This allows setting the MAC address and specifying that the firmware
will be requested from userspace (because there might not be a hardware
EEPROM connected to the chip) for ath9k based PCI devices using
the device tree.
There is some out-of-tree code to "convert devicetree to
ath9k_platform_data" (for example in OpenWrt and LEDE) which becomes
obsolete with this patch.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This can be used when the ath_bus_type has to be presented in a log
message or firmware filename.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The active_high LED of my Wistron DNMA-92 is still being recognized as
active_low on 4.7.6 mainline. When I was preparing my former commit
0f9edcdd88 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92
cards.") to fix that I must have somehow messed up with testing, because
I tested the final version of that patch before sending it, and it was
apparently working; but now it is not working on 4.7.6 mainline.
I initially added the PCI_DEVICE_SUB section for 0x0029/0x2096 above the
PCI_VDEVICE section for 0x0029; but then I moved the former below the
latter after seeing how 0x002A sections were sorted in the file.
This turned out to be wrong: if a generic PCI_VDEVICE entry (that has
both subvendor and subdevice IDs set to PCI_ANY_ID) is put before a more
specific one (PCI_DEVICE_SUB), then the generic PCI_VDEVICE entry will
match first and will be used.
With this patch, 0x0029/0x2096 has finally got active_high LED on 4.7.6.
While I'm at it, let's fix 0x002A too by also moving its generic definition
below its specific ones.
Fixes: 0f9edcdd88 ("ath9k: Fix LED polarity for some Mini PCI AR9220 MB92 cards.")
Cc: <stable@vger.kernel.org> #4.7+
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
[kvalo@qca.qualcomm.com: improve the commit log based on email discussions]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath.git patches for 4.10. Major changes:
ath10k
* allow setting coverage class for first generation cards
* read regulatory domain from ACPI
ath9k
* disable RNG by default
* Use dev_coredumpmsg() to prevent locking the driver;
* Small fix to pass the AID to the FW;
* Use FW PS decisions with multi-queue;
-----BEGIN PGP SIGNATURE-----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=D+eo
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-10-25-2' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Finalize and enable dynamic queue allocation;
* Use dev_coredumpmsg() to prevent locking the driver;
* Small fix to pass the AID to the FW;
* Use FW PS decisions with multi-queue;
iwlmvm currently uses dev_coredumpm() to collect multiple
buffers, but this has the downside of pinning the module
until the coredump expires, if the data isn't read by any
userspace.
Avoid this by using the new dev_coredumpsg() method. We
still copy the data from the old way of generating it, but
neither hold on to vmalloc'ed data for a long time, nor do
we pin the module now.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New firmwares support dynamic queue allocation (DQA), which enables
on-demand allocation of queues per RA/TID, instead of allocating them
statically per vif. This allows an AP to send, for instance, BE
traffic to STA2 even if it also needs to send traffic to a sleeping
STA1, without being blocked by the sleeping station.
The implementation in the driver is now ready, so we can enable this
feature by default when running firmwares that support it.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
[reworded the commit message]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
- set max_mtu in wil6210 driver
- set max_mtu in atmel driver
- set min/max_mtu in cisco airo driver, remove airo_change_mtu
- set min/max_mtu in ipw2100/ipw2200 drivers, remove libipw_change_mtu
- set min/max_mtu in p80211netdev, remove wlan_change_mtu
- set min/max_mtu in net/mac80211/iface.c and remove ieee80211_change_mtu
- set min/max_mtu in wimax/i2400m and remove i2400m_change_mtu
- set min/max_mtu in intersil/hostap and remove prism2_change_mtu
- set min/max_mtu in intersil/orinoco
- set min/max_mtu in tty/n_gsm and remove gsm_change_mtu
CC: netdev@vger.kernel.org
CC: linux-wireless@vger.kernel.org
CC: Maya Erez <qca_merez@qca.qualcomm.com>
CC: Simon Kelley <simon@thekelleys.org.uk>
CC: Stanislav Yakovlev <stas.yakovlev@gmail.com>
CC: Johannes Berg <johannes@sipsolutions.net>
CC: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when configuring the cab queue the scheduler is configured
without station id - which results in station id 0.
