Based on Thomas Renninger's feedback/ideas. Re-structure the code
to better handle the per_cpu_schedule mechanism which was introduced
when adding support for AMD Zen based processors.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
AMD Zen 2 introduces the RDPRU instruction which can be used to access some
processor registers which are typically only accessible in privilege level
0. ECX specifies the register to read and EDX:EAX will contain the value read.
ECX: 0 - Register MPERF
1 - Register APERF
This has the added advantage of not having to use the msr module, since the
userspace to kernel transitions which occur during each read_msr() might
cause APERF and MPERF to go out of sync.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
The per_cpu_schedule flag is used to move the cpupower process to the cpu
on which we are looking to read the APERF/MPERF registers.
This prevents IPIs from being generated by read_msr()s as we are already
on the cpu of interest.
Ex: If cpupower is running on CPU 0 and we execute
read_msr(20, MSR_APERF, val) then,
read_msr(20, MSR_MPERF, val)
the msr module will generate an IPI from CPU 0 to CPU 20 to query
for the MSR_APERF and then the MSR_MPERF in separate IPIs.
This delay, caused by IPI latency, between reading the APERF and MPERF
registers may cause both of them to go out of sync.
The use of the per_cpu_schedule flag reduces the probability of this
from happening. It comes at the cost of a negligible increase in cpu
consumption caused by the migration of cpupower across each of the
cpus of the system.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Move the needs_root variable into a sub-struct. This is in preparation
for adding a new flag for cpuidle_monitor.
Update all uses of the needs_root variable to reflect this change.
Signed-off-by: Janakarajan Natarajan <Janakarajan.Natarajan@amd.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Cpupower tool has set and info options which are being used only by
x86 machines. This patch removes support for these two subcommands
from cpupower utility for POWER. Thus, these two subcommands will now be
available only for intel.
This removes the ambiguous error message while using set option in case
of using non-intel systems.
Without this patch on a POWER system:
root@ubuntu:~# cpupower info
System does not support Intel's performance bias setting
root@ubuntu:~# cpupower set -b 10
Error setting perf-bias value on CPU
With this patch on a POWER box:
root@ubuntu:~# cpupower info
Subcommand not supported on POWER
Same result for set subcommand.
This patch does not affect results on a intel box.
Signed-off-by: Abhishek Goel <huntbag@linux.vnet.ibm.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
When building cpupower with clang, the following warning appears:
utils/idle_monitor/hsw_ext_idle.c:42:16: warning: initializer overrides
prior initialization of this subobject [-Winitializer-overrides]
.desc = N_("Processor Package C2"),
^~~~~~~~~~~~~~~~~~~~~~
./utils/helpers/helpers.h:25:33: note: expanded from macro 'N_'
#define N_(String) gettext_noop(String)
^~~~~~
./utils/helpers/helpers.h:23:30: note: expanded from macro
'gettext_noop'
#define gettext_noop(String) String
^~~~~~
utils/idle_monitor/hsw_ext_idle.c:41:16: note: previous initialization
is here
.desc = N_("Processor Package C9"),
^~~~~~~~~~~~~~~~~~~~~~
./utils/helpers/helpers.h:25:33: note: expanded from macro 'N_'
#define N_(String) gettext_noop(String)
^~~~~~
./utils/helpers/helpers.h:23:30: note: expanded from macro
'gettext_noop'
#define gettext_noop(String) String
^~~~~~
1 warning generated.
This appears to be a copy and paste or merge mistake because the name
and id fields both have PC9 in them, not PC2. Remove the second
assignment to fix the warning.
Fixes: 7ee767b69b ("cpupower: Add Haswell family 0x45 specific idle monitor to show PC8,9,10 states")
Link: https://github.com/ClangBuiltLinux/linux/issues/718
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
* Fix compilation error of ASUS WMI driver when CONFIG_ACPI_BATTERY=n.
* Fix I²C multi-instantiate driver to work with several USB PD devices.
* Fix boot issue on Siemens SIMATIC IPC277E when PMC critical clock is
being disabled.
* Plenty of fixes to Intel Speed-Select Technology tools.
