For TC classes, their ->get() and ->put() are always paired, and the
reference counting is completely useless, because:
1) For class modification and dumping paths, we already hold RTNL lock,
so all of these ->get(),->change(),->put() are atomic.
2) For filter bindiing/unbinding, we use other reference counter than
this one, and they should have RTNL lock too.
3) For ->qlen_notify(), it is special because it is called on ->enqueue()
path, but we already hold qdisc tree lock there, and we hold this
tree lock when graft or delete the class too, so it should not be gone
or changed until we release the tree lock.
Therefore, this patch removes ->get() and ->put(), but:
1) Adds a new ->find() to find the pointer to a class by classid, no
refcnt.
2) Move the original class destroy upon the last refcnt into ->delete(),
right after releasing tree lock. This is fine because the class is
already removed from hash when holding the lock.
For those who also use ->put() as ->unbind(), just rename them to reflect
this change.
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like for TC actions, ->delete() is a special case,
we have to prepare and fill the notification before delete
otherwise would get use-after-free after we remove the
reference count.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not needed if we move them up properly.
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the following seg6local actions.
- SEG6_LOCAL_ACTION_END_T: regular SRH processing and forward to the
next-hop looked up in the specified routing table.
- SEG6_LOCAL_ACTION_END_DX2: decapsulate an L2 frame and forward it to
the specified network interface.
- SEG6_LOCAL_ACTION_END_DX4: decapsulate an IPv4 packet and forward it,
possibly to the specified next-hop.
- SEG6_LOCAL_ACTION_END_DT6: decapsulate an IPv6 packet and forward it
to the next-hop looked up in the specified routing table.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds three helper functions to be used with the seg6local packet
processing actions.
The decap_and_validate() function will be used by the End.D* actions, that
decapsulate an SR-enabled packet.
The advance_nextseg() function applies the fundamental operations to update
an SRH for the next segment.
The lookup_nexthop() function helps select the next-hop for the processed
SR packets. It supports an optional next-hop address to route the packet
specifically through it, and an optional routing table to use.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that the seg6local lightweight tunnel is used solely
with IPv6 routes and processes only IPv6 packets.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the L2 frame encapsulation mechanism, referred to
as T.Encaps.L2 in the SRv6 specifications [1].
A new type of SRv6 tunnel mode is added (SEG6_IPTUN_MODE_L2ENCAP). It only
accepts packets with an existing MAC header (i.e., it will not work for
locally generated packets). The resulting packet looks like IPv6 -> SRH ->
Ethernet -> original L3 payload. The next header field of the SRH is set to
NEXTHDR_NONE.
[1] https://tools.ietf.org/html/draft-filsfils-spring-srv6-network-programming-01
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the SRv6 encapsulation mode to carry an IPv4 payload.
All the infrastructure was already present, I just had to add a parameter
to seg6_do_srh_encap() to specify the inner packet protocol, and perform
some additional checks.
Usage example:
ip route add 1.2.3.4 encap seg6 mode encap segs fc00::1,fc00::2 dev eth0
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow our callers to influence the choice of ECMP link by honoring the
hash passed together with the flow info. This allows for special
treatment of ICMP errors which we would like to route over the same path
as the IPv6 datagram that triggered the error.
Also go through rt6_multipath_hash(), in the usual case when we aren't
dealing with an ICMP error, so that there is one central place where
multipath hash is computed.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 644d0e6569 ("ipv6 Use get_hash_from_flowi6 for rt6 hash") has
turned rt6_info_hash_nhsfn() into a one-liner, so it no longer makes
sense to keep it around. Also remove the accompanying comment that has
become outdated.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forwarding or sending out an ICMPv6 error, look at the embedded
packet that triggered the error and compute a flow hash over its
headers.
This let's us route the ICMP error together with the flow it belongs to
when multipath (ECMP) routing is in use, which in turn makes Path MTU
Discovery work in ECMP load-balanced or anycast setups (RFC 7690).
