Setup a proper AGC config for the 340e, based on the Windows USB trace
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to set the dev.parent member on the dib7000p on its i2c master, or
else calls to request_firmware() will hit an oops in 2.6.31.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a sleep since in some cases the dib7000p wasn't online when being probed.
The optimal timing has not yet been determined.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the correct i2c bus to communicate with the tuner, and properly setup the
reset GPIO and i2c address.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide a frontend setup routine for the PCTV 340e which takes into account
the specific GPIO setup of the board.
Note that this patch does *not* take into account the xc4000 reset pin, which
is attached to the dib7000.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the board profile for the PCTV 340eSE, since that's what I have here
for development.
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver. I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).
[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Davide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The function "rc5_scan" in "dvb_usb.h" is returning invalid value.
The value should be returned "u16" but is returning "u8".
See example below in "drivers/media/dvb/dvb-usb/opera1.c":
send_key = (send_key & 0xffff) | 0x0100;
for (i = 0; i < ARRAY_SIZE(rc_map_opera1_table); i++) {
if (rc5_scan(&rc_map_opera1_table[i]) == (send_key & 0xffff)) {
*state = REMOTE_KEY_PRESSED;
*event = rc_map_opera1_table[i].keycode;
opst->last_key_pressed =
rc_map_opera1_table[i].keycode;
break;
}
opst->last_key_pressed = 0;
}
Signed-off-by: Manoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The info and err macros are already defined by the USB stack. Rename
these macros to avoid macro redefinition warnings.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The dbg, warn and info macros are already defined by the USB stack.
Rename these macros to avoid macro redefinition warnings.
Refactor lineshift in printouts.
Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Basically it is just same device as Anysee E7 S2 but made for
internal PCI(e) slot and motherboard USB connector.
Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Basically it is just same device as Anysee E7 TC but made for
internal PCI(e) slot and motherboard USB connector.
Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Attached is a patch which addresses a race condition in the DVB core
related to closing/reopening the DVB frontend device in quick
succession. This is the reason that devices such as the HVR-1300,
HVR-3000, and HVR-4000 have been failing to scan properly under MythTV
and w_scan.
The gory details of the race are described in the patch.
Devin
There is a race condition exhibited when channel scanners such as w_scan and
MythTV quickly close and then reopen the frontend device node.
Under normal conditions, the behavior is as follows:
1. Application closes the device node
2. DVB frontend ioctl calls dvb_frontend_release which sets
fepriv->release_jiffies
3. DVB frontend thread *eventually* calls dvb_frontend_is_exiting() which
compares fepriv->release_jiffies, and shuts down the thread if timeout has
expired
4. Thread goes away
5. Application opens frontend device
6. DVB frontend ioctl() calls ts_bus_ctrl(1)
7. DVB frontend ioctl() creates new frontend thread, which calls
dvb_frontend_init(), which has demod driver init() routine setup initial
register state for demod chip.
8. Tuning request is issued.
The race occurs when the application in step 5 performs the new open() call
before the frontend thread is shutdown. In this case the ts_bus_ctrl() call
is made, which strobes the RESET pin on the demodulator, but the
dvb_frontend_init() function never gets called because the frontend thread
hasn't gone away yet. As a result, the initial register config for the demod
is *never* setup, causing subsequent tuning requests to fail.
If there is time between the close and open (enough for the dvb frontend
thread to be torn down), then in that case the new frontend thread is created
and thus the dvb_frontend_init() function does get called.
The fix is to set the flag which forces reinitialization if we did in fact
call ts_bus_ctrl().
This problem has been seen on the HVR-1300, HVR-3000, and HVR-4000, and is
likely occuring on other designs as well where ts_bus_ctrl() actually strobes
the reset pin on the demodulator.
Note that this patch should supercede any patches submitted for the
1300/3000/4000 which remove the code that removes GPIO code in
cx8802_dvb_advise_acquire(), which have been circulating by users for some
time now...
Canonical tracking this issue in Launchpad 439163:
Thanks to Jon Sayers from Hauppauge and Florent Audebert from Anevia S.A. for
providing hardware to test/debug with.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jon Sayers <j.sayers@hauppauge.co.uk>
Cc: Florent Audebert <florent.audebert@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] v1.88 DM04/QQBOX Move remote to use rc_core dvb-usb-remote
[media] Add missing include guard to header file
[media] Inlined functions should be static
[media] Remove invalid parameter description
[media] cpia2: fix warning about invalid trigraph sequence
[media] s5p-csis: Add missing dependency on PLAT_S5P
[media] gspca/kinect: wrap gspca_debug with GSPCA_DEBUG
[media] fintek-cir: new driver for Fintek LPC SuperIO CIR function
[media] uvcvideo: Connect video devices to media entities
[media] uvcvideo: Register subdevices for each entity
[media] uvcvideo: Register a v4l2_device
[media] add V4L2-PIX-FMT-SRGGB12 & friends to docbook
[media] Documentation/DocBook: Rename media fops xml files
[media] Media DocBook: fix validation errors
[media] wl12xx: g_volatile_ctrl fix: wrong field set
[media] fix kconfig dependency warning for VIDEO_TIMBERDALE
[media] dm1105: GPIO handling added, I2C on GPIO added, LNB control through GPIO reworked
[media] Add support for M-5MOLS 8 Mega Pixel camera ISP
driver to use dvb-usb-remote.
The remote(s) generates 24 bit NEC codes, lme2510 keymaps redefined.
Other minor fixes
fix le warning.
make sure frontend is detached on firmware change.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Here is patch for GPIO's handling.
It allows to support I2C on GPIO's and per board LNB control through GPIO's.
Also incuded some support for Hendrik Skarpeid card.
For those, who needs to tweak the driver,
I think it is clear how to change and test GPIO's for LNB and other GPIO related stuff now.
