The OMAP mailbox driver is used by clients to communicate with remote
processors in general. The mailbox clients are expected to have stopped
communicating with these remote processors during a system suspend. The
OMAP mailbox fifos are expected to not have any messages as such. Add a
check for any pending unprocessed messages in the suspend callback, to
detect any communication protocol issues of the mailbox clients. The
system suspend is aborted if any messages are found.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Support has been added to the OMAP mailbox driver to allow it
to work across a system suspend/resume. The OMAP mailbox driver
requires only the interrupt configuration registers to be saved
and restored, and this is done in the suspend/resume callbacks.
The registers need to be saved only if there are active clients
at the time of suspend. The enabling and disabling of the mailbox
clocks is done automatically by the omap_device layer.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The interrupt type used for identifying the layout of the interrupt
configuration registers between OMAP4+ SoCs and older SoCs is stored
only in the sub-mailbox structures for easier access. Store this type
in the the omap_mbox_device structure as well along with the other
global variables. This is being done to facilitate the context save
and restore of appropriate registers during system suspend/resume.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Fix couple of checkpatch warnings of the type,
"WARNING: Missing a blank line after declarations"
Also, fixed a warning about a space after a typecast
while at this.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Remove the paragraph about writing to the Free Software
Foundation's mailing address from the GPL license header
as this address can change. This fixes the corresponding
checkpatch warning.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Fix the code formatting to use the kernel preferred style
of using the actual variables to determize the size using
the sizeof() operator. This fixes the corresponding checkpatch
warning as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
OMAP mailbox devices can no longer be created in legacy non-DT
mode, all the relevant code has been cleaned up. The OMAP mailbox
driver will only support devices created from DT going forward,
so drop the legacy platform device support from the driver.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Pull mailbox fixes from Jussi Brar:
"Misc fixes:
mailbox-test driver:
- prevent memory leak and another cosmetic change
mailbox:
- change the returned error code
Xgene driver:
- return -ENOMEM instead of PTR_ERR for failed devm_kzalloc"
* 'mailbox-devel' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Stop using ENOSYS for anything other than unimplemented syscalls
mailbox: mailbox-test: Prevent memory leak
mailbox: mailbox-test: Use more consistent format for calling copy_from_user()
mailbox: xgene-slimpro: Fix wrong test for devm_kzalloc
In accordance with e15f431fe2 ("errno.h: Improve ENOSYS's comment") and
91c9afaf97 ("checkpatch.pl: new instances of ENOSYS are errors") we're
converting from the old meaning of: ENOSYS "Function not implemented" to
a more standard EINVAL.
Reported-by: Seraphin Bonnaffe <seraphin.bonnaffe@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
If we set the Signal twice or more, without using it as part of a message,
memory will be re-allocated and the pointer over-written. Prevent this
potential leak by only allocating memory when there isn't any already.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
While we're at it, ensure copy-to location is NULL'ed in the error path.
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
* pm-cpufreq:
cpufreq: dt: Drop stale comment
cpufreq: intel_pstate: Documenation for structures
cpufreq: intel_pstate: fix inconsistency in setting policy limits
intel_pstate: Avoid extra invocation of intel_pstate_sample()
intel_pstate: Do not set utilization update hook too early
* pm-cpuidle:
intel_idle: Add KBL support
intel_idle: Add SKX support
intel_idle: Clean up all registered devices on exit.
intel_idle: Propagate hot plug errors.
intel_idle: Don't overreact to a cpuidle registration failure.
intel_idle: Setup the timer broadcast only on successful driver load.
intel_idle: Avoid a double free of the per-CPU data.
intel_idle: Fix dangling registration on error path.
intel_idle: Fix deallocation order on the driver exit path.
intel_idle: Remove redundant initialization calls.
intel_idle: Fix a helper function's return value.
intel_idle: remove useless return from void function.
* acpi-cppc:
mailbox: pcc: Don't access an unmapped memory address space
The acpi_pcc_probe() may end up accessing memory outside of the PCCT
table space causing the kernel panic(). Increment the pcct_entry
pointer after parsing 'HW-reduced Communications Subspace' to fix
the problem. This change also enables the parsing of subtable at
index 0.
Signed-off-by: Shanker Donthineni <shankerd@codeaurora.org>
Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull more mailbox updates from Jassi Brar:
"Device tree bindings and driver for TI's Message-Manager controller.