In DQA mode this causes firmware to assert later on when the actual
station 0 is added with an empty tfd_queue_mask.
Fix that by configuring the queue to the broadcast station.
This is a bit trickier since the queue should not be included in the
tfd_queue_mask of the ADD_STA since it is a multicast queue, and the
tfd_queue_mask is only unicast queue. As a result the queue should be
enabled only after the broadcast station is added.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a peer associates, the firmware will soon want to know
its AID to be able to compute the TIM IE by itself.
In DQA, the firmware has all the information it needs to
update the TIM internally. The only missing part is the
AID.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of passing DRV_NAME pass a string that
represents the reason for the interrupt.
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When using RSS on 9000 series devices, we can't rely on processing the
received frames for station powersave handling, since they could be
processed on different CPUs and out of order.
In order to still manage the powersave of stations, the firmware sends
a notification on sleep->wake, wake->sleep and - for U-APSD - frames
received with PM while already sleeping (with the TID.)
With this, the driver can set AP_LINK_PS, which is required for real
parallel RX. In addition, this requires checking for PS-Poll frames
and calling ieee80211_sta_pspoll() appropriately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a STA has deferred traffic to TX, an appropriate bit
is turned on in %deferred_tx_frames to indicate deferred
traffic. This marking is never turned off, resulting in
iterating over TIDs with no deferred traffic.
Although this didn't cause any failures/errors/bugs, there
is still no point of iterating over these TIDs when not
needed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the TXQs are allocated on demand, so make
sure the sniffer STA tfd_queue_msk isn't set.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If a TXQ's marking as a reserved queue is removed,
when removing the STA the driver might try to access
out of bounds memory. Make sure the reserved queue
is freed only if it is still reserved.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a TXQ's owner is changed, the FW is indeed notified, but
the driver doesn't update the current metadata to reflect the
owner change. Fix that.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The quality of ADC entropy is 10 bits of min-entropy for
a 32-bit value, change '(((x) * 8 * 320) >> 10)' to
'(((x) * 8 * 10) >> 5)' for easier understanding.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
arvifs list is traversed within data_lock spin_lock in tasklet
context to fill channel information from the corresponding vif.
This means any access to arvifs list for add/del operations
should also be protected with the same spin_lock to avoid the
race. Fix this by performing list add/del on arvfis within the
data_lock. This could fix kernel panic something like the below.
LR is at ath10k_htt_rx_pktlog_completion_handler+0x100/0xb6c [ath10k_core]
PC is at ath10k_htt_rx_pktlog_completion_handler+0x1c0/0xb6c [ath10k_core]
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
[<bf4857f4>] (ath10k_htt_rx_pktlog_completion_handler+0x2f4/0xb6c [ath10k_core])
[<bf487540>] (ath10k_htt_txrx_compl_task+0x8b4/0x1188 [ath10k_core])
[<c00312d4>] (tasklet_action+0x8c/0xec)
[<c00309a8>] (__do_softirq+0xdc/0x208)
[<c0030d6c>] (irq_exit+0x84/0xe0)
[<c005db04>] (__handle_domain_irq+0x80/0xa0)
[<c00085c4>] (gic_handle_irq+0x38/0x5c)
[<c0009640>] (__irq_svc+0x40/0x74)
(gdb) list *(ath10k_htt_rx_pktlog_completion_handler+0x1c0)
0x136c0 is in ath10k_htt_rx_h_channel (drivers/net/wireless/ath/ath10k/htt_rx.c:769)
764 struct cfg80211_chan_def def;
765
766 lockdep_assert_held(&ar->data_lock);
767
768 list_for_each_entry(arvif, &ar->arvifs, list) {
769 if (arvif->vdev_id == vdev_id &&
770 ath10k_mac_vif_chan(arvif->vif, &def) == 0)
771 return def.chan;
772 }
773
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
'ath10k_htt_rx_h_unchain' needs to be called only if the return
value from 'ath10k_htt_rx_amsdu_pop' is 1('chained msdu's'), this
change makes it more explicit and avoids doing a skb_peek, fetching
rx descriptor pointer, checking rx msdu decap format for the case of
ret = 0 (unchained msdus). Found this change during code walk through,
not sure if this addresses any issue.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull misc vfs updates from Al Viro:
"Assorted misc bits and pieces.
