stmmac_mac_config_rx_queues_routing() incorrectly calls rx_queue_prio()
instead of rx_queue_routing().
This looks like a copy paste issue, since
stmmac_mac_config_rx_queues_prio() already calls rx_queue_prio(),
and both stmmac_mac_config_rx_queues_routing() and
stmmac_mac_config_rx_queues_prio() are very similar in structure.
Fixes: abe80fdc6e ("net: stmmac: RX queue routing configuration")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looking at dwmac4_tx_queue_routing(), it is obvious that it
sets up rx queue routing.
Rename dwmac4_tx_queue_routing() to dwmac4_rx_queue_routing()
to better match reality.
Fixes: abe80fdc6e ("net: stmmac: RX queue routing configuration")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code assumes that a tx_skbuff entry has been cleared
by stmmac_tx_clean() before stmmac_xmit()/stmmac_tso_xmit()
assigns a new skb to that entry. However, since we never check
the current value before overwriting it, it is theoretically
possible that a non-NULL value is overwritten.
Add WARN_ONs to verify that each entry in tx_skbuff is NULL
before it is assigned a new value.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_skbuff is initialized to NULL in init_dma_tx_desc_rings(), which is
called from ndo_open().
stmmac_tx_clean() frees any non-NULL skb, and sets the tx_skbuff
entry to NULL. Hence, there is no need to set skbuff entries to NULL
in stmmac_xmit()/stmmac_tso_xmit(), and doing so falsely gives the
reader the impression that it is needed.
Do not clear tx_skbuff entries in stmmac_xmit()/stmmac_tso_xmit().
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMA engine in dwmac4 can segment a large TSO packet to several
smaller packets of (max) size Maximum Segment Size (MSS).
The DMA engine fetches and saves the MSS via a context descriptor.
This context decriptor has to be provided to each tx DMA channel.
To ensure that this is done, move struct member mss from stmmac_priv
to stmmac_tx_queue.
stmmac_reset_queues_param() now also resets mss, together with other
queue parameters, so reset of mss value can be removed from
stmmac_resume().
init_dma_tx_desc_rings() now also resets mss, together with other
queue parameters, so reset of mss value can be removed from
stmmac_open().
This fixes tx queue timeouts for dwmac4, with DT property
snps,tx-queues-to-use > 1, when running iperf3 with multiple threads.
Fixes: ce736788e8 ("net: stmmac: adding multiple buffers for TX")
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for calculating occupancy for separate kvdl parts.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for dynamic partition set via the resource interface.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The linear part of the KVD memory is sub-divided into multiple parts. This
patch exposes this internal partitions via the resource interface.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding size validation logic into core cleanup is required.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supplementary TX descriptors were not being accounted for, which
was resulting in an overflow of the hardware device's transmit
queue. Keep track of those descriptors now when determining
how many entries remain on the TX queue.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ungraceful host shutdown or driver crash case BMC connectivity is
lost. APE firmware is missing the driver state in this
case to keep the BMC connectivity alive.
This patch has below change to address this issue.
Heartbeat mechanism with APE firmware. This heartbeat mechanism
is needed to notify the APE firmware about driver state.
This patch also has the change in wait time for APE event from
1ms to 20ms as there can be some delay in getting response.
v2: Drop inline keyword as per David suggestion.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADVERTISED_Asym_Pause bit was being improperly set when both
rx and tx pause were enabled. When rx and tx are both enabled, only
the ADVERTISED_Pause bit is supposed to be set.
Signed-off-by: Jake Moroni <mail@jakemoroni.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The *while* loop in this function can be turned into a normal *for* loop.
And getting rid of the single return point saves us a few more LoCs...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The common clock framework needs access to the "clock configuration"
structs during runtime.
However, only the common clock framework should access these. Ensure
this by moving the configuration structs out of struct meson8b_dwmac,
so only meson8b_init_rgmii_tx_clk() and the common clock framework know
about these configurations.
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing in the dwmac-meson8b driver (except .probe itself) requires the
platform_device anymore after .probe has finished. Replace it with a
pointer to struct device since this is what the functions inside the
driver are actually accessing.