[mchehab@redhat.com: I2C_CLASS_TV_DIGITAL is deprecated. removed to avoid breaking compilation]
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (247 commits)
[media] gspca - sunplus: Fix some warnings and simplify code
[media] gspca: Fix some warnings tied to 'no debug'
[media] gspca: Unset debug by default
[media] gspca - cpia1: Remove a bad conditional compilation instruction
[media] gspca - main: Remove USB traces
[media] gspca - main: Version change to 2.13
[media] gspca - stk014 / t613: Accept the index 0 in querymenu
[media] gspca - kinect: Remove __devinitdata
[media] gspca - cpia1: Fix some warnings
[media] video/Kconfig: Fix mis-classified devices
[media] support for medion dvb stick 1660:1921
[media] tm6000: fix uninitialized field, change prink to dprintk
[media] cx231xx: Add support for Iconbit U100
[media] saa7134 add new TV cards
[media] Use a more consistent value for RC repeat period
[media] cx18: Move spinlock and vb_type initialisation into stream_init
[media] tm6000: remove tm6010 sif audio start and stop
[media] tm6000: remove unused exports
[media] tm6000: add pts logging
[media] tm6000: change from ioctl to unlocked_ioctl
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
[mchehab@redhat.com: The same patch were sent by Alf and by Randoslaw.
I've applied the oldest version, just fixing the entry index]
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Tested-by: James Huk <huk256@gmail.com>
Tested-by: Alf Fahland <alf-f@gmx.de>
Signed-off-by: Radoslaw Warowny <radoslaww@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Holds the parameters detected by the demod.
- Updated on every call to get_frontend, either through ioctl or when
a frontend event occurs.
- Reset to input parameters after every call to set_frontend, tune or
search/track.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Drivers should be able to override properties returned to the user.
- The default values get prefilled from the cache.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Use const pointers and remove assignments.
- delivery_system already gets assigned by DTV_DELIVERY_SYSTEM
and dtv_property_cache_sync.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is supported in DVB-T2 mode, so added to the T/T2 frontend.
Signed-off-by: Steve Kerrison <steve@stevekerrison.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/drxd_hard.c: In function ‘DRX_Start’:
drivers/media/dvb/frontends/drxd_hard.c:2327: warning: enumeration value ‘BANDWIDTH_5_MHZ’ not handled in switch
drivers/media/dvb/frontends/drxd_hard.c:2327: warning: enumeration value ‘BANDWIDTH_10_MHZ’ not handled in switch
drivers/media/dvb/frontends/drxd_hard.c:2327: warning: enumeration value ‘BANDWIDTH_1_712_MHZ’ not handled in switch
[mchehab@redhat.com: removed the status = status assignment after the switch]
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[steve@stevekerrison.com: Remove private definitions from cxd2820r that existed before API was defined]
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Steve Kerrison <steve@stevekerrison.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- Return values should not be ORed. Abort early instead.
- Return -EINVAL instead of -1.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the remaining on-stack buffer for USB DMA transfer.
This patch also reduces the stack memory usage.
Cc: stable@kernel.org
Cc: Florian Mickler <florian@mickler.org>
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove old DVB-T2 freq module param and detect DVB-T/T2 automatically.
Implementation is trial and error, if DVB-T does not lock try DVB-T2
and vice versa. That's done by replacing normal DVBFE_ALGO_SW with
DVBFE_ALGO_CUSTOM which gives better control for tuning process.
DVB-C still uses normal software ZigZag, DVBFE_ALGO_SW.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make checkpatch.pl happy by fixing whitespaces introduced by
commit 79e8b8e3b8cbf67130247a3f6d25732373fe2f34
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change firmware download split, which I introduced few patch earlier,
a little bit to make it more readable as requested [1].
Anyhow, for some reason this seems to increase compiled binary size
52 bytes, on my AMD64 box, which is rather much for so small change.
[1] http://www.spinics.net/lists/linux-media/msg31968.html
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is very rare I2C adapter hardware which can provide 32kB I2C write
as one write. Add .i2c_wr_max option to set desired max packet size.
Split transaction to smaller pieces according to that option.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Bits 4 and 5 on register 02 should always be set to 1.
Opera1/Bsru6/z0194a/mantis_vp1033
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Issues with Register 02 causing spurious channel locking from standby.
Should have always bits 4 & 5 written to 1.
Lower nibble not used in any current driver. Usage if necessary can be
applied through initab to mcr_reg. stv0299 not out of standby before
writing inittab.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Improve PID filtering and program register 20 correctly.
Make sure stream_on message is sent if streaming is off, otherwise
PIDs are not registered.
Move mutex outside lme2510_enable_pid.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_buffer not inside mutex lock, waiting caller can alter buffer.
Static added to lme2510_exit and lme2510_exit_int.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Gate could close after first I2C message. On stv0288 it does.
Keep 2nd and 3rd message I2C gate control alive.
Remove unnecessary gate closing in this module.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In drivers/media/dvb/siano/smsusb.c we have this code:
...
kfree(dev);
sms_info("device %p destroyed", dev);
...
at least one static analysis tool (Coverity Prevent) complains about this
as a use-after-free bug.
While it's true that we do use the pointer variable after freeing it, the
only use is to print the value of the pointer, so there's not actually any
problem here. But still, silencing the complaint is trivial by just moving
the kfree() call below the sms_info(), so why not just do it?. It doesn't
change the workings of the code in any way, but it makes the tool shut up.
The patch below also removes a rather pointless blank line.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Return device errors to demuxer from on/off streamming and
pid filtering.
Please test this patch with all dvb-usb devices.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are a couple of places where mutex_unlock() is called even
if mutex_lock_interruptible() failed. The patch fixes the issue.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Avoid unnecessary DVB TS 188 sized packet copying from DMA buffer into stack.
Backtrack one 188 sized packet just after some garbage bytes when possible.
This obsoletes patch https://patchwork.kernel.org/patch/118147/
Signed-off-by: Marko Ristola <marko.ristola@kolumbus.fi>
Acked-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the second memory allocation in dib9000_attach() fails, we'll leak the
memory allocated by the first.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Cc: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A greatly simplified version of the PID Filter now added
back to the Driver.
The driver allows for the PID filter to be turned off.
applied after patch 683781.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register 42 bits 2,3,6 and 7 should be set to 0.
