We are assuming clocks enabled when calling rockchip_spi_remove, which
is not always true. Those clocks might already been disabled by the
runtime PM at that time.
Call pm_runtime_get_sync before trying to disable clocks to avoid that.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Slightly rework return value handling, no functional changes.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a bit more compact of_property_read_bool() calls instead of the
of_find_property() calls -- symmetrically with the of_property_read_u32()
calls already done in of_spi_parse_dt().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We still need to request/free GPIOs passed via the legacy path of
pxa2xx_spi_chip::gpio_cs, but we can use the gpiod API otherwise.
Consistently use the descriptor API instead of the legacy one.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MacBooks and MacBook Pros introduced since 2015 return empty _CRS data
for SPI slaves, causing device initialization to fail. Most of the
information that would normally be conveyed via _CRS is available
through ACPI device properties instead, so take advantage of them.
The meaning and appropriate usage of the device properties was reverse
engineered by Ronald Tschalär and carried over from these commits
authored by him:
https://github.com/cb22/macbook12-spi-driver/commit/9a416d699ef4https://github.com/cb22/macbook12-spi-driver/commit/0c34936ed9a1
According to Ronald, the device properties have the following meaning:
spiSclkPeriod /* period in ns */
spiWordSize /* in number of bits */
spiBitOrder /* 1 = MSB_FIRST, 0 = LSB_FIRST */
spiSPO /* clock polarity: 0 = low, 1 = high */
spiSPH /* clock phase: 0 = first, 1 = second */
spiCSDelay /* delay between cs and receive on reads in 10 us */
resetA2RUsec /* active-to-receive delay? */
resetRecUsec /* receive delay? */
Reported-by: Leif Liddy <leif.liddy@gmail.com>
Tested-by: Ronald Tschalär <ronald@innovation.ch>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
GPIO descriptors, when being requested, may configure pin at the same
time. In case of SPI chip select we shouldn't do any assumptions of the
state of pin since we don't know yet what chip is connected there and if
it uses high or low active state. So, leave the state of pin as is until
transfer will start.
Fixes: 99f499cd65 ("spi: pxa2xx: Add support for GPIO descriptor chip selects")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westeberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly added broadcom qspi driver in drivers/spi produces a build
warning when CONFIG_MTD is disabled:
include/linux/mtd/cfi.h:76:2: #warning No CONFIG_MTD_CFI_Ix selected. No NOR chip support can work. [-Werror=cpp]
There has been discussion on this in the link provided below. This fix in
SPI controller drivers implementing the ->spi_flash_read handler, now uses the
settings provided inside the 'struct spi_flash_read_message' parameter instead
of hardcoding them. Made changes to bcm_qspi_bspi_set_flex_mode() to set the BSPI
controller using the passed msg structure and remove the need to include
<linux/mtd/spi-nor.h> file by removing all use of SPINOR_OP_READ* macros.
Fixes: 4e3b2d236f ("spi: bcm-qspi: Add BSPI spi-nor flash controller driver")
Link: https://patchwork.kernel.org/patch/9624585/
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a valid case to call setup() following by setup_cs() several
times for the same chip.
With the commit
676a4e3bab ("spi: pxa2xx: Only claim CS GPIOs when the slave device is created")
it is not possible anymore due to GPIO line being requested already
during the first call to setup_cs().
For now, revert the commit to make things work again.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
add_uevent_var() can fail, let caller know about this.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To run spi-loopback-tests on HW without modifications, we need to
disable Chip Select. This should avoid surprising side effects for SPI devices
by testing patterns.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To run spi-loopback-tests on HW without modifications, we need to
disable Chip Select. This should avoid surprising side effects for
SPI devices by testing patterns.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistakes macros; fix EMPTY spellings:
RX_FIFO_EMTPY -> RX_FIFO_EMPTY
TX_FIFO_EMTPY -> TX_FIFO_EMPTY
Note that there are no other occurrances of these macros in the
source.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-spi@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Several module parameters are local to the source, so make them
static. Cleans up several sparse warnings such as:
"symbol 'loop_req' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Provide a module parameter to request internal loop by the SPI master
controller.
This should make loop testing easier without extra HW modification.
For test automation a logic analyzer is recommended for host
controller-independent verification.
An example test rig configuration and procedure:
i.MX6S RIoRBoard Logic Analyzer
-----------------------------------------
(J13 4) GND ------------- GND
(J13 6) CSPI3-CLK ------> PIN 3
(J13 8) CSPI3-MOSI <----- PIN 2
^ - internal loop configured by SPI_LOOP
| or can be user external jamper.
