can still capture from a video source which delivers
frames in ALTERNATING field order, but needs to combine them using the
VIN hardware into INTERLACED field order. Before this change if a source
was delivering fields using ALTERNATE the driver would default to
combining them using this hardware feature. Only if the user explicitly
requested ALTERNATE field order would incorrect frames be delivered.
The height should not be cut in half for the format for TOP or BOTTOM
fields settings. This was a mistake and it was made visible by the
scaling refactoring. Correct behavior is that the user should request a
frame size that fits the half height frame reflected in the field
setting. If not the VIN will do its best to scale the top or bottom to
the requested format and cropping and scaling do not work as expected.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the field is not supported by the driver it should not try to keep
the current field. Instead it should set it to a default fallback. Since
trying a format should always result in the same state regardless of the
current state of the device.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The logic to preserve the requested format width and height are too
complex and come from a premature optimization for Gen3. All Gen2 SoC
can scale and the Gen3 implementation will not use these functions at
all so simply preserve the width and height when interacting with the
subdevice much like the field is preserved simplifies the logic quite a
bit.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation of refactoring the scaling code move the code regarding
scaling to to the top of the file to avoid the need to add forward
declarations. No code is changed in this commit only whole functions
moved inside the same file.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On Gen3 the max supported width and height will be different from Gen2.
Move the limits to the struct rvin_info to prepare for Gen3 support.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When Gen3 support is added to the driver more than model ID will be
different for the different SoCs. To avoid a lot of if statements in the
code create a struct rvin_info to store this information.
While we are at it rename the poorly chosen enum which contains the
different model IDs from chip_id to model_id. Also sort the compatible
string entries and make use of of_device_get_match_data() which will
always work as the driver is DT only, so there's always a valid match.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In preparation for Gen3 support move the subdevice initialization and
clean up from rvin_v4l2_{register,unregister}() directly to the async
callbacks. This simplifies the addition of Gen3 support as the
rvin_v4l2_register() can be shared for both Gen2 and Gen3 while direct
subdevice control are only used on Gen2.
While moving this code drop a large comment which is copied from the
framework documentation and fold rvin_mbus_supported() into its only
caller. Also move the initialization and cleanup code to separate
functions to increase readability.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If the video device was registered by the complete() callback it should
be unregistered when a device is unbound from the driver. Protect from
printing an uninitialized video device node name by adding a check in
rvin_v4l2_unregister() to identify that the video device is registered.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The functions to register and unregister the hardware and video device
where poorly named from the start. Rename them to better describe their
intended function.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The usage of of_device_get_match_data() reduce the code size a bit.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Because I will be leaving Samsung soon, update my e-mail to the
etezian.org mail.
Cc: Andi Shyti <andi@etezian.org>
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The HVR 1300 has a Z8F0811 IR device, which can do both IR transmit
and receive. The transmit part was not probed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
mceusb devices have a default timeout of 100ms, but this can be changed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The last usb packet with IR data will end with 0x80 (MCE_IRDATA_TRAILER).
If we reset the decoder state at this point, IR decoding can fail.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MCE keyboard sends both key down and key up events. We have a timeout
handler mce_kbd_rx_timeout() in case the keyup event is never received;
however, this may race with new key down events from occurring.
The race is that key down scancode arrives and key down events are
generated. The timeout handler races this and generates key up events
straight afterwards. Since the keyboard generates scancodes every 100ms,
most likely the keys will be repeated 100ms later, and now we have new
key down events and the user sees duplicate key presses.
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There is nothing to sync in this code path.
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The MCE Remote sends a 0 scancode when keys are released. If this is not
received or decoded, then keys can get "stuck"; the keyup event is not
sent since the input_sync() is missing from the timeout handler.
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
If two keys are pressed, then both keys are encoded in the scancode. This
makes the mce keyboard more responsive.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The mce keyboard repeats pressed keys every 100ms. If the IR timeout
is set to less than that, we send key up events before the repeat
arrives, so we have key up/key down for each IR repeat.
The keyboard ends any sequence with a 0 scancode, in which case all keys
are cleared so there is no need to run the timeout timer: it only exists
for the case that the final 0 was not received.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Each IR protocol has its own repeat period. We can minimise the keyup
timer to be the protocol period + IR timeout. This makes keys less
"sticky" and makes IR more reactive and nicer to use.
This feature was previously attempted in commit d57ea877af ("media: rc:
per-protocol repeat period"), but that did not take the IR timeout into
account, and had to be reverted.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Since the kernel now modifies the timeout, make it possible to retrieve
the current value.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The longer the IR timeout, the longer the rc device waits until delivering
the trailing space. So, by reducing this timeout, we reduce the delay for
the last scancode to be delivered.