This gives difficult locking on some channels and may be compensated
for by other methods.
This affects any driver using the stv0288 frontend on the default
or earda inittab.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
stv0288 Register 42 bits 6 & 7 should be set to 0.
This is causing intermittent lock, the dvb-usb-lmedm04 driver uses
register 50 (auto fine mode) to correct for this, this register is
now returned to its default setting.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for TT S-1500 with BSBE1-D01A tuner.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems like 'adap->fe' test for NULL was meant to be before we dereference
that pointer.
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Acked-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Tested-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Signed-off-by: Florian Mickler <florian@mickler.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Signed-off-by: Florian Mickler <florian@mickler.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Signed-off-by: Florian Mickler <florian@mickler.org>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note: This change is tested to compile only as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If we need a bigger buffer, we reallocte a new buffer and free the old
one.
Note: This change is tested to compile only as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note: This change is tested to compile only as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Otherwise it is not obvious that vp702x_usb_in_op or vp702x_usb_out_op
will not interfere with any vp702x_usb_inout_op.
Note: This change is tested to compile only, as I don't have the
hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This sets up a buffer and a mutex protecting that buffer in
the struct vp702x_device_state.
The definition of struct vp702x_device_state is moved into the header
in order to use the buffer also in the frontend.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need a state struct for the dvb_usb_device.
In order to reduce confusion we rename the vp702x_state struct.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some whitespace, one linebreak and one unneded variable
initialization...
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Igor M. Liplianin <liplianin@tut.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Cc: Akihiro Tsukada <tskd2@yahoo.co.jp>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
usb_control_msg initiates (and waits for completion of) a dma transfer using
the supplied buffer. That buffer thus has to be seperately allocated on
the heap.
In lib/dma_debug.c the function check_for_stack even warns about it:
WARNING: at lib/dma-debug.c:866 check_for_stack
Note: This change is tested to compile only, as I don't have the hardware.
Signed-off-by: Florian Mickler <florian@mickler.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes the on-stack buffers for USB DMA transfers.
This is an alternative version of the patch discussed by Florian here:
http://thread.gmane.org/gmane.linux.kernel/1115695/
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove DEBUG define, key debug spew off of the module's debug param that
already exists.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the newly introduced KEY_IMAGES where appropriate, and standardize
on KEY_MEDIA for media center/application launcher button (such as the
Windows logo key on the Windows Media Center Ed. remotes).
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add some comments about known GPIO settings of supported board
versions.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After that Anysee I2C adapter is capable of one and two byte long
I2C addresses in case of read from I2C bus.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looks like it is IF route switch on IOE[0]. Set it correctly
to route signal from tuner to demod. Now it works for DVB-C too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is ZL10353, TDA10023 and TDA18212.
Tuner is inside of Samsung DNOD44CDH086A tuner module.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New models have new NXP TDA18212 silicon tuner.
Not tested yet due to lack of HW...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use board ID as base value when selecting correct hardware configuration.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Print firmware version as two digit long (change from 3 to 2).
Windows app have changed that too. First byte was hard coded as 0.
Change email list address to report non-working device to current one.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It can read more than one byte from I2C bus. Allow that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are still lots of 80-columns warnings and a few errors
at some tables, but changing them would require more work and
with probably not much gain.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The macro is defined as:
#define CHK_ERROR(s) if( (status = s)<0 ) break
This sucks, as makes harder to debug if something got wrong and
there are more than one level of loops. Also, violates CodingStyle.
Fixed by this simple perl script:
while (<>) { $f.=$_; };
$f=~ s,\n\#define CHK_ERROR[^\n]+\n,\n,;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s,\n(\t+)CHK_ERROR\((.*)\)\;,\n\1status = \2;\n\1if (status < 0)\n\1\tbreak;,g;
print $f;
Plus a few manual adjustments
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This file is big. It has 12000+ lines! Most of the defined stuff aren't
used anyware inside the driver, so we can just remove most of the lines
and still keep everything that have any interest for the driver.
If anyone ever need the other devices, it will be stored at git logs, so
it is easy to recover.
The diff result is impressive:
1 files changed, 1013 insertions(+), 12694 deletions(-)
rewrite drivers/media/dvb/frontends/drxd_map_firm.h (90%)
As a sideback effect, drxd driver will likely compile faster, and
checkpatch.pl can run on this file without taking (literally) hours.
The code cleanup was done using this small script:
$ for i in `perl -ne 'print "$1\n" if (m/define\s+([^\s+]+)/)' drxd_map_firm.h`; do if [ "`grep $i drivers/media/dvb/frontends/drxd*.[ch]`" != "" ] ; then echo $i; fi; done|sort|uniq >used_symbols
$ grep -f used_symbols drxd_map_firm.h >defines
And then deleting the old #define lines, replacing by "defines" file content.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Take a first cleanup pass over the sources to bring them closer to the
Linux coding style.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Abstract out the firmware for the drx-d so that it can be loaded by the
request_firmware() interface.
The firmware licensing permits free redistribution, and can be found here:
http://kernellabs.com/firmware/drxd
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the tuner is not actually behind an i2c gate, using the i2c gate control
function can wedge the i2c bus. Provide the ability to control on a per-board
basis whether it should be used.
Problem was noticed on the HVR-900 R2, where it resulted in the first tuning
attempt succeeding, and then all subsequent attempts to access the xc3028
being treated as failures (including the call to sleep the tuner).
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide the ability for the board configuration to specify whether to insert
the RS byte into the TS interconnect to the bridge, while not required for
the ngene in fact is required for the em28xx.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the drxd to the Makefile and Kconfig
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These are the original drx-d sources, extracted from Ralph Metzler's GPL'd
ngene driver. No modifications/cleanup have yet been made. In fact, no
measures have been taken to see if the code even compiles.
Signed-off-by Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The default for "verbose" is 0. Update description to match.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pci_setup_device() has saved the PCI revision in the pci_dev
struct since Linux 2.6.23. Use it.