Due to some last minute cosmetic changes, the driver was not included
in the first pull request, otherwise the driver has been reviewed
twice"
* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Introduce TI message manager driver
Documentation: dt: mailbox: Add TI Message Manager
Support for TI Message Manager Module. This hardware block manages a
bunch of hardware queues meant for communication between processor
entities.
Clients sitting on top of this would manage the required protocol
for communicating with the counterpart entities.
For more details on TI Message Manager hardware block, see documentation
that will is available here: http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf
Chapter 8.1(Message Manager)
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The newly added rockchip mailbox driver causes a bug in
the ARM allyesconfig build because of a division of a resource_size_t
variable that may be 64 bit wide:
drivers/mailbox/built-in.o: In function `rockchip_mbox_probe':
:(.text+0x6614): undefined reference to `__aeabi_uldivmod'
This adds a cast to size_t, which turns it into a 32-bit division
in this case. This is safe because we know that we cannot possibly
map a resource that is longer than what a pointer contains, and
in practice it will be very short instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
* acpi-processor:
ACPI / sleep: move acpi_processor_sleep to sleep.c
ACPI / processor : add support for ACPI0010 processor container
ACPI / processor_idle: replace PREFIX with pr_fmt
* acpi-cppc:
ACPI / CPPC: use MRTT/MPAR to decide if/when a req can be sent
ACPI / CPPC: replace writeX/readX to PCC with relaxed version
mailbox: pcc: optimized pcc_send_data
ACPI / CPPC: optimized cpc_read and cpc_write
ACPI / CPPC: Optimize PCC Read Write operations
This driver is found on RK3368 SoCs.
The Mailbox module is a simple APB peripheral that allows both
the Cortex-A53 MCU system to communicate by writing operation to
generate interrupt.
The registers are accessible by both CPU via APB interface.
The Mailbox has the following main features:
1) Support dual-core system: Cortex-A53 and MCU.
2) Support APB interface.
3) Support four mailbox elements, each element includes one data word,
one command word register and one flag bit that can represent
one interrupt.
4) Four interrupts to Cortex-A53.
5) Four interrupts to MCU.
6) Provide 32 lock registers for software to use to indicate whether
mailbox is occupied.
[Jassi: Removed unused variable buf_base]
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
pcc_send_data() can be invoked during the execution of performance
critical code as in cppc_cpufreq driver. With acpi_* APIs, the
doorbell register accessed in pcc_send_data() if present in system
memory will be searched (in cached virt to phys addr mapping),
mapped, read/written and then unmapped. These operations take
significant amount of time.
This patch maps the performance critical doorbell register
during init and then reads/writes to it directly using the
mapped virtual address. This patch + similar changes to CPPC
acpi driver reduce the time per freq. transition from around
200us to about 20us for the CPPC cpufreq driver
Signed-off-by: Prashanth Prakash <pprakash@codeaurora.org>
Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
devm_ioremap() returns NULL, it never returns an ERR_PTR.
Fixes: f700e84f41 ('mailbox: Add support for APM X-Gene platform mailbox driver')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add driver for Hi6220 mailbox, the mailbox communicates with MCU; for
sending data, it can support two methods for low level implementation:
one is to use interrupt as acknowledge, another is automatic mode which
without any acknowledge. These two methods have been supported in the
driver. For receiving data, it will depend on the interrupt to notify
the channel has incoming message.
Now mailbox driver is used to send message to MCU to control dynamic
voltage and frequency scaling for CPU, GPU and DDR.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch adds support for different MMIO region for Tx and Rx paths.
If only one region is specified, it's assumed to be shared between Rx
and Tx, thereby retaining backward compatibility.
Also in order to support single channel dealing with both Tx and Rx with
dedicated MMIO regions, Tx channel itself is assigned to Rx if MMIO
regions are different and Rx is not specified.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reduce the logging from info to debug. Also use print_hex_dump_bytes
instead as it has support for dynamic printk providing options to
conditionally enable/disable these logs.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Underscores are usually forbidden in the compatible strings. So lets
remove it before the first users of this is seen.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This mailbox-test driver was designed to be generic, so let's remove ST
tag on it and make it generic.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Not every arch has io memory.
So, unbreak the build by fixing the dependencies.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch fixes the calculation of pcc_chan for non-zero id.
After the compiler ignores the (unsigned long) cast the
pcc_mbox_channels pointer is type-cast and then the type-cast
offset is added which results in address outside of the range
leading to the kernel crashing.
