This patch adds warnings when a reset of the adapter is scheduled so that the
user can see log of why the reset occurred.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch copies the igb implementation of Tx timestamps, which uses a work
item to poll for the Tx timestamp. In addition it adds a timeout value of 15
seconds, after which it will stop polling.
This is necessary due to an issue with the descriptor being marked done before
the Tx timestamp event has occurred. These two events don't correlate, so using
the done bit on the descriptor as indication that the timestamp must already
have been taken leads to potentially dropped Tx timestamps (especially under
heavy packet load)
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes ixgbe_ptp_match, and the corresponding packet filtering from
ixgbe driver. This code was previously causing some issues within the hotpath of
the driver. However the code also provided a check against possible frozen Rx
timestamp due to dropped packets when the Rx ring is full. This patch provides a
replacement solution based on the watchdog.
To this end, whenever a packet consumes the Rx timestamp it stores the jiffy
value in the rx_ring structure. Watchdog updates its own jiffy timer whenever
there is no valid timestamp in the registers.
If watchdog detects a valid timestamp in the registers, (meaning that no Rx
packet has consumed it yet) it will check which time is most recent, the last
time in the watchdog, or any time in the rx_rings. If the most recent "event"
was more than 5seconds ago, it will flush the Rx timestamp and print a warning
message to the syslog.
Reported-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the comment on ptp_overflow_check to match up with what is
currently used as the parameters. Also change the jiffies check to use
time_is_after_jiffies macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the filters for ethtool's get_ts_info to return support for
all filters which can be supported by upscaling to ptp_v2_event. The intent
behind this change is due to reasoning that we do in fact support the
filters. (hwtstamp_ioctl returns success after setting the filter to the
upscaled version). In this way we can remain consistent over which filters are
supported via the get_ts_info ioctl and which filters are in practice actually
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the ethtool diagnostics test by ensuring that the tests
work properly regardless of what state the adapter was in. The SRIOV VF check is
done at the beginning, forgoing the link test. The if_running -> dev_close is
moved before the link test, as well as a call to enable the Tx laser. This
ensures that the link test will return valid results even when adapter was
previously down. Also, a call to disable the Tx laser is added if the device
was down before the start. This ensures consistent behavior of the Tx laser
before and after the diagnostic checks. The end result is consistent behavior
regardless of device state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When posting a message on the bulletin board, the PF calculates crc
over the message and places the result in the message. When the VF
samples the Bulletin Board it copies the message aside and validates
this crc. The length of the message is crucial here and must be the
same in both parties. Since the PF is running in the Hypervisor and
the VF is running in a Vm, they can possibly be of different versions.
As the Bulletin Board is designed to grow forward in future versions,
in the VF the length must not be the size of the message structure
but instead it should be a field in the message itself.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 823e1d9 caused bnx2x to fail once BNX2X_STOP_ON_ERROR is set.
Fixes compilation by moving function declarations between header files.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In INTA mode, cnic and bnx2x share the same IRQ. During chip reset,
for example, cnic will stop servicing IRQs after it has shutdown the
cnic hardware resources. However, the shared IRQ is still active as
bnx2x needs to finish the reset. There is a window when bnx2x does
not know that cnic is no longer handling IRQ and things don't always
work properly.
Add a flag to tell bnx2x that cnic is handling IRQ. The flag is set
before the first cnic IRQ is expected and cleared when no more cnic
IRQs are expected, so there should be no race conditions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an incorrect SR-IOV memory release which was committed in 1ab4434.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove most of the sparse warnings in the bnx2x compilation
(i.e., thus resulting when compiling with `C=2 CF=-D__CHECK_ENDIAN__').
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't unload the bnx2x driver if its in a recovery process, or if
the previous load have failed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 15192a8cf there have been a memory leak upon rmmod
of the bnx2x driver.
This corrects the memory leak and corrects the zeroing of internal
memories upon driver load.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing 57712_VF and 57800_VF to CHIP_IS_E2 and CHIP_IS_E3
macros (missing from commit 8395be5).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add/Revise several debug prints in the bnx2x driver - on regular flows
as well as error flows.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the incorrect usage of `usleep_range(1000, 1000)' into
`usleep_range(1000, 2000)'.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slightly changes the bnx2x code without `true' functional changes.
Changes include:
1. Gathering macros into a single macro when combination is used multiple
times.
2. Exporting parts of functions into their own functions.
3. Return values after if-else instead of only on the else condition
(where current flow would simply return same value later in the code)
4. Removing some unnecessary code (either dead-code or incorrect conditions)
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly corrects white spaces, indentations, and comments.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reactivate promiscuous mode in H/W upon gfar_init_mac(), if the
net dev requires it (IFF_PROMISC flag set).
This way the promisc mode is preserved accross device reset conditions
like tx timeout, device restore, a.s.o.
