Add description for 'data' parameter and drop unused 'irq' memeber.
Here is the warnings:
drivers/i2c/busses/i2c-meson.c:103: warning: No description found for
parameter 'data'
drivers/i2c/busses/i2c-meson.c:103: warning: Excess struct member 'irq'
description in 'meson_i2c'
Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch try to add support for I2C controller in Meson-AXG SoC,
Due to the IP changes between I2C controller, we need to introduce
a compatible data to make the divider factor configurable.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The preceding changes in this patch series now allow to simplify
the interrupt handler significantly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
meson_i2c_write_tokens is always called directly after
meson_i2c_prepare_xfer (and only then). So we can simplify the code by
removing meson_i2c_write_tokens and moving the two statements of
meson_i2c_write_tokens to the end of meson_i2c_prepare_xfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We can directly add the stop token to the token chain including the
last transfer chunk. This is more efficient than creating a separate
token chain just for the stop command.
And it allows us to get rid of state STATE_STOP completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
If state is STATE_IDLE no interrupt should occur. Return IRQ_NONE
if such a spurious interrupt is detected.
Not having to take care of STATE_IDLE later in the interrupt handler
allows to further simplify the interrupt handler in subsequent
patches of this series.
In addition move resetting REG_CTRL_START bit to the start of the
interrupt handler to ensure that the start bit is always reset.
Currently the start bit is not reset for STATE_STOP because
i2c->state is set to STATE_IDLE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Variable count has always the same value as i, so we don't need it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The clock divider has 12 bits, splitted into a 10 bit field and a
2 bit field. The extra 2 bits aren't used currently.
Change this to use the full 12 bits and warn if the requested
frequency is too low.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
We don't have to parse the DT manually to retrieve the bus frequency
and we don't have to maintain an own default for the bus frequency.
Let the i2c core do this for us.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The bus frequency is fixed to what is set DT, therefore we can set
the clock divider in probe already and we don't have to set it for
each transfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Member irq can be replaced with a local variable in probe
because it's nowhere else accessed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Use min instead of min_t where min_t isn't needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The core will do this for us now.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().
The usage pattern of the completion is:
meson_i2c_xfer_msg()
reinit_completion()
...
/* Start the transfer */
...
wait_for_completion_timeout()
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This is a driver for the I2C controller found in Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