We might add braces and make it:
pcc_chan = (struct mbox_chan *)
((unsigned long) pcc_mbox_channels +
(id * sizeof(*pcc_chan)));
but let's go with array approach here and use id as index.
Tested on Juno board.
Signed-off-by: Alexey Klimov <alexey.klimov@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This mbox_chan_ops structure is never modified, so declare it as const,
like all the other mbox_chan_ops structures.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Don't pass mmio region as source to print_hex_dump() and then
again to memcpy_fromio(). Do it once and give print_hex_dump()
the buffer we just read the data in.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
We need to leave space for the NUL char.
Fixes: 8ea4484d0c ('mailbox: Add generic mechanism for testing Mailbox Controllers')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
The mailbox framework controls the transmission queue and requires
either its controller implementations or clients to run the state
machine for the Tx queue. The OMAP mailbox controller uses a Tx-ready
interrupt as the equivalent of a Tx-done interrupt to run this Tx
queue state-machine.
The WkupM3 processor on AM33xx and AM43xx SoCs is used to offload
certain PM tasks, like doing the necessary operations for Device
PM suspend/resume or for entering lower c-states during cpuidle.
The CPUIdle on AM33xx requires the messages to be sent without
having to trigger the Tx-ready interrupts, as the interrupt
would immediately terminate the CPUIdle operation. Support for
this has been added by introducing a DT quirk, "ti,mbox-send-noirq"
and using it to modify the normal OMAP mailbox controller behavior
on the sub-mailboxes used to communicate with the WkupM3 remote
processor. This also requires the wkup_m3_ipc driver to adjust
its mailbox usage logic to run the Tx state machine.
NOTE:
- AM43xx does not communicate with WkupM3 for CPU Idle, so is
not affected by this behavior. But, it uses the same IPC driver
for PM suspend/resume functionality, so requires the quirk as
well, because of changes to the common wkup_m3_ipc driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[s-anna@ti.com: revise logic and update comments/patch description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Kbuild test robot reported some Sparse warnings to the tune of:
sparse: incorrect type in argument 6 (different address spaces)
expected void const *buf
got void [noderef] <asn:2>*mmio
This was due to passing variables tagged with the Sparse cookie
'__iomem' through into memcpy() and print_hex_dump() without
adequate protection or casting. These issues were fixed in a
previous patch suppressing the warnings, but the issue is indeed
still present.
This patch fixes the warnings in the correct way, i.e. by using
the purposely authored memcpy_{from,to}io() derivatives in the
memcpy() case and casting the memory address to (void *) and
forcing Sparse to ignore to ignore it in the print_hex_dump()
case [NB: This is also what the memcpy() derivatives do].
Reported-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch deals with a few spelling, white space and type
warnings reported by Intel's Kbuild Test Robot.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This particular Client implementation uses shared memory in order
to pass messages between Mailbox users; however, it can be easily
hacked to support any type of Controller.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
ST's platforms currently support a maximum of 5 Mailboxes, one for
each of the supported co-processors situated on the platform. Each
Mailbox is divided up into 4 instances which consist of 32 channels.
Messages are passed between the application and co-processors using
shared memory areas. It is the Client's responsibility to manage
these areas.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
get_pcc_channel() does not return NULL on error it returns the error code
in ERR_PTR, but we have been checking it for NULL.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Pull mailbox updates from Jassi Brar:
"Mainly we move from jiffy based timer to HRTIMER for finer control
over polling. Then a controller reduces its polling period from 10 to
1ms"
* 'mailbox-for-next' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: arm_mhu: reduce txpoll_period from 10ms to 1 ms
mailbox: switch to hrtimer for tx_complete polling
mailbox: Drop owner assignment from platform_driver
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore,
Lv Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to
AML method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool
to be built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future
introduction of CPPC support and ACPI PCC mailbox driver
updates (Ashwin Chaugule).
- ACPI interrupts enumeration fix for a regression related
to the handling of IRQ attribute conflicts between MADT
and the ACPI namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael
J Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups
(Pan Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it
to preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support
for them in the OPP framework and in the cpufreq-dt driver plus
related OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=fTgI
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"From the number of commits perspective, the biggest items are ACPICA
and cpufreq changes with the latter taking the lead (over 50 commits).
On the cpufreq front, there are many cleanups and minor fixes in the
core and governors, driver updates etc. We also have a new cpufreq
driver for Mediatek MT8173 chips.