(J13 10) CSPI3-MISO -----> PIN 1
grab some data and decode it:
sigrok-cli -d fx2lafw --time 160000 --config samplerate=10m \
--channels 0-2 -o dump.sr
sigrok-cli -i dump.sr -P spi:mosi=1:clk=2 > result_for_regression_tests
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On R-Car Gen3 SoCs (excluding R-Car H3 ES1.x, which cannot be used for
SPI due to a hardware erratum), BRPS x BRDV = 1/1 is an invalid divider
setting.
Implement this limitation using an SoC/family-specific minimum divider.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Avoid hogging chip select GPIOs just because they are listed for the
master. They might be mulitplexed and, if no slave device is attached,
used for different purposes. Moreover, this strategy avoids having to
allocate a cs_gpiods structure.
Tested on the IOT2000 where the second SPI bus is connected to an
Arduino-compatible connector and multiplexed between SPI, GPIO and PWM
usage.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ECSPI contorller for iMX53 and iMX6 has few hardware issues
comparing to iMX51.
The change add possibility to detect which controller is used
to apply possible workaround and limitations.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Different ECSPI controller has different fifosize and DMA capability,
instead of calling functions to identify these information by check
devtype. add fifo_size and has_dmamode to spi_imx_devtype_data.
so that these information can be directly accessed.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the checkpatch.pl warnings on the driver
file.
Signed-off-by: Aravind Thokala <aravind.thk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the checkpatch.pl warnings on the driver
file.
Signed-off-by: Aravind Thokala <aravind.thk@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull spi uaccess delousing from Al Viro:
"Getting rid of pointless __get_user() and friends in drivers/spi.
[ the only reason it's on a separate branch is that I hoped it would
be picked by spi folks; looks like mail asking them to grab it got
lost and I hadn't followed up on that ]"
* 'for-spi' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
spidev: quit messing with access_ok()
Here, rx/tx allocation can fail. So avoid kvfree call
with NULL pointer.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in dev_info error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in dev_info message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the usage of rx_dma_desc and tx_dma_desc pointers
returned by dmaengine_prep_slave_sg, which can be null.
Detected by CoverityScan, CID#1446587 ("Dereference null return value")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch reworks DMA error management. In case the DMA callback is
called while EOT (End Of Transfer) flag is not set, that means that DMA
encountered an error. This error will result in an auto-suspend of SPI
flow, which could also result in an overrun. So, in DMA mode, SUSP and
OVR flags are a condition to stop the current transfer.
Moreover, stm32_spi_can_dma doesn't care about the state of dma channels.
During driver probe, master->can_dma is initialised if dma channel request
is successful. That's why we must use master->can_dma to know if dma
use is possible (dma channel are successfully requested and the transfer
size is greater than fifo size).
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch reworks suspend and resume callbacks and add runtime_suspend
and runtime_resume callbacks.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch replace ternary operator use by normal condition statements
to ease code reading.
It also removes redundant !!.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the optional dt property used to set master inter-data
idleness.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates of_device_id compatible string to fit with new
bindings.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rockchip spi would stop driving pins when runtime suspended, which
might break slave's xfer(for example cros_ec).
Since we have pullups on those pins, we only need to care about this
when the CS asserted.
So let's keep the spi alive when chip select is asserted.
Also use pm_runtime_put instead of pm_runtime_put_sync.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rockchip spi still requires slave selection when using GPIO CS.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch disables the use of the DMA for data transfer and forces the
use of PIO transfers instead as a quick fixup to solve the cache aliasing
issue on ARM9 based cores, which embeds a VIVT data cache.
Indeed in the case of VIVT data caches, it is not safe to call dma_map_*()
functions to map buffers for DMA transfers when those buffers have been
allocated by vmalloc() or from any DMA-unsafe area.
Further patches may propose a better solution based on the use of a bounce
buffer at the SPI sub-system level but such solution needs more time to be
discussed. Then the use of DMA transfers could be enabled again to improve
the performances but before that, this patch already solves the issue.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The error check of mbr < 0 is always false because mbr is a u32. Make
mbt an int so that a -ve error return from stm32_spi_prepare_mbr can be
detected.
Detected by CoverityScan, CID#1446586 ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The STM32 Serial Peripheral Interface (SPI) can be used to communicate
with external devices while using the specific synchronous protocol. It
supports a half-duplex, full-duplex and simplex synchronous, serial
communication with external devices with 4-bit to 16/32-bit per word. It
has two 8x/16x 8-bit embedded Rx and TxFIFOs with DMA capability. It can
operate in master or slave mode.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the checkpatch.pl warnings on the driver
file.
Signed-off-by: Aravind Thokala <aravind.thk@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of spi_alloc_master() failure it is better to return the
error immediately, so move the error check right after the allocation.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
this patch add support for mt2712 IC.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After failed to request dma tx chain, we need to disable pm_runtime.
