RDS ping messages are sent with a non-zero src port to a zero
dst port, so that the rds pong messages can be sent back to the
originators src port. However if a confused/malicious sender
sends a ping with a 0 src port, we'd have an infinite ping-pong
loop. To avoid this, the receiver should ignore ping messages
with a 0 src port.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When reconnecting, the peer with the smaller IP address will initiate
the reconnect, to avoid needless duelling SYN issues.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds ->conn_path_connect callbacks in the rds_transport
that are used to set up a single connection path.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->sk_user_data contains a pointer to the rds_conn_path
for the socket. Use this consistently in the rds_tcp_data_ready
callbacks to get the rds_conn_path for rds_recv_incoming.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The socket callbacks should all operate on a struct rds_conn_path,
in preparation for a MP capable RDS-TCP.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A single rds_connection may have multiple rds_conn_paths that have
to be carefully and correctly destroyed, for both rmmod and
netns-delete cases.
For both cases, we extract a single rds_tcp_connection for
each conn into a temporary list, and then invoke rds_conn_destroy()
which iteratively dismantles every path in the rds_connection.
For the netns deletion case, we additionally have to make sure
that we do not leave a socket in TIME_WAIT state, as this will
hold up the netns deletion. Thus we call rds_tcp_conn_paths_destroy()
to reset state quickly.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct rds_tcp_connection is the transport-specific private
data structure that tracks TCP information per rds_conn_path.
Modify this structure to have a back-pointer to the rds_conn_path
for which it is the ->cp_transport_data.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The c_passive bit is only intended for the IB transport and will
never be encountered in rds-tcp, so remove the dead logic that
predicates on this bit.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor code to avoid separate indirections for single-path
and multipath transports. All transports (both single and mp-capable)
will get a pointer to the rds_conn_path, and can trivially derive
the rds_connection from the ->cp_conn.
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds a bpf helper, bpf_skb_in_cgroup, to decide if a skb->sk
belongs to a descendant of a cgroup2. It is similar to the
feature added in netfilter:
commit c38c4597e4 ("netfilter: implement xt_cgroup cgroup2 path match")
The user is expected to populate a BPF_MAP_TYPE_CGROUP_ARRAY
which will be used by the bpf_skb_in_cgroup.
Modifications to the bpf verifier is to ensure BPF_MAP_TYPE_CGROUP_ARRAY
and bpf_skb_in_cgroup() are always used together.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Tejun Heo <tj@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since bpf_prog_get() and program type check is used in a couple of places,
refactor this into a small helper function that we can make use of. Since
the non RO prog->aux part is not used in performance critical paths and a
program destruction via RCU is rather very unlikley when doing the put, we
shouldn't have an issue just doing the bpf_prog_get() + prog->type != type
check, but actually not taking the ref at all (due to being in fdget() /
fdput() section of the bpf fd) is even cleaner and makes the diff smaller
as well, so just go for that. Callsites are changed to make use of the new
helper where possible.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new event - NETDEV_CHANGE_TX_QUEUE_LEN, this
will be triggered when tx_queue_len. It could be used by net device
who want to do some processing at that time. An example is tun who may
want to resize tx array when tx_queue_len is changed.
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cl->cl_vt alone is relative only to the current backlog period, while
the curve operates on cumulative virtual time. This patch adds missing
cl->cl_vtoff.
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a class is going passive, it should update its cl_vt first
to be consistent with the last dequeue operation.
Otherwise its cl_vt will be one packet behind and parent's cvtmax might
not be updated as well.
One possible side effect is if some class goes passive and subsequently
goes active /without/ its parent going passive - with cl_vt lagging one
packet behind - comparison made in init_vf() will be affected (same
period).
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is update to:
commit a09ceb0e08 ("sched: remove qdisc->drop")
That commit removed qdisc->drop, but left alone dlist and droplist
that no longer serve any meaningful purpose.
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
The condition can only succeed on wrong configurations.
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtime scheduling implemented in HFSC uses head of the queue to make
the decision about which packet to schedule next. But in case of any
head drop, the deadline calculated for the previous head is not
necessarily correct for the next head (unless both packets have the same
length).