Note that the lirc daemon disables all protocols, in which case we revert
back to the default value.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
On the raspberry pi, we might have two lirc devices; one for sending and
one for receiving. This change makes it much more apparent which one
is which.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In Video Pixel/Line Pre-Clip Register, the setting value can be
set in 1 line unit, but it can only be specified as a multiple of
4 by v4l_bound_align_image function().
So correct that it can be specified in 1 line unit with this patch.
Signed-off-by: Koji Matsuoka <koji.matsuoka.xm@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Setting v with the CEC_PIN_EVENT_FL_DROPPED is incorrect, instead
ev should be set with this bit. Fix this.
Detected by CoverityScan, CID#1467974 ("Extra high-order bits")
Fixes: 6ec1cbf6b1 ("media: cec: improve CEC pin event handling")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
User reports AverMedia DVD EZMaker 7 can be driven by VIDEO_GRABBER.
Add the device to the id_table to make it work.
BugLink: https://bugs.launchpad.net/bugs/1620762
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The OMAP3 ISP driver manages its MMU mappings through the IOMMU-aware
ARM DMA backend. The current code creates a dma_iommu_mapping and
attaches this to the ISP device, but never detaches the mapping in
either the probe failure paths or the driver remove path resulting
in an unbalanced mapping refcount and a memory leak. Fix this properly.
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Suman Anna <s-anna@ti.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This file does a lot of non-trivial struff. Document it using
kernel-doc markups where needed and improve the comments inside
do_video_ioctl().
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Making the cast right for get_user/put_user is not trivial, as
it needs to ensure that the types are the correct ones.
Improve it by using macros.
Tested with vivid with:
$ sudo modprobe vivid no_error_inj=1
$ v4l2-compliance-32bits -a -s10 >32bits && v4l2-compliance-64bits -a -s10 > 64bits && diff -U0 32bits 64bits
--- 32bits 2018-04-17 11:18:29.141240772 -0300
+++ 64bits 2018-04-17 11:18:40.635282341 -0300
@@ -1 +1 @@
-v4l2-compliance SHA : bc71e4a67c6fbc5940062843bc41e7c8679634ce, 32 bits
+v4l2-compliance SHA : bc71e4a67c6fbc5940062843bc41e7c8679634ce, 64 bits
Using the latest version of v4l-utils with this patch applied:
https://patchwork.linuxtv.org/patch/48746/
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
In the past, "up" were an acronym for "user pointer" and "kp" for
"kernel pointer". However, since commit a1dfb4c48c ("media:
v4l2-compat-ioctl32.c: refactor compat ioctl32 logic"), both
are now __user pointers.
So, the usage of "kp" is really misleading there. So, rename
both to just "p32" and "p64" everywhere it occurs, in order to
make peace with this file's namespace.
There are two exceptions to "up/kp" nomenclature: at
alloc_userspace() and at do_video_ioctl().
There, a new userspace pointer were allocated, in order to store
the 64 bits version of the ioctl. Those were called as "up_native",
with is, IMHO, an even worse name, as "native" could mislead of
being the arguments that were filled from userspace. I almost
renamed it to just "p64", but, after thinking more about that,
it sounded better to call it as "new_p64", as this makes clearer
that this is the data structure that was allocated inside this
file in order to be used to pass/retrieve data when calling the
64-bit ready file->f_op->unlocked_ioctl() function.
Suggested-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Suggested-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of +=, the rule had :=, with actually disables build
of everything else.
Fixes: 58757984ca ("media: si470x: allow build both USB and I2C at the same time")
Reported-by: Daniel Scheller <d.scheller.oss@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The check for a valid ptr in ddb_io->dma isn't really necessary since only
devices that do data transport using DMA are supported by the driver, and
all previous initialisation code (through input_init(), output_init() and
dma_init(), has_dma is always true as it's set in ddb_probe() during
driver load) guarantees the ptr is set.
As a side effect, this silences these sparse warnings (albeit them being
false positives as ddb_io->dma won't change in these functions so the
condition always equals to the same result):
drivers/media/pci/ddbridge/ddbridge-core.c:495:9: warning: context imbalance in 'ddb_output_start' - different lock contexts for basic block
drivers/media/pci/ddbridge/ddbridge-core.c:510:9: warning: context imbalance in 'ddb_output_stop' - different lock contexts for basic block
drivers/media/pci/ddbridge/ddbridge-core.c:525:9: warning: context imbalance in 'ddb_input_stop' - different lock contexts for basic block
drivers/media/pci/ddbridge/ddbridge-core.c:560:9: warning: context imbalance in 'ddb_input_start' - different lock contexts for basic block
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/pci/mantis/mantis_uart.c:105 mantis_uart_work() warn: this loop depends on readl() succeeding
If something goes wrong at readl(), the logic will stay there
inside an IRQ code forever. This is not the nicest thing to
do :-)
So, add a timeout there, preventing staying inside the IRQ
for more than 10ms.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/rc/st_rc.c:110 st_rc_rx_interrupt() warn: this loop depends on readl() succeeding
If something goes wrong at readl(), the logic will stay there
inside an IRQ code forever. This is not the nicest thing to
do :-)
So, add a timeout there, preventing staying inside the IRQ
for more than 10ms.