There are several single-topic branches left after this (rename2
series from Miklos, current_time series from Deepa Dinamani, xattr
series from Andreas, uaccess stuff from from me) and I'd prefer to
send those separately"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (39 commits)
proc: switch auxv to use of __mem_open()
hpfs: support FIEMAP
cifs: get rid of unused arguments of CIFSSMBWrite()
posix_acl: uapi header split
posix_acl: xattr representation cleanups
fs/aio.c: eliminate redundant loads in put_aio_ring_file
fs/internal.h: add const to ns_dentry_operations declaration
compat: remove compat_printk()
fs/buffer.c: make __getblk_slow() static
proc: unsigned file descriptors
fs/file: more unsigned file descriptors
fs: compat: remove redundant check of nr_segs
cachefiles: Fix attempt to read i_blocks after deleting file [ver #2]
cifs: don't use memcpy() to copy struct iov_iter
get rid of separate multipage fault-in primitives
fs: Avoid premature clearing of capabilities
fs: Give dentry to inode_change_ok() instead of inode
fuse: Propagate dentry down to inode_change_ok()
ceph: Propagate dentry down to inode_change_ok()
xfs: Propagate dentry down to inode_change_ok()
...
When power is removed from the device, all of the SDIO settings
return to default. Fix that by reconfiguring after power is
applied.
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This allows the hardware to be restarted, as it will cause the
sg to be reinitialized.
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To reuse the busreqs in case of hardware restart, they must be
properly reinitialized. If the scat_req pointer isn't reset to
0, __ath6kl_sdio_write_async() will assume there is sg work to be
done (causing a kernel OOPS).
Signed-off-by: James Minor <james.minor@ni.com>
Reviewed-by: Steve deRosier <steve.derosier@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking updates from David Miller:
1) BBR TCP congestion control, from Neal Cardwell, Yuchung Cheng and
co. at Google. https://lwn.net/Articles/701165/
2) Do TCP Small Queues for retransmits, from Eric Dumazet.
3) Support collect_md mode for all IPV4 and IPV6 tunnels, from Alexei
Starovoitov.
4) Allow cls_flower to classify packets in ip tunnels, from Amir Vadai.
5) Support DSA tagging in older mv88e6xxx switches, from Andrew Lunn.
6) Support GMAC protocol in iwlwifi mwm, from Ayala Beker.
7) Support ndo_poll_controller in mlx5, from Calvin Owens.
8) Move VRF processing to an output hook and allow l3mdev to be
loopback, from David Ahern.
9) Support SOCK_DESTROY for UDP sockets. Also from David Ahern.
10) Congestion control in RXRPC, from David Howells.
11) Support geneve RX offload in ixgbe, from Emil Tantilov.
12) When hitting pressure for new incoming TCP data SKBs, perform a
partial rathern than a full purge of the OFO queue (which could be
huge). From Eric Dumazet.
13) Convert XFRM state and policy lookups to RCU, from Florian Westphal.
14) Support RX network flow classification to igb, from Gangfeng Huang.
15) Hardware offloading of eBPF in nfp driver, from Jakub Kicinski.
16) New skbmod packet action, from Jamal Hadi Salim.
17) Remove some inefficiencies in snmp proc output, from Jia He.
18) Add FIB notifications to properly propagate route changes to
hardware which is doing forwarding offloading. From Jiri Pirko.
19) New dsa driver for qca8xxx chips, from John Crispin.
20) Implement RFC7559 ipv6 router solicitation backoff, from Maciej
Żenczykowski.
21) Add L3 mode to ipvlan, from Mahesh Bandewar.