Signed-off-by: Voncken C Acksys <cedric.voncken@acksys.fr>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes it is useful to be able to change the MAC address of the
interface for netback devices. For example, when using ebtables it may
be useful to be able to distinguish traffic from different interfaces
without depending on the interface name.
Reported-by: Nikita Borzykh <sample.n@gmail.com>
Reported-by: Paul Harvey <stockingpaul@hotmail.com>
Cc: netdev@vger.kernel.org
Cc: xen-devel@lists.xen.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Matt Wilson <msw@amazon.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last update to the Ethernet HowTo (over 10 years ago) listed this:
------------------------
SEEQ 8005
Status: Obsolete, Driver Name: seeq8005
There is little information about the card included in the driver,
and hence little information to be put here. If you have a question,
you are probably best trying to e-mail the driver author as listed
in the source.
It was marked obsolete as of the 2.4 series kernels.
------------------------
If it was obsolete over a decade ago, the situation can not have
improved with the passage of time, so let us act on that. Even with
today's improved search engines, I was unable to locate any real
meaningful information on the ISA implementation of this rare chip.
There are ARM and SGI variants of the driver in tree, but they do
not depend on the original x86 driver source or header file. We
leave those non-x86 drivers to be deleted by the arch maintainers
when they decide to expire those legacy platforms as a whole.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is another one that makes sense to target for obsolescence, since
it (a)appeared pre-1995, and (b)was rather rare, and (c)did not
really have any statistically significant active linux user base.
Removing this ISA 10Mbit driver support is unlikely to be even noticed
by the user base of 3.9+ linux kernels, especially when the documentation
clearly indicates the vintage with this text:
"...designed to work with all kernels > 1.1.33"
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These are old ISA 10Mbit cards from the 1st 1/2 of the 1990s and
required manual jumper settings in order to configure them. Here
we remove them on the premise that they are no longer used in any
modern 3.9+ kernels.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is an area I know all too well, after being author of several 8390
drivers, and maintainer of all 8390 drivers during a large part of their
active lifecycle.
To that end, I can say this with a reasonable degree of confidence.
The drivers deleted here represent the earliest (as in early 1990)
hardware and/or rare hardware. The remaining hardware not deleted
here is the more modern/sane of the lot, with ISA-PnP and jumperless
"soft configuration" like the wd and smc cards had.
The original ne2000 driver (ne.c) gets a pass at this time since
AT/LANTIC based cards that could be both ne2000 or wd-like (with
shared memory) and with jumperless configuration were made in the
mid to late 1990's, and performed reasonably well for their era.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is another driver for relatively rare 10Mbit hardware that
originated in the early 1990's. So we select it for removal at
this point in time as well.
Cc: Mika Kuoppala <miku@iki.fi>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These Fujitsu MB86965 based ISA 10Mbit cards were another of the
relatively rare cards dating from the early 1990s that for one reason
or another didn't seem to get a lot of use in linux. So we retire it
now with a reasonable degree of confidence that it won't impact anyone.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These cards were only available in 8bit format, and in addition
they only had AUI and BNC(10-Base2) interfaces (i.e. no RJ-45).
In fact, they are so rare, that an internet search on these old
cards almost comes up empty, unless the "Micom interlan" name
is used.
This puts them in the equivalent domain as the 3c501, so there
should be no strong opposition to the driver removal, as nobody
is seriously using 3.9+ with 8 bit ISA hardware.
In doing so, the whole "ethernet/racal" category becomes empty,
so we clean up the Makefile/Kconfig and subdir appropriately.
Cc: Andreas Mohr <andi@lisas.de>
Cc: Jan-Pascal van Best <janpascal@vanbest.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Like the other drivers that were in the ISA i825xx family, the ni52
was rather rare, not widely used, and hence perhaps not as reliable
as the more mainstream ISA drivers that were heavily used. Given
that, it is chosen for retirement at this time as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This driver supported early to mid 1990's Zenith laptops, of the
2" thick variety. The driver was already dead 10+ years ago, but
we see this in the source:
----------------
/* 10/2002
[...]
Tested on a vintage Zenith Z-Note 433Lnp+. Probably broken on
anything else. Testers (and detailed bug reports) are welcome :-).
----------------
To clarify, a 433 translates into a 486 at 33MHz, and a system with
a default of 4MB RAM. I can't fault the noble effort to keep things
working a decade ago, but at this point in time, there is no valid
justification to continue carrying this driver along.
Note that there is no associated Space.c cleanup here since this
driver was using module_init to hook itself in.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These old drivers should not be confused with the very common PCI
cards that are supported by e100.c -- these older 10Mbit ISA only
drivers were not as commonly used as some of the other ISA drivers,
simply due to hardware availability and pricing.