No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To goal of this patch is to simplify the registration of the RGMII TX
clock (and it's parent clocks). This is achieved by:
- introducing the meson8b_dwmac_register_clk helper-function to remove
code duplication when registering a single clock (this saves a few
lines since we have 4 clocks internally)
- using devm_add_action_or_reset to disable the RGMII TX clock
automatically when needed. This also allows us to re-use the standard
stmmac_pltfr_remove function.
- devm_kasprintf() and devm_kstrdup() are not used anymore to generate
the clock name (these are replaced by a variable on the stack) because
the common clock framework already uses kstrdup() internally.
No functional changes intended.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mlxsw replaces (or deletes) a route it removes the offload
indication from the replaced route. This is problematic for IPv4 routes,
as the offload indication is stored in the fib_info which is usually
shared between multiple routes.
Instead of unconditionally clearing the offload indication, only clear
it if no other route is using the fib_info.
Fixes: 3984d1a89f ("mlxsw: spectrum_router: Provide offload indication using nexthop flags")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a command packet with invalid mux id is received, the packet would
not have a valid endpoint. This invalid endpoint maybe dereferenced
leading to a crash. Identified by manual code inspection.
Fixes: 3352e6c457 ("net: qualcomm: rmnet: Convert the muxed endpoint to hlist")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_DEBUG_PREEMPT enabled, a crash with the following call
stack was observed when removing a real dev which had rmnet devices
attached to it.
To fix this, remove the netdev_upper link APIs and instead use the
existing information in rmnet_port and rmnet_priv to get the
association between real and rmnet devs.
BUG: sleeping function called from invalid context
in_atomic(): 0, irqs_disabled(): 0, pid: 5762, name: ip
Preemption disabled at:
[<ffffff9d49043564>] debug_object_active_state+0xa4/0x16c
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
PC is at ___might_sleep+0x13c/0x180
LR is at ___might_sleep+0x17c/0x180
[<ffffff9d48ce0924>] ___might_sleep+0x13c/0x180
[<ffffff9d48ce09c0>] __might_sleep+0x58/0x8c
[<ffffff9d49d6253c>] mutex_lock+0x2c/0x48
[<ffffff9d48ed4840>] kernfs_remove_by_name_ns+0x48/0xa8
[<ffffff9d48ed6ec8>] sysfs_remove_link+0x30/0x58
[<ffffff9d49b05840>] __netdev_adjacent_dev_remove+0x14c/0x1e0
[<ffffff9d49b05914>] __netdev_adjacent_dev_unlink_lists+0x40/0x68
[<ffffff9d49b08820>] netdev_upper_dev_unlink+0xb4/0x1fc
[<ffffff9d494a29f0>] rmnet_dev_walk_unreg+0x6c/0xc8
[<ffffff9d49b00b40>] netdev_walk_all_lower_dev_rcu+0x58/0xb4
[<ffffff9d494a30fc>] rmnet_config_notify_cb+0xf4/0x134
[<ffffff9d48cd21b4>] raw_notifier_call_chain+0x58/0x78
[<ffffff9d49b028a4>] call_netdevice_notifiers_info+0x48/0x78
[<ffffff9d49b0b568>] rollback_registered_many+0x230/0x3c8
[<ffffff9d49b0b738>] unregister_netdevice_many+0x38/0x94
[<ffffff9d49b1e110>] rtnl_delete_link+0x58/0x88
[<ffffff9d49b201dc>] rtnl_dellink+0xbc/0x1cc
[<ffffff9d49b2355c>] rtnetlink_rcv_msg+0xb0/0x244
[<ffffff9d49b5230c>] netlink_rcv_skb+0xb4/0xdc
[<ffffff9d49b204f4>] rtnetlink_rcv+0x34/0x44
[<ffffff9d49b51af0>] netlink_unicast+0x1ec/0x294
[<ffffff9d49b51fdc>] netlink_sendmsg+0x320/0x390
[<ffffff9d49ae6858>] sock_sendmsg+0x54/0x60
[<ffffff9d49ae6f94>] ___sys_sendmsg+0x298/0x2b0
[<ffffff9d49ae98f8>] SyS_sendmsg+0xb4/0xf0
[<ffffff9d48c83770>] el0_svc_naked+0x24/0x28
Fixes: ceed73a2cf ("drivers: net: ethernet: qualcomm: rmnet: Initial implementation")
Fixes: 60d58f971c ("net: qualcomm: rmnet: Implement bridge mode")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow for changing the MTU within the limit of the maximum size of a
descriptor (2048 bytes). Add the callback to change MTU from user-space
and take the configurable MTU into account when configuring the
hardware.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement tcp flag match offloading. Current tcp flag match support include
FIN, SYN, RST, PSH and URG flags, other flags are unsupported. The PSH and
URG flags are only set in the hardware fast path when used in combination
with the SYN, RST and PSH flags.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nfp_net_ctrl.h file used spaces for indentation in the past but
tabs have crept in. Host driver files use tabs for indentation by
default, so let's convert to tabs for consistency across the file
and our drivers.