The following is an automated git shortlog grouped by driver:
asus-wmi:
- Make it depend on ACPI battery API
i2c-multi-instantiate:
- Derive the device name from parent
pmc_atom:
- Add Siemens SIMATIC IPC277E to critclk_systems DMI table
tools/power/x86/intel-speed-select:
- Fix perf-profile command output
- Extend core-power command set
- Fix some debug prints
- Format get-assoc information
- Allow online/offline based on tdp
- Fix high priority core mask over count
-----BEGIN PGP SIGNATURE-----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=Cd14
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.4-2' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform-drivers fixes from Andy Shevchenko:
- Fix compilation error of ASUS WMI driver when CONFIG_ACPI_BATTERY=n
- Fix I²C multi-instantiate driver to work with several USB PD devices
- Fix boot issue on Siemens SIMATIC IPC277E when PMC critical clock is
being disabled
- Plenty of fixes to Intel Speed-Select Technology tools
* tag 'platform-drivers-x86-v5.4-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: i2c-multi-instantiate: Derive the device name from parent
platform/x86: pmc_atom: Add Siemens SIMATIC IPC277E to critclk_systems DMI table
tools/power/x86/intel-speed-select: Fix perf-profile command output
tools/power/x86/intel-speed-select: Extend core-power command set
tools/power/x86/intel-speed-select: Fix some debug prints
tools/power/x86/intel-speed-select: Format get-assoc information
tools/power/x86/intel-speed-select: Allow online/offline based on tdp
tools/power/x86/intel-speed-select: Fix high priority core mask over count
platform/x86: asus-wmi: Make it depend on ACPI battery API
commit "c016ae8f9fa04d361efc8629de49ad3af12b5262
"tools/power/x86/intel-speed-select: Output success/failed for command
output" introduced a regression in perf-profile outputs. With this
the result field is changed to string interpreting every non zero
value as errors. But these commands display on zero (>0) result.
For example before this commit the display was:
package-1
die-0
cpu-14
get-config-levels:4
Here the get-config-levels is interpreted as error and displayed
as error with the above commit:
package-1
die-0
cpu-14
get-config-levels:failed(error 4)
Fix this issue by not using isst_display_result() to display such results,
but define a new function which formats this data and prints.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add additional command to get the clos enable and priority type. The
current info option is actually dumping per clos QOS config, so name
the command appropriately to get-config.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Fix wrong debug print for cpu, which is displayed as CLOS. Also
avoid printing clos id, when user is specify clos as parameter.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Format the get-assoc command output consistant with other commands.
For example:
Intel(R) Speed Select Technology
Executing on CPU model:142[0x8e]
package-0
die-0
cpu-0
get-assoc
clos:0
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Using enable core mask, do online offline CPUs. There is a new option
--online|-o for set-config-level.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If the CPU package has the less logical CPU than topo_max_cpus, but un-present
CPU's punit_cpu_core will be initiated to 0 and they will be count to core 0
Like below, there are only 10 high priority cores (20 logical CPUs) in the CPU
package, but it count to 27 logic CPUs.
./intel-speed-select base-freq info -l 0 | grep mask
high-priority-cpu-mask:7f000179,f000179f
With the fix patch:
./intel-speed-select base-freq info -l 0
high-priority-cpu-mask:00000179,f000179f
Signed-off-by: Youquan Song <youquan.song@intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
- Update the ACPICA code in the kernel to upstream revision 20190816
including:
* Internal limits change to support larger systems (Bob Moore).
* Macros clean up (Bob Moore).
* printf format string fixes (Bob Moore).
* Full deployment of the ACPI_PRINTF_LIKE macro (Bob Moore).
* Tools improvements (Bob Moore, Colin Ian King).
* Windows _OSI support fixes (Jung-uk Kim).
- Improve memory hot-add support in the ACPI HMAT handling code (Dan
Williams, Keith Busch).
- Fix the ACPI LPSS (Low-Power Subsystem) driver for Intel SoCs to
save and restore private registers during system-wide suspend and
resume on systems with the Lynxpoint PCH (Jarkko Nikula).
- Convert the ACPI documentation related to LEDs to ReST (Sakari
Ailus).
- Fix assorted issues and make assorted minor improvements in the
ACPI-related code (Al Stone, Andy Shevchenko, Jiri Slaby, Kelsey
Skunberg, Krzysztof Wilczynski, Liguang Zhang, Wenwen Wang,
YueHaibing).
-----BEGIN PGP SIGNATURE-----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=2Tf0
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These include an ACPICA update (to upstream revision 20190816),
improvements of support for memory hot-add in the HMAT handling code
and some assorted fixes and cleanups.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20190816
including:
* Internal limits change to support larger systems (Bob Moore).
* Macros clean up (Bob Moore).
* printf format string fixes (Bob Moore).
* Full deployment of the ACPI_PRINTF_LIKE macro (Bob Moore).
* Tools improvements (Bob Moore, Colin Ian King).
* Windows _OSI support fixes (Jung-uk Kim).