Thanks to peek() function used during dequeue - which internally is a
dequeue operation - hfsc is almost safe from this issue, as peek()
dequeues and isolates the head storing it temporarily until the real
dequeue happens.
But there is one exception: if after the class activation a drop happens
before the first dequeue operation, there's never a chance to do the
peek().
Adding peek() call in enqueue - if this is the first packet in a new
backlog period AND the scheduler has realtime curve defined - fixes that
one corner case. The 1st hfsc_dequeue() will use that peeked packet,
similarly as every subsequent hfsc_dequeue() call uses packet peeked by
the previous call.
Signed-off-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some arches have virtually mapped kernel stacks, or will soon have.
tcp_md5_hash_header() uses an automatic variable to copy tcp header
before mangling th->check and calling crypto function, which might
be problematic on such arches.
David says that using percpu storage is also problematic on non SMP
builds.
Just use kmalloc() to allocate scratch areas.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding rule with NLM_F_EXCL flag then check if the same rule exist.
If yes then exit with -EEXIST.
This is already implemented in iproute2:
if (cmd == RTM_NEWRULE) {
req.n.nlmsg_flags |= NLM_F_CREATE|NLM_F_EXCL;
req.r.rtm_type = RTN_UNICAST;
}
Tested ipv4 and ipv6 with net-next linux on qemu x86
expected behavior after patch:
localhost ~ # ip rule
0: from all lookup local
32766: from all lookup main
32767: from all lookup default
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
localhost ~ # ip rule add from 10.46.177.97 lookup 104 pref 1005
RTNETLINK answers: File exists
localhost ~ # ip rule
0: from all lookup local
1005: from 10.46.177.97 lookup 104
32766: from all lookup main
32767: from all lookup default
There was already topic regarding this but I don't see any changes
merged and problem still occurs.
https://lkml.kernel.org/r/1135778809.5944.7.camel+%28%29+localhost+%21+localdomain
Signed-off-by: Mateusz Bajorski <mateusz.bajorski@nokia.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found that sometimes a restored tcp socket doesn't work.
A reason of this bug is incorrect window parameters and in this case
tcp_acceptable_seq() returns tcp_wnd_end(tp) instead of tp->snd_nxt. The
other side drops packets with this seq, because seq is less than
tp->rcv_nxt ( tcp_sequence() ).
Data from a send queue is sent only if there is enough space in a
window, so when we restore unacked data, we need to expand a window to
fit this data.
This was in a first version of this patch:
"tcp: extend window to fit all restored unacked data in a send queue"
Then Alexey recommended me to restore window parameters instead of
adjusted them according with data in a sent queue. This sounds resonable.
rcv_wnd has to be restored, because it was reported to another side
and the offered window is never shrunk.
One of reasons why we need to restore snd_wnd was described above.
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds stats support for the currently used IGMP/MLD types by the
bridge. The stats are per-port (plus one stat per-bridge) and per-direction
(RX/TX). The stats are exported via netlink via the new linkxstats API
(RTM_GETSTATS). In order to minimize the performance impact, a new option
is used to enable/disable the stats - multicast_stats_enabled, similar to
the recent vlan stats. Also in order to avoid multiple IGMP/MLD type
lookups and checks, we make use of the current "igmp" member of the bridge
private skb->cb region to record the type on Rx (both host-generated and
external packets pass by multicast_rcv()). We can do that since the igmp
member was used as a boolean and all the valid IGMP/MLD types are positive
values. The normal bridge fast-path is not affected at all, the only
affected paths are the flooding ones and since we make use of the IGMP/MLD
type, we can quickly determine if the packet should be counted using
cache-hot data (cb's igmp member). We add counters for:
* IGMP Queries
* IGMP Leaves
* IGMP v1/v2/v3 reports
* MLD Queries
* MLD Leaves
* MLD v1/v2 reports
These are invaluable when monitoring or debugging complex multicast setups
with bridges.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the IFLA_STATS_LINK_XSTATS_SLAVE attribute
which allows to export per-slave statistics if the master device supports
the linkxstats callback. The attribute is passed down to the linkxstats
callback and it is up to the callback user to use it (an example has been
added to the only current user - the bridge). This allows us to query only
specific slaves of master devices like bridge ports and export only what
we're interested in instead of having to dump all ports and searching only
for a single one. This will be used to export per-port IGMP/MLD stats and
also per-port vlan stats in the future, possibly other statistics as well.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a helper for changing skb->pkt_type in a controlled way.