Also cleanup error labels for better readability.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now struct spi_master is used for both SPI master and slave controllers,
it makes sense to rename it to struct spi_controller, and replace
"master" by "controller" where appropriate.
For now this conversion is done for SPI core infrastructure only.
Wrappers are provided for backwards compatibility, until all SPI drivers
have been converted.
Noteworthy details:
- SPI_MASTER_GPIO_SS is retained, as it only makes sense for SPI
master controllers,
- spi_busnum_to_master() is retained, as it looks up masters only,
- A new field spi_device.controller is added, but spi_device.master is
retained for compatibility (both are always initialized by
spi_alloc_device()),
- spi_flash_read() is used by SPI masters only.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't print the version at the beginning of atmel_spi_probe(). This avoids
spamming the log whenever a deferred probe runs.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Cannonlake LPSS SPI has up to four chip selects per port like in
Broxton and is clocked like Sunrisepoint and Kaby Lake. Add a new type
LPSS_CNL_SSP and configuration that enable runtime chip select detection
and use the same FIFO thresholds than in Sunrisepoint.
Patch adds support for both Cannonlake SoC and PCH.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
'bpw' is ambiguous and only the context makes sure if bytes_per_word
or bits_per_word is meant. Use the full names instead to make reading
the code easier.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We already have bits_per_word in the private driver struct and
bytes_per_word can be calculated from it, so remove bits_per_word.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's unnecessary to call spi_imx_dma_configure() from probe(). It will
be called later anyway again when an actual DMA transfer is prepared.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
struct spi_imx_config used to hold data specific to the current
transfer. However, other data is in the drivers private data struct.
Let's drop struct spi_imx_config and put the variables into the
drivers private data struct aswell.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
__spi_validate makes sure that every transfer has a valid bits_per_word
and speed_hz setting. We do not need to fallback to values from the
spi_device.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the spi_transfer given in spi_imx_setupxfer is NULL then
we have nothing to do. Bail out early in this case so that
we do not have to test for t != NULL multiple times later.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If CONFIG_OF is disable, it'll through compilation warning.
drivers/spi/spi-davinci.c: In function ‘spi_davinci_get_pdata’:
drivers/spi/spi-davinci.c:880:2: warning: return makes pointer from integer without a cast [enabled by default]
return -ENODEV;
drivers/spi/spi-davinci.c: In function ‘davinci_spi_probe’:
drivers/spi/spi-davinci.c:919:7: warning: assignment makes integer from pointer without a cast [enabled by default]
ret = spi_davinci_get_pdata(pdev, dspi);
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Changes in v2:
Add fix for both the warning.
Changes in v1:
It has fix for first warning.
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an example SPI slave handler to allow remote control of system
reboot, power off, halt, and suspend.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an example SPI slave handler responding with the uptime at the time
of reception of the last SPI message.
This can be used by an external microcontroller as a dead man's switch.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add slave mode support to the MSIOF driver, in both PIO and DMA mode.
For now this only supports the transmission of messages with a size
that is known in advance.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: Timeout handling cleanup, spi core integration, cancellation,
rewording]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for registering SPI slave controllers using the existing SPI
master framework:
- SPI slave controllers must use spi_alloc_slave() instead of
spi_alloc_master(), and should provide an additional callback
"slave_abort" to abort an ongoing SPI transfer request,
- SPI slave controllers are added to a new "spi_slave" device class,
- SPI slave handlers can be bound to the SPI slave device represented
by an SPI slave controller using a DT child node named "slave",
- Alternatively, (un)binding an SPI slave handler to the SPI slave
device represented by an SPI slave controller can be done by
(un)registering the slave device through a sysfs virtual file named
"slave".
From the point of view of an SPI slave protocol handler, an SPI slave
controller looks almost like an ordinary SPI master controller. The only
exception is that a transfer request will block on the remote SPI
master, and may be cancelled using spi_slave_abort().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove stray single spaces after a leading hard-tab.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Mark Brown <broonie@kernel.org>
The check to see if status is less than zero is actually redundant
as all previous places where it is -ve have already branched to the
exit paths, so it is never less than zero at the check.
Detected by CoverityScan, CID#1357119 ("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPICC hardware block on the Amlogic SoCs is Communication oriented and
can do Full-Duplex 8- to 32-bit width SPI transfers up to 30MHz.
The current driver only supportd the PIO transfer mode since the DMA seems
broken on available hardware.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some hardware designs use GPIOs to add (or supplement) the SPI
chip-select so that more than one SPI slave device can be used.