- Improve memory hot-add support in the ACPI HMAT handling code (Dan
Williams, Keith Busch).
- Fix the ACPI LPSS (Low-Power Subsystem) driver for Intel SoCs to
save and restore private registers during system-wide suspend and
resume on systems with the Lynxpoint PCH (Jarkko Nikula).
- Convert the ACPI documentation related to LEDs to ReST (Sakari
Ailus).
- Fix assorted issues and make assorted minor improvements in the
ACPI-related code (Al Stone, Andy Shevchenko, Jiri Slaby, Kelsey
Skunberg, Krzysztof Wilczynski, Liguang Zhang, Wenwen Wang,
YueHaibing)"
* tag 'acpi-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
ACPI / PCI: fix acpi_pci_irq_enable() memory leak
ACPI: custom_method: fix memory leaks
ACPI: thermal: Remove redundant acpi_has_method() calls
ACPI / CPPC: do not require the _PSD method
ACPI: SBS: remove unused const variable 'SMBUS_PEC'
ACPI / LPSS: Save/restore LPSS private registers also on Lynxpoint
ACPI/PCI: Remove surplus parentheses from a return statement
ACPICA: Update version to 20190816.
ACPICA: Add "Windows 2019" string to _OSI support.
ACPICA: Differentiate Windows 8.1 from Windows 8.
ACPICA: Fully deploy ACPI_PRINTF_LIKE macro
ACPICA: iASL,acpi_dump: Improve y/n query
ACPICA: Fix issues with arg types within printf format strings
ACPICA: Macros: remove pointer math on a null pointer
ACPICA: Increase total number of possible Owner IDs
ACPICA: Debugger: remove redundant assignment on obj_desc
Documentation: ACPI: DSD: Convert LED documentation to ReST
ACPI / APEI: Release resources if gen_pool_add() fails
HMAT: Skip publishing target info for nodes with no online memory
HMAT: Register attributes for memory hot add
...
- Rework the main suspend-to-idle control flow to avoid repeating
"noirq" device resume and suspend operations in case of spurious
wakeups from the ACPI EC and decouple the ACPI EC wakeups support
from the LPS0 _DSM support (Rafael Wysocki).
- Extend the wakeup sources framework to expose wakeup sources as
device objects in sysfs (Tri Vo, Stephen Boyd).
- Expose system suspend statistics in sysfs (Kalesh Singh).
- Introduce a new haltpoll cpuidle driver and a new matching
governor for virtualized guests wanting to do guest-side polling
in the idle loop (Marcelo Tosatti, Joao Martins, Wanpeng Li,
Stephen Rothwell).
- Fix the menu and teo cpuidle governors to allow the scheduler tick
to be stopped if PM QoS is used to limit the CPU idle state exit
latency in some cases (Rafael Wysocki).
- Increase the resolution of the play_idle() argument to microseconds
for more fine-grained injection of CPU idle cycles (Daniel Lezcano).
- Switch over some users of cpuidle notifiers to the new QoS-based
frequency limits and drop the CPUFREQ_ADJUST and CPUFREQ_NOTIFY
policy notifier events (Viresh Kumar).
- Add new cpufreq driver based on nvmem for sun50i (Yangtao Li).
- Add support for MT8183 and MT8516 to the mediatek cpufreq driver
(Andrew-sh.Cheng, Fabien Parent).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
- Add qcs404 to cpufreq-dt-platdev blacklist (Jorge Ramirez-Ortiz).
- Update the qcom cpufreq driver (among other things, to make it
easier to extend and to use kryo cpufreq for other nvmem-based
SoCs) and add qcs404 support to it (Niklas Cassel, Douglas
RAILLARD, Sibi Sankar, Sricharan R).
- Fix assorted issues and make assorted minor improvements in the
cpufreq code (Colin Ian King, Douglas RAILLARD, Florian Fainelli,
Gustavo Silva, Hariprasad Kelam).
- Add new devfreq driver for NVidia Tegra20 (Dmitry Osipenko, Arnd
Bergmann).
- Add new Exynos PPMU events to devfreq events and extend that
mechanism (Lukasz Luba).
- Fix and clean up the exynos-bus devfreq driver (Kamil Konieczny).
- Improve devfreq documentation and governor code, fix spelling
typos in devfreq (Ezequiel Garcia, Krzysztof Kozlowski, Leonard
Crestez, MyungJoo Ham, Gaël PORTAY).
- Add regulators enable and disable to the OPP (operating performance
points) framework (Kamil Konieczny).
- Update the OPP framework to support multiple opp-suspend properties
(Anson Huang).