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix issue where firmware does not release on cold reset.
Also, default firmware never cold resets in multi tuner
environment.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When queueing iso packets, the run time is dominated by the two
MMIO accesses that set the DMA context's wake bit. Because most
drivers submit packets in batches, we can save much time by
removing all but the last wakeup.
The internal kernel API is changed to require a call to
fw_iso_context_queue_flush() after a batch of queued packets.
The user space API does not change, so one call to
FW_CDEV_IOC_QUEUE_ISO must specify multiple packets to take
advantage of this optimization.
In my measurements, this patch reduces the time needed to queue
fifty skip packets from userspace to one sixth on a 2.5 GHz CPU,
or to one third at 800 MHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
We do not need slab allocations anymore in order to satisfy
streaming DMA mapping constraints, thanks to commit da28947e7e
"firewire: ohci: avoid separate DMA mapping for small AT payloads".
(Besides, the slab-allocated buffers that firewire-core, firewire-sbp2,
and firedtv used to provide for 8-byte write and lock requests were
still not fully portable since they crossed cacheline boundaries or
shared a cacheline with unrelated CPU-accessed data. snd-firewire-lib
got this aspect right by using an extra kmalloc/ kfree just for the
8-byte transaction buffer.)
This change replaces kmalloc'ed lock transaction scratch buffers in
firewire-core, firedtv, and snd-firewire-lib by local stack allocations.
Perhaps the most notable result of the change is simpler locking because
there is no need to serialize usages of preallocated per-device buffers
anymore. Also, allocations and deallocations are simpler.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
[media] ngene: Fix CI data transfer regression Fix CI data transfer regression introduced by previous cleanup.
[media] v4l: make sure drivers supply a zeroed struct v4l2_subdev
[media] Missing frontend config for LME DM04/QQBOX
[media] rc_core: avoid kernel oops when rmmod saa7134
[media] imon: add conditional locking in change_protocol
[media] rc: show RC_TYPE_OTHER in sysfs
[media] ite-cir: modular build on ppc requires delay.h include
[media] mceusb: add Dell transceiver ID
Fix CI data transfer regression introduced by previous cleanup.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (42 commits)
[media] media: vb2: correct queue initialization order
[media] media: vb2: fix incorrect v4l2_buffer->flags handling
[media] s5p-fimc: Add support for the buffer timestamps and sequence
[media] s5p-fimc: Fix bytesperline and plane payload setup
[media] s5p-fimc: Do not allow changing format after REQBUFS
[media] s5p-fimc: Fix FIMC3 pixel limits on Exynos4
[media] tda18271: update tda18271c2_rf_cal as per NXP's rev.04 datasheet
[media] tda18271: update tda18271_rf_band as per NXP's rev.04 datasheet
[media] tda18271: fix bad calculation of main post divider byte
[media] tda18271: prog_cal and prog_tab variables should be s32, not u8
[media] tda18271: fix calculation bug in tda18271_rf_tracking_filters_init
[media] omap3isp: queue: Don't corrupt buf->npages when get_user_pages() fails
[media] v4l: Don't register media entities for subdev device nodes
[media] omap3isp: Don't increment node entity use count when poweron fails
[media] omap3isp: lane shifter support
[media] omap3isp: ccdc: support Y10/12, 8-bit bayer fmts
[media] media: add missing 8-bit bayer formats and Y12
[media] v4l: add V4L2_PIX_FMT_Y12 format
cx23885: Fix stv0367 Kconfig dependency
[media] omap3isp: Use isp xclk defines
...
Fix up trivial conflict (spelink errurs) in drivers/media/video/omap3isp/isp.c
Device is based on STV0903 demod and STV6110x tuner
Signed-off-by: Oleg Roitburd <oroitburd@gmail.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Seems like 'adap->fe' test for NULL was meant to be before we dereference
that pointer.
Signed-off-by: Mariusz Kozlowski <mk@lab.zgora.pl>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the warning about bad names for sys-fs and other kernel-things. The flexcop-pci driver was using '/'-characters in it, which is not good.
This has been fixed in several attempts by several people, but obviously never made it into the kernel.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Cc: Steffen Barszus <steffenbpunkt@googlemail.com>
Cc: Boris Cuber <me@boris64.net>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix typo introduced in b4d6046e84.
Spotted by Dr. David Alan Gilbert. Thanks for that.
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Cc: Dr. David Alan Gilbert <linux@treblig.org>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (442 commits)
[media] videobuf2-dma-contig: make cookie() return a pointer to dma_addr_t
[media] sh_mobile_ceu_camera: Do not call vb2's mem_ops directly
[media] V4L: soc-camera: explicitly require V4L2_BUF_TYPE_VIDEO_CAPTURE
[media] v4l: soc-camera: Store negotiated buffer settings
[media] rc: interim support for 32-bit NEC-ish scancodes
[media] mceusb: topseed 0x0011 needs gen3 init for tx to work
[media] lirc_zilog: error out if buffer read bytes != chunk size
[media] lirc: silence some compile warnings
[media] hdpvr: use same polling interval as other OS
[media] ir-kbd-i2c: pass device code w/key in hauppauge case
[media] rc/keymaps: Remove the obsolete rc-rc5-tv keymap
[media] remove the old RC_MAP_HAUPPAUGE_NEW RC map
[media] rc/keymaps: Rename Hauppauge table as rc-hauppauge
[media] rc-rc5-hauppauge-new: Fix Hauppauge Grey mapping
[media] rc-rc5-hauppauge-new: Add support for the old Black RC
[media] rc-rc5-hauppauge-new: Add the old control to the table
[media] rc-winfast: Fix the keycode tables
[media] a800: Fix a few wrong IR key assignments
[media] opera1: Use multimedia keys instead of an app-specific mapping
[media] dw2102: Use multimedia keys instead of an app-specific mapping
...