Granted, end-hosts behind the ECMP router (aka servers) need to reflect
the IPv6 Flow Label for PMTUD to work.
The code is organized to be in parallel with ipv4 stack:
ip_multipath_l3_keys -> ip6_multipath_l3_keys
fib_multipath_hash -> rt6_multipath_hash
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reflecting IPv6 Flow Label at server nodes is useful in environments
that employ multipath routing to load balance the requests. As "IPv6
Flow Label Reflection" standard draft [1] points out - ICMPv6 PTB error
messages generated in response to a downstream packets from the server
can be routed by a load balancer back to the original server without
looking at transport headers, if the server applies the flow label
reflection. This enables the Path MTU Discovery past the ECMP router in
load-balance or anycast environments where each server node is reachable
by only one path.
Introduce a sysctl to enable flow label reflection per net namespace for
all newly created sockets. Same could be earlier achieved only per
socket by setting the IPV6_FL_F_REFLECT flag for the IPV6_FLOWLABEL_MGR
socket option.
[1] https://tools.ietf.org/html/draft-wang-6man-flow-label-reflection-01
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is too much overhead in the current trace_xdp_redirect
tracepoint as it does strcpy and strlen on the net_device names.
Besides, exposing the ifindex/index is actually the information that
is needed in the tracepoint to diagnose issues. When a lookup fails
(either ifindex or devmap index) then there is a need for saying which
to_index that have issues.
V2: Adjust args to be aligned with trace_xdp_exception.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the xdp_do_generic_redirect() call fails, it trigger the
trace_xdp_exception tracepoint. It seems better to use the same
tracepoint trace_xdp_redirect, as the native xdp_do_redirect{,_map} does.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Given there is a tracepoint that can track the error code
of xdp_do_redirect calls, the WARN_ONCE in bpf_warn_invalid_xdp_redirect
doesn't seem relevant any longer. Simply remove the function.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The entry clear routine can be shared between the drivers, thus it is
moved inside devlink.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the dpipe table's size was static and known at registration
time. The host table does not have constant size and it is resized in
dynamic manner. In order to support this behavior the size is changed
to be obtained dynamically via an op.
This patch also adjust the current dpipe table for the new API.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the IPv4 host table which will be introduced in the
following patches. This header is global and can be reused by many
drivers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used by the IPv4 host table which will be introduced in the
following patches. This header is global and can be reused by many
drivers.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iph is being assigned the same value twice; remove the redundant
first assignment. (Thanks to Nikolay Aleksandrov for pointing out
that the first asssignment should be removed and not the second)
Fixes warning:
net/ipv4/ip_gre.c:265:2: warning: Value stored to 'iph' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genl_ops are not supposed to change at runtime. All functions
working with genl_ops provided by <net/genetlink.h> work with
const genl_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary to allow the user to disable peeking with
offset once it's enabled.
Unix sockets already allow the above, with this patch we
permit it for udp[6] sockets, too.
Fixes: 627d2d6b55 ("udp: enable MSG_PEEK at non-zero offset")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when ipv4 route inserts a fib_info, it memcmp fib_metrics.
It means ipv4 route identifies one route also with metrics.
But when removing a route, it tries to find the route without
caring about the metrics. It will cause that the route with
right metrics can't be removed.
Thomas noticed this issue when doing the testing:
1. add:
# ip route append 192.168.7.0/24 dev v window 1000
# ip route append 192.168.7.0/24 dev v window 1001
# ip route append 192.168.7.0/24 dev v window 1002
# ip route append 192.168.7.0/24 dev v window 1003
2. delete:
# ip route delete 192.168.7.0/24 dev v window 1002
3. show:
192.168.7.0/24 proto boot scope link window 1001
192.168.7.0/24 proto boot scope link window 1002
192.168.7.0/24 proto boot scope link window 1003
The one with window 1002 wasn't deleted but the first one was.