22) Support 802.1ad in mlx4, from Moshe Shemesh.
23) Support hardware LRO in mediatek driver, from Nelson Chang.
24) Add TC offloading to mlx5, from Or Gerlitz.
25) Convert various drivers to ethtool ksettings interfaces, from
Philippe Reynes.
26) TX max rate limiting for cxgb4, from Rahul Lakkireddy.
27) NAPI support for ath10k, from Rajkumar Manoharan.
28) Support XDP in mlx5, from Rana Shahout and Saeed Mahameed.
29) UDP replicast support in TIPC, from Richard Alpe.
30) Per-queue statistics for qed driver, from Sudarsana Reddy Kalluru.
31) Support BQL in thunderx driver, from Sunil Goutham.
32) TSO support in alx driver, from Tobias Regnery.
33) Add stream parser engine and use it in kcm.
34) Support async DHCP replies in ipconfig module, from Uwe
Kleine-König.
35) DSA port fast aging for mv88e6xxx driver, from Vivien Didelot.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1715 commits)
mlxsw: switchx2: Fix misuse of hard_header_len
mlxsw: spectrum: Fix misuse of hard_header_len
net/faraday: Stop NCSI device on shutdown
net/ncsi: Introduce ncsi_stop_dev()
net/ncsi: Rework the channel monitoring
net/ncsi: Allow to extend NCSI request properties
net/ncsi: Rework request index allocation
net/ncsi: Don't probe on the reserved channel ID (0x1f)
net/ncsi: Introduce NCSI_RESERVED_CHANNEL
net/ncsi: Avoid unused-value build warning from ia64-linux-gcc
net: Add netdev all_adj_list refcnt propagation to fix panic
net: phy: Add Edge-rate driver for Microsemi PHYs.
vmxnet3: Wake queue from reset work
i40e: avoid NULL pointer dereference and recursive errors on early PCI error
qed: Add RoCE ll2 & GSI support
qed: Add support for memory registeration verbs
qed: Add support for QP verbs
qed: PD,PKEY and CQ verb support
qed: Add support for RoCE hw init
qede: Add qedr framework
...
Unfortunately ath10k does not generally allow modifying the coverage class
with the stock firmware and Qualcomm has so far refused to implement this
feature so that it can be properly supported in ath10k. If we however know
the registers that need to be modified for proper operation with a higher
coverage class, then we can do these modifications from the driver.
This is a hack and might cause subtle problems but as it's not enabled by
default (only when user space changes the coverage class explicitly) it should
not cause new problems for existing setups. But still this should be considered
as an experimental feature and used with caution.
This patch implements the support for first generation cards (QCA9880, QCA9887
and so on) which are based on a core that is similar to ath9k. The registers
are modified in place and need to be re-written every time the firmware sets
them. To achieve this the register status is verified after certain WMI events
from the firmware.
The coverage class may not be modified temporarily right after the card
re-initializes the registers. This is for example the case during scanning.
Thanks to Sebastian Gottschall <s.gottschall@dd-wrt.com> for initially
working on a userspace support for this. This patch wouldn't have been
possible without this documentation.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This overrides whatever regulatory the device
EEPROM contains and uses what the platform says
instead - in this implementation the ACPI driver.
In case the hint is not programmed or corrupted (0xffff)
the device falls back to the eeprom programmed settings.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
[kvalo@qca.qualcomm.com: remove ifdef, change error handling, change info messages to dbg]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will be helpful for drivers that can acquire
alpha2 regulatory codes.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During offchannel scan, iw survey dump shows wrong values.
Fix this by assigning cycle counter wranarround type for
QCA9888 and QCA9884, they share same config with QCA4019.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch helps to get the TPC stats for 10.4 fw variants.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Here are the "big" driver core patches for 4.9-rc1. Also in here are a
number of debugfs fixes that cropped up due to the changes that happened
in 4.8 for that filesystem. Overall, nothing major, just a few fixes
and cleanups.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNw4PHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspLVYAoNXr
FXBHGb2tNT/1PLfvUCwd5PqWAJ9Khb5WAHtvjTmEN1zabz45aSbcrA==
=Uz6V
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are the "big" driver core patches for 4.9-rc1. Also in here are a
number of debugfs fixes that cropped up due to the changes that
happened in 4.8 for that filesystem. Overall, nothing major, just a
few fixes and cleanups.