Given the rarity of the hardware, and the subsequent less extensive
use of the drivers, it makes sense to obsolete them at this point
in time, along with other rare/experimental ISA drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
For those of us who were around in the early to mid 1990's, we
will remember that the i825xx ethernet support was not something
that was considered sufficiently vetted for 24/7 use.
Folks might be inclined to use *functional* ISA hardware on some
near expired P3 ISA machines for dedicated workhorse applications,
but the odds of using (and relying on) one of these old/experimental
drivers is essentially nil. So lets remove them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The parallel port is largely replaced by USB, and even in the
day where these drivers were current, the documented speed was
less than 100kB/s. Let us not pretend that anyone cares about
these drivers anymore, or worse - pretend that anyone is using
them on a modern kernel.
As a side bonus, this is the end of legacy parallel port ethernet,
so we get to drop the whole chunk relating to that in the legacy
Space.c file containing the non-PCI unified probe dispatch.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It was amusing that linux was able to make use of this 1980's
technology on machines long past its intended lifespan, but
it probably should go now.
To set some context, the 3c501 was designed in the 1980's to be
used on 8088 PC-XT 8bit ISA machines. It was built using a large
number of discrete TTL components and truly looks like a relic
of the ancient past before large scale integration was common.
But from a functional point of view, the real issue, as stated
in the (also obsolete) Ethernet-HowTo, is that "...the 3c501 can
only do one thing at a time -- while you are removing one packet
from the single-packet buffer it cannot receive another packet,
nor can it receive a packet while loading a transmit packet."
You know things are not good when the Kconfig help text suggests
you make a cron job doing a ping every minute.
Hardware that old and crippled is simply not going to be used by
anyone in a time where 10 year old 100Mbit PCI cards (that are
still functional) are largely give-away items.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This driver was specific to a "professional workstation" line
of products from around 1993 that used the i82596 ethernet chip
as an on-board ethernet solution.
With a 486 processor, and the premium top of the line model maxing
out at a clock speed of 50MHz, we can safely retire this support.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The Apricot was a 486 PC with 4MB RAM, and an on-board ethernet
via an intel i82596 hard-wired to i/o 0x300.
Those who were using linux in the 1990's will recall that the
i82596 driver was not one of the more stable or widely used
drivers of its day. Combine that with the extremely limited
resources of the platform, and it is truly time to expire the
support for this thing.
There are some old m68k targets who were also using this chip,
so rather than poll the m68k user base, we simply cut out the
x86/Apricot support here in this commit.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cosmetic changes to drivers/isdn/gigaset/ev-layer.c and
drivers/isdn/gigaset/gigaset.h to improve readability.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange the gigaset_freecs() function to make it more readable,
and adapt gigaset_initcs() accordingly.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid forward declarations and remove a needless initialization.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware releases of Gigaset M105 do not accept AT+VLS=0 command
in DLE mode, so always leave DLE mode before sending the command.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up some of the readibility deterioration caused by last year's
ISDN whitespace coding style cleanup.
Note that the checkpatch complaints all apply to the state of the
source before this patch as well, and in many cases even more so.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete successive tests to the same location. rc was previously tested and
not subsequently updated. efx_phc_adjtime can return an error code, so the
call is updated so that is tested instead.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we write MAC address to pci config space byte by byte,
this means that we have an intermediate step where mac is wrong.
This patch introduced a new control command to set MAC address,
it's atomic.
VIRTIO_NET_F_CTRL_MAC_ADDR is a new feature bit for compatibility.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to send vq command to set mac address in
virtnet_set_mac_address(), so do this function moving.
Fixed a little issue of coding style.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 46d3ceab "tcp: TCP Small Queues" has severly degraded
performance for single connection RR workloads on HiperSockets with
MTU >=16K due to a conflict of the TCP Small Queues approach with our
buffer scan threshold which releases buffers not frequently enough yet.
This fix restores performance to the same level as before cited commit.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now, s390dbf entries for the cards are discarded as soon as the
device is removed. However, this will also bar us of all chances of
getting valuable debug information after a device has been removed.
This patch will keep the s390dbf entries around until the qeth module
is removed.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refer to virtual NICs instead of GuestLANs.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing port isolation mode 'forward' will now verify that the adjacent
switch port supports the required reflective relay (RR) mode. This patch adds
the required error handling for the cases where enabling port isolation mode
'forward' can now fail.
Furthermore, once established, we never fall back from one of the port
isolation modes to a non-isolated mode without further user-interaction.
This includes cases where the isolation mode was enabled successfully, but
ceases to work e.g. due to configuration changes at the switch port.
Finally, configuring an isolation mode with the device being offline
will make onlining the device fail permanently upon errors encountered until
either errors are resolved or the isolation mode is changed by the user to a
different mode.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove exports that are not used anywhere else.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous code did never retry any idx setup unless retries were done
for device offline/online at the beginning of the function.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reviewed-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the transmit DMA channel field in struct emac_priv
is txchan, not txch.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