Fix up trivial conflicts (remove/modify and some real conflicts) in:
arch/arm/mach-omap2/devices.c
drivers/staging/Kconfig
drivers/staging/Makefile
drivers/staging/dabusb/dabusb.c
drivers/staging/dabusb/dabusb.h
drivers/staging/easycap/easycap_ioctl.c
drivers/staging/usbvideo/usbvideo.c
drivers/staging/usbvideo/vicam.c
The rc-hauppauge-new map is a messy thing, as it bundles 3
different remote controllers as if they were just one,
discarding the address byte. Also, some key maps are wrong.
With the conversion to the new rc-core, it is likely that
most of the devices won't be working properly, as the i2c
driver and the raw decoders are now providing 16 bits for
the remote, instead of just 8.
delete mode 100644 drivers/media/rc/keymaps/rc-hauppauge-new.c
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
There are two "hauppauge-new" keymaps, one with protocol
unknown, and the other with the protocol marked accordingly.
However, both tables are miss-named.
Also, the old rc-hauppauge-new is broken, as it mixes
three different controllers as if they were just one.
This patch solves half of the problem by renaming the
correct keycode table as just rc-hauppauge. This table
contains the codes for the four different types of
remote controllers found on Hauppauge cards, properly
mapped with their different addresses.
create mode 100644 drivers/media/rc/keymaps/rc-hauppauge.c
delete mode 100644 drivers/media/rc/keymaps/rc-rc5-hauppauge-new.c
[Jarod: fix up RC_MAP_HAUPPAUGE defines]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
This driver uses an app-specific keymap for one of the tables. This
is wrong. Instead, use the standard keycodes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
This driver uses an app-specific keymap for one of the tables. This
is wrong. Instead, use the standard keycodes.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
On a few places, KEY_MHP were used for snapshots. However, KEY_CAMERA
is used for it on all the other keyboards that have a snapshot/Picture
button.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
The CellsCoeffs arrays are [3][6][5] not [2][6][5].
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We use err to store negative error codes so it should be signed. And
if we return an error from stv0367_get_tuner_freq() that needs to be
handled properly as well. (param->frequency is a u32).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use 32 bit decoding to add support for more than one variant of remote
control.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Old versions of these boxes have the BS2F7HZ0194 tuner module on
both the LME2510 and LME2510C.
Firmware dvb-usb-lme2510-s0194.fw and/or dvb-usb-lme2510c-s0194.fw
files are required.
See Documentation/dvb/lmedm04.txt
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Thu, 17 Feb 2011, Matthias Schwarzott wrote:
> On Sunday 06 February 2011, Jesper Juhl wrote:
> > If the memory allocation to 'state' succeeds but we jump to the 'error'
> > label before 'state' is assigned to fe->tuner_priv, then the call to
> > 'zl10036_release(fe)' at the 'error:' label will not free 'state', but
> > only what was previously assigned to 'tuner_priv', thus leaking the memory
> > allocated to 'state'.
> > There are may ways to fix this, including assigning the allocated memory
> > directly to 'fe->tuner_priv', but I did not go for that since the
> > additional pointer derefs are more expensive than the local variable, so I
> > just added a 'kfree(state)' call. I guess the call to 'zl10036_release'
> > might not even be needed in this case, but I wasn't sure, so I left it in.
> >
> Yeah, that call to zl10036_release can be completely eleminated.
> Another thing is: jumping to the error label only makes sense when memory was
> already allocated. So the jump in line 471 can be replaced by "return NULL",
> as the other error handling before allocation:
> if (NULL == config) {
> printk(KERN_ERR "%s: no config specified", __func__);
> goto error;
> }
>
> I suggest to improve the patch to clean the code up when changing that.
>
> But I am fine with commiting this patch also if you do not want to change it.
>
Thank you for your feedback. It makes a lot of sense.
Changing it is not a problem :)
How about the updated patch below?
If the memory allocation to 'state' succeeds but we jump to the 'error'
label before 'state' is assigned to fe->tuner_priv, then the call to
'zl10036_release(fe)' at the 'error:' label will not free 'state', but
only what was previously assigned to 'tuner_priv', thus leaking the memory
allocated to 'state'.
This patch fixes the leak and also does not jump to 'error:' before mem
has been allocated but instead just returns. Also some small style
cleanups.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split FW download packages smarter way and bug free. Implementation is
based of Andrea Merello's example he provided for tda18218 driver.
Count remaining FW bytes down in loop instead of division and modulo
combination used earlier.
Thanks to: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Quick test shows that FW must be running before other checks
so make it happen earlier.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Split FW download packages smarter way and bug free. Implementation is
based of Andrea Merello's example he provided for tda18218 driver.
Count remaining FW bytes down in loop instead of division and modulo
combination used earlier.
Thanks-to: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Patch from Ian Armstrong.
I've encountered a couple of problems with the current af9015 driver as
supplied with the 2.6.37 kernel, that the attached patch appears to fix. (I've
generated this patch against the current v4l-dvb git).
Some key-presses are lost. A key-press is only generated upon 'valid' data
(buf[14] == (u8) ~buf[15]), but the buffer is wiped before this check.
Sometimes the 15th byte has not been set at the time of read, so the data
isn't valid & ignored. On the next poll the 15th byte has been set, but the
rest of the data was wiped previously, so the data is still invalid & the key
is lost.
Weird repeat error, where an old key press is sometimes repeated in error. ie.
button sequence '1 (pause) 2 (pause) 3 (pause) 4' generates output like '1
(pause) 2 (pause) 23 (pause) 4'. The current driver zeroes the data for the
key pushed, but sometimes this data is already zero but with other bytes set
suggesting a repeat code. This results in the last key being incorrectly
repeated.
This patch attempts to reduce the risk of a missed key-press & also stop the
random repeat of an old key-press when a new key is pressed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/stv0367.c: In function 'stv0367ter_lock_algo':
drivers/media/dvb/frontends/stv0367.c:1315:2: warning: cast from pointer to integer of different size
Use %p to print addresses instead of 0x%x.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Related to Acorp DS120 and some revisions of DVBWorld DW2102.
If you read three or more registers at one time, you get wrong value for third etc.
Actually, it didn't affect the driver as it reads registers only by one at a time.