All of these have been in linux-next with no reported issues"
* tag 'driver-core-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
drivers: dma-coherent: Move spinlock in dma_alloc_from_coherent()
drivers: dma-coherent: Fix DMA coherent size for less than page
MAINTAINERS: extend firmware_class maintainer list
debugfs: propagate release() call result
driver-core: platform: Catch errors from calls to irq_get_irq_data
sysfs print name of undiscoverable attribute group
carl9170: fix debugfs crashes
b43legacy: fix debugfs crash
b43: fix debugfs crash
debugfs: introduce a public file_operations accessor
device core: Remove deprecated create_singlethread_workqueue
drivers/base dmam_declare_coherent_memory leaks
platform: don't return 0 from platform_get_irq[_byname]() on error
cpu: clean up register_cpu func
dma-mapping: use vma_pages().
drivers: dma-coherent: use vma_pages().
attribute_container: Fix typo
base: soc: make it explicitly non-modular
drivers: base: dma-mapping: page align the size when unmap_kernel_range
platform driver: fix use-after-free in platform_device_del()
...
Major changes:
iwlwifi
* work for new hardware support continues
* dynamic queue allocation stabilization
* improvements in the MSIx code
* multiqueue support work continues
* new firmware version support (API 26)
* add 8275 series support
* add 9560 series support
* add support for MU-MIMO sniffer
* add support for RRM by scan
* add support for "reverse" rx packet injection faking hw descriptors
* migrate to devm memory allocation handling
* Remove support for older firmwares (API older than -17 and -22)
wl12xx
* support booting the same rootfs with both wl12xx and wl18xx
hostap
* mark the driver as obsolete
ath9k
* disable RNG by default
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJX7UPbAAoJEG4XJFUm622bmgIH/2fCGwkejWpN/KLckRU0I+ze
Yx0o8aEmYAOnZW4tVVGAtEAxeLdzjMeHKsyJ+4RBguhRpbV2FTKnzg7LYeqqI3Vw
LjZwKLrrBj4DXQwtTxBC8uScUpDU91U4mZwOTN+UkyXQb9hDxl2CH3MUgc432hcd
flSXTnaY8TJzFuHM9Q/TORXmSx3VtMqYnqUYcyoaKEC8ZiSr6dWtzh5OkPS+O4Di
4CNPDjEK5uhe46gDWJhGY2bx6TnzGx6O5mRfWfzdvL3Fzy9a3rGabA9Iis+9b23n
m/5OKwN97jcPZiWrP+c2qfVmFjv2upCUUAuLuT0k05/DK70qpGKyMwklsNcC44Q=
=lRW5
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-09-29' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
wireless-drivers-next patches for 4.9
Major changes:
iwlwifi
* work for new hardware support continues
* dynamic queue allocation stabilization
* improvements in the MSIx code
* multiqueue support work continues
* new firmware version support (API 26)
* add 8275 series support
* add 9560 series support
* add support for MU-MIMO sniffer
* add support for RRM by scan
* add support for "reverse" rx packet injection faking hw descriptors
* migrate to devm memory allocation handling
* Remove support for older firmwares (API older than -17 and -22)
wl12xx
* support booting the same rootfs with both wl12xx and wl18xx
hostap
* mark the driver as obsolete
ath9k
* disable RNG by default
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with W=1, we got one warning as belows:
drivers/net/wireless/ath/ath6kl/wmi.c:3509:6: warning: variable ‘ret’
set but not used [-Wunused-but-set-variable]
At the end of ath6kl_wmi_set_pvb_cmd, it is returned by 0 regardless of
return value of ath6kl_wmi_cmd_send.
