We want to avoid forward-declarations of function if possible.
Rearrange the igc_clean_tx_ring function implementation.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for E822 devices
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Coverity reports some of the calls to xdp_rxq_info_reg() as potential
issues, because the driver does not check its return value. However,
those calls are wrapped with "if (!xdp_rxq_info_is_reg(&ring->xdp_rxq))"
and this check alone is enough to be sure that the function will never
fail.
All possible states of xdp_rxq_info are:
- NEW,
- REGISTERED,
- UNREGISTERED,
- UNUSED.
The driver won't mark a queue as UNUSED under no circumstance, so the
return value can be ignored safely.
Add comments for Coverity right above calls to xdp_rxq_info_reg() to
suppress the warnings.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ice_xsk_umem(), variable qid which is later used as an array index,
is not validated for a possible boundary exceedance. Because of that,
a calling function might receive an invalid address, which causes
general protection fault when dereferenced.
To address this, add a boundary check to see if qid is greater than the
size of a UMEM array. Also, don't let user change vsi->num_xsk_umems
just by trying to setup a second UMEM if its value is already set up
(i.e. UMEM region has already been allocated for this VSI).
While at it, make sure that ring->zca.free pointer is always zeroed out
if there is no UMEM on a specified ring.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the case where the hardware gives us a null Rx descriptor, it is
theoretically possible that we could call one of our skb-construction
functions with no data pointer, which would cause a panic.
In real life, this will never happen - we only get null RX
descriptors as the final descriptor in a chain of otherwise-valid
descriptors. When this happens, the skb will be extant and we'll just
call ice_add_rx_frag(), which can deal with empty data buffers.
Unfortunately, Coverity does not have intimate knowledge of our
hardware, so we must add a check here.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Coverity reports an error that is not really an error; suppress it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following the changes of commit 12299132b3 ("net: ethernet: intel: Demote
MTU change prints to debug"), change the MTU change message to netdev_dbg()
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently when there are SR-IOV VF(s) and the user does "ip link show <pf
interface>" the VF unicast MAC addresses all show 00:00:00:00:00:00
if the unicast MAC was set via VIRTCHNL (i.e. not administratively set
by the host PF).
This is misleading to the host administrator. Fix this by setting the
VF's dflt_lan_addr.addr when the VF's unicast MAC address is
configured via VIRTCHNL. There are a couple cases where we don't allow
the dflt_lan_addr.addr field to be written. First, If the VF's
pf_set_mac field is true and the VF is not trusted, then we don't allow
the dflt_lan_addr.addr to be modified. Second, if the
dflt_lan_addr.addr has already been set (i.e. via VIRTCHNL).
Also a small refactor was done to separate the flow for add and delete
MAC addresses in order to simplify the logic for error conditions
and set/clear the VF's dflt_lan_addr.addr field.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the flow for ice_set_vf_link_state() is not configuring link
the same as all other VF link configuration flows. Fix this by only
setting the necessary VF members in ice_set_vf_link_state() and then
call ice_vc_notify_link_state() to actually configure link for the
VF. This made ice_set_pfe_link_forced() unnecessary, so it was
deleted. Also, this commonizes the link flows for the VF to all call
ice_vc_notify_link_state().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove Rx flex descriptor metadata and flag programming; per specification
these registers cannot be written to as they are read only.
Signed-off-by: Vignesh Sridhar <vignesh.sridhar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for all unused parameters, if ethtool sent one of them,
print info about that and return error.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After each rebuild driver deallocates q_vectors, so the interrupt
throttle rate (ITR) settings get lost.
Create a function to save and restore ITR for each queue. If a user
increases the number of queues, restore all the previous queue
settings for each existing queue, and the additional queues will
get the default setting.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the user sets itr_setting to zero from ethtool -C, the driver changes
this value to default in ice_cfg_itr (for example after changing ring
param). Remove code that sets default value in ice_cfg_itr and move it to
place where the driver allocates q_vectors.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we do "for (i = 0; i < pf->num_alloc_vfs; i++)" all over the
place. Many other places use macros to contain this repeated for loop,
So create the macro ice_for_each_vf(pf, i) that does the same thing.
There were a couple places we were using one loop variable and a VF
iterator, which were changed to using a local variable within the
ice_for_each_vf() macro.