For this to work with the spi-orion driver the SPI_MASTER_GPIO_SS flag
needs to be set (because the other outputs are gated internally by the
CS) and the correct chip-select (in this case CS0) needs to be driven by
the controller.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Mark Brown <broonie@kernel.org>
This reverts commits 8d4a6cad7a and
179547e143.
Besides the problems already found with this patch it also modifies
the spi transfer tx_buf in spi_imx_u32_swap_u8() and spi_imx_u32_swap_u16().
This is hidden from the compiler with an explicit cast from const void*
to u32*, so no warning is issued.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Propagate error return from dspi_request_dma() into probe routine's
return.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case either transfer->tx_buf or transfer->rx_buf is NULL,
manipulation of buffer in spi_imx_u32_swap_u[8|16]() will cause
NULL pointer dereference crash.
Add buffer check at very beginning of spi_imx_u32_swap_u[8|16](),
to avoid such crash.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
previously burst length (BURST_LENGTH) is always set to equal
to bits_per_word, causes a 10us gap between each word in
transfer, which significantly affects performance.
This patch uses 32 bits transfer to simulate lower bits transfer,
and adjusts burst length runtimely to use biggeest burst length
as possible to reduce the gaps in transfer for PIO mode.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device table is required to load modules based on
modaliases. After adding MODULE_DEVICE_TABLE, below entries
for example will be added to module.alias:
alias: of:N*T*Cbrcm,bcm6328-hsspiC*
alias: of:N*T*Cbrcm,bcm6328-hsspi
Signed-off-by: Andres Galacho <andresgalacho@gmail.com>
Acked-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If NO_DMA=y:
ERROR: "bad_dma_ops" [drivers/spi/spi-ti-qspi.ko] undefined!
Add a dependency on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Octal permissions are preferred over symbolic permissions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use memdup_user() helper instead of open-coding to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This removes an unused completion from spidev_sync.
It was introduced in
commit 25d5cb4b03 ("spi: remove some spidev oops-on-rmmod paths")
and it was no longer used after:
commit 98d6f47958 ("spi: spidev: use spi_sync instead of spi_async")
Signed-off-by: Seraphime Kirkovski (Haapie) <kirkseraph@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for using GPIOs for chipselects as described by the
default dt-bindings.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implements consideration of the SPI_READY mode flag as
defined in spi.h. It extends the device tree bindings to support
the values defined by the reference manual for the DRCTL field.
Thus supporting edge-triggered and level-triggered bursts.
Signed-off-by: Leif Middelschulte <Leif.Middelschulte@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
trivial fix to spelling mistake in dbg_err messages
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Flash filesystems like JFFS2, UBIFS and MTD block layer can provide
vmalloc'd or kmap'd buffers that cannot be mapped using dma_map_sg() and
can potentially be in memory region above 32bit addressable region(ie
buffers belonging to memory region backed by LPAE) of DMA, implement
spi_flash_can_dma() interface to inform SPI core not to map such
buffers.
When buffers are not mapped for DMA, then use a pre allocated bounce
buffer(64K = typical flash erase sector size) to read from flash and
then do a copy to actual destination buffer. This is approach is much
faster than using memcpy using CPU and also reduces CPU load.
With this patch, UBIFS read speed is ~18MB/s and CPU utilization <20% on
DRA74 Rev H EVM. Performance degradation is negligible when compared
with non bounce buffer case while using UBIFS.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add an interface analogous to ->can_dma() for spi_flash_read()
interface. This will enable SPI controller drivers to inform SPI core
when not to do DMA mappings.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dw_mmio driver disables the block clock before unregistering
the host. The code unregistering the host may access the SPI block
registers. If register access happens with block clock disabled,
this may lead to a bus hang. Disable the clock after unregistering
the host to prevent such situation.
This bug was observed on Altera Cyclone V SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The generic SPI code calculates how long the issued transfer would take
and adds 100ms in addition to the timeout as tolerance. On my 500 MHz
Lantiq Mips SoC I am getting timeouts from the SPI like this when the
system boots up:
m25p80 spi32766.4: SPI transfer timed out
blk_update_request: I/O error, dev mtdblock3, sector 2
SQUASHFS error: squashfs_read_data failed to read block 0x6e
After increasing the tolerance for the timeout to 200ms I haven't seen
these SPI transfer time outs any more.
The Lantiq SPI driver in use here has an extra work queue in between,
which gets triggered when the controller send the last word and the
hardware FIFOs used for reading and writing are only 8 words long.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds deepest (Backup+Self-Refresh) PM support to the ATMEL SAMA5D2
SoC's SPI controller.
When resuming from deepest state, it is required to restore MR register
as the registers are lost since VDD core has been shut down when
entering deepest state on the SAMA5D2.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