Signed-off-by: Michael Rapson <michael.rapson@netronome.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've run into a problem where our device is attached
to a Virtual Machine and the use of the new pci_set_vpd_size()
API doesn't help. The VM kernel has been informed that
the accesses are okay, but all of the actual VPD Capability
Accesses are trapped down into the KVM Hypervisor where it
goes ahead and imposes the silent denials.
The right idea is to follow the kernel.org
commit 1c7de2b4ff ("PCI: Enable access to non-standard VPD for
Chelsio devices (cxgb3)") which Alexey Kardashevskiy authored
to establish a PCI Quirk for our T3-based adapters. This commit
extends that PCI Quirk to cover Chelsio T4 devices and later.
The advantage of this approach is that the VPD Size gets set early
in the Base OS/Hypervisor Boot and doesn't require that the cxgb4
driver even be available in the Base OS/Hypervisor. Thus PF4 can
be exported to a Virtual Machine and everything should work.
Fixes: 67e658794c ("cxgb4: Set VPD size so we can read both VPD structures")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set correct size of the CIM LA dump for T6.
Fixes: 27887bc7cb ("cxgb4: collect hardware LA dumps")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
free pf 0-3 resources, commit baf5086840 ("cxgb4:
restructure VF mgmt code") erroneously removed the
code which frees the pf 0-3 resources, causing the
probe of pf 0-3 to fail in case of driver reload.
Fixes: baf5086840 ("cxgb4: restructure VF mgmt code")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-02-14
This patch series enables the new mqprio hardware offload mechanism
creating traffic classes on VFs for XL710 devices. The parameters
needed to configure these traffic classes/queue channels are provides
by the user via the tc tool. A maximum of four traffic classes can be
created on each VF. This patch series also enables application of cloud
filters to each of these traffic classes. The cloud filters are applied
using the tc-flower classifier.
Example:
1. tc qdisc add dev vf0 root mqprio num_tc 4 map 0 0 0 0 1 2 2 3\
queues 2@0 2@2 1@4 1@5 hw 1 mode channel
2. tc qdisc add dev vf0 ingress
3. ethtool -K vf0 hw-tc-offload on
4. ip link set eth0 vf 0 spoofchk off
5. tc filter add dev vf0 protocol ip parent ffff: prio 1 flower dst_ip\
192.168.3.5/32 ip_proto udp dst_port 25 skip_sw hw_tc 2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Use readq() (via t4_read_reg64()) to read 64-bits at a time.
Read residual in 32-bit multiples.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework logic to read EDC and MC. Do 32-bit reads at a time.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device close or reset, there were some cases of outstanding
RX socket buffers not being freed. Include a function similar to the
one that already exists to clean TX socket buffers in this case.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a RX buffer is returned to the client driver with an error, free the
corresponding socket buffer before continuing.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This memory is allocated during initialization but never freed,
so do that now.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device bringup, the driver exchanges login buffers with
firmware. These buffers contain information such number of TX
and RX queues alloted to the device, RX buffer size, etc. These
buffers weren't being properly freed on device reset or close.
We can free the buffer we send to firmware as soon as we get
a response. There is information in the response buffer that
the driver needs for normal operation so retain it until the
next reset or removal.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pushes back setting the carrier on until the end of the reset
code. This resolves a bug where a watchdog timer was detecting
that a TX queue had stalled before the adapter reset was complete.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit aa136d0c82.