ACPICA mostly updates its debug infrastructure and adds a number of
fixes and cleanups for a good measure.
The Operating Performance Points (OPP) framework is updated with new
DT bindings and support for them among other things.
We have a few updates of the generic power domains framework and a
reorganization of the ACPI device enumeration code and bus type
operations.
And a lot of fixes and cleanups all over.
Included is one branch from the MFD tree as it contains some
PM-related driver core and ACPI PM changes a few other commits are
based on.
Specifics:
- ACPICA update to upstream revision 20150818 including method
tracing extensions to allow more in-depth AML debugging in the
kernel and a number of assorted fixes and cleanups (Bob Moore, Lv
Zheng, Markus Elfring).
- ACPI sysfs code updates and a documentation update related to AML
method tracing (Lv Zheng).
- ACPI EC driver fix related to serialized evaluations of _Qxx
methods and ACPI tools updates allowing the EC userspace tool to be
built from the kernel source (Lv Zheng).
- ACPI processor driver updates preparing it for future introduction
of CPPC support and ACPI PCC mailbox driver updates (Ashwin
Chaugule).
- ACPI interrupts enumeration fix for a regression related to the
handling of IRQ attribute conflicts between MADT and the ACPI
namespace (Jiang Liu).
- Fixes related to ACPI device PM (Mika Westerberg, Srinidhi
Kasagar).
- ACPI device registration code reorganization to separate the
sysfs-related code and bus type operations from the rest (Rafael J
Wysocki).
- Assorted cleanups in the ACPI core (Jarkko Nikula, Mathias Krause,
Andy Shevchenko, Rafael J Wysocki, Nicolas Iooss).
- ACPI cpufreq driver and ia64 cpufreq driver fixes and cleanups (Pan
Xinhui, Rafael J Wysocki).
- cpufreq core cleanups on top of the previous changes allowing it to
preseve its sysfs directories over system suspend/resume (Viresh
Kumar, Rafael J Wysocki, Sebastian Andrzej Siewior).
- cpufreq fixes and cleanups related to governors (Viresh Kumar).
- cpufreq updates (core and the cpufreq-dt driver) related to the
turbo/boost mode support (Viresh Kumar, Bartlomiej Zolnierkiewicz).
- New DT bindings for Operating Performance Points (OPP), support for
them in the OPP framework and in the cpufreq-dt driver plus related
OPP framework fixes and cleanups (Viresh Kumar).
- cpufreq powernv driver updates (Shilpasri G Bhat).
- New cpufreq driver for Mediatek MT8173 (Pi-Cheng Chen).
- Assorted cpufreq driver (speedstep-lib, sfi, integrator) cleanups
and fixes (Abhilash Jindal, Andrzej Hajda, Cristian Ardelean).
- intel_pstate driver updates including Skylake-S support, support
for enabling HW P-states per CPU and an additional vendor bypass
list entry (Kristen Carlson Accardi, Chen Yu, Ethan Zhao).
- cpuidle core fixes related to the handling of coupled idle states
(Xunlei Pang).
- intel_idle driver updates including Skylake Client support and
support for freeze-mode-specific idle states (Len Brown).
- Driver core updates related to power management (Andy Shevchenko,
Rafael J Wysocki).
- Generic power domains framework fixes and cleanups (Jon Hunter,
Geert Uytterhoeven, Rajendra Nayak, Ulf Hansson).
- Device PM QoS framework update to allow the latency tolerance
setting to be exposed to user space via sysfs (Mika Westerberg).
- devfreq support for PPMUv2 in Exynos5433 and a fix for an incorrect
exynos-ppmu DT binding (Chanwoo Choi, Javier Martinez Canillas).
- System sleep support updates (Alan Stern, Len Brown, SungEun Kim).
- rockchip-io AVS support updates (Heiko Stuebner).
- PM core clocks support fixup (Colin Ian King).
- Power capping RAPL driver update including support for Skylake H/S
and Broadwell-H (Radivoje Jovanovic, Seiichi Ikarashi).
- Generic device properties framework fixes related to the handling
of static (driver-provided) property sets (Andy Shevchenko).