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/v4l2-core/v4l2-compat-ioctl32.c:879 put_v4l2_ext_controls32() warn: check for integer overflow 'count'
The access_ok() logic should check for too big arrays too.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The omap/omap3 and viu drivers are for 32 bit platforms only.
There, a pointer has 32 bits. Now that those drivers build
for 64 bits with COMPILE_TEST, they produce the following
warnings:
drivers/media/platform/omap/omap_vout_vrfb.c: In function 'omap_vout_allocate_vrfb_buffers':
drivers/media/platform/omap/omap_vout_vrfb.c:57:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
memset((void *) vout->smsshado_virt_addr[i], 0,
^
drivers/media/platform/fsl-viu.c: In function 'viu_setup_preview':
drivers/media/platform/fsl-viu.c:753:28: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
reg_val.field_base_addr = (u32)dev->ovbuf.base;
^
drivers/media/platform/omap/omap_vout.c: In function 'omap_vout_get_userptr':
drivers/media/platform/omap/omap_vout.c:209:25: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
*physp = virt_to_phys((void *)virtp);
^
drivers/media/platform/omap3isp/ispccdc.c: In function 'ccdc_config':
drivers/media/platform/omap3isp/ispccdc.c:738:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
(__force void __user *)fpc.fpcaddr,
^
Add some typecasts to remove those warnings when building for
64 bits.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
drivers/media/cec/cec-pin-error-inj.c:231
cec_pin_error_inj_parse_line() error: uninitialized symbol 'pos'.
The tx-add-bytes command didn't check for the presence of an argument, and
also didn't check that it was > 0.
This should fix this error.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The logic at v4l2_fwnode_reference_parse_int_props() is somewhat
complex and violates Linux coding style, as it does multiple
statements on a single line. That makes static analyzers to
be confused, as warned by smatch:
drivers/media/v4l2-core/v4l2-fwnode.c:832 v4l2_fwnode_reference_parse_int_props() warn: passing zero to 'PTR_ERR'
Simplify the logic, in order to make clearer about what happens
when v4l2_fwnode_reference_get_int_prop() returns an error.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As warned by smatch:
drivers/media/dvb-core/dvb_frontend.c:314 dvb_frontend_get_event() warn: inconsistent returns 'sem:&fepriv->sem'.
Locked on: line 288
line 295
line 306
line 314
Unlocked on: line 303
The lock implementation for get event is wrong, as, if an
interrupt occurs, down_interruptible() will fail, and the
routine will call up() twice when userspace calls the ioctl
again.
The bad code is there since when Linux migrated to git, in
2005.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Solve those warnings:
drivers/media/platform/fsl-viu.c:299 restart_video_queue() warn: argument 3 to %08lx specifier is cast from pointer
drivers/media/platform/fsl-viu.c:506 buffer_queue() warn: argument 2 to %08lx specifier is cast from pointer
drivers/media/platform/fsl-viu.c:518 buffer_queue() warn: argument 2 to %08lx specifier is cast from pointer
drivers/media/platform/fsl-viu.c:528 buffer_queue() warn: argument 2 to %08lx specifier is cast from pointer
drivers/media/platform/fsl-viu.c:1219 viu_open() warn: argument 2 to %08lx specifier is cast from pointer
drivers/media/platform/fsl-viu.c:1219 viu_open() warn: argument 3 to %08lx specifier is cast from pointer
drivers/media/platform/fsl-viu.c:1219 viu_open() warn: argument 4 to %08lx specifier is cast from pointer
drivers/media/platform/fsl-viu.c:1329 viu_mmap() warn: argument 2 to %08lx specifier is cast from pointer
drivers/media/platform/fsl-viu.c:1334 viu_mmap() warn: argument 2 to %08lx specifier is cast from pointer
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The 'from' variable at preview_config() expects an __user * type.
However, the logic there does:
from = *(void * __user *) ((void *)cfg + attr->config_offset);
With actually means a void pointer, pointing to a void __ user
pointer. When the first pointer is de-referenced with *(foo),
the type it returns is "void *" instead of "void __user *".
Change it to:
from = *(void __user **) ((void *)cfg + attr->config_offset);
in order to obtain, when de-referenced, a void __user pointer,
as desired.
That prevent those warnings:
drivers/media/platform/omap3isp/isppreview.c:893:45: warning: incorrect type in initializer (different address spaces)
drivers/media/platform/omap3isp/isppreview.c:893:45: expected void [noderef] <asn:1>*from
drivers/media/platform/omap3isp/isppreview.c:893:45: got void *[noderef] <asn:1><noident>
drivers/media/platform/omap3isp/isppreview.c:893:47: warning: dereference of noderef expression
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Instead of converting to int, use %p. That prevents this
warning:
drivers/media/platform/omap3isp/ispstat.c:451 isp_stat_bufs_alloc() warn: argument 7 to %08lx specifier is cast from pointer
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
if v4l2_subdev_call(..., VENC_GET_FLD,...) fails, it
currently returns a random value. Instead, return 1.