Also in ice_alloc_vfs() we were setting pf->num_alloc_vfs after doing
"for (i = 0; i < num_alloc_vfs; i++)". Instead assign pf->num_alloc_vfs
right after allocating memory for the pf->vf array.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We can't have more than one default VSI so prevent another VSI from
overwriting the current dflt_vsi. This was achieved by adding the
following functions:
ice_is_dflt_vsi_in_use()
- Used to check if the default VSI is already being used.
ice_is_vsi_dflt_vsi()
- Used to check if VSI passed in is in fact the default VSI.
ice_set_dflt_vsi()
- Used to set the default VSI via a switch rule
ice_clear_dflt_vsi()
- Used to clear the default VSI via a switch rule.
Also, there was no need to introduce any locking because all mailbox
events and synchronization of switch filters for the PF happen in the
service task.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are many things wrong with the function
ice_set_vf_spoofchk().
1. The VSI being modified is the PF VSI, not the VF VSI.
2. We are enabling Rx VLAN pruning instead of Tx VLAN anti-spoof.
3. The spoofchk setting for each VF is not initialized correctly
or re-initialized correctly on reset.
To fix [1] we need to make sure we are modifying the VF VSI.
This is done by using the vf->lan_vsi_idx to index into the PF's
VSI array.
To fix [2] replace setting Rx VLAN pruning in ice_set_vf_spoofchk()
with setting Tx VLAN anti-spoof.
To Fix [3] we need to make sure the initial VSI settings match what
is done in ice_set_vf_spoofchk() for spoofchk=on. Also make sure
this also works for VF reset. This was done by modifying ice_vsi_init()
to account for the current spoofchk state of the VF VSI.
Because of these changes, Tx VLAN anti-spoof needs to be removed
from ice_cfg_vlan_pruning(). This is okay for the VF because this
is now controlled from the admin enabling/disabling spoofchk. For the
PF, Tx VLAN anti-spoof should not be set. This change requires us to
call ice_set_vf_spoofchk() when configuring promiscuous mode for
the VF which requires ice_set_vf_spoofchk() to move in order to prevent
a forward declaration prototype.
Also, add VLAN 0 by default when allocating a VF since the PF is unaware
if the guest OS is running the 8021q module. Without this, MDD events will
trigger on untagged traffic because spoofcheck is enabled by default. Due
to this change, ignore add/delete messages for VLAN 0 from VIRTCHNL since
this is added/deleted during VF initialization/teardown respectively and
should not be modified.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the work done by Alex Duyck on other Intel drivers, add code to
support UDP segmentation offload (USO) for the ice driver.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
drivers/net/ethernet/brocade/bna/bfa_ioc.c: In function
‘bfa_ioc_fwver_clear’:
drivers/net/ethernet/brocade/bna/bfa_ioc.c:1127:13: warning: variable
‘pgoff’ set but not used [-Wunused-but-set-variable]
It is never used, and so can be removed.
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver only exists on a non NUMA aware machine.
With 44768decb7 ("page_pool: handle page recycle for NUMA_NO_NODE condition")
applied we can safely change that to NUMA_NO_NODE and accommodate future
NUMA aware hardware using netsec network interface
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ENETC implement time specific departure capability, which enables
the user to specify when a frame can be transmitted. When this
capability is enabled, the device will delay the transmission of
the frame so that it can be transmitted at the precisely specified time.
The delay departure time up to 0.5 seconds in the future. If the
departure time in the transmit BD has not yet been reached, based
on the current time, the packet will not be transmitted.
This driver was loaded by Qos driver ETF. User could load it by tc
commands. Here are the example commands:
tc qdisc add dev eth0 root handle 1: mqprio \
num_tc 8 map 0 1 2 3 4 5 6 7 hw 1
tc qdisc replace dev eth0 parent 1:8 etf \
clockid CLOCK_TAI delta 30000 offload
These example try to set queue mapping first and then set queue 7
with 30us ahead dequeue time.
Then user send test frame should set SO_TXTIME feature for socket.
There are also some limitations for this feature in hardware:
- Transmit checksum offloads and time specific departure operation
are mutually exclusive.