- Fix assorted issues and make assorted minor improvements in the OPP
code (Niklas Cassel, Viresh Kumar, Yue Hu).
- Clean up the generic power domains (genpd) framework (Ulf Hansson).
- Clean up assorted pieces of power management code and documentation
(Akinobu Mita, Amit Kucheria, Chuhong Yuan).
- Update the pm-graph tool to version 5.5 including multiple fixes
and improvements (Todd Brandt).
- Update the cpupower utility (Benjamin Weis, Geert Uytterhoeven,
Sébastien Szymanski).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl2ArZ4SHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxgfYQAK80hs43vWQDmp7XKrN4pQe8+qYULAGO
fBfrFl+NG9y/cnuqnt3NtA8MoyNsMMkMLkpkEDMfSbYqqH5ehEzX5+uGJWiWx8+Y
oH5KU8MH7Tj/utYaalGzDt0AHfHZDIGC0NCUNQJVtE/4mOANFabwsCwscp4MrD5Q
WjFN8U4BrsmWgJdZ/U9QIWcDZ0I+1etCF+rZG2yxSv31FMq2Zk/Qm4YyobqCvQFl
TR9rxl08wqUmIYIz5cDjt/3AKH7NLLDqOTstbCL7cmufM5XPFc1yox69xc89UrIa
4AMgmDp7SMwFG/gdUPof0WQNmx7qxmiRAPleAOYBOZW/8jPNZk2y+RhM5NeF72m7
AFqYiuxqatkSb4IsT8fLzH9IUZOdYr8uSmoMQECw+MHdApaKFjFV8Lb/qx5+AwkD
y7pwys8dZSamAjAf62eUzJDWcEwkNrujIisGrIXrVHb7ISbweskMOmdAYn9p4KgP
dfRzpJBJ45IaMIdbaVXNpg3rP7Apfs7X1X+/ZhG6f+zHH3zYwr8Y81WPqX8WaZJ4
qoVCyxiVWzMYjY2/1lzjaAdqWojPWHQ3or3eBaK52DouyG3jY6hCDTLwU7iuqcCX
jzAtrnqrNIKufvaObEmqcmYlIIOFT7QaJCtGUSRFQLfSon8fsVSR7LLeXoAMUJKT
JWQenuNaJngK
=TBDQ
-----END PGP SIGNATURE-----
Merge tag 'pm-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a rework of the main suspend-to-idle code flow (related
to the handling of spurious wakeups), a switch over of several users
of cpufreq notifiers to QoS-based limits, a new devfreq driver for
Tegra20, a new cpuidle driver and governor for virtualized guests, an
extension of the wakeup sources framework to expose wakeup sources as
device objects in sysfs, and more.
Specifics:
- Rework the main suspend-to-idle control flow to avoid repeating
"noirq" device resume and suspend operations in case of spurious
wakeups from the ACPI EC and decouple the ACPI EC wakeups support
from the LPS0 _DSM support (Rafael Wysocki).
- Extend the wakeup sources framework to expose wakeup sources as
device objects in sysfs (Tri Vo, Stephen Boyd).
- Expose system suspend statistics in sysfs (Kalesh Singh).
- Introduce a new haltpoll cpuidle driver and a new matching governor
for virtualized guests wanting to do guest-side polling in the idle
loop (Marcelo Tosatti, Joao Martins, Wanpeng Li, Stephen Rothwell).
- Fix the menu and teo cpuidle governors to allow the scheduler tick
to be stopped if PM QoS is used to limit the CPU idle state exit
latency in some cases (Rafael Wysocki).
- Increase the resolution of the play_idle() argument to microseconds
for more fine-grained injection of CPU idle cycles (Daniel
Lezcano).
- Switch over some users of cpuidle notifiers to the new QoS-based
frequency limits and drop the CPUFREQ_ADJUST and CPUFREQ_NOTIFY
policy notifier events (Viresh Kumar).
- Add new cpufreq driver based on nvmem for sun50i (Yangtao Li).
- Add support for MT8183 and MT8516 to the mediatek cpufreq driver
(Andrew-sh.Cheng, Fabien Parent).
- Add i.MX8MN support to the imx-cpufreq-dt cpufreq driver (Anson
Huang).
- Add qcs404 to cpufreq-dt-platdev blacklist (Jorge Ramirez-Ortiz).
- Update the qcom cpufreq driver (among other things, to make it
easier to extend and to use kryo cpufreq for other nvmem-based
SoCs) and add qcs404 support to it (Niklas Cassel, Douglas
RAILLARD, Sibi Sankar, Sricharan R).