That's probably better than returning 0, as this is very
likely what happens in practice with the current code, as
as the probably of an unititialized 32 bits integer to
have an specific value (0, in this case), is 1/(2^32).
An alternative would be to return an error code, and
let the caller to hint, based on the past received
frame, but that sounds weird.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Currently, either USB or I2C is built. Change it to allow
having both enabled at the same time.
The main reason is that COMPILE_TEST all[yes/mod]builds will
now contain all drivers under drivers/media.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Driver build produce lots of warnings due to wrong kernel-doc markups:
drivers/media/platform/davinci/vpbe.c:60: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_current_encoder_info'
drivers/media/platform/davinci/vpbe.c:78: warning: Function parameter or member 'cfg' not described in 'vpbe_find_encoder_sd_index'
drivers/media/platform/davinci/vpbe.c:78: warning: Function parameter or member 'index' not described in 'vpbe_find_encoder_sd_index'
drivers/media/platform/davinci/vpbe.c:105: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_g_cropcap'
drivers/media/platform/davinci/vpbe.c:105: warning: Function parameter or member 'cropcap' not described in 'vpbe_g_cropcap'
drivers/media/platform/davinci/vpbe.c:127: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_enum_outputs'
drivers/media/platform/davinci/vpbe.c:127: warning: Function parameter or member 'output' not described in 'vpbe_enum_outputs'
drivers/media/platform/davinci/vpbe.c:221: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_set_output'
drivers/media/platform/davinci/vpbe.c:221: warning: Function parameter or member 'index' not described in 'vpbe_set_output'
drivers/media/platform/davinci/vpbe.c:316: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_get_output'
drivers/media/platform/davinci/vpbe.c:328: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_s_dv_timings'
drivers/media/platform/davinci/vpbe.c:328: warning: Function parameter or member 'dv_timings' not described in 'vpbe_s_dv_timings'
drivers/media/platform/davinci/vpbe.c:380: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_g_dv_timings'
drivers/media/platform/davinci/vpbe.c:380: warning: Function parameter or member 'dv_timings' not described in 'vpbe_g_dv_timings'
drivers/media/platform/davinci/vpbe.c:405: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_enum_dv_timings'
drivers/media/platform/davinci/vpbe.c:405: warning: Function parameter or member 'timings' not described in 'vpbe_enum_dv_timings'
drivers/media/platform/davinci/vpbe.c:436: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_s_std'
drivers/media/platform/davinci/vpbe.c:436: warning: Function parameter or member 'std_id' not described in 'vpbe_s_std'
drivers/media/platform/davinci/vpbe.c:475: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_g_std'
drivers/media/platform/davinci/vpbe.c:475: warning: Function parameter or member 'std_id' not described in 'vpbe_g_std'
drivers/media/platform/davinci/vpbe.c:500: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_set_mode'
drivers/media/platform/davinci/vpbe.c:500: warning: Function parameter or member 'mode_info' not described in 'vpbe_set_mode'
drivers/media/platform/davinci/vpbe.c:585: warning: Function parameter or member 'dev' not described in 'vpbe_initialize'
drivers/media/platform/davinci/vpbe.c:585: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_initialize'
drivers/media/platform/davinci/vpbe.c:779: warning: Function parameter or member 'dev' not described in 'vpbe_deinitialize'
drivers/media/platform/davinci/vpbe.c:779: warning: Function parameter or member 'vpbe_dev' not described in 'vpbe_deinitialize'
drivers/media/platform/davinci/vpbe_osd.c:144: warning: Function parameter or member 'sd' not described in '_osd_dm6446_vid0_pingpong'
drivers/media/platform/davinci/vpbe_osd.c:144: warning: Function parameter or member 'field_inversion' not described in '_osd_dm6446_vid0_pingpong'
drivers/media/platform/davinci/vpbe_osd.c:144: warning: Function parameter or member 'fb_base_phys' not described in '_osd_dm6446_vid0_pingpong'
drivers/media/platform/davinci/vpbe_osd.c:144: warning: Function parameter or member 'lconfig' not described in '_osd_dm6446_vid0_pingpong'
drivers/media/platform/davinci/vpbe_osd.c:799: warning: Function parameter or member 'sd' not described in 'try_layer_config'
drivers/media/platform/davinci/vpbe_osd.c:799: warning: Function parameter or member 'layer' not described in 'try_layer_config'
drivers/media/platform/davinci/vpbe_osd.c:799: warning: Function parameter or member 'lconfig' not described in 'try_layer_config'