This patch fixes return value from 0 to ret that has result of
ath6kl_wmi_cmd_send execution.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath9k RNG will dominates all the noise sources from the real HW
RNG, disable it by default. But we strongly recommand to enable
it if the system without HW RNG, especially on embedded systems.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Acked-by: Stephan Mueller <smueller@chronox.de>
Acked-by: Stephan Mueller <smueller@chronox.de>
Reviewed-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Firmware is running watchdog timer for tracking copy engine ring index
and write index. Whenever both indices are stuck at same location for
given duration, watchdog will be trigger to assert target. While
updating copy engine destination ring write index, driver ensures that
write index will not be same as read index by finding delta between these
two indices (CE_RING_DELTA).
HTT target to host copy engine (CE5) is special case where ring buffers
will be reused and delta check is not applied while updating write index.
In rare scenario, whenever CE5 ring is full, both indices will be referring
same location and this is causing CE ring stuck issue as explained
above. This issue is originally reported on IPQ4019 during long hour stress
testing and during veriwave max clients testsuites. The same issue is
also observed in other chips as well. Fix this by ensuring that write
index is one less than read index which means that full ring is
available for receiving data.
Cc: stable@vger.kernel.org
Tested-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ignore processing further in SWBA event scheduled for a vif, if mac80211
has marked the particular vif for stop beaconing and brought the vdev
down in 'ath10k_control_beaconing'. This should potentially avoid ath10k
warning/error messages while running continuous wifi down/up with max
number of vaps configured. Found this change during code walk through
and going through other beacon configuration related functions in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix to return a negative error code from the error handling case
instead of 0, as done elsewhere in function ath10k_ahb_probe() or
ath10k_ahb_resource_init().
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Flowrings contain skbs waiting for transmission that were passed to us
by netif. It means we checked every one of them looking for 802.1x
Ethernet type. When deleting flowring we have to use freeing function
that will check for 802.1x type as well.
Freeing skbs without a proper check was leading to counter not being
properly decreased. This was triggering a WARNING every time
brcmf_netdev_wait_pend8021x was called.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend@broadcom.com>
Cc: stable@vger.kernel.org # 4.5+
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Even with timeout increased to 950 ms we get WARNINGs from time to time.
It mostly happens on A-MPDU stalls (e.g. when station goes out of
range). It may take up to 5-10 secods for the firmware to recover and
for that time it doesn't process packets.
It's still useful to have a message on time out as it may indicate some
firmware problem and incorrect key update. Raising a WARNING however
wasn't really that necessary, it doesn't point to any driver bug anymore
and backtrace wasn't much useful.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The entries in this enum may be referenced in debug output. Adding explicit
values simplifies the lookup.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Only rtl8821ae implements WOWLAN; however, the other drivers may receive
a call requesting information about this mode. The other drivers need to
ignore the request rather than logging that the default branch of the
switch statement has been reached.
Reported by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Help along debugging by showing what switch/case variable is not
being processed in these messages.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Small fix in CTDP error handling;
* Remove support for older firmwares;
* Clean-ups and a few simple fixes here and there.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MdMZ
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-09-26' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Some new HW IDs;
* Small fix in CTDP error handling;
* Remove support for older firmwares;
* Clean-ups and a few simple fixes here and there.
The (1 << x) - 1 trick won't work when you
are trying to fill up all 64 bits, so add special
case for that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: remove the sentence about moving limits]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
They are not necessarily named in an intuitive manner,
so at least add some comments to help the next person.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipset from QCA99X0 onwards (QCA99X0, QCA9984, QCA4019 & future)
rx_hdr_status is not padded to align in 4-byte boundary. Define a
new hw_params field to handle different alignment behaviour between
different hw. This patch fixes improper retrieval of rfc1042 header
with QCA4019. This patch along with "ath10k: Properly remove padding
from the start of rx payload" will fix traffic failure in ethernet
decap mode for QCA4019.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Since reset_control_get() never returns NULL, we can use IS_ERR()
instead of IS_ERR_OR_NULL(). The return statements can be simpler
as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