We only allow a subset of possible values and can extend that in future
should other use cases come up. Doing this as a helper has the advantage
that errors can be handeled gracefully and thus helper kept extensible.
It's a write counterpart to pkt_type member we can already read from
struct __sk_buff context. Major use case is to change incoming skbs to
PACKET_HOST in a programmatic way instead of having to recirculate via
redirect(..., BPF_F_INGRESS), for example.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a minimal helper for doing the groundwork of changing
the skb->protocol in a controlled way. Currently supported is v4 to
v6 and vice versa transitions, which allows f.e. for a minimal, static
nat64 implementation where applications in containers that still
require IPv4 can be transparently operated in an IPv6-only environment.
For example, host facing veth of the container can transparently do
the transitions in a programmatic way with the help of clsact qdisc
and cls_bpf.
Idea is to separate concerns for keeping complexity of the helper
lower, which means that the programs utilize bpf_skb_change_proto(),
bpf_skb_store_bytes() and bpf_lX_csum_replace() to get the job done,
instead of doing everything in a single helper (and thus partially
duplicating helper functionality). Also, bpf_skb_change_proto()
shouldn't need to deal with raw packet data as this is done by other
helpers.
bpf_skb_proto_6_to_4() and bpf_skb_proto_4_to_6() unclone the skb to
operate on a private one, push or pop additionally required header
space and migrate the gso/gro meta data from the shared info. We do
mark the gso type as dodgy so that headers are checked and segs
recalculated by the gso/gro engine. The gso_size target is adapted
as well. The flags argument added is currently reserved and can be
used for future extensions.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use smp_processor_id() for the generic helper bpf_get_smp_processor_id()
instead of the raw variant. This allows for preemption checks when we
have DEBUG_PREEMPT, and otherwise uses the raw variant anyway. We only
need to keep the raw variant for socket filters, but we can reuse the
helper that is already there from cBPF side.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"I've been traveling so this accumulates more than week or so of bug
fixing. It perhaps looks a little worse than it really is.
1) Fix deadlock in ath10k driver, from Ben Greear.
2) Increase scan timeout in iwlwifi, from Luca Coelho.
3) Unbreak STP by properly reinjecting STP packets back into the
stack. Regression fix from Ido Schimmel.
4) Mediatek driver fixes (missing malloc failure checks, leaking of
scratch memory, wrong indexing when mapping TX buffers, etc.) from
John Crispin.
5) Fix endianness bug in icmpv6_err() handler, from Hannes Frederic
Sowa.
6) Fix hashing of flows in UDP in the ruseport case, from Xuemin Su.
7) Fix netlink notifications in ovs for tunnels, delete link messages
are never emitted because of how the device registry state is
handled. From Nicolas Dichtel.
8) Conntrack module leaks kmemcache on unload, from Florian Westphal.
9) Prevent endless jump loops in nft rules, from Liping Zhang and
Pablo Neira Ayuso.
10) Not early enough spinlock initialization in mlx4, from Eric
Dumazet.
11) Bind refcount leak in act_ipt, from Cong WANG.
12) Missing RCU locking in HTB scheduler, from Florian Westphal.
13) Several small MACSEC bug fixes from Sabrina Dubroca (missing RCU
barrier, using heap for SG and IV, and erroneous use of async flag
when allocating AEAD conext.)
14) RCU handling fix in TIPC, from Ying Xue.
15) Pass correct protocol down into ipv4_{update_pmtu,redirect}() in
SIT driver, from Simon Horman.
16) Socket timer deadlock fix in TIPC from Jon Paul Maloy.
17) Fix potential deadlock in team enslave, from Ido Schimmel.