- Time Aware Shaper feature (Qbv) offload and time specific departure
operation are mutually exclusive.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use resource_size rather than a verbose computation on
the end and start fields.
The semantic patch that makes these changes is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@ struct resource ptr; @@
- (ptr.end + 1 - ptr.start)
+ resource_size(&ptr)
@@ struct resource *ptr; @@
- (ptr->end + 1 - ptr->start)
+ resource_size(ptr)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the SFC4000 code, now moved to sfc-falcon, needed I2C.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When APP TLV selector 1 (EtherType) is used with PID of 0, the
corresponding entry specifies "default application priority [...] when
application priority is not otherwise specified."
mlxsw currently supports this type of APP entry, but uses it only as a
fallback for unspecified DSCP rules. However non-IP traffic is prioritized
according to port-default priority, not according to the DSCP-to-prio
tables, and thus it's currently not possible to prioritize such traffic
correctly.
Extend the use of the abovementioned APP entry to also set default port
priority.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add QPDP. This register controls the port default Switch Priority and
Color. The default Switch Priority and Color are used for frames where the
trust state uses default values. Currently there are two cases where this
applies: a port is in trust-PCP state, but a packet arrives untagged; and a
port is in trust-DSCP state, but a non-IP packet arrives.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
1GbE Intel Wired LAN Driver Updates 2019-12-31
This series contains updates to e1000e, igb and igc only.
Robert Beckett provide an igb change to assist in keeping packets from
being dropped due to receive descriptor ring being full when receive
flow control is enabled. Create a separate function to setup SRRCTL to
ease in reuse and ensure that setting of the drop enable bit only if
receive flow control is not enabled.
Sasha adds support for scatter gather support in igc. Improve the
direct memory address mapping flow by optimizing/simplifying and more
clear. Update igc to use pci_release_mem_regions() instead of
pci_release_selected_regions(). Clean up function header comments to
align with the actual code. Adds support for 64 bit DMA access, to help
handle socket buffer fragments in high memory. Adds legacy power
management support in igc by implementing suspend, resume,
runtime_suspend/resume, and runtime_idle callbacks. Clean up references
to Serdes interface in igc since that interface is not supported for
i225 devices.
Alex replaces the pr_info calls with netdev_info in all cases related to
netdev link state, as suggested by Joe Perches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Serdes interface is not applicable for i225 devices.
Remove this from comments and make comments more clearly.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the pr_info calls with netdev_info in all cases related to the
netdevice link state.
As a result of this patch the link messages will change as shown below.
Before:
e1000e: ens3 NIC Link is Down
e1000e: ens3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
After:
e1000e 0000:00:03.0 ens3: NIC Link is Down
e1000e 0000:00:03.0 ens3: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On relevant platforms ndo_start_xmit can handle socket buffer
fragments in high memory
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function description for igc_alloc_rx_buffers has not reflected
the function meaning. Add meaningful description.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function description for igc_is_non_eop includes an extra @skb
parameter description. This parameter doesn't exist on the function, so
remove it.
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the pci_release_mem_regions method instead of the
pci_release_selected_regions method
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Improve the probe flow and set both the DMA mask and the coherent
to the same thing. Make the flow optimized and cleared.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Scatter gather is used to do DMA data transfers of data that is written to
noncontiguous areas of memory.
This patch enables scatter gather support.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If Rx flow control has been enabled (via autoneg or forced), packets
should not be dropped due to Rx descriptor ring exhaustion. Instead
pause frames should be used to apply back pressure. This only applies
if VFs are not in use.
Move SRRCTL setup to its own function for easy reuse and only set drop
enable bit if Rx flow control is not enabled.
Since v1: always enable dropping of packets if VFs in use.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When disabling PTP timestamping, don't reset the switch with the new
static config until all existing PTP frames have been timestamped on the
RX path or dropped. There's nothing we can do with these afterwards.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And move the queue of skb's waiting for RX timestamps into the ptp_data
structure, since it isn't needed if PTP is not compiled.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c ("net: dsa: sja1105: Reverse TPID and TPID2")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check originates from the initial implementation which was not based
on PTP time but on a standalone clock source. In the meantime we can now
program the PTPSCHTM register at runtime with the dynamic base time
(actually with a value that is 200 ns smaller, to avoid writing DELTA=0
in the Schedule Entry Points Parameters Table). And we also have logic
for moving the actual base time in the future of the PHC's current time
base, so the check for zero serves no purpose, since even if the user
will specify zero, that's not what will end up in the static config
table where the limitation is.