drivers/media/platform/davinci/vpbe_display.c:578: warning: Function parameter or member 'disp_dev' not described in 'vpbe_try_format'
drivers/media/platform/davinci/vpbe_display.c:578: warning: Function parameter or member 'pixfmt' not described in 'vpbe_try_format'
drivers/media/platform/davinci/vpbe_display.c:578: warning: Function parameter or member 'check' not described in 'vpbe_try_format'
drivers/media/platform/davinci/vpbe_display.c:943: warning: Function parameter or member 'file' not described in 'vpbe_display_s_std'
drivers/media/platform/davinci/vpbe_display.c:943: warning: Function parameter or member 'priv' not described in 'vpbe_display_s_std'
drivers/media/platform/davinci/vpbe_display.c:943: warning: Function parameter or member 'std_id' not described in 'vpbe_display_s_std'
drivers/media/platform/davinci/vpbe_display.c:975: warning: Function parameter or member 'file' not described in 'vpbe_display_g_std'
drivers/media/platform/davinci/vpbe_display.c:975: warning: Function parameter or member 'priv' not described in 'vpbe_display_g_std'
drivers/media/platform/davinci/vpbe_display.c:975: warning: Function parameter or member 'std_id' not described in 'vpbe_display_g_std'
drivers/media/platform/davinci/vpbe_display.c:998: warning: Function parameter or member 'file' not described in 'vpbe_display_enum_output'
drivers/media/platform/davinci/vpbe_display.c:998: warning: Function parameter or member 'priv' not described in 'vpbe_display_enum_output'
drivers/media/platform/davinci/vpbe_display.c:998: warning: Function parameter or member 'output' not described in 'vpbe_display_enum_output'
drivers/media/platform/davinci/vpbe_display.c:1025: warning: Function parameter or member 'file' not described in 'vpbe_display_s_output'
drivers/media/platform/davinci/vpbe_display.c:1025: warning: Function parameter or member 'priv' not described in 'vpbe_display_s_output'
drivers/media/platform/davinci/vpbe_display.c:1025: warning: Function parameter or member 'i' not described in 'vpbe_display_s_output'
drivers/media/platform/davinci/vpbe_display.c:1054: warning: Function parameter or member 'file' not described in 'vpbe_display_g_output'
drivers/media/platform/davinci/vpbe_display.c:1054: warning: Function parameter or member 'priv' not described in 'vpbe_display_g_output'
drivers/media/platform/davinci/vpbe_display.c:1054: warning: Function parameter or member 'i' not described in 'vpbe_display_g_output'
drivers/media/platform/davinci/vpbe_display.c:1074: warning: Function parameter or member 'file' not described in 'vpbe_display_enum_dv_timings'
drivers/media/platform/davinci/vpbe_display.c:1074: warning: Function parameter or member 'priv' not described in 'vpbe_display_enum_dv_timings'
drivers/media/platform/davinci/vpbe_display.c:1074: warning: Function parameter or member 'timings' not described in 'vpbe_display_enum_dv_timings'
drivers/media/platform/davinci/vpbe_display.c:1104: warning: Function parameter or member 'file' not described in 'vpbe_display_s_dv_timings'
drivers/media/platform/davinci/vpbe_display.c:1104: warning: Function parameter or member 'priv' not described in 'vpbe_display_s_dv_timings'
drivers/media/platform/davinci/vpbe_display.c:1104: warning: Function parameter or member 'timings' not described in 'vpbe_display_s_dv_timings'
drivers/media/platform/davinci/vpbe_display.c:1137: warning: Function parameter or member 'file' not described in 'vpbe_display_g_dv_timings'
drivers/media/platform/davinci/vpbe_display.c:1137: warning: Function parameter or member 'priv' not described in 'vpbe_display_g_dv_timings'
drivers/media/platform/davinci/vpbe_display.c:1137: warning: Function parameter or member 'dv_timings' not described in 'vpbe_display_g_dv_timings'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix those two warnings
drivers/media/platform/davinci/vpbe_venc.c: In function ‘venc_set_ntsc’:
drivers/media/platform/davinci/vpbe_venc.c:230:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
u32 val;
^~~
drivers/media/platform/davinci/vpbe_venc.c: In function ‘venc_sub_dev_init’:
drivers/media/platform/davinci/vpbe_venc.c:611:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
int err;
^~~
AR drivers/media/platform/davinci/built-in.a
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Except for some includes (with doesn't seem to be used), this
driver builds fine with COMPILE_TEST.
So, add checks there to avoid building it if ARCH_DAVINCI
is not selected.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The only reason why this driver doesn't build with COMPILE_TEST
is because it includes mach/mux.h. It turns that none of the
macros defined there are used.