- turbostat and cpupower updates (Len Brown, Shilpasri G Bhat,
Shreyas B Prabhu)"
* tag 'pm+acpi-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (180 commits)
cpufreq: speedstep-lib: Use monotonic clock
cpufreq: powernv: Increase the verbosity of OCC console messages
cpufreq: sfi: use kmemdup rather than duplicating its implementation
cpufreq: drop !cpufreq_driver check from cpufreq_parse_governor()
cpufreq: rename cpufreq_real_policy as cpufreq_user_policy
cpufreq: remove redundant 'policy' field from user_policy
cpufreq: remove redundant 'governor' field from user_policy
cpufreq: update user_policy.* on success
cpufreq: use memcpy() to copy policy
cpufreq: remove redundant CPUFREQ_INCOMPATIBLE notifier event
cpufreq: mediatek: Add MT8173 cpufreq driver
dt-bindings: mediatek: Add MT8173 CPU DVFS clock bindings
PM / Domains: Fix typo in description of genpd_dev_pm_detach()
PM / Domains: Remove unusable governor dummies
PM / Domains: Make pm_genpd_init() available to modules
PM / domains: Align column headers and data in pm_genpd_summary output
powercap / RAPL: disable the 2nd power limit properly
tools: cpupower: Fix error when running cpupower monitor
PM / OPP: Drop unlikely before IS_ERR(_OR_NULL)
PM / OPP: Fix static checker warning (broken 64bit big endian systems)
...
PCC is made selectable only by clients which use it. e.g. CPPC
Default it to disabled so that it is not included accidentally on
platforms which dont use it.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change initializes the PCC Mailbox earlier than
the ACPI processor driver. This enables drivers introduced
in follow up patches (e.g. CPPC) to be probed via the ACPI
processor driver interface. The CPPC probe requires the PCC
channel to be initialized for it to query each CPUs performance
capabilities.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Al Stone <al.stone@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since the mailbox core users hrtimers now, it can handle much higher
resolutions. We can reduce the txpoll_period to 1 ms as the transmit
usually takes just few microseconds.
Reported-and-suggested-by: Juri Lelli <Juri.Lelli@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The mailbox core uses jiffy based timer to handle polling for the
transmit completion. If the client/protocol have/support notification
of the last packet transmit completion via ACK packet, then we tick the
Tx state machine immediately in the callback. However if the client
doesn't support that mechanism we might end-up waiting for atleast a
jiffy even though the remote is ready to receive the next request.
This patch switches the timer used for that polling from jiffy-based
to hrtimer-based so that we can support polling at much higher time
resolution.
Reported-and-suggested-by: Juri Lelli <Juri.Lelli@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch fix spelling typo inv various part of sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KDJO
-----END PGP SIGNATURE-----
Merge tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part two from Paul Gortmaker:
"Replace module_init with appropriate alternate initcall in non
modules.
This series converts non-modular code that is using the module_init()
call to hook itself into the system to instead use one of our
alternate priority initcalls.
Unlike the previous series that used device_initcall and hence was a
runtime no-op, these commits change to one of the alternate initcalls,
because (a) we have them and (b) it seems like the right thing to do.
For example, it would seem logical to use arch_initcall for arch
specific setup code and fs_initcall for filesystem setup code.
This does mean however, that changes in the init ordering will be
taking place, and so there is a small risk that some kind of implicit
init ordering issue may lie uncovered. But I think it is still better
to give these ones sensible priorities than to just assign them all to
device_initcall in order to exactly preserve the old ordering.
Thad said, we have already made similar changes in core kernel code in
commit c96d6660dc ("kernel: audit/fix non-modular users of
module_init in core code") without any regressions reported, so this
type of change isn't without precedent. It has also got the same
local testing and linux-next coverage as all the other pull requests
that I'm sending for this merge window have got.
Once again, there is an unused module_exit function removal that shows
up as an outlier upon casual inspection of the diffstat"
* tag 'module_init-alternate_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
x86: perf_event_intel_pt.c: use arch_initcall to hook in enabling
x86: perf_event_intel_bts.c: use arch_initcall to hook in enabling
mm/page_owner.c: use late_initcall to hook in enabling
lib/list_sort: use late_initcall to hook in self tests
arm: use subsys_initcall in non-modular pl320 IPC code
powerpc: don't use module_init for non-modular core hugetlb code
powerpc: use subsys_initcall for Freescale Local Bus
x86: don't use module_init for non-modular core bootflag code
netfilter: don't use module_init/exit in core IPV4 code
fs/notify: don't use module_init for non-modular inotify_user code
mm: replace module_init usages with subsys_initcall in nommu.c
The drivers/mailbox/pl320-ipc.o is dependent on config PL320_MBOX
which is declared as a bool. Hence the code is never going to be
modular. So using module_init as an alias for __initcall can be
somewhat misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing. Also add an inclusion of init.h, as
that was previously implicit.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of subsys_initcall (which
seems to make sense for IPC code) will thus change this
registration from level 6-device to level 4-subsys (i.e. slightly
earlier). However no impact of that small difference is expected.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
With the VC reader blocked and the ARM writing, MAIL0_STA reads empty
permanently while MAIL1_STA goes from empty (0x40000000) to non-empty
(0x00000001-0x00000007) to full (0x80000008).
