refactor module parameter debug_fw to act as "fw debug mode",
where driver do nothing but allow card memory access.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
"echo" used to be called when no firmware loaded to the NIC,
this causes error output.
Probe firmware with "echo" only after it returned "ready" event.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hardware older than Sparrow B0 obsolete.
There is no WiFi product that uses this hardware.
Recent firmware does not support it either.
Remove driver support.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce boot loader. Instead of the operational firmware,
very small boot loader is burned to the on-board flash. Boot loader
initializes hardware upon reset, and prepares for low power mode.
Boot loader reports MAC address and detects radio chip connected.
Driver loads firmware only when bringing up interface. All information
required to set up network interface, most important is MAC address,
reported by the boot loader
The firmware composed of 2 files:
- wil6210.fw - firmware itself (compiled code + data)
- wil6210.board - board file (various board and radio dependent
calibrations and parameters)
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add advanced interrupt moderation support available since "Sparrow B0".
Legacy interrupt moderation used only one counter to moderate tx, rx,
and misc interrupts.
Advanced interrupt moderation bypasses misc, and handles separately tx
and rx interrupts. In addition it has two timers for each interrupt type.
Max burst duration timer which defines how long to postpone interrupt after
first event (receive event for rx and tx complete event for tx), and
interframe timeout which defines how to determine the end of the burst and
issue interrupt even if the first timer still pending.
Capabilities flags in wil_priv is set on initialization according to
HW. The rest of the code checks for advanced interrupt capability bit
in capabilities flags field.
Debugfs is split accordingly: "legacy" interrupt moderation remains
unchanged, new debugs files added for advanced interrupt moderation
support.
Module params are aligned to support advanced interrupt moderation
(tx & rx). When not available (for legacy interrupt moderation) will
use only rx configuration; Tx configuration will be ignored in this
case.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use the proper reset follow based on HW capabilities
detection instead of chip ID.
Remove old hw ID mechanism which was used only for reset flow.
Remove support for Marlon A0.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Read relevant information (HW ID for now) once on init
and set capabilities accordingly.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When interface stopped while running intensive Rx traffic, the following oops
observed:
[89846.734683] Call trace:
[89846.737117] [<ffffffc00083aa64>] dev_gro_receive+0xac/0x358
[89846.742674] [<ffffffc00083ae94>] napi_gro_receive+0x24/0xa4
[89846.748251] [<ffffffbffc1c2f88>] $x+0xec/0x1f8 [wil6210] wil_netif_rx_any
[89846.753547] [<ffffffbffc1c4830>] $x+0x34/0x54 [wil6210] wil_release_reorder_frame
[89846.758755] [<ffffffbffc1c48ac>] wil_release_reorder_frames+0x5c/0x78 [wil6210]
[89846.766044] [<ffffffbffc1c4bf8>] wil_tid_ampdu_rx_free+0x20/0x48 [wil6210]
[89846.772901] [<ffffffbffc1bedc8>] $x+0x190/0x1e8 [wil6210]
[89846.778285] [<ffffffbffc1c0ed4>] wmi_event_worker+0x230/0x2f8 [wil6210]
[89846.784865] [<ffffffc0000b0bc8>] process_one_work+0x278/0x3fc
[89846.790591] [<ffffffc0000b1218>] worker_thread+0x200/0x330
[89846.796060] [<ffffffc0000b6664>] kthread+0xac/0xb8
[89846.800836] Code: b940c661 f9406a62 8b010041 f9400026 (f8636882)
[89846.807008] ---[ end trace d6fdc17cd27d18f6 ]---
Reason is the following: when removing Rx vring
(wil_netdev_ops.ndo_stop -> wil_stop -> wil_down -> __wil_down -> wil_rx_fini),
Rx interrupt occurs. It trigger Rx NAPI, calling wil_rx_handle() that reaps
(already cleaned) buffer, causing skb referring to garbage memory being set into reorder buffer.
Then, network stack trying to access this buffer and fails.
Prevent Rx NAPI from being scheduled if device going to stop. Bit wil_status_napi_en reflects
NAPI enablement state, check it when triggering Rx NAPI.
Testing shows that check for wil_status_napi_en sometimes gets negative, and new error message
get printed - in this case kernel oops would be observed. Original oops is no more reproducible.
This change requires also changes in the AP flows.
Properly enable/disable NAPI for the AP. Make sure Rx VRING is disabled
when resetting target.
For this, promote __wil_up() and __wil_down() to the module scope, and use it
in the relevant flows.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver disabled PCI master before making sure HW is idle.
This caused memory corruption in case HW access system memory after
PCI master got disabled.
The fix is to change uninit sequence. Make sure FW/HW is idle before
disabling PCI
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
added misc printouts in some init/uninit functions for better traceability
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New module (wil_platform) for handling platform specific tasks
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'wil' released in wil_if_free(); save iomapped address aside to
properly unmap it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If firmware broken on the boot time, Sparrow card enumerates as
device 0x302 instead of 0x310. Allow using this ID
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix Copyright headers in all files changed in 2014, to mention 2014
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New hardware release appears; it require some changes to properly support it.
Introduce struct wil_board and "board" attribute in wil6210_priv;
keep hardware variant information in this structure.
fill it on probe(). Used in the reset flow.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are platforms where INTx can't be routed by ACPI,
this leads to pci_enable_device failure. Re-try pretending we have
MSI already configured; in this case pci_enable_device do not try
to configure INTx. However, MSI could still work.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the pcie_bus.c, knowledge about debugfs is not necessary
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usable for debugging, to be able to obtain FW traces
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use proper format %pad for the dma_addr_t arguments;
prefix %p with 0x, as %p don't print is by itself
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reshuffle prints to consolidate firmware/hardware information
report upon card init
Convert print for unhandled MISC ISR bits to "debug" - it is
normal situation and not an "error"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When disconnecting some CID, corresponded Tx vring get released. During vring
release, all descriptors get freed. It is possible that Tx NAPI working on the same
vring simultaneously. If it happens, descriptor may be double freed.
To protect from the race above, make sure NAPI won't process the same vring.
Introduce 'enabled' flag in the struct vring_tx_data. Proceed with Tx NAPI only if
'enabled' flag set. Prior to Tx vring release, clear this flag and make sure NAPI
get synchronized.
NAPI enablement status protected by wil->mutex, add protection where it was
missing and check for it.
During reset, disconnect all peers first, then proceed with the Rx vring. It allows for
the disconnect flow to observe proper 'wil->status' and correctly notify cfg80211 about
connection status change
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware bug triggered by the MSI init while INTx asserted for some reason.
De-assert INTx prior to MSI set-up
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for new chip revision. Revision read from the
internal register, PCIE config's "revision id" register
do not indicate HW version properly
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: wil6210@qca.qualcomm.com
Cc: netdev@vger.kernel.org
Cc: linux-pci@vger.kernel.org
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce debug category "MISC", convert all raw wil_dbg() to this category.
This improves dynamic debug manageability
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for the 60 GHz 802.11ad Wilocity card
through a new driver, wil6210. Wilocity implemented the
firmware, QCA maintains the device driver.
Currently supported:
- STA: with security
- AP: limited to 1 connected STA, security disabled
- Monitor: due to a hardware/firmware limitation
either control or non-control frames are monitored
Using a STA and AP with this drive, one can assemble
a fully functional BSS. Throughput of 1.2Gbps is achieved
with iperf.
The wil6210 cards have on-board flash memory for the
firmware, the cards comes pre-flashed and no firmware
download is required.
For more details see:
http://wireless.kernel.org/en/users/Drivers/wil6210
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