This patch is to do metrics match when looking up and deleting
one route.
Reported-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SOF_TIMESTAMPING_RX_SOFTWARE is enabled for tcp sockets, return the
timestamp corresponding to the highest sequence number data returned.
Previously the skb->tstamp is overwritten when a TCP packet is placed
in the out of order queue. While the packet is in the ooo queue, save the
timestamp in the TCB_SKB_CB. This space is shared with the gso_*
options which are only used on the tx path, and a previously unused 4
byte hole.
When skbs are coalesced either in the sk_receive_queue or the
out_of_order_queue always choose the timestamp of the appended skb to
maintain the invariant of returning the timestamp of the last byte in
the recvmsg buffer.
Signed-off-by: Mike Maloney <maloney@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Few cleanups including: bpf_redirect_map() is really XDP only due to
the return code. Move it to a more appropriate location where we do
the XDP redirect handling and change it's name into bpf_xdp_redirect_map()
to make it consistent to the bpf_xdp_redirect() helper.
xdp_do_redirect_map() helper can be static since only used out of filter.c
file. Drop the goto in xdp_do_generic_redirect() and only return errors
directly. In xdp_do_flush_map() only clear ri->map_to_flush which is the
arg we're using in that function, ri->map is cleared earlier along with
ri->ifindex.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
High order GFP_KERNEL allocations can stress the host badly.
Use modern kvmalloc_array()/kvfree() instead of custom
allocations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds ERSPAN type II tunnel support. The implementation
is based on the draft at [1]. One of the purposes is for Linux
box to be able to receive ERSPAN monitoring traffic sent from
the Cisco switch, by creating a ERSPAN tunnel device.
In addition, the patch also adds ERSPAN TX, so Linux virtual
switch can redirect monitored traffic to the ERSPAN tunnel device.
The traffic will be encapsulated into ERSPAN and sent out.
The implementation reuses tunnel key as ERSPAN session ID, and
field 'erspan' as ERSPAN Index fields:
./ip link add dev ers11 type erspan seq key 100 erspan 123 \
local 172.16.1.200 remote 172.16.1.100
To use the above device as ERSPAN receiver, configure
Nexus 5000 switch as below:
monitor session 100 type erspan-source
erspan-id 123
vrf default
destination ip 172.16.1.200
source interface Ethernet1/11 both
source interface Ethernet1/12 both
no shut
monitor erspan origin ip-address 172.16.1.100 global
[1] https://tools.ietf.org/html/draft-foschiano-erspan-01
[2] iproute2 patch: http://marc.info/?l=linux-netdev&m=150306086924951&w=2
[3] test script: http://marc.info/?l=linux-netdev&m=150231021807304&w=2
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: Meenakshi Vohra <mvohra@vmware.com>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove two references to ufo in the udp send path that are no longer
reachable now that ufo has been removed.
Commit 85f1bd9a7b ("udp: consistently apply ufo or fragmentation")
is a fix to ufo. It is safe to revert what remains of it.
Also, no skb can enter ip_append_page with skb_is_gso true now that
skb_shinfo(skb)->gso_type is no longer set in ip_append_page/_data.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_peer_is_proven needs a proper route to make the
determination, but dst always is NULL. This bug may
be there at the beginning of git tree. This does not
look serious enough to deserve backports to stable
versions.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the broadcast send link after 100 attempts has failed to
transfer a packet to all peers, we consider it stale, and reset
it. Thereafter it needs to re-synchronize with the peers, something
currently done by just resetting and re-establishing all links to
all peers. This has turned out to be overkill, with potentially
unwanted consequences for the remaining cluster.
A closer analysis reveals that this can be done much simpler. When
this kind of failure happens, for reasons that may lie outside the
TIPC protocol, it is typically only one peer which is failing to
receive and acknowledge packets. It is hence sufficient to identify
and reset the links only to that peer to resolve the situation, without
having to reset the broadcast link at all. This solution entails a much
lower risk of negative consequences for the own node as well as for
the overall cluster.