This bug ended up having no effect on us, because all of our
transactions in the client driver were synchronous and under a mutex.
Suggested-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch supplies a new framework API; mbox_request_channel_byname().
It works by supplying the usual client pointer as the first argument and
a string as the second. The API will search the client's node for a
'mbox-names' property then request a channel in the normal way using the
requested string's index as the expected second 'index' argument.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This mailbox driver provides a single mailbox channel to write 32-bit
values to the VPU and get a 32-bit response. The Raspberry Pi
firmware uses this mailbox channel to implement firmware calls, while
Roku 2 (despite being derived from the same firmware tree) doesn't.
The driver was originally submitted by Lubomir, based on the
out-of-tree 2708 mailbox driver. Eric Anholt fixed it up for
upstreaming, with the major functional change being that it now has no
notion of multiple channels (since that is a firmware-dependent
concept) and instead the raspberrypi-firmware driver will do that
bit-twiddling in its own messages.
[Jassi: made the 'mbox_chan_ops' struct as const and removed a redundant
variable]
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Craig McGeachie <slapdau@yahoo.com.au>
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
mbox_request_channel() currently returns EBUSY in the event the controller
is not present or if of_xlate() fails, but in neither case is EBUSY really
appropriate. Return EPROBE_DEFER if the controller is not yet present
and change of_xlate() to return an ERR_PTR instead of NULL so that the
error can be propagated back to the caller of mbox_request_channel().
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Acked-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The mailbox controller's channel ops ought to be read-only. Update
all the mailbox drivers to make their mbox_chan_ops const as well.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Cc: Ley Foon Tan <lftan@altera.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Not all architectures have io memory.
Fixes:
drivers/built-in.o: In function `altera_mbox_probe':
mailbox-altera.c:(.text+0x409fd2): undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add driver for the ARM Primecell Message-Handling-Unit(MHU) controller.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Vincent Yang <vincent.yang@socionext.com>
Signed-off-by: Tetsuya Nuriya <nuriya.tetsuya@socionext.com>
Previously the PCC driver depended on the client
side to map the communication space base address. This region
was was then used in the PCC driver and the client side.
The client side used this region to read and write its data
and the PCC driver used it to only write the PCC command.
Removing this split simplifies the PCC driver a lot. This patch
moves all communication region read/writes to the client side.
The PCC clients can now drive the PCC mailbox controller via the
mbox_client_txdone() method.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Pull mailbox framework updates from Jassi Brar.
* 'mailbox-devel' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Add Altera mailbox driver
mailbox: check for bit set before polling
Mailbox: Fix return value check in pcc_init()
The Altera mailbox allows for interprocessor communication. It supports
only one channel and work as either sender or receiver.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Before polling we just need to see if the TXDONE_BY_POLL bit
is set in txdone_method. There may be another bit (method)
specified as well, like TXDONE_BY_ACK.
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
In case of error, the function platform_create_bundle() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
pcc_init() uses pr_err() to print two messages that are really debug
and not interesting to users. Replace those pr_err() with pr_debug().
Reported-by: Cristian <caravena@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
ACPI 5.0+ spec defines a generic mode of communication
between the OS and a platform such as the BMC. This medium
(PCC) is typically used by CPPC (ACPI CPU Performance management),
RAS (ACPI reliability protocol) and MPST (ACPI Memory power
states).
This patch adds PCC support as a Mailbox Controller. As of
ACPI v5.1 there is no provision for clients to lookup mailbox
controllers in a way that Linux expects. e.g. in DT the clients
can list the mailboxes they can associate with in the DT binding
and then provide a unique index to lookup a channel within a mailbox.
Since the ACPI spec doesn't have anything similar, we introduce a
mailbox controller specific API so that when the client calls it,
we know to lookup in the context of a specific controller. This
also helps in keeping a consistent interface across DT and ACPI
for such drivers.