18) Memory leak in KCM procfs handling, from Jiri Slaby.
19) ESN generation fix in ipv4 ESP, from Herbert Xu.
20) Fix GFP_KERNEL allocations with locks held in act_ife, from Cong
WANG.
21) Use after free in netem, from Eric Dumazet.
22) Uninitialized last assert time in multicast router code, from Tom
Goff.
23) Skip raw sockets in sock_diag destruction broadcast, from Willem
de Bruijn.
24) Fix link status reporting in thunderx, from Sunil Goutham.
25) Limit resegmentation of retransmit queue so that we do not
retransmit too large GSO frames. From Eric Dumazet.
26) Delay bpf program release after grace period, from Daniel
Borkmann"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (141 commits)
openvswitch: fix conntrack netlink event delivery
qed: Protect the doorbell BAR with the write barriers.
neigh: Explicitly declare RCU-bh read side critical section in neigh_xmit()
e1000e: keep VLAN interfaces functional after rxvlan off
cfg80211: fix proto in ieee80211_data_to_8023 for frames without LLC header
qlcnic: use the correct ring in qlcnic_83xx_process_rcv_ring_diag()
bpf, perf: delay release of BPF prog after grace period
net: bridge: fix vlan stats continue counter
tcp: do not send too big packets at retransmit time
ibmvnic: fix to use list_for_each_safe() when delete items
net: thunderx: Fix TL4 configuration for secondary Qsets
net: thunderx: Fix link status reporting
net/mlx5e: Reorganize ethtool statistics
net/mlx5e: Fix number of PFC counters reported to ethtool
net/mlx5e: Prevent adding the same vxlan port
net/mlx5e: Check for BlueFlame capability before allocating SQ uar
net/mlx5e: Change enum to better reflect usage
net/mlx5: Add ConnectX-5 PCIe 4.0 to list of supported devices
net/mlx5: Update command strings
net: marvell: Add separate config ANEG function for Marvell 88E1111
...
* fix mesh peer link counter, decrement wasn't always done at all
* fix ethertype (length) for packets without RFC 1042 or bridge
tunnel header
-----BEGIN PGP SIGNATURE-----
iQIcBAABCgAGBQJXc5wQAAoJEGt7eEactAAd2HQP/RS3lZaNn97spZp9Vb9Swqd6
UjhT4vHL2wHPMhPals2M2ztRhL8df/55tOhSuCwUki0gTsAfP4+Jz1PZ4okFUSBn
6EHvRtAgSAzjBElZVEsNO2sM/qm0UOnlqm4XpOXcKzpnRzDSlIa6vpnctp2MJMBI
PB46x8BPQoi192aTzleMqgBwjrMX1ohsM6rgOIEf7rvLhftx6LRRm7/uKaiwenVT
ZxkP6jIOs5ofkUHLHS4OPyId4yReO8oMMbRRA4fW1z2T8hME9PH3jTZL3Znaj7VF
s2LLSqwUlv06k0WFu3SzJh750jCJ6cnJiIqggDlPChrb0/DPicqgWR7/tJAvNVfj
WJqugeNtEVI+4ElGNxFzFAvjAKqO8fHY5U8Ko4LtZuwhjpo5GDvA+FErFESRXvCG
c647cDMhn+6OXwpUwsggQK4c+AS4QX/PzHjmhW5tKORPXlYVXAAz+JDXn195WnzV
w4UAO4ZWai9XY6oSc63uudaHMt8Xkmq8PRQsH1hHG20CAJ+7bGugaWVTci5fzeNh
JC4X+Xh6t+5qq1jEWgr+KguVKXtP3pVetqGy9kYQrJov0fTe2Z6deEeY08sH1Ffz
xdnQUsZphvqSkosTw76JtNPXz2ajxZCD3KNWjcpkL/NNs9lnIZPZc/mnzKP7ltro
ZEYw0HbcXVt/uFhHlwdG
=dAbs
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-06-29-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two small fixes
* fix mesh peer link counter, decrement wasn't always done at all
* fix ethertype (length) for packets without RFC 1042 or bridge
tunnel header
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first and last netlink message for a particular conntrack are
actually sent. The first message is sent through nf_conntrack_confirm when
the conntrack is committed. The last one is sent when the conntrack is
destroyed on timeout. The other conntrack state change messages are not
advertised.
