Add support for setting up GPIO pin interrupts in the lpc18xx pinctrl
driver. The LPC18xx SCU contain two registers that sets up the signal
routing to the GPIO pin interrupt (PINT) block. The routing uses the
GPIO namespace and not the pin namespace so a lookup is preformed on
the pin.
Routing configuration is done in the device tree by using the new
nxp,gpio-pin-interrupt property. This property takes single parameter
which sets the PINT hwirq for the GPIO.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The initialization of ngroups is occurring at the end of the
first iteration of the outer loop, which means that the
assignment pins[ngroups++] = i is potentially indexing into
a region outside of array pins because ngroups is not initialized.
Instead, initialize ngroups in the inner loop before the first
inner loop iteration.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw
spinlocks in IRQ handlers to play nice with the realtime
patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8,
PH1-Pro5, ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner
sun4i driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC
subdrivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4QFX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.3 development
cycle.
Like with GPIO it's a lot of stuff. If my subsystems are any sign of
the overall tempo of the kernel v4.3 will be a gigantic diff.
[ It looks like 4.3 is calmer than 4.2 in most other subsystems, but
we'll see - Linus ]
Core changes:
- It is possible configure groups in debugfs.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data(). This series was
created by Thomas Gleixner after the problem was observed by
Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx also wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
Driver feature enhancements:
- Power management support for the SiRF SoC Atlas 7.
- Power down support for the Qualcomm driver.
- Intel Cherryview and Baytrail: switch drivers to use raw spinlocks
in IRQ handlers to play nice with the realtime patch set.
- Rework and new modes handling for Qualcomm SPMI-MPP.
- Pinconf power source config for SH PFC.
New drivers and subdrivers:
- A new driver for Conexant Digicolor CX92755.
- A new driver for UniPhier PH1-LD4, PH1-Pro4, PH1-sLD8, PH1-Pro5,
ProXtream2 and PH1-LD6b SoC pin control support.
- Reverse-egineered the S/PDIF settings for the Allwinner sun4i
driver.
- Support for Qualcomm Technologies QDF2xxx ARM64 SoCs
- A new Freescale i.mx6ul subdriver.
Cleanup:
- Remove platform data support in a number of SH PFC subdrivers"
* tag 'pinctrl-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (95 commits)
pinctrl: at91: fix null pointer dereference
pinctrl: mediatek: Implement wake handler and suspend resume
pinctrl: mediatek: Fix multiple registration issue.
pinctrl: sh-pfc: r8a7794: add USB pin groups
pinctrl: at91: Use generic irq_{request,release}_resources()
pinctrl: cherryview: Use raw_spinlock for locking
pinctrl: baytrail: Use raw_spinlock for locking
pinctrl: imx6ul: Remove .owner field
pinctrl: zynq: Fix typos in smc0_nand_grp and smc0_nor_grp
pinctrl: sh-pfc: Implement pinconf power-source param for voltage switching
clk: rockchip: add pclk_pd_pmu to the list of rk3288 critical clocks
pinctrl: sun4i: add spdif to pin description.
pinctrl: atlas7: clear ugly branch statements for pull and drivestrength
pinctrl: baytrail: Serialize all register access
pinctrl: baytrail: Drop FSF mailing address
pinctrl: rockchip: only enable gpio clock when it setting
pinctrl/mediatek: fix spelling mistake in dev_err error message
pinctrl: cherryview: Serialize all register access
pinctrl: UniPhier: PH1-Pro5: add I2C ch6 pin-mux setting
pinctrl: nomadik: reflect current input value
...
The param_val variable is what determines if schmitt
trigger is enabled on a pin or not. A typo here mean
that schmitt trigger was always enabled for standard
and i2c pins.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The dedicated USB1 pins can be configured with pull-down and
for low power mode (suspend). Add support for this in the
pinctrl driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently, pinctrl_register() just returns NULL on error, so the
callers can not know the exact reason of the failure.
Some of the pinctrl drivers return -EINVAL, some -ENODEV, and some
-ENOMEM on error of pinctrl_register(), although the error code
might be different from the real cause of the error.
This commit reworks pinctrl_register() to return the appropriate
error code and modifies all of the pinctrl drivers to use IS_ERR()
for the error checking and PTR_ERR() for getting the error code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ray Jui <rjui@broadcom.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Hongzhou Yang <hongzhou.yang@mediatek.com>
Acked-by: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the required group function map and fill it at probe using
the pin capabilities information already present in the driver.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both pconf_get_pin and pconf_set_pin needs to lookup pin cap based
on the pin number. Create a common helper function that both
functions can use that also handles the case where no pin number is
found in the pins array.
This also fixes a small bug in pconf_get_pin where pconf_get_i2c0
would use the pins array index rather than the pin number.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pinctrl driver for the System Control Unit (SCU) found on NXP
LPC18xx/43xx devices.
Driver uses the generic pinctrl DT bindings for multiplexing
and property settings.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