This patch implements basic PCC support using the ACPI v5.1
structures. IRQ mode support will be provided as follow up patches.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@linaro.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The OMAP mailbox driver and its existing clients (remoteproc
for OMAP4+) are adapted to use the generic mailbox framework.
The main changes for the adaptation are:
- The tasklet used for Tx is replaced with the state machine from
the generic mailbox framework. The workqueue used for processing
the received messages stays intact for minimizing the effects on
the OMAP mailbox clients.
- The existing exported client API, omap_mbox_get, omap_mbox_put and
omap_mbox_send_msg are deleted, as the framework provides equivalent
functionality. A OMAP-specific omap_mbox_request_channel is added
though to support non-DT way of requesting mailboxes.
- The OMAP mailbox driver is integrated with the mailbox framework
through the proper implementations of mbox_chan_ops, except for
.last_tx_done and .peek_data. The OMAP mailbox driver does not need
these ops, as it is completely interrupt driven.
- The OMAP mailbox driver uses a custom of_xlate controller ops that
allows phandles for the pargs specifier instead of indexing to avoid
any channel registration order dependencies.
- The new framework does not support multiple clients operating on a
single channel, so the reference counting logic is simplified.
- The remoteproc driver (current client) is adapted to use the new API.
The notifier callbacks used within this client is replaced with the
regular callbacks from the newer framework.
- The exported OMAP mailbox API are limited to omap_mbox_save_ctx,
omap_mbox_restore_ctx, omap_mbox_enable_irq & omap_mbox_disable_irq,
with the signature modified to take in the new mbox_chan handle instead
of the OMAP specific omap_mbox handle. The first 2 will be removed when
the OMAP mailbox driver is adapted to runtime_pm. The other exported
API omap_mbox_request_channel will be removed once existing legacy
users are converted to DT.
Signed-off-by: Suman Anna <s-anna@ti.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
If the mailbox controller expects the payload is in place before
initiating the transmit, then it's impossible to reuse the list
maintained by core mailbox code currently. Maintaining another list
for sending the message in the controller seems totally unnecessary
as core mailbox library already provides that feature.
This patch introduces tx_prepare callback in mbox_client which
can be used by the core mailbox library before initiating the
transaction through mbox->ops->send_data. The client driver can
implement this callback to ensure the payload is copied to the
shared memory.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
poll_txdone() will unconditionally re-arm the polling timer if there was
an active request, even if the active request completed and no other
requests were submitted. This is fixed by:
- only re-arming the timer if the controller reported that the current
transmission has not completed, and,
- moving the call to poll_txdone() into msg_submit() so that the
controller gets polled (and the timer re-armed, if necessary) whenever
a new message is submitted.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Pull mailbox framework from Jassi Brar:
"A framework for Mailbox controllers and clients have been cooking for
more than a year now.
Everybody in the CC list had been copied on patchset revisions and
most of them have made sounds of approval, though just one concrete
Reviewed-by. The patchset has also been in linux-next for a couple of
weeks now and no conflict has been reported. The framework has the
backing of at least 5 platforms, though I can't say if/when they
upstream their drivers (some businesses have 'changed')"
(Further acked-by by Arnd Bergmann and Suman Anna in the pull request
thread)
* 'mailbox-for-linus' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
dt: mailbox: add generic bindings
doc: add documentation for mailbox framework
mailbox: Introduce framework for mailbox
mailbox: rename pl320-ipc specific mailbox.h
Introduce common framework for client/protocol drivers and
controller drivers of Inter-Processor-Communication (IPC).
Client driver developers should have a look at
include/linux/mailbox_client.h to understand the part of
the API exposed to client drivers.
Similarly controller driver developers should have a look
at include/linux/mailbox_controller.h
Reviewed-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The patch 30058677 "ARM / highbank: add support for pl320 IPC"
added a pl320 IPC specific header file as a generic mailbox.h.
This file has been renamed appropriately to allow the
introduction of the generic mailbox API framework.
Acked-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Logic has been added to the OMAP2+ mailbox code to parse the
mailbox dt nodes and construct the different sub-mailboxes
associated with the instance. The DT representation of the
sub-mailbox devices is different from legacy platform data
representation to allow flexibility of interrupt configuration
between Tx and Rx fifos (to also possibly allow simplex devices
in the future). The DT representation gathers similar information
that was being passed previously through the platform data, except
for the interrupt type information, which is gathered through driver
compatible match data.