- Fix assorted issues and make assorted minor improvements in the
cpufreq code (Colin Ian King, Douglas RAILLARD, Florian Fainelli,
Gustavo Silva, Hariprasad Kelam).
- Add new devfreq driver for NVidia Tegra20 (Dmitry Osipenko, Arnd
Bergmann).
- Add new Exynos PPMU events to devfreq events and extend that
mechanism (Lukasz Luba).
- Fix and clean up the exynos-bus devfreq driver (Kamil Konieczny).
- Improve devfreq documentation and governor code, fix spelling typos
in devfreq (Ezequiel Garcia, Krzysztof Kozlowski, Leonard Crestez,
MyungJoo Ham, Gaël PORTAY).
- Add regulators enable and disable to the OPP (operating performance
points) framework (Kamil Konieczny).
- Update the OPP framework to support multiple opp-suspend properties
(Anson Huang).
- Fix assorted issues and make assorted minor improvements in the OPP
code (Niklas Cassel, Viresh Kumar, Yue Hu).
- Clean up the generic power domains (genpd) framework (Ulf Hansson).
- Clean up assorted pieces of power management code and documentation
(Akinobu Mita, Amit Kucheria, Chuhong Yuan).
- Update the pm-graph tool to version 5.5 including multiple fixes
and improvements (Todd Brandt).
- Update the cpupower utility (Benjamin Weis, Geert Uytterhoeven,
Sébastien Szymanski)"
* tag 'pm-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (126 commits)
cpuidle-haltpoll: Enable kvm guest polling when dedicated physical CPUs are available
cpuidle-haltpoll: do not set an owner to allow modunload
cpuidle-haltpoll: return -ENODEV on modinit failure
cpuidle-haltpoll: set haltpoll as preferred governor
cpuidle: allow governor switch on cpuidle_register_driver()
PM: runtime: Documentation: add runtime_status ABI document
pm-graph: make setVal unbuffered again for python2 and python3
powercap: idle_inject: Use higher resolution for idle injection
cpuidle: play_idle: Increase the resolution to usec
cpuidle-haltpoll: vcpu hotplug support
cpufreq: Add qcs404 to cpufreq-dt-platdev blacklist
cpufreq: qcom: Add support for qcs404 on nvmem driver
cpufreq: qcom: Refactor the driver to make it easier to extend
cpufreq: qcom: Re-organise kryo cpufreq to use it for other nvmem based qcom socs
dt-bindings: opp: Add qcom-opp bindings with properties needed for CPR
dt-bindings: opp: qcom-nvmem: Support pstates provided by a power domain
Documentation: cpufreq: Update policy notifier documentation
cpufreq: Remove CPUFREQ_ADJUST and CPUFREQ_NOTIFY policy notifier events
PM / Domains: Verify PM domain type in dev_pm_genpd_set_performance_state()
PM / Domains: Simplify genpd_lookup_dev()
...
* ASUS WMI driver got couple of worth to mention updates, i.e. support of
FAN is fixed for recent products and the charge threshold support has been
added.
* Two uknown key events for Dell laptops are being ignored now to avoid spam
user with harmless messages.
* HP ZBook 17 G5 and ASUS Zenbook UX430UNR have got accelerometer support.
* Intel CherryTrail platforms got a regression with wake up. Now it's fixed.
* Intel PMC driver got fixed in order to work nicely in Xen environment.
* Intel Speed Select driver provides bucket vs core count relationship.
Besides that the tools has been updated for better output.
* The PrivacyGuard is enabled on Lenovo ThinkPad laptops.
* Three tablets, i.e. Trekstor Primebook C11B 2-in-1, Irbis TW90 and
Chuwi Surbook Mini, have got touchscreen support.