But it needs to correct.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prof 7500 and TeVii s630, s660, s480 works better now
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Prof 7500 and TeVii s630, s660, s480 works faster now
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card consist of PCI to USB bridge and USB DVB-S2 receiver.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is taken from another tree, where it is modified.
Patch to fix that
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Simptoms:
After zapping DVB-S2 channel searching for DVB-S tooks long time.
Now it takes less than a second.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
dib9000_mbx_send_attr() returns an int. It doesn't work to save
negative error codes in an unsigned char, so I've made "ret" an int
type.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on staging 2.6.39.
This patch is based on Veit Berwig's work.
Signed-off-by: Lukas Fisch <lukas.fisch@gmail.com>
Thanks-to: Veit Berwig <veit.Berwig@fimi.landsh.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
kmalloc() can fail so check whether state->internal is NULL.
append_internal() can return NULL on allocation failures so check that.
Also if we hit the error condition later in the function then there is
a memory leak and we need to call remove_dev() to fix it.
Also Oliver Endriss pointed out an additional leak that I missed in the
first version of this patch.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All necessary parameters already stored in frontend cache.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Variable 'retune' does not make sense.
Loop is not needed for only one try.
Remove unnecessary dprintk's.
Remove a lot of debug messages and delays.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card consists of a PCI-e to USB Host Controller and
two TeVii S660 equivalent cards.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are two TeVii s660 modifications with different LNB power control
implementations. It is safe to call both methods for each card.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
RC keys structure for Prof 1100 already defined, so remove extra initialization.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Code changed for dw2102, stv0900 in order to achieve that.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
MarkusF wrote:
I accidently got a Terratec Cinergy S2 USB HD (instead of a Terratec Cinergy S2 PCI HD).
I found in the windows driver, that the driver is for the usb ids:
0CCD:00A8
1F4D:3000
The dvb-s2 usb adapter has the id 0CCD-00A8.
So I patches your driver and added the usb id, where the 1F4D:3000 is
and it worked (after I downloaded the firmware dvb-fe-ds3000.fw).
w_scan found the channels and vdr is working fine.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch we can use only one card type from list due to
sharing one firmware name. Now it's fixed.
Also driver tries to attach only appropriate demod for this cards.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In drivers/media/dvb/ttusb-budget/dvb-ttusb-budget.c:ttusb_boot_dsp() we
need to call release_firmware(fw) before returning or we'll leak - no
matter if we succeed or fail.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This tuner PLL has missing initialisation settings resulting in
haphazard tuning. The PLL LPF was set to just 22000 symbol rate.
Basically, the module is a Sharp BS2F7HZ0194 (STV0299+IX2410)
I have had problems implementing the PLL in a new driver and
did not want to break the IX2410 out of the PLL.
This applies to DW2102, DM1105, CX88 and OPERA1 drivers.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since the drivers/ieee1394/ backend was removed from firedtv, its I/O no
longer needs to be abstracted as exchangeable backend methods.
Also, ieee1394 variants of module and device probe and removal are no
longer there. Move module probe and removal into firedtv-fw.c where
device probe and removal are implemented.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Speed up tuning, as firmware is not necessary to load every attempt to tune
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Decrease firmware loading time. Before it is ~4000 i2c calls,
now it is ~256 i2c calls to load ds3000 firmware.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
TeVii s480 works fine with that on DVB-S2 channels
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make some initializations in init, not in tune function
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The card based on cx23885 PCI-e brige. Altera FPGA for CI,
multistandard demods stv0367 from STM for QAM & OFDM, Xcieve xc5000 tuners
and additional cx25840 for second analog input.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The STV0367 is a multi-standard demodulator which is
capable of processing DVB-T as well as DVB-C signals.
It is fully compliant with DVB-T and DVB-C
recommendations for broadcast services.
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/ieee1394/ has been removed in Linux 2.6.37. The corresponding
backend code in firedtv is no longer built in now and can be deleted.
Firedtv continues to work with drivers/firewire/.
Also, fix a Kconfig menu comment: Removal of CONFIG_IEEE1394 made the
"Supported FireWire (IEEE 1394) Adapters" comment disappear; bring it back
with corrected dependency.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reviewed-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver is abusing the kernel<=>userspace API, due to the lack of a
proper solution for it. A discussion were done at:
http://www.mail-archive.com/linux-media@vger.kernel.org/msg22196.html
But there's not a solution for it yet. So, move the driver to staging, while
we don't have a final solution.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
22kHz workaround must also be performed for the 2nd frontend.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Refactored code for channel initialisation and release:
- Do not create device nodes which are not required.
- Better error handling.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Do not clear registers ACLC/BCLC in DVB-S2 mode for Cut <= 20.
Otherwise, the demod could lose the lock periodically.
Verified with cineS2 and Duoflex.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixed typos in register macros.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add dvb net device.
Note that the physical address must be setup manually.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Implement shutdown workaround for some chipsets.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver for the Common Interface Controller CXD2099AR.
Supports the CI of the cineS2 DVB-S2.
For now, data is passed through '/dev/dvb/adapterX/sec0':
- Encrypted data must be written to 'sec0'.
- Decrypted data can be read from 'sec0'.
- Setup the CAM using device 'ca0'.
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If tuner initialisation failed, the frontend node was not removed.
When the frontend was opened, a kernel oops occurred...
This is the first step to improve error handling during initialisation.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support up to 4 tuners for cineS2 v5, duoflex & mystique v2.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Card driver may supply its own lock routine now.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The STV0900 features two demodulator paths in one chip. Thus it is not
possible to use the generic power off function of the chip when sending
one of them to standby. The other path will stop working in that case.
The sleep function now switches off functionality specific to the demod
path. The global stuff is only switched off, when both paths are in
sleep mode. The wakeup function always turns on the global functionality
and then works specific to the path.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ERROR: switch and case should be at the same indent
switch (ch->u.ofdm.transmission_mode) {
[...]