We implement this change in this commit.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3fcece12bc ("net: store port/representator id in metadata_dst")
added a new type field to metadata_dst, but metadata_dst_free() wasn't
updated to check it before freeing the METADATA_IP_TUNNEL specific dst
cache entry.
This is not currently causing problems since it's far enough back in the
struct to be zeroed for the only other type currently in existance
(METADATA_HW_PORT_MUX), but nevertheless it's not correct.
Fixes: 3fcece12bc ("net: store port/representator id in metadata_dst")
Signed-off-by: David Lamparter <equinox@diac24.net>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Sridhar Samudrala <sridhar.samudrala@intel.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
One nagging difference between ipv4 and ipv6 is host routes for ipv6
addresses are installed using the loopback device or VRF / L3 Master
device. e.g.,
2001:db8:1::/120 dev veth0 proto kernel metric 256 pref medium
local 2001:db8:1::1 dev lo table local proto kernel metric 0 pref medium
Using the loopback device is convenient -- necessary for local tx, but
has some nasty side effects, most notably setting the 'lo' device down
causes all host routes for all local IPv6 address to be removed from the
FIB and completely breaks IPv6 networking across all interfaces.
This patch puts FIB entries for IPv6 routes against the device. This
simplifies the routes in the FIB, for example by making dst->dev and
rt6i_idev->dev the same (a future patch can look at removing the device
reference taken for rt6i_idev for FIB entries).
When copies are made on FIB lookups, the cloned route has dst->dev
set to loopback (or the L3 master device). This is needed for the
local Tx of packets to local addresses.
With fib entries allocated against the real network device, the addrconf
code that reinserts host routes on admin up of 'lo' is no longer needed.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
compile tested only, but saw no warnings/errors with
allmodconfig build.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-08-21
1) Support RX checksum with IPsec crypto offload for esp4/esp6.
From Ilan Tayari.
2) Fixup IPv6 checksums when doing IPsec crypto offload.
From Yossi Kuperman.
3) Auto load the xfrom offload modules if a user installs
a SA that requests IPsec offload. From Ilan Tayari.
4) Clear RX offload informations in xfrm_input to not
confuse the TX path with stale offload informations.
From Ilan Tayari.
5) Allow IPsec GSO for local sockets if the crypto operation
will be offloaded.
6) Support setting of an output mark to the xfrm_state.
This mark can be used to to do the tunnel route lookup.
From Lorenzo Colitti.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In fib6_add(), it is possible that fib6_add_1() picks an intermediate
node and sets the node's fn->leaf to NULL in order to add this new
route. However, if fib6_add_rt2node() fails to add the new
route for some reason, fn->leaf will be left as NULL and could
potentially cause crash when fn->leaf is accessed in fib6_locate().
This patch makes sure fib6_repair_tree() is called to properly repair
fn->leaf in the above failure case.