The following is an automated git shortlog grouped by driver:
acer-wmi:
- Switch to acpi_dev_get_first_match_dev()
asus-nb-wmi:
- Support ALS on the Zenbook UX430UNR
asus-wmi:
- Refactor charge threshold to use the battery hooking API
- Rename CHARGE_THRESHOLD to RSOC
- Reorder ASUS_WMI_CHARGE_THRESHOLD
- Fix condition in charge_threshold_store()
- Remove unnecessary blank lines
- Drop indentation level by inverting conditionals
- Use clamp_val() instead of open coded variant
- Replace sscanf() with kstrtoint()
- Refactor charge_threshold_store()
- Add support for charge threshold
- fix CPU fan control on recent products
- add a helper for device presence
- cleanup AGFN fan handling
- Use kmemdup rather than duplicating its implementation
compal-laptop:
- Initialize "value" in ec_read_u8()
dell-wmi:
- Use existing defined KBD_LED_* magic values
- Ignore keyboard backlight change KBD_LED_AUTO_TOKEN
- Ignore keyboard backlight change KBD_LED_ON_TOKEN
hp_accel:
- Add support for HP ZBook 17 G5
i2c-multi-instantiate:
- Use struct_size() helper
intel_bxtwc_tmu:
- Remove dev_err() usage after platform_get_irq()
intel_int0002_vgpio:
- Use device_init_wakeup
- Fix wakeups not working on Cherry Trail
- Remove dev_err() usage after platform_get_irq()
intel_pmc_core:
- Do not ioremap RAM
intel_pmc_core_pltdrv:
- Module removal warning fix
intel_pmc_ipc:
- Remove dev_err() usage after platform_get_irq()
ISST:
- Allow additional TRL MSRs
- Use dev_get_drvdata
MAINTAINERS:
- Switch PDx86 subsystem status to Odd Fixes
pcengines-apuv2:
- wire up simswitch gpio as led
- add mpcie reset gpio export
platform/mellanox:
- mlxreg-hotplug: Remove dev_err() usage after platform_get_irq()
pmc_atom:
- Add Siemens SIMATIC IPC227E to critclk_systems DMI table
thinkpad_acpi:
- Add ThinkPad PrivacyGuard
- Use kmemdup rather than duplicating its implementation
tools/power/x86/intel-speed-select:
- Display core count for bucket
- Fix memory leak
- Output success/failed for command output
- Output human readable CPU list
- Change turbo ratio output to maximum turbo frequency
- Switch output to MHz
- Simplify output for turbo-freq and base-freq
- Fix cpu-count output
- Fix help option typo
- Fix package typo
- Fix a read overflow in isst_set_tdp_level_msr()
touchscreen_dmi:
- Add info for the Trekstor Primebook C11B 2-in-1
- Add info for the Irbis TW90 tablet
- Add info for the Chuwi Surbook Mini tablet
wmi:
- Remove acpi_has_method() call
-----BEGIN PGP SIGNATURE-----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=HItn
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.4-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform-drivers updates from Andy Shevchenko:
- ASUS WMI driver got a couple of updates, i.e. support of FAN is fixed
for recent products and the charge threshold support has been added
- Two uknown key events for Dell laptops are being ignored now to avoid
spamming users with harmless messages
- HP ZBook 17 G5 and ASUS Zenbook UX430UNR got accelerometer support.
- Intel CherryTrail platforms had a regression with wake up. Now it's
fixed
- Intel PMC driver got fixed in order to work nicely in Xen
environment
- Intel Speed Select driver provides bucket vs core count relationship.
Besides that the tools has been updated for better output
- The PrivacyGuard is enabled on Lenovo ThinkPad laptops
- Three tablets - Trekstor Primebook C11B 2-in-1, Irbis TW90 and Chuwi
Surbook Mini - got touchscreen support
* tag 'platform-drivers-x86-v5.4-1' of git://git.infradead.org/linux-platform-drivers-x86: (53 commits)
MAINTAINERS: Switch PDx86 subsystem status to Odd Fixes
platform/x86: asus-wmi: Refactor charge threshold to use the battery hooking API
platform/x86: asus-wmi: Rename CHARGE_THRESHOLD to RSOC
platform/x86: asus-wmi: Reorder ASUS_WMI_CHARGE_THRESHOLD
tools/power/x86/intel-speed-select: Display core count for bucket
platform/x86: ISST: Allow additional TRL MSRs
tools/power/x86/intel-speed-select: Fix memory leak
tools/power/x86/intel-speed-select: Output success/failed for command output
tools/power/x86/intel-speed-select: Output human readable CPU list
tools/power/x86/intel-speed-select: Change turbo ratio output to maximum turbo frequency
tools/power/x86/intel-speed-select: Switch output to MHz
tools/power/x86/intel-speed-select: Simplify output for turbo-freq and base-freq
tools/power/x86/intel-speed-select: Fix cpu-count output
tools/power/x86/intel-speed-select: Fix help option typo
tools/power/x86/intel-speed-select: Fix package typo
tools/power/x86/intel-speed-select: Fix a read overflow in isst_set_tdp_level_msr()
platform/x86: intel_int0002_vgpio: Use device_init_wakeup
platform/x86: intel_int0002_vgpio: Fix wakeups not working on Cherry Trail
platform/x86: compal-laptop: Initialize "value" in ec_read_u8()
platform/x86: touchscreen_dmi: Add info for the Trekstor Primebook C11B 2-in-1
...