So, get rid of it, in order to allow it to build with
COMPILE_TEST.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Those functions are used only internally:
CC drivers/media/platform/marvell-ccic/mmp-driver.o
drivers/media/platform/marvell-ccic/mmp-driver.c:186:6: warning: no previous prototype for ‘mcam_ctlr_reset’ [-Wmissing-prototypes]
void mcam_ctlr_reset(struct mcam_camera *mcam)
^~~~~~~~~~~~~~~
drivers/media/platform/marvell-ccic/mmp-driver.c:217:6: warning: no previous prototype for ‘mmpcam_calc_dphy’ [-Wmissing-prototypes]
void mmpcam_calc_dphy(struct mcam_camera *mcam)
^~~~~~~~~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver was disabled back in 2015 from builds because
of some troubles with the platform_data definition. Now
that this got fixed, re-enable it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There's nothing that prevents building this driver with
COMPILE_TEST. So, enable it.
While here, make the Kconfig dependency cleaner by removing
the unneeded if block.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
At least on i386, building with allyesconfig doesn't enable
PREEMPT, causing cec_gpio to not build.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There aren't many things that would be needed to allow it
to build with compile test.
Add the needed bits.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are several functions that are used only inside the
driver. Stop exposing that to global symbolspace.
Get rid of the following gcc warnings:
drivers/media/platform/fsl-viu.c:240:17: warning: no previous prototype for ‘format_by_fourcc’ [-Wmissing-prototypes]
struct viu_fmt *format_by_fourcc(int fourcc)
^~~~~~~~~~~~~~~~
drivers/media/platform/fsl-viu.c:253:6: warning: no previous prototype for ‘viu_start_dma’ [-Wmissing-prototypes]
void viu_start_dma(struct viu_dev *dev)
^~~~~~~~~~~~~
drivers/media/platform/fsl-viu.c:262:6: warning: no previous prototype for ‘viu_stop_dma’ [-Wmissing-prototypes]
void viu_stop_dma(struct viu_dev *dev)
^~~~~~~~~~~~
drivers/media/platform/fsl-viu.c:807:5: warning: no previous prototype for ‘vidioc_g_fbuf’ [-Wmissing-prototypes]
int vidioc_g_fbuf(struct file *file, void *priv, struct v4l2_framebuffer *arg)
^~~~~~~~~~~~~
drivers/media/platform/fsl-viu.c:818:5: warning: no previous prototype for ‘vidioc_s_fbuf’ [-Wmissing-prototypes]
int vidioc_s_fbuf(struct file *file, void *priv, const struct v4l2_framebuffer *arg)
^~~~~~~~~~~~~
drivers/media/platform/fsl-viu.c: In function ‘viu_open’:
drivers/media/platform/fsl-viu.c:1170:6: warning: variable ‘status_cfg’ set but not used [-Wunused-but-set-variable]
u32 status_cfg;
^~~~~~~~~~
drivers/media/platform/fsl-viu.c: At top level:
drivers/media/platform/fsl-viu.c:1304:6: warning: no previous prototype for ‘viu_reset’ [-Wmissing-prototypes]
void viu_reset(struct viu_reg *reg)
^~~~~~~~~
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The isp_xclk_init_data const data isn't used anywere.
drivers/media/platform/omap3isp/isp.c:294:35: warning: ‘isp_xclk_init_data’ defined but not used [-Wunused-const-variable=]
static const struct clk_init_data isp_xclk_init_data = {
^~~~~~~~~~~~~~~~~~
Fixes: 9b28ee3c91 ("[media] omap3isp: Use the common clock framework")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This adds support for generating coredumps for remoteprocs using
devcoredump, adds the Qualcomm sysmon driver for intra-remoteproc crash
handling and a number of fixes in Qualcomm and IMX drivers.
-----BEGIN PGP SIGNATURE-----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=cxV7
-----END PGP SIGNATURE-----
Merge tag 'rproc-v4.17' of git://github.com/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
- add support for generating coredumps for remoteprocs using
devcoredump
- add the Qualcomm sysmon driver for intra-remoteproc crash handling
- a number of fixes in Qualcomm and IMX drivers
* tag 'rproc-v4.17' of git://github.com/andersson/remoteproc:
remoteproc: fix null pointer dereference on glink only platforms
soc: qcom: qmi: add CONFIG_NET dependency
remoteproc: imx_rproc: Slightly simplify code in 'imx_rproc_probe()'
remoteproc: imx_rproc: Re-use existing error handling path in 'imx_rproc_probe()'
remoteproc: imx_rproc: Fix an error handling path in 'imx_rproc_probe()'
samples: Introduce Qualcomm QMI sample client
remoteproc: qcom: Introduce sysmon
remoteproc: Pass type of shutdown to subdev remove
remoteproc: qcom: Register segments for core dump
soc: qcom: mdt-loader: Return relocation base
remoteproc: Rename "load_rsc_table" to "parse_fw"
remoteproc: Add remote processor coredump support
remoteproc: Remove null character write of shared mem
-----BEGIN PGP SIGNATURE-----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=+PjT
-----END PGP SIGNATURE-----
Merge tag 'media/v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A series of media updates/fixes for 4.17.