+ case TRANSMISSION_MODE_4K:
WARNING: please, no spaces at the start of a line
+ case TRANSMISSION_MODE_4K:$
ERROR: switch and case should be at the same indent
switch (ch->u.ofdm.transmission_mode) {
[...]
+ case TRANSMISSION_MODE_4K:
WARNING: please, no spaces at the start of a line
+ case TRANSMISSION_MODE_4K:$
ERROR: switch and case should be at the same indent
switch (ch->u.ofdm.transmission_mode) {
[...]
+ case TRANSMISSION_MODE_4K:
WARNING: please, no spaces at the start of a line
+ case TRANSMISSION_MODE_4K:$
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds support for the SoC DiB7090 DVB-T demodulator and its
melt-in UHF/VHF RF tuner.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patchs add initial support for the DiB9000-device. This
demodulator is firmware-driven.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds several performance improvements and prepares the
usage of firmware-based devices.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds the possibitity to use different I2C-ports to talk to
slave-devices than the standard ones.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch adds a set a functions which allow the handling of multiple
demodulator in a diversity reception chain.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This commit adds a function to the DiB0700 USB driver which allows
drivers to change the I2C clock speed.
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/dvb-usb/technisat-usb2.c: In function ‘technisat_usb2_disconnect’:
drivers/media/dvb/dvb-usb/technisat-usb2.c:770: warning: ‘cancel_rearming_delayed_work’ is deprecated (declared at include/linux/workqueue.h:421)
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch is adding support for Technisat's new USB2.0 DVB-S/S2 receiver
device. The development was sponsored by Technisat.
The Green led is toggle depending on the frontend-state. The Red LED is turned
on all the time.
The MAC address reading from the EEPROM along with the
LRC-method to check whether its valid.
Support for the IR-receiver of the Technisat USB2 box. The keys of
small, black remote-control are built-in, repeated key behaviour are
simulated.
The i2c-mutex of the dvb-usb-structure is used as a general mutex for
USB requests, as there are 3 threads racing for atomic requests
consisting of multiple usb-requests.
A module option is there which disables the toggling of LEDs by the
driver on certain triggers. Useful when being used in a "dark"
environment.
[mchehab@redhat.com: Fix merge conflicts with RC renaming patches]
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some backends want to receive the full transport stream including
uncorrected packets. To have that feature this patchs add a field to
the config-structure called TEI (transport stream error indicator).
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch STV090X adds and exports a function to control the GPIOs of
the stv090x-devices.
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Martin Wilks <m.wilks@technisat.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (64 commits)
Input: tsc2005 - remove 'disable' sysfs attribute
Input: tsc2005 - add open/close
Input: tsc2005 - handle read errors from SPI layer
Input: tsc2005 - do not rearm timer in hardirq handler
Input: tsc2005 - don't use work for 'pen up' handling
Input: tsc2005 - do not use 0 in place of NULL
Input: tsc2005 - use true/false for boolean variables
Input: tsc2005 - hide selftest attribute if we can't reset
Input: tsc2005 - rework driver initialization code
Input: tsc2005 - set up bus type in input device
Input: tsc2005 - set up parent device
Input: tsc2005 - clear driver data after unbinding
Input: tsc2005 - add module description
Input: tsc2005 - remove driver banner message
Input: tsc2005 - remove incorrect module alias
Input: tsc2005 - convert to using dev_pm_ops
Input: tsc2005 - use spi_get/set_drvdata()
Input: introduce tsc2005 driver
Input: xen-kbdfront - move to drivers/input/misc
Input: xen-kbdfront - add grant reference for shared page
...
This patch adds the pid filtering for the dib7000M demod. It also
corrects the pid filtering for the dib7700 based board. It should
prevent an oops, when using dib7700p based board.
References: https://bugzilla.novell.com/show_bug.cgi?id=644807
Signed-off-by: Olivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: Patrick Boettcher <patrick.boettcher@dibcom.fr>
Tested-by: Pavel SKARKA <paul.sp@seznam.cz>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver Version v1.75 Kernel oops appears in 2.6.37-rc8 in
lme_firmware_switch because of a memcpy to a const char.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
All users of old style get/setkeycode methids have been converted so
it is time to retire them.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (101 commits)
[media] staging/lirc: fix mem leaks and ptr err usage
[media] hdpvr: reduce latency of i2c read/write w/recycled buffer
[media] hdpvr: enable IR part
[media] rc/mceusb: timeout should be in ns, not us
[media] v4l2-device: fix 'use-after-freed' oops
[media] v4l2-dev: don't memset video_device.dev
[media] zoran: use video_device_alloc instead of kmalloc
[media] w9966: zero device state after a detach
[media] v4l: Fix a use-before-set in the control framework
[media] v4l: Include linux/videodev2.h in media/v4l2-ctrls.h
[media] DocBook/v4l: update V4L2 revision and update copyright years
[media] DocBook/v4l: fix validation error in dev-rds.xml
[media] v4l2-ctrls: queryctrl shouldn't attempt to replace V4L2_CID_PRIVATE_BASE IDs
[media] v4l2-ctrls: fix missing 'read-only' check
[media] pvrusb2: Provide more information about IR units to lirc_zilog and ir-kbd-i2c
[media] ir-kbd-i2c: Add back defaults setting for Zilog Z8's at addr 0x71
[media] lirc_zilog: Update TODO.lirc_zilog
[media] lirc_zilog: Add Andy Walls to copyright notice and authors list
[media] lirc_zilog: Remove useless struct i2c_driver.command function
[media] lirc_zilog: Remove unneeded tests for existence of the IR Tx function
...
The meaning of CONFIG_EMBEDDED has long since been obsoleted; the option
is used to configure any non-standard kernel with a much larger scope than
only small devices.
This patch renames the option to CONFIG_EXPERT in init/Kconfig and fixes
references to the option throughout the kernel. A new CONFIG_EMBEDDED
option is added that automatically selects CONFIG_EXPERT when enabled and
can be used in the future to isolate options that should only be
considered for embedded systems (RISC architectures, SLOB, etc).
Calling the option "EXPERT" more accurately represents its intention: only
expert users who understand the impact of the configuration changes they
are making should enable it.