Read the bucket and core count relationship via MSR and display
when displaying turbo ratio limits.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This cpupower update for Linux 5.4-rc1 consists of bug fixes and
German translation updates from Benjamin Weis.
-----BEGIN PGP SIGNATURE-----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=AMIl
-----END PGP SIGNATURE-----
Merge tag 'linux-cpupower-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux
Pull cpupower utility updates for v5.4 from Shuah Khan:
"This cpupower update for Linux 5.4-rc1 consists of bug fixes and
German translation updates from Benjamin Weis."
* tag 'linux-cpupower-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux:
cpupower: update German translation
tools/power/cpupower: fix 64bit detection when cross-compiling
cpupower: Add missing newline at end of file
cpumasks are allocated by calling the alloc_cpu_mask() function and are
never free'd. They should be free'd after the commands have run.
Fix the memory leaks by calling free_cpu_set().
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: David Arcari <darcari@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The intel-speed-select tool currently only outputs a hexidecimal CPU mask,
which requires translation for use with kernel parameters such as
isolcpus.
Along with the CPU mask, output a human readable CPU list.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: David Arcari <darcari@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The intel-speed-select tool currently outputs the turbo ratio for every
bucket. Make the output more user-friendly by changing the output to the
maximum turbo frequency.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: David Arcari <darcari@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
These features are introduced on new processors that will never operate
in the KHz range.
Save some zeros and switch the output to MHz.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: David Arcari <darcari@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The current output of 'intel-speed-select -c 53 perf-profile info -l 0'
shows
speed-select-turbo-freq-support:1
speed-select-base-freq-support:1
speed-select-base-freq-enabled:0
speed-select-turbo-freq-enabled:0
Simplify the output to single lines displaying status of disabled,
enabled, and unsupported.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: David Arcari <darcari@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
I have a system with 28 threads/socket but intel-speed-select reports
a cpu-count of 29.
Fix an off-by-one error in the cpu_count() function.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: David Arcari <darcari@redhat.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The isst_send_msr_command() function will read 8 bytes but we are
passing an address to an int (4 bytes) so it results in a read overflow.
Fixes: 3fb4f7cd47 ("tools/power/x86: A tool to validate Intel Speed Select commands")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
sleepgraph:
- kprobe_events won't set correctly if the data is buffered
- force sysvals.setVal to be unbuffered and use binary mode
- tested in both python2 and python3
Link: https://bugzilla.kernel.org/show_bug.cgi?id=204773
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Conflicts:
tools/power/x86/turbostat/turbostat.c
Recent turbostat changes conflicted with a pending rename of x86 model names in tip:x86/cpu,
sort it out.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit 9392bd98bb ("tools/power turbostat: Add support for AMD
Fam 17h (Zen) RAPL") and the commit 3316f99a9f ("tools/power
turbostat: Also read package power on AMD F17h (Zen)") add AMD Fam 17h
RAPL support.
Hygon Family 18h(Dhyana) support RAPL in bit 14 of CPUID 0x80000007 EDX,
and has MSRs RAPL_PWR_UNIT/CORE_ENERGY_STAT/PKG_ENERGY_STAT. So add Hygon
Dhyana Family 18h support for RAPL.
Already tested on Hygon multi-node systems and it shows correct per-core
energy usage and the total package power.
Signed-off-by: Pu Wen <puwen@hygon.cn>
Reviewed-by: Calvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit 9392bd98bb ("tools/power turbostat: Add support for AMD
Fam 17h (Zen) RAPL") add a function get_tdp_amd(), the parameter is CPU
family. But the rapl_probe_amd() function use wrong model parameter.
Fix the wrong caller parameter of get_tdp_amd() to use family.
Cc: <stable@vger.kernel.org> # v5.1+
Signed-off-by: Pu Wen <puwen@hygon.cn>
Reviewed-by: Calvin Walton <calvin.walton@kepstin.ca>
Signed-off-by: Len Brown <len.brown@intel.com>
In some case C1% will be wrong value, when platform doesn't have MSR for
C1 residency.
For example:
Core CPU CPU%c1
- - 100.00
0 0 100.00
0 2 100.00
1 1 100.00
1 3 100.00
But adding Busy% will fix this
Core CPU Busy% CPU%c1
- - 99.77 0.23
0 0 99.77 0.23
0 2 99.77 0.23
1 1 99.77 0.23
1 3 99.77 0.23
This issue can be reproduced on most of the recent systems including
Broadwell, Skylake and later.