Fixes: 86db36a347 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When activating tc-taprio offload on the switch ports, the TAS state
machine will try to check whether it is running or not, but will find
both the STARTED and STOPPED bits as false in the
sja1105_tas_check_running function. So the function will return -EINVAL
(an abnormal situation) and the kernel will keep printing this from the
TAS FSM workqueue:
[ 37.691971] sja1105 spi0.1: An operation returned -22
The reason is that the underlying function that gets called,
sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So
the command buffer remains initialized with zeroes instead of retrieving
the hardware state. Fix that.
Fixes: 41603d78b3 ("net: dsa: sja1105: Make the PTP command read-write")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP egress timestamp N must be captured from register PTPEGR_TS[n],
where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per
port. We are only using TSREG=0.
As opposed to the management slots, which are 4 in number
(SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which
includes PTP frames) can be sent to any non-CPU port through any
management slot. When the CPU port is not the last port (#4), there will
be a mismatch between the slot and the port number.
Luckily, the only mainline occurrence with this switch
(arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the
issue did not manifest itself thus far.
Fixes: 47ed985e97 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'eth_zero_addr()' is already called in the error handling path. This is
harmless, but there is no point in calling it twice, so remove one.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
[1] https://standards.ieee.org/standard/802_3-2005.html
Fixes: c3168cabe1 ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.
Fix this by using a dedicated policer for VRRP packets.
Fixes: 11566d34f8 ("mlxsw: spectrum: Add VRRP traps")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a router interface (RIF) is created the MAC address of the backing
netdev is verified to have the same MSBs as existing RIFs. This is
required in order to avoid changing existing RIF MAC addresses that all
share the same MSBs.
Loopback RIFs are special in this regard as they do not have a MAC
address, given they are only used to loop packets from the overlay to
the underlay.
Without this change, an error is returned when trying to create a RIF
after the creation of a GRE tunnel that is represented by a loopback
RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which
does not share the same MSBs as physical interfaces. Adding an IP
address to any physical interface results in:
Error: mlxsw_spectrum: All router interface MAC addresses must have the
same prefix.
Fix this by skipping loopback RIFs during MAC validation.
Fixes: 74bc993974 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver wrongly assumes that it is the only entity that can set the
SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the
gfar_clean_tx_ring function, where the TX timestamp is collected if
necessary, the aforementioned bit is used to discriminate whether or not
the TX timestamp should be delivered to the socket's error queue.
But a stacked driver such as a DSA switch can also set the
SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in
order to denote that the hardware timestamping process is undergoing.
Therefore, gianfar would misinterpret the "in progress" bit as being its
own, and deliver a second skb clone in the socket's error queue,
completely throwing off a PTP process which is not expecting to receive
it, _even though_ TX timestamping is not enabled for gianfar.
There have been discussions [0] as to whether non-MAC drivers need or
not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2
timestamps, a sw and a hw one, to applications which only expect one).
But as of this patch, there are at least 2 PTP drivers that would break
in conjunction with gianfar: the sja1105 DSA switch and the felix
switch, by way of its ocelot core driver.
So regardless of that conclusion, fix the gianfar driver to not do stuff
based on flags set by others and not intended for it.
[0]: https://www.spinics.net/lists/netdev/msg619699.html
Fixes: f0ee7acfcd ("gianfar: Add hardware TX timestamping support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wan/fsl_ucc_hdlc.c: In function ucc_hdlc_irq_handler:
drivers/net/wan/fsl_ucc_hdlc.c:643:23:
warning: variable ut_info set but not used [-Wunused-but-set-variable]
drivers/net/wan/fsl_ucc_hdlc.c: In function uhdlc_suspend:
drivers/net/wan/fsl_ucc_hdlc.c:880:23:
warning: variable ut_info set but not used [-Wunused-but-set-variable]
drivers/net/wan/fsl_ucc_hdlc.c: In function uhdlc_resume:
drivers/net/wan/fsl_ucc_hdlc.c:925:6:
warning: variable ret set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