There are two important core fix patches in this series:
- A regression fix on Kernel 4.16 with causes it to not work with
some input devices that depend on media core
- A fix at compat32 bits with causes it to OOPS on overlay, and
affects the Kernels where the CVE-2017-13166 was backported
The remaining ones are other random fixes at the documentation and on
drivers.
The biggest part of this series is a set of 18 patches for the Intel
atomisp driver. Currently, it produces hundreds of warnings/errors on
sparse/smatch, causing me to sometimes ignore new warnings on other
drivers that are not so broken. This driver is on really poor state,
even for staging standards: it has several layers of abstraction on
it, and it supports two different hardware. Selecting between them
require to add a define (there isn't even a Kconfig option for such
purpose). Just on this smatch cleanup, I could easily get rid of 8
"do-nothing" files. So, I'm seriously considering its removal from
upstream, if I don't see any real work on addressing the problems
there along this year"
* tag 'media/v4.17-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (48 commits)
media: v4l2-core: fix size of devnode_nums[] bitarray
media: v4l2-compat-ioctl32: don't oops on overlay
media: i2c: adv748x: afe: fix sparse warning
media: extended-controls.rst: transmitter -> receiver
media: staging: atomisp: stop duplicating input format types
media: staging: atomisp: get rid of an unused var
media: staging: atomisp: stop mixing enum types
media: staging: atomisp: get rid of some static warnings
media: staging: atomisp: use %p to print pointers
media: staging: atomisp: remove an useless check
media: staging: atomisp: avoid a warning if 32 bits build
media: staging: atomisp: don't access a NULL var
media: staging: atomisp: Get rid of *default.host.[ch]
media: staging: atomisp: get rid of an unused function
media: staging: atomisp: remove unused set_pd_base()
media: staging: atomisp: fix endianess issues
media: staging: atomisp: add a missing include
media: staging: atomisp: get rid of stupid statements
media: staging: atomisp: declare static vars as such
media: staging: atomisp: ia_css_output.host: don't use var before check
...
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
kfifo: fix inaccurate comment
tools/thermal: tmon: fix for segfault
net: Spelling s/stucture/structure/
edd: don't spam log if no EDD information is present
Documentation: Fix early-microcode.txt references after file rename
tracing: Block comments should align the * on each line
treewide: Fix typos in printk
GenWQE: Fix a typo in two comments
treewide: Align function definition open/close braces
FE_GET_PROPERTY has always failed as following situations:
- Use compatible ioctl
- The array of 'struct dtv_property' has 2 or more items
This patch fixes wrong cast to a pointer 'struct dtv_property' from a
pointer of 2nd or after item of 'struct compat_dtv_property' array.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Documentation/video4linux/gspca.txt is missing.
It has moved to Documentation/media/v4l-drivers/gspca-cardlist.rst
Signed-off-by: winton.liu <18502523564@163.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The cx231xx USB bridge has issue streaming QAM256 DVB-C channels.
QAM64 channels were fine, but QAM256 channels produced corrupted
transport streams.
cx231xx alt mode 4 does not provide enough bandwidth to acommodate
QAM256 DVB-C channels, most likely DVB-T2 channels would break up
as well. Alt mode 5 increases bridge bandwidth to 90Mbps, and
fixes QAM256 DVB-C streaming.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When a BRx is provided by a pipeline, the WPF must determine the master
layer. Currently the condition to check this identifies pipe->bru ||
pipe->num_inputs > 1.
The code then moves on to dereference pipe->bru, thus the check fails
static analysers on the possibility that pipe->num_inputs could be
greater than 1 without pipe->bru being set.
The reality is that the pipeline must have a BRx to support more than
one input, thus this could never cause a fault - however it also
identifies that the num_inputs > 1 check is redundant.
Remove the redundant check - and always configure the master layer
appropriately when we have a BRx configured in our pipeline.
Fixes: 6134148f60 ("v4l: vsp1: Add support for the BRS entity")
Cc: stable@vger.kernel.org
Suggested-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The output pixel format changed by set_fmt() pad operation is not
correctly applied. It is intended to be restored by calling
ov5640_set_framefmt() when the video stream is started.
However, when the device is powered on by s_power subdev operation before
the video stream is started, the current output mode setting is restored
by ov5640_restore_mode() that also clears pending_mode_change flag in
ov5640_set_mode(). So ov5640_set_framefmt() isn't called as intended and
the output pixel format is not restored.
This change adds the missing output pixel format setting in the
ov5640_restore_mode() that is called when the device is powered on.
Cc: Steve Longerbeam <slongerbeam@gmail.com>
Cc: Hugues Fruchet <hugues.fruchet@st.com>
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Structure i2c_driver does not need to set the owner field, as this will
be populated by the driver core.