As I previously[1] pointed out this implementation of XDP_REDIRECT is
wrong. XDP_REDIRECT is a facility that must work between different
NIC drivers. Another NIC driver can call ndo_xdp_xmit/nicvf_xdp_xmit,
but your driver patch assumes payload data (at top of page) will
contain a queue index and a DMA addr, this is not true and worse will
likely contain garbage.
Given you have not fixed this in due time (just reached v4.16-rc1),
the only option I see is a revert.
[1] http://lkml.kernel.org/r/20171211130902.482513d3@redhat.com
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Christina Jacob <cjacob@caviumnetworks.com>
Cc: Aleksey Makarov <aleksey.makarov@cavium.com>
Fixes: aa136d0c82 ("net: thunderx: Add support for xdp redirect")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides support to add or delete cloud filter for queue
channels created for ADq on VF.
We are using the HW's cloud filter feature and programming it to act
as a TC filter applied to a group of queues.
There are two possible modes for a VF when applying a cloud filter
1. Basic Mode: Intended to apply filters that don't need a VF to be
Trusted. This would include the following
Dest MAC + L4 port
Dest MAC + VLAN + L4 port
2. Advanced Mode: This mode is only for filters with combination that
requires VF to be Trusted.
Dest IP + L4 port
When cloud filters are applied on a trusted VF and for some reason
the same VF is later made as untrusted then all cloud filters
will be deleted. All cloud filters has to be re-applied in
such a case.
Cloud filters are also deleted when queue channel is deleted.
Testing-Hints:
=============
1. Adding Basic Mode filter should be possible on a VF in
Non-Trusted mode.
2. In Advanced mode all filters should be able to be created.
Steps:
======
1. Enable ADq and create TCs using TC mqprio command
2. Apply cloud filter.
3. Turn-off the spoof check.
4. Pass traffic.
Example:
========
1. tc qdisc add dev enp4s2 root mqprio num_tc 4 map 0 0 0 0 1 2 2 3\
queues 2@0 2@2 1@4 1@5 hw 1 mode channel
2. tc qdisc add dev enp4s2 ingress
3. ethtool -K enp4s2 hw-tc-offload on
4. ip link set ens261f0 vf 0 spoofchk off
5. tc filter add dev enp4s2 protocol ip parent ffff: prio 1 flower\
dst_ip 192.168.3.5/32 ip_proto udp dst_port 25 skip_sw hw_tc 2
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables a tc filter to be applied as a cloud
filter for the VF. This patch adds functions which parse the
tc filter, extract the necessary fields needed to configure the
filter and package them in a virtchnl message to be sent to the
PF to apply them.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch handles the request from ADq enabled VF to allocate
bandwidth to each traffic class which means for each VSI.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support to configure bandwidth for the traffic
classes via tc tool. The required information is passed to the PF
which is used in the process of setting up the traffic classes.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch takes care of freeing up all the VSIs, queues and
other ADq related software and hardware resources, when a user
requests for deletion of ADq on VF.
Example command:
tc qdisc del dev eth0 root
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch allocates number of queues requested by the user as a part
of TC command when ADq is enabled on a VF.
In order to be consistent in design with PF implementation of ADq,
don't allow to set channels via ethtool from VF when ADq is already
enabled. This means the users will not be able to change the number of
queues/channels via ethtool for a VF when ADq is ON. In order to be
able to use set channels, users will be required to disable ADq first
and then try setting the channels again.
When ADq is enabled on VF, it goes through a reset during which VSIs
and queues are re-configured. Meanwhile if we receive link status
message from PF even before the queues are re-configured, just ignore
this link up message.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables ADq and creates queue channels on a VF. An ADq
enabled VF can have up to 4 VSIs and each one of them represents
a traffic class and this is termed as a queue channel. Each of these
VSIs can have up to 4 queues. This patch services the request for
enabling ADq and adds queue channel based on the TC mqprio info
provided by the user in the VF.
Initially a check is made to see if spoof check is OFF, if not ADq
will not be enabled. PF notifies VF for a reset in order to complete
the creation of ADq resources i.e. creation of additional VSIs and
allocation of queues as per TC information, all in the reset path.