When the conntrack subsystem is used from netfilter, nf_conntrack_confirm
is called for each packet, from the postrouting hook, which in turn calls
nf_ct_deliver_cached_events to send the state change netlink messages.
This commit fixes the problem by calling nf_ct_deliver_cached_events in the
non-commit case as well.
Fixes: 7f8a436eaa ("openvswitch: Add conntrack action")
CC: Joe Stringer <joestringer@nicira.com>
CC: Justin Pettit <jpettit@nicira.com>
CC: Andy Zhou <azhou@nicira.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Samuel Gauthier <samuel.gauthier@6wind.com>
Acked-by: Joe Stringer <joe@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_unshare() fails, we call qdisc_drop() with a NULL skb, which
is no longer supported.
Fixes: 520ac30f45 ("net_sched: drop packets after root qdisc lock is released")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
neigh_xmit() expects to be called inside an RCU-bh read side critical
section, and while one of its two current callers gets this right, the
other one doesn't.
More specifically, neigh_xmit() has two callers, mpls_forward() and
mpls_output(), and while both callers call neigh_xmit() under
rcu_read_lock(), this provides sufficient protection for neigh_xmit()
only in the case of mpls_forward(), as that is always called from
softirq context and therefore doesn't need explicit BH protection,
while mpls_output() can be called from process context with softirqs
enabled.
When mpls_output() is called from process context, with softirqs
enabled, we can be preempted by a softirq at any time, and RCU-bh
considers the completion of a softirq as signaling the end of any
pending read-side critical sections, so if we do get a softirq
while we are in the part of neigh_xmit() that expects to be run inside
an RCU-bh read side critical section, we can end up with an unexpected
RCU grace period running right in the middle of that critical section,
making things go boom.
This patch fixes this impedance mismatch in the callee, by making
neigh_xmit() always take rcu_read_{,un}lock_bh() around the code that
expects to be treated as an RCU-bh read side critical section, as this
seems a safer option than fixing it in the callers.
Fixes: 4fd3d7d9e8 ("neigh: Add helper function neigh_xmit")
Signed-off-by: David Barroso <dbarroso@fastly.com>
Signed-off-by: Lennert Buytenhek <lbuytenhek@fastly.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PDU length of incoming LLC frames is set to the total skb payload size
in __ieee80211_data_to_8023() of net/wireless/util.c which incorrectly
includes the length of the IEEE 802.11 header.
The resulting LLC frame header has a too large PDU length, causing the
llc_fixup_skb() function of net/llc/llc_input.c to reject the incoming
skb, effectively breaking STP.
Solve the problem by properly substracting the IEEE 802.11 frame header size
from the PDU length, allowing the LLC processor to pick up the incoming
control messages.
Special thanks to Gerry Rozema for tracking down the regression and proposing
a suitable patch.
Fixes: 2d1c304cb2 ("cfg80211: add function for 802.3 conversion with separate output buffer")
Cc: stable@vger.kernel.org
Reported-by: Gerry Rozema <gerryr@rozeware.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
I made a dumb off-by-one mistake when I added the vlan stats counter
dumping code. The increment should happen before the check, not after
otherwise we miss one entry when we continue dumping.
Fixes: a60c090361 ("bridge: netlink: export per-vlan stats")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Arjun reported a bug in TCP stack and bisected it to a recent commit.
In case where we process SACK, we can coalesce multiple skbs
into fat ones (tcp_shift_skb_data()), to lower write queue
overhead, because we do not expect to retransmit these packets.
However, SACK reneging can happen, forcing the sender to retransmit
all these packets. If skb->len is above 64KB, we then send buggy
IP packets that could hang TSO engine on cxgb4.
Neal suggested to use tcp_tso_autosize() instead of tp->gso_segs
so that we cook packets of optimal size vs TCP/pacing.
Thanks to Arjun for reporting the bug and running the tests !