Generated by scripts/coccinelle/api/platform_no_drv_owner.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Use v4l2_find_nearest_size instead of a driver specific function to find
nearest matching size.
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The device node obtained with of_graph_get_next_endpoint() should be
released by calling of_node_put(). But it was not released when
v4l2_fwnode_endpoint_parse() failed.
This change moves the of_node_put() call before the error check and
fixes the issue.
Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Fix set of missing colorspace related fields in get_/set_fmt.
Detected by v4l2-compliance tool.
[Sakari Ailus: Rearrange fmt declaration in ov5640_probe()]
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
An older version of the driver patches were merged accidentally which
resulted in missing the array_size parameter that tells the length of the
array that contains the different supported sizes.
Bring it back to v4l2_find_nearest size and make the corresponding change
for the drivers using it as well.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
I know, it's a measly space, but I can't stand it since the
V4L2_PIX_FMT_NV24 case before this case does it right.
So add the space in order to restore blessed symmetry and
consistency and to make the world whole again...
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Older Kernels use a struct for ktime_t, which requires the conversion
function ktime_to_ns to be used on some places. With this patch it will
compile now also for older Kernel versions.
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The error return value should be fixed as it may return EPROBE_DEFER.
Cc: Bin Liu <bin.liu@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Rick Chang <rick.chang@mediatek.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
find_format_by_index() stops enumerating formats as soon as the index
matches, and returns NULL if venus_helper_check_codec() finds out that
the format is not supported. This prevents formats to be properly
enumerated if a non-supported format is present, as the enumeration will
end with it.
Fix this by moving the call to venus_helper_check_codec() into the loop,
and keep enumerating when it fails.
Fixes: 29f0133ec6 media: venus: use helper function to check supported codecs
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As pointed by smatch:
drivers/media/tuners/r820t.c:2374 r820t_attach() error: potential null dereference 'priv'. (kzalloc returns null)
The current function with prints error assumes that the attach
succeeds. So, don't use it in case of failures.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
-----BEGIN PGP SIGNATURE-----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=bzhS
-----END PGP SIGNATURE-----
Merge tag 'media/v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new CEC pin injection code for testing purposes
- DVB frontend cxd2099 promoted from staging
- new platform driver for Sony cxd2880 DVB devices
- new sensor drivers: mt9t112, ov2685, ov5695, ov772x, tda1997x,
tw9910.c
- removal of unused cx18 and ivtv alsa mixers
- the reneseas-ceu driver doesn't depend on soc_camera anymore and
moved from staging
- removed the mantis_vp3028 driver, unused since 2009
- s5p-mfc: add support for version 10 of the MSP
- added a decoder for imon protocol
- atomisp: lots of cleanups
- imx074 and mt9t031: don't depend on soc_camera anymore, being
promoted from staging
- added helper functions to better support DVB I2C binding
- lots of driver improvements and cleanups
* tag 'media/v4.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (438 commits)
media: v4l2-ioctl: rename a temp var that stores _IOC_SIZE(cmd)
media: fimc-capture: get rid of two warnings
media: dvb-usb-v2: fix a missing dependency of I2C_MUX
media: uvc: to the right check at uvc_ioctl_enum_framesizes()
media: cec-core: fix a bug at cec_error_inj_write()
media: tda9840: cleanup a warning
media: tm6000: avoid casting just to print pointer address
media: em28xx-input: improve error handling code
media: zr364xx: avoid casting just to print pointer address
media: vivid-radio-rx: add a cast to avoid a warning
media: saa7134-alsa: don't use casts to print a buffer address
media: solo6x10: get rid of an address space warning
media: zoran: don't cast pointers to print them
media: ir-kbd-i2c: change the if logic to avoid a warning
media: ir-kbd-i2c: improve error handling code
media: saa7134-input: improve error handling
media: s2255drv: fix a casting warning
media: ivtvfb: Cleanup some warnings
media: videobuf-dma-sg: Fix a weird cast
soc_camera: fix a weird cast on printk
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
Pull wait_var_event updates from Ingo Molnar:
"This introduces the new wait_var_event() API, which is a more flexible
waiting primitive than wait_on_atomic_t().
All wait_on_atomic_t() users are migrated over to the new API and
wait_on_atomic_t() is removed. The migration fixes one bug and should
result in no functional changes for the other usecases"
* 'sched-wait-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/wait: Improve __var_waitqueue() code generation
sched/wait: Remove the wait_on_atomic_t() API
sched/wait, arch/mips: Fix and convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, fs/ocfs2: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, fs/nfs: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, fs/fscache: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, fs/btrfs: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, fs/afs: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, drivers/media: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait, drivers/drm: Convert wait_on_atomic_t() usage to the new wait_var_event() API
sched/wait: Introduce wait_var_event()