Steps:
======
1. Turn off the spoof check
2. Enable ADq using tc mqprio command with or without rate limit.
3. Pass traffic.
Example:
========
% ip link set dev eth0 vf 0 spoofchk off
% tc qdisc add dev $iface root mqprio num_tc 4 map\
0 0 0 0 1 1 1 1 2 2 2 2 3 3 3 3 queues\
4@0 4@4 4@8 4@8 hw 1 mode channel
Expected results:
=================
1. Total number of queues for the VF should be sum of queues of all TCs.
2. Traffic flow should be normal without errors.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces the callback to the ndo_setup_tc function
in the VF driver. We add a wrapper function to make room for the
upcoming cloud filter patches which add calls to different functions
from setup_tc.
First, we add support for capability exchange for ADQ between the
PF and VF. Next, we add support to take in the mqprio configuration
and configure queues as per the traffic classes, rate limit and the
priorities specified by the user. This is done by passing the channel
config to the PF driver through a virtchannel message.
The flags and bits added, track if ADq is enabled, set max number of
traffic classes to 4 and provide ability to negotiate capability with
the PF.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One of the previous patch fixes the link up issue by ignoring it if
i40evf is not in __I40EVF_RUNNING state. However this doesn't fix the
race condition when queues are disabled esp for ADq on VF. Hence check
if all queues are enabled before starting all queues.
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the PF resets the VF, the VF puts out a warning message
indicating that the VF received a reset message from the PF.
Make this message more clear so that we do not mistakenly
think that the PF is undergoing a reset.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to changes done to the PF driver in commit 6622f5cdba ("i40e:
make use of __dev_uc_sync and __dev_mc_sync"), replace our
home-rolled method for updating the internal status of MAC filters with
__dev_uc_sync and __dev_mc_sync.
These new functions use internal state within the netdev struct in order
to efficiently break the question of "which filters in this list need to
be added or removed" into singular "add this filter" and "delete this
filter" requests.
This vastly improves our handling of .set_rx_mode especially with large
number of MAC filters being added to the device, and even results in
a simpler .set_rx_mode handler.
Under some circumstances, such as when attached to a bridge, we may
receive a request to delete our own permanent address. Prevent deletion
of this address during i40evf_addr_unsync so that we don't accidentally
stop receiving traffic.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The MAC, FW Version and NPAR check used to determine
if shutting off the FW LLDP engine is supported is not
using the usual feature check mechanism.
This patch fixes the problem by moving the feature check
to i40e_sw_init in order to set a flag in pf->hw_features
that ethtool will use for priv_flags disable operation.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Broadcast filters can now cause overflow promiscuous to trigger when
adding "too many" VLANs to all the ports of a device and the driver
needs a way to exit overflow promiscuous once triggered.
Currently the driver looks to see if there are "too many" filters and/or
we have any failed filters to determine when it is safe to exit overflow
promiscuous. If we trigger overflow promiscuous with broadcast filters,
any new filters added will be "auto-failed" until we exit overflow
promiscuous. Since the user can't manually remove the failed broadcast
filters for VLANs (nor should we expect the user to do such), there is
no way to exit overflow promiscuous without reloading the driver.
The easiest way to do this is to remove the shortcut to "auto-fail"
filters in overflow promiscuous. If the user removes the VLANs, the
failed filters will be removed and since we're no longer "auto-failing"
new filters, we'll eventually get a good set of filters and exit
overflow promiscuous.
This has the side benefit of making filter state more explicit in that
if a filter says it's failed we know for a fact it failed and not just
assuming it will if we're in overflow promiscuous. This is nice because
if the user removes some filters and then adds some, even if we're in
overflow promiscuous, the filter might succeed; we were just assuming it
won't because the user hasn't rectified other existing failed filters.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This code here is quite complex and easy to screw up. Let's see if we
can't improve the readability and maintainability a bit. This refactors
out promisc_changed into two variables 'old_overflow' and 'new_overflow'
which makes it a bit clearer when we're concerned about when and how
overflow promiscuous is changed. This also makes so that we no longer
need to pass a boolean pointer to i40e_aqc_add_filters. Instead we can
simply check if we changed the overflow promiscuous flag since the
function start.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