Fixes: 10d3be5692 ("tcp-tso: do not split TSO packets at retransmit time")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Arjun V <arjun@chelsio.com>
Tested-by: Arjun V <arjun@chelsio.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Context implies that port in struct "udp_media_addr" is referring
to a UDP port.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP msg2addr function tipc_udp_msg2addr() can return -EINVAL which
prior to this patch was unhanded in the caller.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The space is missing before the open parenthesis '(', and this
will introduce much more noise when checking patch around.
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The untagged vlan object is only destroyed when the interface is removed
via the legacy sysfs interface. But it also has to be destroyed when the
standard rtnl-link interface is used.
Fixes: 5d2c05b213 ("batman-adv: add per VLAN interface attribute framework")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_linearize may reallocate the skb. This makes the calculated pointer
for ethhdr invalid. But it the pointer is used later to fill in the RR
field of the batadv_icmp_packet_rr packet.
Instead re-evaluate eth_hdr after the skb_linearize+skb_cow to fix the
pointer and avoid the invalid read.
Fixes: da6b8c20a5 ("batman-adv: generalize batman-adv icmp packet handling")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each batadv_tt_local_entry hold a single reference to a
batadv_softif_vlan. In case a new entry cannot be added to the hash
table, the error path puts the reference, but the reference will also
now be dropped by batadv_tt_local_entry_release().
Fixes: a33d970d0b ("batman-adv: Fix reference counting of vlan object for tt_local_entry")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tt_req_node is added and removed from a list inside a spinlock. But the
locking is sometimes removed even when the object is still referenced and
will be used later via this reference. For example batadv_send_tt_request
can create a new tt_req_node (including add to a list) and later
re-acquires the lock to remove it from the list and to free it. But at this
time another context could have already removed this tt_req_node from the
list and freed it.
CPU#0
batadv_batman_skb_recv from net_device 0
-> batadv_iv_ogm_receive
-> batadv_iv_ogm_process
-> batadv_iv_ogm_process_per_outif
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_ogm_receive
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_ogm_handler_v1
-> batadv_tt_update_orig
-> batadv_send_tt_request
-> batadv_tt_req_node_new
spin_lock(...)
allocates new tt_req_node and adds it to list
spin_unlock(...)
return tt_req_node
CPU#1
batadv_batman_skb_recv from net_device 1
-> batadv_recv_unicast_tvlv
-> batadv_tvlv_containers_process
-> batadv_tvlv_call_handler
-> batadv_tt_tvlv_unicast_handler_v1
-> batadv_handle_tt_response
spin_lock(...)
tt_req_node gets removed from list and is freed
spin_unlock(...)
CPU#0
<- returned to batadv_send_tt_request
spin_lock(...)
tt_req_node gets removed from list and is freed
MEMORY CORRUPTION/SEGFAULT/...
spin_unlock(...)
This can only be solved via reference counting to allow multiple contexts
to handle the list manipulation while making sure that only the last
context holding a reference will free the object.
Fixes: a73105b8d4 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Tested-by: Martin Weinelt <martin@darmstadt.freifunk.net>
Tested-by: Amadeus Alfa <amadeus@chemnitz.freifunk.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a VLAN tagged frame is received and the corresponding VLAN is not
configured on the soft interface, it will splat a WARN on every packet
received. This is a quite annoying behaviour for some scenarios, e.g. if
bat0 is bridged with eth0, and there are arbitrary VLAN tagged frames
from Ethernet coming in without having any VLAN configuration on bat0.
The code should probably create vlan objects on the fly and
transparently transport these VLAN-tagged Ethernet frames, but until
this is done, at least the WARN splat should be replaced by a rate
limited output.
Fixes: 354136bcc3 ("batman-adv: fix kernel crash due to missing NULL checks")
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge is falsly dropping ipv6 mulitcast packets if there is:
1. No ipv6 address assigned on the brigde.
2. No external mld querier present.
3. The internal querier enabled.
When the bridge fails to build mld queries, because it has no
ipv6 address, it slilently returns, but keeps the local querier enabled.
This specific case causes confusing packet loss.