This is because if we don't select Busy% or Avg_MHz or Bzy_MHz then
mperf value will not be read from MSR, so it will be 0. But this
is required for C1% calculation when MSR for C1 residency is not present.
Same is true for C3, C6 and C7 column selection.
So add another define DO_BIC_READ(), which doesn't depend on user
column selection and use for mperf, C3, C6 and C7 related counters.
So when there is no platform support for C1 residency counters,
we still read these counters, if the CPU has support and user selected
display of CPU%c1.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Turbostat works by taking a snapshot of counters, sleeping, taking another
snapshot, calculating deltas, and printing out the table.
The sleep time is controlled via -i option or by user sending a signal or a
character to stdin. In the latter case, turbostat always adds 1 ms
sleep before it reads the counters, in order to avoid larger imprecisions
in the results in prints.
While the 1 ms delay may be a good idea for a "dumb" user, it is a
problem for an "aware" user. I do thousands and thousands of measurements
over a short period of time (like 2ms), and turbostat unconditionally adds
a 1ms to my interval, so I cannot get what I really need.
This patch removes the unconditional 1ms sleep. This is an expert user
tool, after all, and non-experts will unlikely ever use it in the non-fixed
interval mode anyway, so I think it is OK to remove the 1ms delay.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Commit '47936f944e78 tools/power turbostat: fix printing on input' make
a valid fix, but it completely disabled piped stdin support, which is
a valuable use-case. Indeed, if stdin is a pipe, turbostat won't read
anything from it, so it becomes impossible to get turbostat output at
user-defined moments, instead of the regular intervals.
There is no reason why this should works for terminals, but not for
pipes. This patch improves the situation. Instead of ignoring pipes, we
read data from them but gracefully handle the EOF case.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This enables turbostat utility on Ice Lake NNPI SoC.
Link: https://lkml.org/lkml/2019/6/5/1034
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Perhaps if this more descriptive name had been used,
then we wouldn't have had the HSW ULT vs HSW CORE bug,
fixed by the previous commit.
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat: cpu0: msr offset 0x630 read failed: Input/output error
because Haswell Core does not have C8-C10.
Output C8-C10 only on Haswell ULT.
Fixes: f5a4c76ad7 ("tools/power turbostat: consolidate duplicate model numbers")
Reported-by: Prarit Bhargava <prarit@redhat.com>
Suggested-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat could be terminated by general protection fault on some latest
hardwares which (for example) support 9 levels of C-states and show 18
"tADDED" lines. That bloats the total output and finally causes buffer
overrun. So let's extend the buffer to avoid this.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Currently the error return path does not close the file fp and leaks
a file descriptor. Fix this by closing the file.
Fixes: 5ea7647b33 ("tools/power turbostat: Warn on bad ACPI LPIT data")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Turbostat currently normalizes TSC and other values by dividing by an
interval. This interval is the delta between the start of one global
(all counters on all CPUs) sampling and the start of another. However,
this introduces a lot of jitter into the data.
In order to reduce jitter, the interval calculation should be based on
timestamps taken per thread and close to the start of the thread's
sampling.
Define a per thread time value to hold the delta between samples taken
on the thread.
Use the timestamp taken at the beginning of sampling to calculate the
delta.
Move the thread's beginning timestamp to after the CPU migration to
avoid jitter due to the migration.
Use the global time delta for the average time delta.
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The -w argument in x86_energy_perf_policy currently triggers an
unconditional segfault.
This is because the argument string reads: "+a:c:dD:E:e:f:m:M:rt:u:vw" and
yet the argument handler expects an argument.
When parse_optarg_string is called with a null argument, we then proceed to
crash in strncmp, not horribly friendly.
The man page describes -w as taking an argument, the long form
(--hwp-window) is correctly marked as taking a required argument, and the
code expects it.
As such, this patch simply marks the short form (-w) as requiring an
argument.
Signed-off-by: Zephaniah E. Loss-Cutler-Hull <zephaniah@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Compiling without optimisations is silly, especially since some
warnings depend on the optimiser. Use -O2.
Fortify adds warnings for unchecked I/O (among other things), which
seems to be a good idea for user-space code. Enable that too.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
x86_energy_perf_policy first uses __get_cpuid() to check the maximum
CPUID level and exits if it is too low. It then assumes that later
calls will succeed (which I think is architecturally guaranteed). It
also assumes that CPUID works at all (which is not guaranteed on
x86_32).
If optimisations are enabled, gcc warns about potentially
uninitialized variables. Fix this by adding an exit-on-error after
every call to __get_cpuid() instead of just checking the maximum
level.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Len Brown <len.brown@intel.com>