The non-DT support has to be maintained for now to not break
OMAP3 legacy boot, and the legacy-style code will be cleaned
up once OMAP3 is also converted to DT-boot only.
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A new structure, omap_mbox_device, is added to contain
the global variables pertinent to a mailbox h/w IP block.
This enables the support for having multiple instances of
the same h/w IP block in the SoC. This is in preparation
to support the DRA7 SoC, which is the first SoC in the OMAP
family to have multiple mailbox IP instances.
The changes include enhancements to the sub-mailbox registration
logic and mbox startup sequencing, removing the usage of single
global configuration variables for all h/w instances, and storing
the registered sub-mailboxes with the parent mailbox device
structure.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The structure omap_mbox_priv is used previously to store arch
specific (OMAP1 vs OMAP2+) data, and is no longer required to be
maintained separately. Instead, absorb its elements into either
the sub-mailbox device structure, omap_mbox, or the individual
fifo descriptor structure, omap_mbox_fifo.
The newmsg_bit and notfull_bit used on Rx and Tx fifos respectively
are represented by the new intr_bit field in the fifo descriptor
structure. The interrupt configuration registers are also moved
into the fifo descriptor structure to allow the Rx and Tx fifos
to use different interrupt lines/users.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no need for a separate common OMAP mailbox module
now that the OMAP1 mailbox driver has been removed. So,
consolidate the two individual OMAP mailbox modules into a
single driver. This streamlines the driver for converting
to mailbox framework.
The following are the main changes:
- collapse mailbox-omap2.c into omap-mailbox.c
- remove omap_mbox_ops and replace the ops calls with
the equivalent functionality.
- simplify the sub-mailbox startup/shutdown functionality,
the one-time operations are moved into probe, and the
pm_runtime_get_sync and pm_runtime_put_sync can be invoked
without using a configuration counter.
- move all definitions from private omap_mbox.h into the
source code, and eliminate this internal header.
- rename some variables that used the omap2_mbox prefix with
a generic omap_mbox prefix.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP mailbox IP has two different type of interrupt configuration
registers between OMAP4+ SoCs and OMAP2/3 SoCs. Simplify the current
interrupt configuration by using a single macro that translates the
two variants.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The type definition omap_mbox_type_t used for distinguishing
OMAP1 from OMAP2+ mailboxes is no longer needed after the
removal of OMAP1 mailbox driver, and has therefore been
cleaned up. This cleanup also eliminates the need for the
polling logic used for checking the transmit readiness.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are no existing users for OMAP1 mailbox driver
in kernel. Commit ab6f775 "Removing dead OMAP_DSP"
has cleaned up all the dead code related to the only
possible user, including the creation of the mailbox
platform device.
Remove this stale driver so that the OMAP mailbox
driver can be simplified and streamlined better for
converting to mailbox framework.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use the various devm_ interfaces to simplify the cleanup in
probe and remove functions in OMAP2+ mailbox driver.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is a bug in omap2_mbox_probe() where we try do:
mbox->irq = platform_get_irq(pdev, info->irq_id);
if (mbox->irq < 0) {
The problem is that mbox->irq is unsigned so the error handling doesn't
work. I've changed it to a signed integer.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Suman Anna <s-anna@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Omar Ramirez Luna <omar.ramirez@copitl.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The mailbox hardware (in OMAP) uses a queued mailbox interrupt
mechanism that provides a communication channel between processors
through a set of registers and their associated interrupt signals
by sending and receiving messages.
The OMAP mailbox framework/driver code is moved to be under
drivers/mailbox, in preparation for adapting to a common mailbox
driver framework. This allows the build for OMAP mailbox to be
enabled (it was disabled during the multi-platform support).
As part of the migration from plat and mach code:
- Kconfig symbols have been renamed to build OMAP1 or OMAP2+ drivers.
- mailbox.h under plat-omap/plat/include has been split into a public
and private header files. The public header has only the API related
functions and types.
- The module name mailbox.ko from plat-omap is changed to
omap-mailbox.ko
- The module name mailbox_mach.ko from mach-omapX is changed as
mailbox_omap1.ko for OMAP1
mailbox_omap2.ko for OMAP2+
Cc: Tony Lindgren <tony@atomide.com>
[gregkh@linuxfoundation.org: ack for staging part]
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Omar Ramirez Luna <omar.ramirez@copitl.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
The pl320 IPC allows for interprocessor communication between the
highbank A9 and the EnergyCore Management Engine. The pl320 implements
a straightforward mailbox protocol.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