Ipv6 multicast snooping can only work if:
a) An external querier is present
OR
b) The bridge has an ipv6 address an is capable of sending own queries
Otherwise it has to forward/flood the ipv6 multicast traffic,
because snooping cannot work.
This patch fixes the issue by adding a flag to the bridge struct that
indicates that there is currently no ipv6 address assinged to the bridge
and returns a false state for the local querier in
__br_multicast_querier_exists().
Special thanks to Linus Lüssing.
Fixes: d1d81d4c3d ("bridge: check return value of ipv6_dev_get_saddr()")
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a user space program (e.g., wpa_supplicant) deletes a STA entry that
is currently in NL80211_PLINK_ESTAB state, the number of established
plinks counter was not decremented and this could result in rejecting
new plink establishment before really hitting the real maximum plink
limit. For !user_mpm case, this decrementation is handled by
mesh_plink_deactive().
Fix this by decrementing estab_plinks on STA deletion
(mesh_sta_cleanup() gets called from there) so that the counter has a
correct value and the Beacon frame advertisement in Mesh Configuration
element shows the proper value for capability to accept additional
peers.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Drop redundant include of moduleparam.h
The Coccinelle semantic patch used to make this change is as follows:
@ includesmodule @
@@
#include <linux/module.h>
@ depends on includesmodule @
@@
- #include <linux/moduleparam.h>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to inet_diag facility to filter sockets based on device
index. If an interface index is in the filter only sockets bound
to that index (sk_bound_dev_if) are returned.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes wrong-interface signaling on 32-bit platforms for entries
created when jiffies > 2^31 + MFC_ASSERT_THRESH.
Signed-off-by: Tom Goff <thomas.goff@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several places where the listener and pending or accept queue
child sockets are accessed at the same time. Lockdep is unhappy that
two locks from the same class are held.
Tell lockdep that it is safe and document the lock ordering.
Originally Claudio Imbrenda <imbrenda@linux.vnet.ibm.com> sent a similar
patch asking whether this is safe. I have audited the code and also
covered the vsock_pending_work() function.
Suggested-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
with the commit 8c14586fc3 ("net: ipv6: Use passed in table for
nexthop lookups"), net hop lookup is first performed on route creation
in the passed-in table.
However device match is not enforced in table lookup, so the found
route can be later discarded due to egress device mismatch and no
global lookup will be performed.
This cause the following to fail:
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip route add 2001:db8:8086::/48 dev dummy1 metric 20
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy1 metric 20
ip route add 2001:db8:8086::/48 dev dummy2 metric 21
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy2 metric 21
RTNETLINK answers: No route to host
This change fixes the issue enforcing device lookup in
ip6_nh_lookup_table()
v1->v2: updated commit message title
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Reported-and-tested-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJXa6rGAAoJED07qiWsqSVqzwsH/0g/blikQuNNAB7LzXGTEMn8
ipWCODaYxgWE/V/1A0JjsKpxB1ZL3HE0/xg/OmZ10SRNlz5LJTLkoYZa7xYmyxtT
a89mT9vdnWxwfwbeIhSSjG9W9g44vqrhMIPxffIu5yqSqdIJak0HIiuQizJ0/xjx
xQVx4AykWKQ3u0/Tiyz3ez5yhyMMNEmHxKyDWpgrR6+zXlofwP/Em3NFPwk9gh32
ECAagOUOEvdjXeRs1Yn/CV0FC7Wgs4Hzr048JJ5wOteawBLr+sPOnuWZtDhNrwDK
Eceh7aEeAiFfIW+jCMEe5qrpFHi8hqyqBo4L9TDYsE7T/Z6BPyh+5OUh8+5dtaw=
=TZew
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.8-20160623' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2016-06-17
this is a pull request of 4 patches for net-next/master.
Arnd Bergmann's patch fixes a regresseion in af_can introduced in
linux-can-next-for-4.8-20160617. There are two patches by Ramesh
Shanmugasundaram, which add CAN-2.0 support to the rcar_canfd driver.
And a patch by Ed Spiridonov that adds better error diagnoses messages
to the Ed Spiridonov driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