Here is the syzkaller reported general protection fault in fib6_locate:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 0 PID: 40937 Comm: syz-executor3 Not tainted
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task: ffff8801d7d64100 ti: ffff8801d01a0000 task.ti: ffff8801d01a0000
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] __ipv6_prefix_equal64_half include/net/ipv6.h:475 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] ipv6_prefix_equal include/net/ipv6.h:492 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] fib6_locate_1 net/ipv6/ip6_fib.c:1210 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] fib6_locate+0x281/0x3c0 net/ipv6/ip6_fib.c:1233
RSP: 0018:ffff8801d01a36a8 EFLAGS: 00010202
RAX: 0000000000000020 RBX: ffff8801bc790e00 RCX: ffffc90002983000
RDX: 0000000000001219 RSI: ffff8801d01a37a0 RDI: 0000000000000100
RBP: ffff8801d01a36f0 R08: 00000000000000ff R09: 0000000000000000
R10: 0000000000000003 R11: 0000000000000000 R12: 0000000000000001
R13: dffffc0000000000 R14: ffff8801d01a37a0 R15: 0000000000000000
FS: 00007f6afd68c700(0000) GS:ffff8801db400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004c6340 CR3: 00000000ba41f000 CR4: 00000000001426f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
ffff8801d01a37a8 ffff8801d01a3780 ffffed003a0346f5 0000000c82a23ea0
ffff8800b7bd7700 ffff8801d01a3780 ffff8800b6a1c940 ffffffff82a23ea0
ffff8801d01a3920 ffff8801d01a3748 ffffffff82a223d6 ffff8801d7d64988
Call Trace:
[<ffffffff82a223d6>] ip6_route_del+0x106/0x570 net/ipv6/route.c:2109
[<ffffffff82a23f9d>] inet6_rtm_delroute+0xfd/0x100 net/ipv6/route.c:3075
[<ffffffff82621359>] rtnetlink_rcv_msg+0x549/0x7a0 net/core/rtnetlink.c:3450
[<ffffffff8274c1d1>] netlink_rcv_skb+0x141/0x370 net/netlink/af_netlink.c:2281
[<ffffffff82613ddf>] rtnetlink_rcv+0x2f/0x40 net/core/rtnetlink.c:3456
[<ffffffff8274ad38>] netlink_unicast_kernel net/netlink/af_netlink.c:1206 [inline]
[<ffffffff8274ad38>] netlink_unicast+0x518/0x750 net/netlink/af_netlink.c:1232
[<ffffffff8274b83e>] netlink_sendmsg+0x8ce/0xc30 net/netlink/af_netlink.c:1778
[<ffffffff82564aff>] sock_sendmsg_nosec net/socket.c:609 [inline]
[<ffffffff82564aff>] sock_sendmsg+0xcf/0x110 net/socket.c:619
[<ffffffff82564d62>] sock_write_iter+0x222/0x3a0 net/socket.c:834
[<ffffffff8178523d>] new_sync_write+0x1dd/0x2b0 fs/read_write.c:478
[<ffffffff817853f4>] __vfs_write+0xe4/0x110 fs/read_write.c:491
[<ffffffff81786c38>] vfs_write+0x178/0x4b0 fs/read_write.c:538
[<ffffffff817892a9>] SYSC_write fs/read_write.c:585 [inline]
[<ffffffff817892a9>] SyS_write+0xd9/0x1b0 fs/read_write.c:577
[<ffffffff82c71e32>] entry_SYSCALL_64_fastpath+0x12/0x17
Note: there is no "Fixes" tag as this seems to be a bug introduced
very early.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make code closer to current style. Mostly whitespace changes.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The XPS queue attributes can be ro_after_init.
Also use __ATTR_RX macros to simplify initialization.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The show and store functions don't need/use the attribute.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The attributes of net devices are immutable.
Ideally, attribute groups would contain const attributes
but there are too many places that do modifications of list
during startup (in other code) to allow that.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The net_class in sysfs is only modified on init.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions are wrapper arount class_create_file which can take a
const attribute.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If kobject_init_and_add failed, then the failure path would
decrement the reference count of the queue kobject whose reference
count was already zero.
Fixes: 114cf58021 ("bql: Byte queue limits")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we know in some target's checkentry it may dereference par.entryinfo
to check entry stuff inside. But when sched action calls xt_check_target,
par.entryinfo is set with NULL. It would cause kernel panic when calling
some targets.
It can be reproduce with:
# tc qd add dev eth1 ingress handle ffff:
# tc filter add dev eth1 parent ffff: u32 match u32 0 0 action xt \
-j ECN --ecn-tcp-remove
It could also crash kernel when using target CLUSTERIP or TPROXY.
By now there's no proper value for par.entryinfo in ipt_init_target,
but it can not be set with NULL. This patch is to void all these
panics by setting it with an ipt_entry obj with all members = 0.
Note that this issue has been there since the very beginning.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