Reviewed-by: Ingo Molnar <mingo@elte.hu>
Acked-by: David Woodhouse <david.woodhouse@intel.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Greg KH <gregkh@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robin Holt <holt@sgi.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After a recent update of xf86-input-evdev and xorg-server, I noticed
that X11 applications did not receive keypresses from the FireDTV
infrared remote control anymore. Instead, the Xorg log featured lots of
"FireDTV remote control: dropping event due to full queue!"
exclamations. The Linux console did not have an issue with the
FireDTV's RC though.
The fix is to insert EV_SYN events after the key-down/-up events.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
info->num comes from the user. It's type int. If the user passes
in a negative value that would cause memory corruption.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We may leak the storage allocated to 'state' in
drivers/media/dvb/frontends/ix2505v.c::ix2505v_attach() on error, as
it is too early to be able to call ix2505v_release().
This patch makes sure we free the allocated memory in the failure case.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to a hard to track bug between tda829x/tda18271/saa7134, tda829x
wants to go to analog mode during DVB initialization, causing some
I2C errors.
The analog failure doesn't cause any harm, as the device were already
properly initialized in analog mode. However, the failure at the digital
mode causes the frontend mb86a20s to not initialize. Fortunately, at
least on my tests, it was possible to detect that the device is a
mb86a20s before the failure.
What happens is that tda8290 is a very bad boy: during DVB setup, it
keeps insisting to call tda18271 analog_set_params, that calls
tune_agc code. The tune_agc code calls saa7134 driver, changing the
value of GPIO 27, switching from digital to analog mode and disabling
the access to mb86a20s, as, on Kworld SBTVD, the same GPIO used
to switch the hardware AGC mode seems to be used to enable the I2C
switch that allows access to the frontend (mb86a20s).
So, a call to analog_set_params ultimately disables the access to
the frontend, and causes a failure at the init frontend logic.
This patch is a workaround for this issue: it simply checks if the
frontend init had any failure. If so, it will init the frontend when
some DTV application will try to set DVB mode.
Even being a hack for Kworld SBTVD to work, and assumning that we could
teach tda8290 to be a good boy, this is actually an improvement at the
frontend driver, as it will be more reliable to initialization failures.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A script replaced err var to rc. Howerver, this script gambled
"error" string, changing it to "rcor". Revert that bad change.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes Fedora 14 bug: https://bugzilla.redhat.com/show_bug.cgi?id=667157
There are a few bugs at the code that generates the scancode at dib0700:
- RC keycode is wrong (it outputs a 24 bits keycode);
- NEC extended outputs a keycode that have endiannes issues;
- keycode tables for NEC extended remotes need to be updated.
The last issue need to be done as we get reports, as we don't have
the complete NEC-extended keycodes at the dibcom table.
This patch fixes the first two issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
IF freq for DVB-T 7 MHz and 8 MHz was set slightly wrong. Due to that it
didn't worked at all (?) for 7 MHz channels and most likely performance
was dropped for 8 MHz channels.
That bug was pointed by few people during last two months. Thank you.
Trivial fix. Compile tested only due to lack of proper HW and signal.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Romolo Manfredini <romoloman@hotmail.com>
Cc: Alireza Moini <alireza.moini@silverbrookresearch.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
usb: don't use flush_scheduled_work()
speedtch: don't abuse struct delayed_work
media/video: don't use flush_scheduled_work()
media/video: explicitly flush request_module work
ioc4: use static work_struct for ioc4_load_modules()
init: don't call flush_scheduled_work() from do_initcalls()
s390: don't use flush_scheduled_work()
rtc: don't use flush_scheduled_work()
mmc: update workqueue usages
mfd: update workqueue usages
dvb: don't use flush_scheduled_work()
leds-wm8350: don't use flush_scheduled_work()
mISDN: don't use flush_scheduled_work()
macintosh/ams: don't use flush_scheduled_work()
vmwgfx: don't use flush_scheduled_work()
tpm: don't use flush_scheduled_work()
sonypi: don't use flush_scheduled_work()
hvsi: don't use flush_scheduled_work()
xen: don't use flush_scheduled_work()
gdrom: don't use flush_scheduled_work()
...
Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
Based on Waling Dijkstra's discovery that the IR works the same as
on the TT-1500, this patch has been rewritten to fit with the
rc_core infrastructure.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The v4l core sets the v4l2_input.capabilities field based on the supplied
v4l2_ioctl_ops. However, several drivers do a memset or memcpy of the v4l2_input
struct, thus overwriting that field incorrectly.
Either remove the memset (which is already done by the v4l core), or add the
proper capabilities field in case of a memcpy.
The same is also true for v4l2_output, but that only affected the ivtv driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These devices do not return the full command+address, so set
scanmask accordingly.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/dvb/frontends/af9013.c: In function ‘af9013_update_signal_strength.clone.0’:
drivers/media/dvb/frontends/af9013.c:967:6: warning: ‘ret’ may be used uninitialized in this function
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A few typos at the driver are causing the following warnings:
drivers/media/dvb/frontends/stv090x.c: In function ‘stv090x_start_search’:
drivers/media/dvb/frontends/stv090x.c:1486:27: warning: comparison between ‘enum stv090x_search’ and ‘enum stv090x_delsys’
drivers/media/dvb/frontends/stv090x.c:1487:24: warning: comparison between ‘enum stv090x_search’ and ‘enum stv090x_delsys’
drivers/media/dvb/frontends/stv090x.c: In function ‘stv090x_optimize_track’:
drivers/media/dvb/frontends/stv090x.c:2943:2: warning: case value ‘4’ not in enumerated type ‘enum stv090x_delsys’
The first two are due to the lack of using the delsys types
STV090x_DVBS1/STV090x_DSS
instead of
STV090x_SEARCH_DVBS1/STV090x_SEARCH_DSS
The second one is due to the usage of STV090x_UNKNOWN (enum stv090x_modulation)
instead of STV090x_ERROR (enum stv090x_delsys).
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
